scholarly journals Research on combustion performance of PVC foam in fire propagation apparatus

2019 ◽  
Vol 118 ◽  
pp. 01034
Author(s):  
Guoan Zhang ◽  
Lingling Wei ◽  
Junhao Gao ◽  
Tingting Qiu ◽  
Rongnan Yuan ◽  
...  
Keyword(s):  
Heat Flux ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
High Speed ◽  
Mass Loss Rate ◽  
Ignition Time ◽  
Combustion Characteristics ◽  
Heat Fluxes ◽  
Fire Propagation

Polyvinyl chloride foam (PVC) is widely used as the wall materials of the high-speed train. The combustion characteristics of PVC foam under the heat fluxes of 20-60 kW/m2 are investigated by fire Propagation Apparatus (FPA). The results show that the ignition time of PVC foam decreases with the increase of heat flux. The peak of heat release rate, mass loss rate and smoke production rate increase with the increase of heat flux. Under the condition of 60 kW/m2, the heat release rate has the peak value of 109.10 kW/m2. The research on the combustion characteristics of the PVC can be used to analyse the fire risk of the train and guide the formulation of safety measures.

A Comparison of the Behaviour of Spruce Wood and Polyolefins during the Test on the Cone Calorimeter

2013 ◽  
Vol 726-731 ◽  
pp. 4280-4287 ◽  
Author(s):  
Jozef Martinka ◽  
Emília Hroncová ◽  
Tomáš Chrebet ◽  
Karol Balog
Keyword(s):  
Heat Flux ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Cone Calorimeter ◽  
Lower Sensitivity ◽  
Average Heat ◽  
Fire Propagation ◽  
Spruce Wood

This article deals with comparison of the behaviour of spruce wood and polyolefins (polyethylene PE and polypropylene PP) during the test on the cone calorimeter. Samples were tested on the cone calorimeter at heat flux of 20 and 40 kW/m2. An evaluation of the behaviour of examined materials was based on the determination of the maximum and the average heat release rate, yield of carbon monoxide (CO), and relative comparison of tendency to fire propagation in a flashover phase. The tendency of materials to fire propagation in the flashover phase was evaluated based on the Pearson ́s correlation, the Spearman ́s correlation and the Kendall ́s correlation coefficient of HRR-CO and CO2-CO. Spruce wood showed better properties in comparison with PE and PP in all evaluated parameters (the maximum and the average heat release rate, the yield of CO, and also the resistance to fire propagation in the flashover phase. Additionally, spruce wood showed significantly lower sensitivity of dependence of the maximum and also the average heat release rate on external heat flux.

scholarly journals Use of the cone calorimeter to detect seasonal differences in selected combustion characteristics of ornamental vegetation

2005 ◽  
Vol 14 (3) ◽  
pp. 321 ◽  
Author(s):  
David R. Weise ◽  
Robert H. White ◽  
Frank C. Beall ◽  
Matt Etlinger
Keyword(s):  
Moisture Content ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Cone Calorimeter ◽  
Mass Loss Rate ◽  
Combustion Characteristics ◽  
Release Rates ◽  
Intermediate Scale ◽  
Time To Ignition

The flammability of living vegetation is influenced by a variety of factors, including moisture content, physical structure and chemical composition. The relative flammability of ornamental vegetation is of interest to homeowners seeking to make their homes ‘fire safe’. The relative importance of the factors influencing fire behaviour characteristics, such as flammability, is unknown. In the present study, oxygen consumption calorimetry was used to obtain selected combustion characteristics of ornamental vegetation. Peak heat release rate, mass loss rate, time to ignition and effective heat of combustion of 100 × 100-mm samples of foliage and small branches were measured using a bench-scale cone calorimeter. Green and oven-dry samples of 10 species were collected and tested seasonally for a period of 1 year. Similar measurements were made on whole shrubs in an intermediate-scale calorimeter. The range of cone calorimeter peak heat release rates for green and oven-dry samples was 1–176 and 49–331 kW m−2, respectively. Moisture content significantly reduced heat release rates and increased time to ignition. Peak heat release rates for Olea europea and Adenostoma fasciculatum were consistently highest over the year of testing; Aloe sp. consistently had the lowest heat release rate. The correlation of peak heat release rates measured by the cone calorimeter and an intermediate-scale calorimeter was statistically significant yet low (0.51). The use of the cone calorimeter as a tool to establish the relative flammability rating for landscape vegetation requires additional investigation.

