Mechanical Properties and Dislocation Structure of Single Crystal Cdte Deformed in Compression at 300°C

1976 ◽  
Vol 34 ◽  
pp. 592-593
Author(s):  
Ernest L. Hall ◽  
J. B. Vander Sande
Keyword(s):  
Mechanical Properties ◽  
Single Crystal ◽  
Dislocation Structure ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Strain Curve ◽  
Optical Devices ◽  
Semiconductor Compound ◽  
Wide Range ◽  
Sample Orientation

The present paper describes research on the mechanical properties and related dislocation structure of CdTe, a II-VI semiconductor compound with a wide range of uses in electrical and optical devices. At room temperature CdTe exhibits little plasticity and at the same time relatively low strength and hardness. The mechanical behavior of CdTe was examined at elevated temperatures with the goal of understanding plastic flow in this material and eventually improving the room temperature properties. Several samples of single crystal CdTe of identical size and crystallographic orientation were deformed in compression at 300°C to various levels of total strain. A resolved shear stress vs. compressive glide strain curve (Figure la) was derived from the results of the tests and the knowledge of the sample orientation.

On the use of Ozawa/Flynn/Wall method to determine aging activation energy for elastomers

2021 ◽  
pp. 009524432110203
Author(s):  
Sudhir Bafna
Keyword(s):  
Mechanical Properties ◽  
Activation Energy ◽  
Weight Loss ◽  
Oxygen Consumption ◽  
Dwell Time ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Degradation Mechanism ◽  
Kinetics Of ◽  
Wall Method

It is often necessary to assess the effect of aging at room temperature over years/decades for hardware containing elastomeric components such as oring seals or shock isolators. In order to determine this effect, accelerated oven aging at elevated temperatures is pursued. When doing so, it is vital that the degradation mechanism still be representative of that prevalent at room temperature. This places an upper limit on the elevated oven temperature, which in turn, increases the dwell time in the oven. As a result, the oven dwell time can run into months, if not years, something that is not realistically feasible due to resource/schedule constraints in industry. Measuring activation energy (Ea) of elastomer aging by test methods such as tensile strength or elongation, compression set, modulus, oxygen consumption, etc. is expensive and time consuming. Use of kinetics of weight loss by ThermoGravimetric Analysis (TGA) using the Ozawa/Flynn/Wall method per ASTM E1641 is an attractive option (especially due to the availability of commercial instrumentation with software to make the required measurements and calculations) and is widely used. There is no fundamental scientific reason why the kinetics of weight loss at elevated temperatures should correlate to the kinetics of loss of mechanical properties over years/decades at room temperature. Ea obtained by high temperature weight loss is almost always significantly higher than that obtained by measurements of mechanical properties or oxygen consumption over extended periods at much lower temperatures. In this paper, data on five different elastomer types (butyl, nitrile, EPDM, polychloroprene and fluorocarbon) are presented to prove that point. Thus, use of Ea determined by weight loss by TGA tends to give unrealistically high values, which in turn, will lead to incorrectly high predictions of storage life at room temperature.

scholarly journals Comparison of Mechanical and Microstructural Properties of as-Cast Al-Cu-Mg-Ag Alloys: Room Temperature vs. High Temperature

Crystals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1330
Author(s):  
Muhammad Farzik Ijaz ◽  
Mahmoud S. Soliman ◽  
Ahmed S. Alasmari ◽  
Adel T. Abbas ◽  
Faraz Hussain Hashmi
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Mechanical Testing ◽  
Tensile Testing ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Microstructural Properties ◽  
Testing Environments ◽  
Mechanical And Microstructural Properties ◽  
Mg Content

