The effects of biochar on the physical properties of bare soil

2012 ◽  
Vol 103 (1) ◽  
pp. 5-11 ◽  
Author(s):  
Francesca Ventura ◽  
Fiorenzo Salvatorelli ◽  
Stefano Piana ◽  
Linda Pieri ◽  
Paola Rossi Pisa
Keyword(s):  
Soil Moisture ◽  
Bulk Density ◽  
Soil Water ◽  
Agricultural Soil ◽  
Water Retention ◽  
Bare Soil ◽  
Soil Water Retention ◽  
Experimental Scheme ◽  
Dark Colour ◽  
Key Factor

ABSTRACTThe pyrolysis conversion of vegetable residues into energy and biochar, and its incorporation in agricultural soil, reduces CO2emission and provides a longterm soil carbon sequestration. Moreover, biochar application in soil seems to increase nutrient stocks in the rooting layer, improving crop yield. Compared with the numerous studies assessing the positive effect of biochar on yield, however, little research has been published elucidating the mechanisms responsible for the reported benefits. Few studies cited soil moisture as the key factor, attributing the increased yield to the higher soil water availability.The aim of this study was to investigate the effect of biochar on the physical and hydraulic properties of a bare Padana Plain (Cadriano, Bologna) agricultural soil. A preliminary plot experiment in 2009 explored the influence of 10 and 30 kg ha–1of biochar on soil moisture, without effects from plants. Results of the first experiment suggested using higher biochar rates in a similar experimental scheme. During the second experiment, 30 and 60 t ha–1doses were investigated. Soil water content, bulk density, electrical conductivity and soil water retention were measured. The comparison between treated soils and the control indicates that the biochar rate is directly correlated to electrical conductibility and inversely correlated with bulk density. The effect on the density of soil can be very positive in case of heavy soils. The dark colour of the char increased the surface temperature with respect to the control, while no differences were detected at 7·5 cm depth. No influences were found on other soil characteristics, including soil pH, moisture and water retention.

scholarly journals The Relationship between Soil Moisture and LAI in Different Types of Soil in Central Eastern China

2016 ◽  
Vol 17 (11) ◽  
pp. 2733-2742 ◽  
Author(s):  
Li Liu ◽  
Renhe Zhang ◽  
Zhiyan Zuo
Keyword(s):  
Particle Size ◽  
Soil Moisture ◽  
Soil Water ◽  
Water Retention ◽  
Eastern China ◽  
Soil Water Retention ◽  
Different Types ◽  
Central Eastern ◽  
The Impact ◽  
The Relationship

Abstract As important parameters in the land–atmosphere system, both soil moisture (SM) and vegetation play a significant role in land–atmosphere interactions. Using observational data from clay and sand stations over central eastern China, the relationship between leaf area index (LAI) and SM (LAI–SM) in different types of soil was investigated. The results show that the LAI–SM correlation is significantly positive in clay but not significant in sand. The physical causes for the discrepant LAI–SM correlations in different types of soil were explored from the perspectives of evapotranspiration (ET) and soil water retention. In clay stations, increasing LAI is associated with greater soil-water-retention capacity. Although the increasing LAI corresponds to increasing ET, the impact of ET on SM is weak because of the small particle size of soil. Consequently, the LAI–SM relationship in clay is significantly positive. In sand stations, ET is negatively correlated with SM owing to the large soil particle size, resulting in a negative LAI–SM correlation in sand. However, soil water retention is weakened by the increased LAI, which may be an important factor causing the insignificant LAI–SM correlation in sand.

Soil Physical Properties of Tied Ridges in the Sudan Savannah of Burkina Faso

1988 ◽  
Vol 24 (3) ◽  
pp. 375-384 ◽  
Author(s):  
N. R. Hulugalle ◽  
M. S. Rodriguez
Keyword(s):  
Physical Properties ◽  
Soil Temperature ◽  
Bulk Density ◽  
Soil Water ◽  
Water Retention ◽  
Clay Content ◽  
Soil Physical Properties ◽  
Water Infiltration ◽  
Soil Water Retention ◽  
Maize Varieties

SUMMARYThe soil physical properties of tied ridges were measured in a trial, established in 1983, comparing three treatments: handhoe cultivation and planting on the flat; planting directly without any cultivation on tied ridges constructed the previous year; and handhoe cultivation and remoulding of tied ridges constructed the previous year. Two maize varieties and two management levels were used. The soil properties monitored were particle size distribution, penetro-meter resistance in the surface 20 mm, bulk density, water infiltration, soil water retention and soil temperature.Soil physical properties were affected mainly by the type of seedbed. Clay content in the surface 0.05 m was greater with tied ridging, with that in the furrows being higher than that in the ridge slopes. Daily maximum soil temperature was greatest in the flat planted plots and in the ridge slopes of the tied ridged plots. Penetrometer resistance at a soil water content of 0.05 kg kg−1 was greater in the tied ridged plots. Cumulative infiltration after 2 h was greatest with flat planting. The bulk density of ridge slopes in tied ridged plots was less than that in the furrows and in the flat planted plots. Soil water retention was greatest in the furrows of the tied ridged plots. Clay content was the major factor determining all the soil physical properties measured.