Combustion Performance of Composite Floor with Different Radiant Heat Flux

2014 ◽  
Vol 501-504 ◽  
pp. 2415-2418
Author(s):  
Yan Ying Xu ◽  
Ruo Jun Wang ◽  
Jian Chen ◽  
Lu Chao Li
Keyword(s):  
Heat Flux ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Ignition Time ◽  
Radiation Heat ◽  
Radiation Heat Flux ◽  
Combustion Performance ◽  
Wood Flooring ◽  
Engineered Wood

The combustion performance of engineered wood flooring and intensive composite floor under the different radiation heat flux were experimented by cone calorimeter. Fire parameters were measured including the ignition time and heat release rate. Experimental results show that the ignition time of engineered wood flooring is much lower than intensive composite floor, and the ignition time are decreased with the increase of radiation heat flux. The heat release rate (HRR) curve has two peaks under the same radiation heat flux, and the first peak of the heat release rate of engineered wood flooring occurs significantly earlier than intensive composite floor. The heat release rate is increased and the first peak significantly ahead of time with the increase of the radiation intensity

Influence of grammage on heat release rate of polypropylene fabrics

2017 ◽  
Vol 36 (1) ◽  
pp. 30-46 ◽  
Author(s):  
Nicolas Hernandez ◽  
Rodolphe Sonnier ◽  
Stéphane Giraud
Keyword(s):  
Heat Flux ◽  
Growth Rate ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Cone Calorimeter ◽  
Heat Fluxes ◽  
Fire Growth ◽  
Time To Ignition ◽  
Moderate Change

The flammability of nine polypropylene fabrics or sheets has been tested using cone calorimeter at various heat fluxes (25, 35, 50, and 75 kW/m2) in order to assess the relevance of this fire test for thermally thin materials. The chosen procedure uses a grid and allows maintaining a constant exposed surface during the test, except for the lightest fabric. The structure of the knitted fabrics has a relatively small influence on the main flammability parameters. On the contrary, the area density of the sample (from 218 to 5729 g/m2) impacts strongly the time to ignition, the peak of heat release rate, and the increase in heat release rate after ignition (fire growth rate). At a fixed heat flux, thicker is the sample, higher are the time to ignition and the peak of heat release rate and lower is the fire growth rate. Moreover, thick samples exhibit the highest sensitivity of peak of heat release rate and the lowest sensitivity of fire growth rate to heat flux. This study emphasizes the fact that a moderate change in weight may have a significant influence on cone calorimeter results, without any significance on real flammability.

Analysis on the Combustion Performance of the MMFU-Boric Acid/Borax Treated Poplar Wood

2012 ◽  
Vol 174-177 ◽  
pp. 375-379
Author(s):  
Yu Bo Chai ◽  
Jun Liang Liu ◽  
Zhen Xing
Keyword(s):  
Boric Acid ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Oxygen Index ◽  
Mass Loss Rate ◽  
Ignition Time ◽  
Untreated Wood ◽  
Good Effect ◽  
Combustion Performance

In this study, Melamine-methanol-formaldehyde-urea (MMFU) resin and the mixture of MMFU/boric acid/borax (MBB) were used as the modification solutions to impregnate wood from poplar plantation. The combustion performance of the wood before and after impregnation treatment was investigated by using the oxygen index apparatus and cone calorimeter. Results showed that the oxygen index of the MMFU and MBB treated wood both increased. Compared with the untreated wood, the MMFU and MBB treatment significantly delayed the ignition time and the appearance of peak value of the heat release rate (HRR) during the combustion. The MMFU and MBB treatment also reduced the heat release rate (HRR), total heat release (THR), mass loss rate (MLR), generation rate of carbon monoxide (GCO) as well as total smoke release (TSR) significantly. Both MMFU and MBB exhibited good effect of smoke suppression on wood, while MBB had better flame retardancy than MMFU. Boric acid/borax exerted excellent synergistic effect of fire resistance on MMFU.

Fire performance of continuous glass fibre reinforced polycarbonate composites: The effect of fibre architecture on the fire properties of polycarbonate composites

2018 ◽  
Vol 53 (12) ◽  
pp. 1705-1715 ◽  
Author(s):  
Yousof M Ghazzawi ◽  
Andres F Osorio ◽  
Michael T Heitzmann
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Glass Fibre ◽  
Mass Loss Rate ◽  
Fibre Reinforcement ◽  
Fire Performance ◽  
Cone Calorimetry ◽  
Glass Fibre Reinforced ◽  
Fire Properties

The fire performance of polycarbonate resin and the role of glass fibre reinforcement in altering the fire performance was investigated. Three different fibre weaves with comparable surface density, plain, twill, and unidirectional glass fabrics, were used as reinforcements. E-glass fabrics were solution-impregnated with polycarbonate/dichloromethyl, laid up, and compression-moulded to consolidate the glass fibre reinforced polycarbonate composite. Cone calorimetry tests with an incident radiant flux of 35 kW/m2 were used to investigate the fire properties of polycarbonate resin and its composites. Results showed that glass fibre reinforcement improves polycarbonate performance by delaying its ignition, decreasing its heat release rate, and lowering the mass loss rate. The three fibre weave types exhibited similar time to ignition. However, unidirectional fibre had a 35% lower peak heat release rate followed when compared to plain and twill weave fibres.

Combustion Characteristics of Sitka Spruce Litter by Microcalorimetry

1997 ◽  
Vol 15 (6) ◽  
pp. 481-487 ◽  
Author(s):  
J.C. Jones
Keyword(s):  
Heat Release ◽  
Kinetic Parameters ◽  
Heat Release Rate ◽  
Release Rate ◽  
Ignition Temperature ◽  
Sitka Spruce ◽  
Combustion Characteristics ◽  
Field Situation

A sample of Sitka Spruce litter has been examined in a microcalo rimeter at temperatures up to 58°C, and kinetic parameters deduced from the re sults in a way which is explained step by step. The kinetic parameters were then used to predict the ignition temperature of the material in a field situation. Input to this calculation includes measured heat-release rate at incipient ignition of a different litter, reported independently.

