scholarly journals The impact of focused ion beam induced damage on scanning spreading resistance microscopy measurements

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Komal Pandey ◽  
Kristof Paredis ◽  
Thomas Hantschel ◽  
Chris Drijbooms ◽  
Wilfried Vandervorst
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Three Dimensional ◽  
Region Of Interest ◽  
Amorphous Region ◽  
Impact Angle ◽  
Spreading Resistance ◽  
Energy Impact ◽  
The Impact ◽  
Dopant Deactivation

Abstract Scanning Spreading Resistance Microscopy is a well-established technique for obtaining quantitative two- and three-dimensional carrier profiles in semiconductor devices with sub-nm spatial resolution. However, for sub-100 nm devices, the use of focused ion beam becomes inevitable for exposing the region of interest on a sample cross section. In this work, we investigate the impact of the focused ion beam milling on spreading resistance analysis and we show that the electrical effect of the focused ion beam extends far beyond the amorphous region and depends on the dopant concentration, ion beam energy, impact angle, and current density. For example, for dopant concentrations between 1.0 × 1020 and 1.5 × 1016 cm−3 we observe dopant deactivation at least between 23 and 175 nm for a glancing 30 keV ion beam. Further, we show that dopant deactivation is caused by defect diffusion during milling and is not directly impacted by the presence of Gallium in the sample. Later, we also discuss potential ways to mitigate these effects.

scholarly journals Thin Solid Film Electrolyte and Its Impact on Electrode Polarization in Solid Oxide Fuel Cells Studied by Three-Dimensional Microstructure-Scale Numerical Simulation

Energies ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 5127
Author(s):  
Tomasz A. Prokop ◽  
Grzegorz Brus ◽  
Shinji Kimijima ◽  
Janusz S. Szmyd
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Three Dimensional ◽  
Reaction Rates ◽  
Solid Oxide ◽  
Scale Model ◽  
Electrode Polarization ◽  
Computational Domain ◽  
Oxide Fuel ◽  
The Impact

In this work, a three-dimensional microstructure-scale model of a Solid Oxide Fuel Cell’s Positive-Electrolyte-Negative assembly is applied for the purpose of investigating the impact of decreasing the electrolyte thickness on the magnitude, and the composition of electrochemical losses generated within the cell. Focused-Ion-Beam Scanning Electron Microscopy reconstructions are used to construct a computational domain, in which charge transport equations are solved. Butler–Volmer model is used to compute local reaction rates, and empirical relationships are used to obtain local conductivities. The results point towards three-dimensional nature of transport phenomena in thin electrolytes, and electrode-electrolyte interfaces.

Combined Electron Beam Induced Current Imaging (EBIC) and Focused Ion Beam (FIB) Techniques for Thin Film Solar Cell Characterization

2010 ◽  
Author(s):  
Frank Altmann ◽  
Jan Schischka ◽  
Vinh Van Ngo ◽  
Stacey Stone ◽  
Laurens F. Tz. Kwakman ◽  
...  
Keyword(s):  
Thin Film ◽  
Electron Beam ◽  
Focused Ion Beam ◽  
Surface Defects ◽  
Ion Beam ◽  
Three Dimensional ◽  
Region Of Interest ◽  
Induced Current ◽  
Large Area ◽  
Electron Beam Induced Current

Abstract A novel analytical method applying combined electron beam induced current (EBIC) imaging based on scanning electron microscopy (SEM) and focused ion beam (FIB) cross sectioning in a SEM/FIB dualbeam system is presented. The method is demonstrated in several case studies for process characterization and failure analysis of thin film technology based Solar cells, including Silicon (CSG), Cadmium Telluride (CdTe) and Copper Indium Selenide (CIS) absorbers. While existing techniques such as electro-, photoluminescence spectroscopy and lock-in thermography are able to locate the larger, electrically active defects reasonably fast on a large area, the FIB-SEM EBIC system is uniquely capable of detecting sub-micron, sub-surface defects and of analysing these defects in the same system. In combination with a FIB, the localized region of interest can be easily cross sectioned and additional EBIC analysis can be applied for a three dimensional analysis of the p/n junction.

