scholarly journals Using Steel-Smelting Slag as a Raw Material Component in the Production of Asphalt Concrete

2020 ◽  
Vol 157 ◽  
pp. 06010
Author(s):  
Dmitry Kuznetsov ◽  
Marina Vysotskaya ◽  
Albert Burgonutdinov

The possibility of using polydisperse steel-smelting slag for the production of type B asphalt concrete is investigated, the possibility of its use as a mineral powder, crushing screening and crushed stone is considered. As a result of the study, it was found that a promising area for the use of slag raw materials in the technology for the preparation of asphalt mixes is: as a mineral powder - without additional processing steps; crushing screening - with the development of additional technological operations. The use of raw materials as crushed stone is impractical because of the high average density of the final asphalt mixture. Based on the test results, the characteristics of the fatigue properties of asphalt concrete from fine-grained dense mixtures of type B made on mineral powders from slag and limestone were obtained. It was established that at the initial moment, a large number of cycles to failure are characterized by compositions on slag powder, however, samples from this series tested after 45 days showed a significant rigidity increase and were destroyed earlier than similar samples on limestone. Obviously, this phenomenon is associated with an increase in the brittle properties of the material due to the formation of crystallization-condensation bonds in the structure of asphalt concrete containing slag.

2021 ◽  
Vol 2021 (24) ◽  
pp. 193-205
Author(s):  
Ivan Kopynets ◽  
◽  
Volodymyr Kaskiv ◽  
Оleksii Sokolov ◽  
◽  
...  

Introduction. Mineral powder is an important structural component of asphalt concrete. Mineral powder is the output material obtained after crushing of rocks or powdery remains of the industry. It is made by grinding the following hard rocks: dolomitized limestone, dolomite, limestone. Non-carbonate raw materials and industrial wastes are also used as raw materials. Problem statement. Road construction with the arrangement of asphalt concrete pavements requires a number of components of these mixtures. Due to this, the need in scarce carbonate mineral powders is growing. Therefore, it is advisable to consider researches directed on studying a number of by-products of industry in order to use them as a mineral powder of asphalt concrete. Purpose. To analyze the existing experience of using industrial waste as a mineral powder in production of asphalt concrete mixture for further introduction and improvement of environmental safety and operational characteristics of pavement due to new road construction materials. Materials and methods. Analysis of information sources and experience in the use of industrial waste as a mineral powder and study of requirements for materials and their composition. Results. An analytical review of the experience of using industrial waste as a mineral powder was performed. Various materials have been studied and analyzed, requirements for materials, their particle size distribution, content in asphalt concrete mixture had been established. Conclusions. Analysis of information sources regarding use of industrial waste as a raw material for the production of mineral powder had determined that they are used in the whole volume in different countries and in most cases in road construction. It had been found that the use of various wastes during road construction is a viable option that needs further study.


Coatings ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1091
Author(s):  
Alexandra Inberg ◽  
Dana Ashkenazi ◽  
Yishai Feldman ◽  
Omri Dvir ◽  
Deborah Cvikel

Fragments of decorated floor tiles were retrieved from the Akko Tower shipwreck, Israel. Most tiles were made of bright brown fired clay with a white glaze decorated with colored stenciled motifs (Type A); and others consisted of a red-brown fired clay body, coated with a brown pigment covered with transparent brown glaze (Type B). This study aimed to characterize the two tile types; to reveal information concerning the manufacturing process; and to determine the origin of their raw material. A multidisciplinary approach was used, including light microscopy, SEM-EDS, electron probe microanalysis with wavelength-dispersive X-ray spectroscopy (EPMA-WDS), XRD, Raman spectroscopy, and time-of-flight secondary ion mass spectrometry (TOF-SIMS) analyses. The characterization of both tile types demonstrated the use of different raw materials. The Type A tiles were covered with tin-opacified majolica glaze and colored with various mixtures of pigments. The blue color was due to pigment rich in cobalt; the yellow color was due to Naples yellow and lead-tin yellow I minerals; and the green, orange, and brown colors were all prepared by mixing the Naples yellow pigment with different minerals. These majolica glaze tiles were probably manufactured in Sicily. The brown coating of the Type B tiles was due to pigment rich in lead and iron minerals. These tiles were produced with different manufacturing processes, and apparently made in France.


2001 ◽  
Vol 64 (2) ◽  
pp. 201-207 ◽  
Author(s):  
AGNÈS BRACONNIER ◽  
VÉRONIQUE BROUSSOLLE ◽  
SYLVIE PERELLE ◽  
PATRICK FACH ◽  
CHRISTOPHE NGUYEN-THE ◽  
...  

A molecular method was used for the detection of Clostridium botulinum spores of type A, B, and E in commercial cooked and pasteurized vegetable purées and in the raw materials (vegetables and other ingredients). The method allowed the detection of less than 8 spores/g of product for C. botulinum type A, less than 1 spore/g for proteolytic type B, less than 21 spores/g for nonproteolytic type B, and less than 0.1 spore/g for type E. Thirty-seven samples of raw vegetables and ingredients were tested for the presence of C. botulinum type A, B, and E; 88 and 90 samples of vegetable purées were tested, respectively, for the presence of C. botulinum type A and B and for the presence of C. botulinum type E. All samples were negative, suggesting that the prevalence of C. botulinum in these vegetable purées and the raw ingredients is probably low.