Retardant Properties of Nanosilica/PTFE Nanoparticals-Reinforced Polypropylene

2014 ◽  
Vol 1004-1005 ◽  
pp. 77-84 ◽  
Author(s):  
Zhen Lu Zhang ◽  
Dong Li Li ◽  
Wen Cai Xu ◽  
Ya Bo Fu ◽  
Rui Juan Liao
Keyword(s):  
Mass Loss ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Loss Rate ◽  
Mass Loss Rate ◽  
Thermoplastic Polymer ◽  
Maximum Heat ◽  
Average Mass ◽  
Melting Characteristics

This work reports the flammability properties of Nanocomposites reinforced with silica and PTFE nanoparticles and toughened with an elastomeric ethylene-vinyl acetate (EVA). Through trial and simulation study of the flame retardant thermoplastic polymer and melting characteristics of PP in the combustion process.The study found that modified PP composites have good flame retardancy compared to PP in case of fire relatively.In the study,the melting characteristics of the thermoplastic polymer affected the mass loss rate in the combustion stage.Nanocomposites experienced low plastic mass loss compared with PP, this has been related to pyrolysis mechanism of polymer.In general,The polymers undergoing depolymerization will lead to a rapid volatilization and therefore experienced much less melting.The results showed that:total heat release of nanocomposites was higher than polypropylene, while the average heat release rate, the maximum heat release rate, the average effective heat of combustion, the average mass loss rate, the average specific extinction area, and other indicators were lower than polypropylene.

Synchronization During Multi-Mode Thermoacoustic Oscillations in a Liquid-Fueled Gas Turbine Combustor at Elevated Pressure

2019 ◽  
Author(s):  
Mitchell L. Passarelli ◽  
J. D. Maxim Cirtwill ◽  
Timothy Wabel ◽  
Adam M. Steinberg ◽  
A. J. Wickersham
Keyword(s):  
Heat Release ◽  
Gas Turbine ◽  
Heat Release Rate ◽  
Release Rate ◽  
High Speed ◽  
Elevated Pressure ◽  
Fuel Injector ◽  
Frequency Pulling ◽  
Industrial Gas Turbine ◽  
Thermoacoustic Oscillations

Abstract This paper analyzes intermittent self-excited thermoacoustic oscillations in which the pressure (P′) and heat release rate (q̇′) fluctuations are harmonically coupled. That is to say, P′ and q̇′ do not oscillate at the same frequencies, but rather at frequencies in integer ratios. Thus, this system represents a case dominated by nonlinear cross-mode coupling. The measurements were obtained in an optically-accessible combustor equipped with an industrial gas turbine fuel injector operating with liquid fuel under partially-premixed conditions at elevated pressure. High-speed chemiluminescence (CL) imaging of OH* was used as an indicator of the heat release rate. The data was processed using spectral proper orthogonal decomposition (SPOD) to isolate the dominant heat release and pressure modes. Synchronization theory was used to determine when the modes are coupled and how their interaction manifests in the measurements, particularly how it relates to the observed intermittency. The results show three distinct intervals of synchronized oscillation shared by all the mode pairs analyzed. The first interval exhibits the same characteristics as a pair of noisy, phase-locked self-oscillators, with phase-slipping and frequency-pulling. While the behaviour of the second interval differs among mode pairs, strong frequency-pulling is observed during the third interval for all pairs.

DNS of Flame-Wall Interaction and Heat Transfer in a Constant Volume Vessel

2010 ◽  
Author(s):  
Akihiko Tsunemi ◽  
Yoshihiro Horiko ◽  
Masayasu Shimura ◽  
Naoya Fukushima ◽  
Seiji Yamamoto ◽  
...  
Keyword(s):  
Heat Flux ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Burning Velocity ◽  
Fluid Velocity ◽  
Pressure Rise ◽  
Kinetic Mechanism ◽  
Constant Volume ◽  
Wall Interaction

Direct numerical simulations of turbulent hydrogen/air and methane/air premixed flames in a rectangular constant volume vessel have been conducted with considering detailed kinetic mechanism to investigate flame behaviors and heat losses. For the hydrogen cases, since heat release rate increases with pressure rise due to dilatation during combustion in the constant vessel, heat flux on a wall also increases. For the methane cases, the pressure increase does not raise wall heat flux significantly because of the decrescence of heat release rate caused by thermo-chemical reaction near a wall. Pressure waves caused by wall reflection fluctuate flame propagation for the hydrogen flames. Flame displacement speed decreases remarkably at the moment when the pressure wave passes through flame fronts from unburnt side to burnt side. However, the turbulent burning velocity at that time does not decrease because of increases of fluid velocity normal to the flame fronts.

Sign in / Sign up

Export Citation Format

Share Document