3D Observation of Elemental Distribution of Si-Device using a Dedicated FIB/STEM System

2005 ◽  
Author(s):  
T. Yaguchi ◽  
M. Konno ◽  
T. Kamino ◽  
M. Ogasawara ◽  
K. Kaji ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Three Dimensional ◽  
Elemental Distribution ◽  
Multivariate Statistical ◽  
X Ray ◽  
Sample Rotation ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Elemental Maps

Abstract A technique for preparation of a pillar shaped sample and its multi-directional observation of the sample using a focused ion beam (FIB) / scanning transmission electron microscopy (STEM) system has been developed. The system employs an FIB/STEM compatible sample rotation holder with a specially designed rotation mechanism, which allows the sample to be rotated 360 degrees [1-3]. This technique was used for the three dimensional (3D) elemental mapping of a contact plug of a Si device in 90 nm technology. A specimen containing a contact plug was shaped to a pillar sample with a cross section of 200 nm x 200 nm and a 5 um length. Elemental analysis was performed with a 200 kV HD-2300 STEM equipped with the EDAX genesis Energy dispersive X-ray spectroscopy (EDX) system. Spectrum imaging combined with multivariate statistical analysis (MSA) [4, 5] was used to enhance the weak X-ray signals of the doped area, which contain a low concentration of As-K. The distributions of elements, especially the dopant As, were successfully enhanced by MSA. The elemental maps were .. reconstructed from the maps.

scholarly journals Investigation of the selective color-changing mechanism of Dynastes tityus beetle (Coleoptera: Scarabaeidae)

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Jiyu Sun ◽  
Wei Wu ◽  
Limei Tian ◽  
Wei Li ◽  
Fang Zhang ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Color Change ◽  
Incidence Angle ◽  
Ion Beam ◽  
Three Dimensional ◽  
Water Infiltration ◽  
Photonic Materials ◽  
Local Color ◽  
Water Contact ◽  
Color Changes

AbstractNot only does the Dynastes tityus beetle display a reversible color change controlled by differences in humidity, but also, the elytron scale can change color from yellow-green to deep-brown in specified shapes. The results obtained by focused ion beam-scanning electron microscopy (FIB-SEM), show that the epicuticle (EPI) is a permeable layer, and the exocuticle (EXO) is a three-dimensional photonic crystal. To investigate the mechanism of the reversible color change, experiments were conducted to determine the water contact angle, surface chemical composition, and optical reflectance, and the reflective spectrum was simulated. The water on the surface began to permeate into the elytron via the surface elemental composition and channels in the EPI. A structural unit (SU) in the EXO allows local color changes in varied shapes. The reflectance of both yellow-green and deep-brown elytra increases as the incidence angle increases from 0° to 60°. The microstructure and changes in the refractive index are the main factors that influence the process of reversible color change. According to the simulation, the lower reflectance causing the color change to deep-brown results from water infiltration, which increases light absorption. Meanwhile, the waxy layer has no effect on the reflection of light. This study lays the foundation to manufacture engineered photonic materials that undergo controllable changes in iridescent color.

scholarly journals Protocol for preparation of heterogeneous biological samples for 3D electron microscopy: a case study for insects

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Alexey A. Polilov ◽  
Anastasia A. Makarova ◽  
Song Pang ◽  
C. Shan Xu ◽  
Harald Hess
Keyword(s):  
Electron Microscopy ◽  
Biological Samples ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Three Dimensional ◽  
Entire Volume ◽  
Simple Protocol ◽  
3D Electron Microscopy ◽  
3D Em

