Simultaneous Optimization of Adsorption Capacity and Stability of Hydrothermally Synthesized Spinel Ion Sieve Composite Adsorbents for Selective Removal of Lithium from Aqueous Solutions

2019 ◽  
Vol 58 (27) ◽  
pp. 12207-12215 ◽  
Author(s):  
Majid Bazrgar Bajestani ◽  
Ahmad Moheb ◽  
Mohammadali Masigol
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Selective Removal ◽  
Simultaneous Optimization ◽  
Composite Adsorbents

Sorption of Bisphenol A in Aqueous Solutions on Irradiated and as-Grown Multiwalled Carbon Nanotubes

2018 ◽  
Vol 69 (5) ◽  
pp. 1233-1239
Author(s):  
Raluca Madalina Senin ◽  
Ion Ion ◽  
Ovidiu Oprea ◽  
Rusandica Stoica ◽  
Rodica Ganea ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Bisphenol A ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Multiwalled Carbon Nanotubes ◽  
Adsorption Process ◽  
Sorption Process ◽  
Multiwalled Carbon ◽  
Before And After ◽  
Kinetic Sorption

In this study, non-irradiated and weathered multiwalled carbon nanotubes (MWCNTs) obtained through irradiation, were studied as adsorbents for BPA, both nanomaterials being characterized before and after the adsorption process. The objectives of our investigation were to compare the characteristics of non-irradiated and irradiated MWCNTs, to evaluate the adsorption capacity of BPA by pristine and irradiated MWCNTs and to determine the variation of the kinetic, sorption and thermodynamic parameters during sorption process using both sorbents.

scholarly journals Enhanced Adsorption of Bisphenol A from Aqueous Solution with 2-Vinylpyridine Functionalized Magnetic Nanoparticles

Polymers ◽  
2018 ◽  
Vol 10 (10) ◽  
pp. 1136 ◽  
Author(s):  
Qiang Li ◽  
Fei Pan ◽  
Wentao Li ◽  
Dongya Li ◽  
Haiming Xu ◽  
...  
Keyword(s):  
Bisphenol A ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Magnetic Nanoparticle ◽  
Maximum Adsorption Capacity ◽  
Salting Out ◽  
Functionalized Magnetic Nanoparticles ◽  
Ft Ir ◽  
Fe3o4 Nanospheres ◽  
Enhanced Adsorption

In this study, a novel 2-vinylpyridine functionalized magnetic nanoparticle (Mag-PVP) was successfully prepared. The prepared Mag-PVP was characterized by transmission electronic microscopy (TEM), Fourier transform infrared spectrophotometry (FT-IR), vibrating sample magnetometry (VSM) and thermogravimetric analysis (TGA), and was used for the adsorption of bisphenol A (BPA) from aqueous solutions. Mag-PVP, which is composed of Fe3O4 nanoparticles and poly divinylbenzene-2-vinylpyridine (with a thickness of 10 nm), exhibited magnetic properties (Ms = 44.6 emu/g) and thermal stability. The maximum adsorption capacity (Qm) of Mag-PVP for BPA obtained from the Langmuir isotherm was 115.87 mg/g at 20 °C, which was more than that of Fe3O4 nanospheres. In the presence of NaCl, the improved adsorption capacity of Mag-PVP was probably attributed to the screening effect of Mag-PVP surface charge and salting-out effect. In the presence of CaCl2 and humic acid (HA), the adsorption capacity of BPA decreased due to competitive adsorption. The adsorption of BPA by Mag-PVP increased slightly with the increase in pH from 3.0 to 5.0 and obtained the largest adsorption amount at pH 5.0, which was probably attributed to hydrogen bonding interactions. Moreover, in actual water, Mag-PVP still showed excellent adsorption performance in removing BPA. The high adsorption capacity and excellent reusability performance in this work indicated that Mag-PVP was an effective adsorbent for removing BPA from aqueous solutions.

scholarly journals Magnetically Recyclable Wool Keratin Modified Magnetite Powders for Efficient Removal of Cu2+ Ions from Aqueous Solutions

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1068
Author(s):  
Xinyue Zhang ◽  
Yani Guo ◽  
Wenjun Li ◽  
Jinyuan Zhang ◽  
Hailiang Wu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Ion Concentration ◽  
Bet Surface Area ◽  
Chemical Compositions ◽  
Ion Adsorption ◽  
X Ray ◽  
Wool Keratin

The treatment of wastewater containing heavy metals and the utilization of wool waste are very important for the sustainable development of textile mills. In this study, the wool keratin modified magnetite (Fe3O4) powders were fabricated by using wool waste via a co-precipitation technique for removal of Cu2+ ions from aqueous solutions. The morphology, chemical compositions, crystal structure, microstructure, magnetism properties, organic content, and specific surface area of as-fabricated powders were systematically characterized by various techniques including field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometer (VSM), thermogravimetric (TG) analysis, and Brunauer–Emmett–Teller (BET) surface area analyzer. The effects of experimental parameters such as the volume of wool keratin hydrolysate, the dosage of powder, the initial Cu2+ ion concentration, and the pH value of solution on the adsorption capacity of Cu2+ ions by the powders were examined. The experimental results indicated that the Cu2+ ion adsorption performance of the wool keratin modified Fe3O4 powders exhibited much better than that of the chitosan modified ones with a maximum Cu2+ adsorption capacity of 27.4 mg/g under favorable conditions (0.05 g powders; 50 mL of 40 mg/L CuSO4; pH 5; temperature 293 K). The high adsorption capacity towards Cu2+ ions on the wool keratin modified Fe3O4 powders was primarily because of the strong surface complexation of –COOH and –NH2 functional groups of wool keratins with Cu2+ ions. The Cu2+ ion adsorption process on the wool keratin modified Fe3O4 powders followed the Temkin adsorption isotherm model and the intraparticle diffusion and pseudo-second-order adsorption kinetic models. After Cu2+ ion removal, the wool keratin modified Fe3O4 powders were easily separated using a magnet from aqueous solution and efficiently regenerated using 0.5 M ethylene diamine tetraacetic acid (EDTA)-H2SO4 eluting. The wool keratin modified Fe3O4 powders possessed good regenerative performance after five cycles. This study provided a feasible way to utilize waste wool textiles for preparing magnetic biomass-based adsorbents for the removal of heavy metal ions from aqueous solutions.