scholarly journals Soil Water, NH4, and NO3 Retention in Low-maintenance Annual Landscape Beds Amended with a Hydophilic Polymer

HortScience ◽  
1995 ◽  
Vol 30 (4) ◽  
pp. 896D-896 ◽  
Author(s):  
Jennifer L. Boatright ◽  
J.M. Zajicek ◽  
W.A. Mackay
Keyword(s):  
Soil Moisture ◽  
Plant Growth ◽  
Soil Water ◽  
Water Retention ◽  
Polyacrylamide Gel ◽  
Soil Water Retention ◽  
Drain Pipe

Two experiments were conducted in which a polyacrylamide gel (Hydrosource, Western Polyacrylamide) was incorporated into 56 × 38-cm, raised, concrete beds, 20 cm deep, with a drain pipe in the center of each bed. In Expt. 1, treatments included (in grams of i.a. N) 0, 186, 372, or 558 plus 0 or 366 g hydrogel/m2, for a total of eight treatments. Each treatment was replicated three times. Petunia plants were transplanted into each plot for a total of 30 plants per treatment. Plants were kept well watered. Polymer incorporation had no effect on soil water retention, soil NO3 or NH4 retention, or plant growth. Expt. 2 included treatments of 0 or 186 g of ai N and 0 or 366 g hydrogel/m2. Each treatment was replicated six times with 10 plants per replication, resulting in a total of 60 plants per treatment. Minimal irrigation was imposed on treatments. This study demonstrated that under suboptimal conditions of minimal irrigation and fertilization, polymer incorporation significantly increased soil moisture (17%), NH4 retention (83%), and NO3 retention where additional N was added (64%) compared to soils without polymer.

scholarly journals The Influence of a Water Absorbing Geocomposite on Soil Water Retention and Soil Matric Potential

Water ◽  
2019 ◽  
Vol 11 (8) ◽  
pp. 1731 ◽  
Author(s):  
Michał Śpitalniak ◽  
Krzysztof Lejcuś ◽  
Jolanta Dąbrowska ◽  
Daniel Garlikowski ◽  
Adam Bogacz
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Soil Water ◽  
Water Retention ◽  
Soil Moisture Content ◽  
Soil Surface ◽  
Soil Matric Potential ◽  
Soil Water Retention ◽  
Matric Potential ◽  
Control Samples

Climate change induces droughts that are becoming more intensive and more frequent than ever before. Most of the available forecast tools predict a further significant increase in the risk of drought, which indicates the need to prepare solutions to mitigate its effects. Growing water scarcity is now one of the world’s leading challenges. In agriculture and environmental engineering, in order to increase soil water retention, soil additives are used. In this study, the influence of a newly developed water absorbing geocomposite (WAG) on soil water retention and soil matric potential was analyzed. WAG is a special element made from geotextile which is wrapped around a synthetic skeleton with a superabsorbent polymer placed inside. To describe WAG’s influence on soil water retention and soil matric potential, coarse sand, loamy sand, and sandy loam soils were used. WAG in the form of a mat was used in the study as a treatment. Three kinds of samples were prepared for every soil type. Control samples and samples with WAG treatment placed at depths of 10 cm and 20 cm were examined in a test container of 105 × 70 × 50 cm dimensions. The samples had been watered and drained, and afterwards, the soil surface was heated by lamps of 1100 W total power constantly for 72 h. Soil matric potential was measured by Irrometer field tensiometers at three depths. Soil moisture content was recorded at six depths: of 5, 9, 15, 19, 25, and 30 cm under the top of the soil surface with time-domain reflectometry (TDR) measurement devices. The values of soil moisture content and soil matric potential were collected in one-minute steps, and analyzed in 24-h-long time steps: 24, 48, and 72 h. The samples with the WAG treatment lost more water than the control samples. Similarly, lower soil matric potential was noted in the samples with the WAG than in the control samples. However, after taking into account the water retained in the WAG, it appeared that the samples with the WAG had more water easily available for plants than the control samples. It was found that the mechanism of a capillary barrier affected higher water loss from soil layers above those where the WAG had been placed. The obtained results of water loss depend on the soil type used in the profile.

scholarly journals Estimated soil water storage within a historical bunker during the growth period of vegetation

2018 ◽  
Vol 39 (1) ◽  
pp. 125-130 ◽  
Author(s):  
Łukasz Pardela ◽  
Tomasz Kowalczyk
Keyword(s):  
Soil Moisture ◽  
Soil Water ◽  
Water Retention ◽  
Growth Period ◽  
Vegetation Period ◽  
Soil Water Storage ◽  
Soil Profiles ◽  
Soil Water Retention ◽  
Average Value ◽  
Volumetric Soil Moisture

AbstractThe objective of the study was to estimate the variation of soil water retention on the site of a historical bunker, an element of the former Wrocław Fortress in Poland. Measurements of soil moisture in the study area were taken in the period from March to September, 2017. Measurements of volumetric soil moisture were taken by means of a hand-held gauge, type FOM/mts with an FP/mts probe, operating on the basis of the reflectometric technique TDR. Soil moisture measurements realized in the vegetation period demonstrated that soil moisture resources in profiles situated in the section of the bunker varied within the range of 37–135 mm in the layer of 50 cm, and 66–203 mm in the layer of 100 cm. The maximum differences of the average value of soil moisture of the soil profiles studied in the period covered by the measurements were 31 mm and 56 mm, respectively. This indicates a significant differentiation of the retention properties of soils used for the construction of individual shelter areas.