AbstractModern morphological and structural studies are coming to a new level by incorporating the latest methods of three-dimensional electron microscopy (3D-EM). One of the key problems for the wide usage of these methods is posed by difficulties with sample preparation, since the methods work poorly with heterogeneous (consisting of tissues different in structure and in chemical composition) samples and require expensive equipment and usually much time. We have developed a simple protocol allows preparing heterogeneous biological samples suitable for 3D-EM in a laboratory that has a standard supply of equipment and reagents for electron microscopy. This protocol, combined with focused ion-beam scanning electron microscopy, makes it possible to study 3D ultrastructure of complex biological samples, e.g., whole insect heads, over their entire volume at the cellular and subcellular levels. The protocol provides new opportunities for many areas of study, including connectomics.

scholarly journals Site Specific Three-dimensional Structural Analysis in Tissues and Cells Using Automated DualBeam Slice &View

2007 ◽  
Vol 15 (2) ◽  
pp. 26-31 ◽  
Author(s):  
Ben Lich
Keyword(s):  
Electron Microscopy ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Three Dimensional ◽  
Surface Region ◽  
Dimensional Structure ◽  
Near Surface ◽  
Imaging Capability ◽  
Fluorescent Markers ◽  
Confocal And Electron Microscopy

DualBeam instruments that combine the imaging capability of scanning electron microscopy (SEM) with the cutting and deposition capability of a focused ion beam (FIB) provide biologists with a powerful tool for investigating three-dimensional structure with nanoscale (1 nm-100 nm) resolution. Ever since Van Leeuwenhoek used the first microscope to describe bacteria more than 300 years ago, microscopy has played a central role in scientists' efforts to understand biological systems. Light microscopy is generally limited to a useful resolution of about a micrometer. More recently the use of confocal and electron microscopy has enabled investigations at higher resolution. Used with fluorescent markers, confocal microscopy can detect and localize molecular scale features, but its imaging resolution is still limited. SEM is capable of nanometer resolution, but is limited to the near surface region of the sample.

Molding of Three-Dimensional Microcomponents

2006 ◽  
Author(s):  
W. N. P. Hung ◽  
M. M. Agnihotri ◽  
M. Y. Ali ◽  
S. Yuan
Keyword(s):  
Focused Ion Beam ◽  
New Technologies ◽  
Electrical Discharge Machining ◽  
Ion Beam ◽  
Semiconductor Industry ◽  
Three Dimensional ◽  
Cost Effective ◽  
Molecular Structures ◽  
Minimum Size ◽  
Ion Beam Sputtering

Traditional micromanufacturing has been developed for semiconductor industry. Selected micro electrical mechanical systems (MEMS) have been successfully developed and implemented in industry. Since current MEMS are designed for manufacture using microelectronics processes, they are limited to two-dimensional profiles and semiconductor based materials. Such shape and material constraints would exclude many applications that require biocompatibility, dynamic stress, and high ductility. New technologies are sought to fabricate three dimensional microcomponents using robust materials for demanding applications. To be cost effective, such microdevices must be economically mass producible. Molding is one of the promising replication techniques to mass produce components from polymers and polymer-based composites. This paper presents the development of a micromolding process to produce thermoplastic microcomponents. Mold design required precision fitting and was integrated with a vacuum pump to minimize air trap in mold cavities. Nickel and aluminum mold inserts were used for the study; their cavities were fabricated by combinations of available micromachining processes like laser micromachining, micromilling, micro electrical discharge machining, and focused ion beam sputtering. High and low density polyethylene, polystyrene polymers were used for this study. The effects of polymer molecular structures, molding temperature, time, and pressure on molding results were studied. Simulation of stress in the microcomponents, plastic flow in microchannels, and mold defects was performed and compare with experimental data. The research results showed that a microcomponent can be fabricated to the minimum size of 10 ± 1μm (0.0004 inch) with surface roughness <10 nm Rt. Molding of micro-size geartrains and orthopedic meso-size fasteners was completed to illustrate the capability of this process.

Sign in / Sign up

Export Citation Format

Share Document