Unfolding the structure–property linkages between the mechanical performance and microstructural characteristics could be an attractive pathway to develop new single- and polycrystalline Al-based alloys to achieve ambitious high strength and fuel economy goals. A lot of polycrystalline as-cast Al-Cu-Mg-Ag alloy systems fabricated by conventional casting techniques have been reported to date. However, no one has reported a comparison of mechanical and microstructural properties that simultaneously incorporates the effects of both alloy chemistry and mechanical testing environments for the as-cast Al-Cu-Mg-Ag alloy systems. This preliminary prospective paper presents the examined experimental results of two alloys (denoted Alloy 1 and Alloy 2), with constant Cu content of ~3 wt.%, Cu/Mg ratios of 12.60 and 6.30, and a constant Ag of 0.65 wt.%, and correlates the synergistic comparison of mechanical properties at room and elevated temperatures. According to experimental results, the effect of the precipitation state and the mechanical properties showed strong dependence on the composition and testing environments for peak-aged, heat-treated specimens. In the room-temperature mechanical testing scenario, the higher Cu/Mg ratio alloy with Mg content of 0.23 wt.% (Alloy 1) possessed higher ultimate tensile strength when compared to the low Cu/Mg ratio with Mg content of 0.47 wt.% (Alloy 2). From phase constitution analysis, it is inferred that the increase in strength for Alloy 1 under room-temperature tensile testing is mainly ascribable to the small grain size and fine and uniform distribution of θ precipitates, which provided a barrier to slip by deaccelerating the dislocation movement in the room-temperature environment. Meanwhile, Alloy 2 showed significantly less degradation of mechanical strength under high-temperature tensile testing. Indeed, in most cases, low Cu/Mg ratios had a strong influence on the copious precipitation of thermally stable omega phase, which is known to be a major strengthening phase at elevated temperatures in the Al-Cu-Mg-Ag alloying system. Consequently, it is rationally suggested that in the high-temperature testing scenario, the improvement in mechanical and/or thermal stability in the case of the Alloy 2 specimen was mainly due to its compositional design.

Influences of the γ′ Phase on the Mechanical Properties of a Nickel-Based Single Crystal Superalloy

2021 ◽  
Vol 1023 ◽  
pp. 45-52
Author(s):  
Xiao Yan Wang ◽  
Meng Li ◽  
Zhi Xun Wen
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Single Crystal ◽  
Tensile Properties ◽  
Room Temperature ◽  
Solution Treatment ◽  
Single Crystal Superalloy ◽  
Original Material ◽  
Solid Solution Treatment ◽  
The Matrix

After solid solution treatment at 1335°C for 4 hours and cooling to room temperature at different rate, the nickel-based single crystal superalloy were made into three kinds of nickel-based single crystal superalloy materials containing different size γ′ phases, respectively. The tensile test of I-shaped specimens was carried out at 980°C, and their effect of γ′ phase microstructure on the tensile properties was studied. The results show that the yielding strength of the material air-cooled to room temperature was lower than that with cooling rate at 0.15°C/s, but both of them were lower than the yielding strength of original material. Little difference was found on the elastic modulus of I-shaped specimens made of three kinds of materials. When the cubic degree of the γ′ phase is higher and the size is larger, the tensile properties of the material is better, which can be attributed to the larger size and narrower channel of the matrix phase that lead to higher dislocation resistance.

Effect of Ca and Sr Content on Elevated Temperatures Mechanical Properties of a Cast AZ91 Magnesium Alloy

2007 ◽  
Vol 26-28 ◽  
pp. 141-144
Author(s):  
Ippei Takeuchi ◽  
Kinji Hirai ◽  
Yorinobu Takigawa ◽  
Tokuteru Uesugi ◽  
Kenji Higashi
Keyword(s):  
Mechanical Properties ◽  
Magnesium Alloy ◽  
Creep Resistance ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Tensile Tests ◽  
Az91 Magnesium Alloy ◽  
Additional Amount ◽  
Az91 Magnesium ◽  
Second Phases

The effect of Ca and Sr content on the microstructure and mechanical properties of a cast AZ91 magnesium alloy is investigated. Ca and Sr additions in AZ91 magnesium alloy are expected high creep resistance. The microstructure of the alloy exhibits the dendritic α-matrix and the second-phases forming networks on the grain boundary. Tensile tests at elevated temperatures between 448 and 523K reveal that the creep resistance was improved with increasing the additional amount of Ca, especially more than 1.0wt%. From the perspective of grain refinement effect, it is expected that the additions of Ca and Sr to AZ91 magnesium alloy not only improve creep resistance but also improve mechanical properties at room temperature.

Micro pulling down growth of very thin shape memory alloys single crystals

2017 ◽  
Vol 10 (01) ◽  
pp. 1740003 ◽  
Author(s):  
I. López-Ferreño ◽  
J. San Juan ◽  
T. Breczewski ◽  
G. A. López ◽  
M. L. Nó
Keyword(s):  
Mechanical Properties ◽  
Shape Memory Alloys ◽  
Single Crystal ◽  
Shape Memory ◽  
Single Crystals ◽  
Functional Materials ◽  
Small Scale ◽  
Cylindrical Shape ◽  
Minimum Diameter ◽  
Wide Range