Relating soil structure and hydrophysical characteristics to aerobic and anaerobic soil respiration

2020 ◽  
Author(s):  
Teamrat Ghezzehei ◽  
Jennifer Alvarez ◽  
Yocelyn Villa ◽  
Rebecca Ryals
Keyword(s):  
Organic Matter ◽  
Soil Moisture ◽  
Soil Water ◽  
Soil Structure ◽  
Water Retention ◽  
Water Retention Curve ◽  
Soil Water Retention Curve ◽  
Soil Water Retention ◽  
Retention Curve ◽  
Aerobic And Anaerobic

<p>The dynamics of soil organic matter is strongly controlled by the hydrophysical environmental factors, including motility, aqueous diffusivity of substrates, gaseous diffusivity, and energetic constraints on microbial physiology. The relationships among these physical factors depend on soil moisture and the architecture of the soil pores. In this regard, the soil water retention curve can serve as a macroscopic signature of pore-size distribution. Therefore, the sensitivity of aerobic and anaerobic microbial activity must be closely associated with the shape of the soil water retention curve. The soil water retention curve is, in turn, strongly dependent on soil texture and structure. Here, we present a physically-based model of aerobic and anaerobic microbial respiration rates. We also present a novel experimental technique for the characterization of the soil-moisture sensitivity of soil microbial activity. The proposed experimental and modeling approaches allow direct coupling of the fate soil organic matter with the nature of soil structure.</p>

scholarly journals Estimating soil water retention for wide ranges of pressure head and bulk density based on a fractional bulk density concept

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Huihui Sun ◽  
Jaehoon Lee ◽  
Xijuan Chen ◽  
Jie Zhuang
Keyword(s):  
Water Content ◽  
Bulk Density ◽  
Soil Water ◽  
Water Retention ◽  
Pore Space ◽  
Pressure Head ◽  
Soil Bulk Density ◽  
Residual Water ◽  
Soil Water Retention ◽  
Residual Water Content

Abstract Soil water retention determines plant water availability and contaminant transport processes in the subsurface environment. However, it is usually difficult to measure soil water retention characteristics. In this study, an analytical model based on a fractional bulk density (FBD) concept was presented for estimating soil water retention curves. The concept allows partitioning of soil pore space according to the relative contribution of certain size fractions of particles to the change in total pore space. The input parameters of the model are particle size distribution (PSD), bulk density, and residual water content at water pressure head of 15,000 cm. The model was tested on 30 sets of water retention data obtained from various types of soils that cover wide ranges of soil texture from clay to sand and soil bulk density from 0.33 g/cm3 to 1.65 g/cm3. Results showed that the FBD model was effective for all soil textures and bulk densities. The estimation was more sensitive to the changes in soil bulk density and residual water content than PSD parameters. The proposed model provides an easy way to evaluate the impacts of soil bulk density on water conservation in soils that are manipulated by mechanical operation.

scholarly journals Estimating Soil Water Retention Curve by Inverse Modelling from Combination of In Situ Dynamic Soil Water Content and Soil Potential Data

Soil Systems ◽  
2018 ◽  
Vol 2 (4) ◽  
pp. 55 ◽  
Author(s):  
Pinnara Ket ◽  
Chantha Oeurng ◽  
Aurore Degré
Keyword(s):  
Soil Moisture ◽  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Water Retention ◽  
Inverse Modelling ◽  
Soil Water Retention ◽  
Moisture Dynamics ◽  
Hydrus 1D

Soil water retention curves (SWRCs) are crucial for characterizing soil moisture dynamics, and are particularly relevant in the context of irrigation management. Inverse modelling is one of the methods used to parameterize models representing these curves, which are closest to the field reality. The objective of this study is to estimate the soil hydraulic properties through inverse modelling using the HYDRUS-1D code based on soil moisture and potential data acquired in the field. The in situ SWRCs acquired every 30 min are based on simultaneous soil water content and soil water potential measurements with 10HS and MPS-2 sensors, respectively, in five experimental fields. The fields were planted with drip-irrigated lettuces from February to March 2016 in the Chrey Bak catchment located in the Tonlé Sap Lake region, Cambodia. After calibration of the van Genuchten soil water retention model parameters, we used them to evaluate the performance of HYDRUS-1D to predict soil moisture dynamics in the studied fields. Water flow was reasonably well reproduced in all sites covering a range of soil types (loamy sand and loamy soil) with root mean square errors ranging from 0.02 to 0.03 cm3 cm−3.

Sign in / Sign up

Export Citation Format

Share Document