Fabrication of monodisperse polypyrrole/SBA-15 composite for the selective removal of Cr(Ⅵ) from aqueous solutions

2021 ◽  
Author(s):  
Liang Wang ◽  
Peng Gao ◽  
Mengxin Liu ◽  
Ziqing Huang ◽  
Shixia Lan ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Aqueous Solutions ◽  
Adsorption Process ◽  
In Situ Polymerization ◽  
Selective Removal ◽  
Factors Affecting

Monodisperse polypyrrole/SBA-15 composite (PPy/SBA-15) was fabricated by in-situ polymerization and used for Cr(Ⅵ) adsorption from aqueous solution. PPy/SBA-15 was characterized by numerous approaches. Factors affecting the Cr(Ⅵ) adsorption process included...

scholarly journals Selective removal of lead ions from aqueous solutions using SiO2–MoO3: Isotherm, kinetics and thermodynamic studies

2021 ◽  
Vol 3 ◽  
pp. 100083
Author(s):  
Jasmina Sulejmanović ◽  
Neira Kovač ◽  
Mustafa Memić ◽  
Elma Šabanović ◽  
Sabina Begić ◽  
...  
Keyword(s):  
Aqueous Solutions ◽  
Selective Removal ◽  
Lead Ions ◽  
Thermodynamic Studies ◽  
Kinetics And Thermodynamic

scholarly journals Fabrication of Carboxymethylcellulose/Metal-Organic Framework Beads for Removal of Pb(II) from Aqueous Solution

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 942 ◽  
Author(s):  
Huo-Xi Jin ◽  
Hong Xu ◽  
Nan Wang ◽  
Li-Ye Yang ◽  
Yang-Guang Wang ◽  
...  
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Photoelectron Spectroscopy ◽  
Langmuir Isotherm ◽  
Adsorption Equilibrium ◽  
Isotherm Model ◽  
Maximum Adsorption Capacity ◽  
X Ray ◽  
Metal Organic ◽  
Langmuir Isotherm Model

The ability to remove toxic heavy metals, such as Pb(II), from the environment is an important objective from both human-health and ecological perspectives. Herein, we describe the fabrication of a novel carboxymethylcellulose-coated metal organic material (MOF-5–CMC) adsorbent that removed lead ions from aqueous solutions. The adsorption material was characterized by Fourier-transform infrared spectroscopy, X-ray diffractometry, scanning electron microscopy, and X-ray photoelectron spectroscopy. We studied the functions of the contact time, pH, the original concentration of the Pb(II) solution, and adsorption temperature on adsorption capacity. MOF-5–CMC beads exhibit good adsorption performance; the maximum adsorption capacity obtained from the Langmuir isotherm-model is 322.58 mg/g, and the adsorption equilibrium was reached in 120 min at a concentration of 300 mg/L. The adsorption kinetics is well described by pseudo-second-order kinetics, and the adsorption equilibrium data are well fitted to the Langmuir isotherm model (R2 = 0.988). Thermodynamics experiments indicate that the adsorption process is both spontaneous and endothermic. In addition, the adsorbent is reusable. We conclude that MOF-5–CMC is a good adsorbent that can be used to remove Pb(II) from aqueous solutions.

Ouricuri (Syagrus coronata) fiber: a novel biosorbent to remove methylene blue from aqueous solutions

2016 ◽  
Vol 75 (1) ◽  
pp. 106-114 ◽  
Author(s):  
Lucas Meili ◽  
Társila Santos da Silva ◽  
Daniely Carlos Henrique ◽  
João Inácio Soletti ◽  
Sandra Helena Vieira de Carvalho ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Experimental Design ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Adsorption Process ◽  
Fiber Diameter ◽  
Aqueous Media ◽  
Process Efficiency ◽  
Maximum Adsorption Capacity ◽  
Equilibrium Studies

In this work, the potential of ouricuri (Syagrus coronata) fiber as a novel biosorbent to remove methylene blue (MB) from aqueous solutions was investigated. The fiber was prepared and characterized according to the fundamental features for adsorption. A 23 experimental design was used to evaluate the effects of adsorbent dosage (M), fiber diameter (D) and agitation (A) on the adsorption capacity. In the more adequate conditions, kinetic and equilibrium studies were performed. The experimental design results showed that M = 10 g L−1), D = 0.595 mm and A = 200 rpm were the more adequate conditions for MB adsorption. Based on the kinetic study, it was found that the adsorption process was fast, being the equilibrium was attained at about 5 min, with 90% of color removal. The isotherm was properly represented by the Sips model, and the maximum adsorption capacity was 31.7 mg g−1. In brief, it was demonstrated that ouricuri fiber is an alternative biosorbent to remove MB from aqueous media, taking into account the process efficiency and economic viewpoint.

Sign in / Sign up

Export Citation Format

Share Document