Shape memory alloys (SMAs) have attracted much attention in the last decades due to their thermo-mechanical properties such as superelasticity and shape memory effect. Among the different families of SMAs, Cu–Al–Ni alloys exhibit these properties in a wide range of temperatures including the temperature range of 100–200[Formula: see text]C, where there is a technological demand of these functional materials, and exhibit excellent behavior at small scale making them more competitive for applications in Micro Electro-Mechanical Systems (MEMS). However, polycrystalline alloys of Cu-based SMAs are very brittle so that they show their best thermo-mechanical properties in single-crystal state. Nowadays, conventional Bridgman and Czochralski methods are being applied to elaborate single-crystal rods up to a minimum diameter of 1[Formula: see text]mm, but no works have been reported for smaller diameters. With the aim of synthesizing very thin single-crystals, the Micro-Pulling Down ([Formula: see text]-PD) technique has been applied, for which the capillarity and surface tension between crucible and the melt play a critical role. The [Formula: see text]-PD method has been successfully applied to elaborate several cylindrical shape thin single-crystals down to 200[Formula: see text][Formula: see text]m in diameter. Finally, the martensitic transformation, which is responsible for the shape memory properties of these alloys, has been characterized for different single-crystals. The experimental results evidence the good quality of the grown single-crystals.

scholarly journals The Microstructure, Mechanical Properties and Coatability of Diffusion Brazed CMSX-4 Single Crystal

1996 ◽  
Author(s):  
Warren M. Miglietti ◽  
Ros C. Pennefather
Keyword(s):  
Mechanical Properties ◽  
Single Crystal ◽  
Elevated Temperatures ◽  
Aluminide Coating ◽  
Turbine Blades ◽  
Stress Rupture ◽  
Directionally Solidified ◽  
Diffusion Brazing ◽  
Brazed Joints ◽  
Boride Phases

Diffusion brazing is a joining process utilized both in the manufacture and repair of turbine blades and vanes. CMSX-4 is an investment cast, single crystal, Ni-based superalloy used for turbine blading and vanes, and has enhanced mechanical properties at elevated temperatures when compared to equiaxed, directionally solidified and first generation single crystal superalloys. The objective of this work was to develop a diffusion brazing procedure to achieve reliable joints in the manufacture of a hollow turbine blade (for a prototype engine in South Africa), and to verify the coatability of the diffusion brazed joints. Two commercially available brazing filler metals of composition Ni-15Cr-3.5B and Ni-7Cr-3Fe-4.5Si-3.2B-0.06C and a proprietary (wide gap) braze were utilized. With the aim of eliminating brittle centre-line boride phases, the effects of temperature and time on the joint microstructure were studied. Once the metallurgy of the joint was understood, tensile and stress rupture tests were undertaken, the latter being one of the severest tests to evaluate joint strength. The results demonstrated that the diffusion brazed joints could satisfy the specified stress rupture criterion of a minimum of 40 hrs life at 925 °C and 200 MPa. After mechanical property evaluations, an investigation into the effects of a low temperature high activity (LTHA) pack aluminide coating and a high temperature low activity (HTLA) pack aluminide coating on the braze joints was undertaken. The results showed that diffusion brazed joints could be readily coated.

Compressive Plasticity of Zr-Based Bulk Metallic Glass at Low Temperature

2012 ◽  
Vol 443-444 ◽  
pp. 583-586
Author(s):  
Ya Juan Sun ◽  
Ri Ga Wu ◽  
Hong Jing Wang
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Metallic Glass ◽  
Bulk Metallic Glass ◽  
Low Temperatures ◽  
Room Temperature ◽  
Shear Bands ◽  
Strain Curve ◽  
Testing Temperature ◽  
Stress Strain Curve

The mechanical properties of a new Zr-based bulk metallic glass at low temperatures were investigated. The results indicate that the fracture strength increases significantly (4.9%) and the global plasticity increases somewhat when testing temperature is lowered to 123K. The stress-strain curve of the sample deformed exhibits more serrations and smaller stress drop due to formation of more shear bands at low temperature than at room temperature.

An Experimental Study of Carbon Nanotube Reinforcements

2011 ◽  
Author(s):  
Lauren Patrin ◽  
Frank Chow ◽  
Gabriela Philippart ◽  
Feridun Delale ◽  
Benjamin Liaw ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Young's Modulus ◽  
Testing Machine ◽  
Type I ◽  
Electrical Measurements ◽  
Standard Type ◽  
Reinforcement Percentage

Due to their high strength and stiffness carbon nanotubes (CNTs) have been considered as candidates for reinforcement of polymeric resins. It is also known that the addition of CNTs to polymeric matrix results in highly conductive nanocomposites, making the material multifunctional. Most of the CNT reinforced polymeric nanocomposite systems reported in the literature have been studied at room temperature. However, in many applications, materials may be subjected from low to elevated temperatures. Thus, the aim of this research is to study CNT reinforced polypropylene (PP) specimens at room, elevated and low temperatures. ASTM standard Type I specimens manufactured via injection molding and reinforced with 0.2%, 1%, 3%, and 6% CNTs were first subjected to tensile loads in a universal testing machine at room temperature. Neat PP resin specimens were also tested to provide baseline data. The tests were repeated at −54°C (−65°F), −20°C (−4°F), 49°C (120°F) and 71°C (160°F). The results were plotted as stress-strain curves and analyzed to delineate the effect of CNT reinforcement percentage and temperature on the mechanical properties. It was noted that as the percentage of CNT reinforcement increases, the resulting nanocomposite becomes stiffer (higher Young’s modulus), has higher strength and becomes more brittle. Temperature has a drastic effect on the behavior of the nanocomposite. As the temperature increases, at a given reinforcement percentage the material becomes more ductile with significantly lower Young’s modulus and strength compared to room temperature. At lower temperatures, the nanocomposite becomes more brittle with higher stiffness and strength, but significantly reduced failure strain. Also electrical measurements were conducted on the specimens to measure their resistance. For specimens reinforced with up to 3% of CNTs no electrical conductivity was detected. As expected at 6% CNT reinforcement (which is above the approximately 4% percolation limit reported in the literature), the specimens became electrically conductive. To predict the mechanical properties obtained experimentally, a micromechanics based model is presented and compared with the experimental results.

Experimental Study on the Mechanical Property and Forming Limit of Magnesium Sheet at Elevated Temperatures

2009 ◽  
Author(s):  
Y. Huang ◽  
J. Huang ◽  
J. Cao
Keyword(s):  
Elevated Temperature ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Strain Curve ◽  
Tensile Tests ◽  
Alloy Sheet ◽  
Dome Height ◽  
Forming Limit ◽  
Uniaxial Tensile ◽  
Magnesium Sheet

Magnesium alloy sheet has received increasing attention in automotive and aerospace industries. It is widely recognized that magnesium sheet has a poor formability at room temperature. While at elevated temperature, its formability can be dramatically improved. Most of work in the field has been working with the magnesium sheet after annealed around 350°C. In this paper, the as-received commercial magnesium sheet (AZ31B-H24) with thickness of 2mm has been experimentally studied without any special heat treatment. Uniaxial tensile tests at room temperature and elevated temperature were first conducted to have a better understanding of the material properties of magnesium sheet (AZ31B-H24). Then, limit dome height (LDH) tests were conducted to capture forming limits of magnesium sheet (AZ31B-H24) at elevated temperatures. An optical method has been introduced to obtain the stress-strain curve at elevated temperatures. Experimental results of the LDH tests were presented.

scholarly journals Mechanical Properties of Steels for Cold-Formed Steel Structures at Elevated Temperatures

2020 ◽  
Vol 2020 ◽  
pp. 1-18
Author(s):  
Zhen Nie ◽  
Yuanqi Li ◽  
Yehua Wang
Keyword(s):  
Mechanical Properties ◽  
Material Properties ◽  
Elevated Temperatures ◽  
Elasticity Modulus ◽  
Mechanical Performance ◽  
Strain Curve ◽  
Steel Structures ◽  
Test Method ◽  
Stress Relieving ◽  
Cold Formed Steel

It is highly important to clarify the high-temperature mechanical properties in the design of cold-formed steel (CFS) structures under fire conditions due to the unique deterioration feature in material properties under fire environment and associated reduction to the mechanical performance of members. This paper presents the mechanical properties of widely used steels for cold-formed steel structures at elevated temperatures. The coupons were extracted from original coils of proposed full annealed steels (S350 and S420, with nominal yielding strengths 280 MPa and 350 MPa) and proposed stress relieving annealed steels (G500, with nominal yielding strength 500 MPa) for CFS structures with thickness of 1.0 mm and 1.2 mm, and a total of nearly 50 tensile tests were carried out by steady-state test method for temperatures ranging from 20 to 700°C. Based on the tests, material properties including the yield strengths, ultimate strengths, the elasticity modulus, and the stress-strain curve were obtained. Meanwhile, the ductility of steels for CFS structures was discussed. Then, the temperature-dependent retention factors of yield strengths and elasticity modulus were compared to those provided by design codes and former researchers. Finally, a set of prediction equations of the mechanical properties for steels for CFS structures at elevated temperatures was proposed depending on existing tests data.

Sign in / Sign up

Export Citation Format

Share Document