Author(s):  
Anna Trautvain ◽  
V. Yadykina ◽  
E. Mulenko

the article presents the results of testing asphalt samples based on activated mineral powder from silica-containing raw materials. Activated filler was obtained by joint grinding of waste wet magnetic separation (WMS) of ferruginous quartzites of the Kursk Magnetic Anomaly in a spherical planetary mill in the presence of surfactants (stearic acid, adhesive additive Amdor-10) and bitumen. First of all, it should be noted that the use of activated mineral powder in the composition of asphalt concrete mixture led to an increase in the packing density of the composite. This was reflected not only in the technological process, but also contributed to the decrease in the porosity of the mineral core. It was found that the use of surfactants in the process of grinding mineral powder made it possible to increase the strength of asphalt concrete samples. However, the change in the crack resistance and shear resistance of asphalt concrete specimens, determined from the ratio of the corresponding compressive strengths, did not occur (table). This is due to the fact that there has been a proportional change in all the strength characteristics at different temperatures. Analysis of the physical-mechanical characteristics of the properties of asphalt concrete led to the conclusion that it was possible to use activated mineral powder from waste WMS as a component of asphalt concrete mixtures.


Author(s):  
Sokhibjon Turdaliyevich Matkarimov ◽  
Anvar Abdullayevich Yusupkhodjayev ◽  
Bakhriddin Berdiyarov Berdiyarov

In article questions of development low-waste technologies of processing of steel-smelting slag are considered, gland allowing by extraction and its connections from steel-smelting slag to receive additional raw materials for production became, and the remains to use in building industry. Studying of gravitational methods of enrichment of steel-smelting slag and heat treatment the ore-fuel of pellets is the basis for work. Proceeding from it, in work modern physic-mechanical, chemical and physical and chemical methods of researches (UV-spectroscopy, electronic microscopy, the granulometric analysis) are used.


2018 ◽  
Vol 3 ◽  
pp. 56-64
Author(s):  
Iryna Tsykhanovska ◽  
Victoria Evlash ◽  
Alexandr Alexandrov ◽  
Tetiana Lazareva ◽  
Tetiana Yevlash

Today in Ukraine the share of low-quality bakery products is near 20–25 %, because they often don’t correspond to quality standards and sanitary norms, because of being produced of flour with low bakery properties. That is why new raw material sources, functional ingredients and so on are searched for in bread technologies. For using new raw material and food supplement types, it is necessary to know their functional-technological properties (FTP) that allows to prognosticate the behavior of powder-like raw materials and food supplements in food masses at technological processing and storage of ready products. The water-retaining capacity (WRC) is one of main functional-technological parameters of carbohydrate-containing raw materials, because it favors the outcome, structural-mechanical properties and quality characteristics of ready products. The authors introduced “Magnetofood” polyfunctional food supplement for increasing WRC of rye-wheat dough. For grounding the mechanism of forming supramolecular groups in carbohydrate food systems: Magnetofood-polysacharide-water, there was studied the influence of “Magnetofood” food supplement on processes of hydration, swelling and water-retention by rye-wheat starch and rye-wheat flour. It was established, that introduction of “Magnetofood” food supplement in rye-wheat starch and flour in amounts: 0,10; 0,15; 0,20 % to the mass of starch or flour increases swelling and water-retaining capacity (WRC) of starch and flour: swelling in 1,3–1,5 and 1,5–2,25 times, respectively; WRC in 1,10–1,15 and 1,1–1,3 times, respectively. The rational dose of “Magnetofood” food supplement – 0,15 % to the mass of dry raw material was experimentally set. There was studied the influence of “Magnetofood” food supplement on rheological properties of water suspensions of rye-wheat starch and flour at different temperatures and different speeds of shift. It was established, that adding “Magnetofood” in amount 0,15 % favors increasing the effective viscosity of suspensions of experimental samples of starch and flour at temperatures: (23±2) ºС and (40±2) ºС comparing with control samples in average by 29,0 % – for starch and by 22,0 % – for flour at 23 °С and by 16,0 % – for starch and by 10,0 % – for flour at 40 °С. There was studied the dynamics of changing viscosity of colloid solutions of starch and flour, enriched with “Magnetofood” in amount 0,15 % to the mass of dry raw material in the keeping process at different temperatures and shift speed 9 s-1. There was established the increase of viscosity of suspensions of rye-wheat starch and flour in the process of infusion (especially at adding “Magnetofood”) that is connected with continuing hydration and swelling process. It was demonstrated, that the temperature increase of the colloid system from (23±20) ° С to (40±2) °С favors the increase of its viscosity – both at the initial moment and in infusion process during 30 min in average by 20,0–25,0 % at the expanse of the aforesaid processes. Moreover, adding “Magnetofood” accelerates and intensifies the processes of swelling and hydration of experimental samples of rye-wheat starch and flour comparing with control ones. The received experimental data may be used at elaborating the technology of rye-wheat bread, enriched with “Magnetofood” food supplement; and also at elaborating innovative technologies of carbohydrate food systems. The results of this study may be used at elaborating recipes and technologies of carbohydrate-containing food products for increasing their viscosity, water-retaining and stabilizing capacities.


2020 ◽  
Author(s):  
Kirill Yuryevich Tyuryukhanov ◽  
Konstantin Georgievich Pugin

There is an increase in motorization worldwide, which in turn requires the construction of high-quality roads and highways. In both new construction and reconstruction of the pavement, large volumes of natural mineral materials are used, placing a large technogenic load on environmental objects during their extraction. In a number of regions of the Russian Federation, there are not sufficient volumes of conditioned raw materials for the production of high-quality composite building materials, such as asphalt concrete and cement concrete mixtures. The use of industrial waste in the composition of building materials addresses this issue while both solving environmental issues and reducing the cost of road construction. This article shows that developed countries successfully use the resource potential of waste in the production of building materials. This article proposes the use of waste foundry sand as the mineral raw material in the production of asphalt concrete. The article presents research on the following: geometric shape, elemental composition of the surface of the particles of the waste foundry sand; bitumen capacity; and the adhesion of bitumen. Based on the obtained data, a technology was developed for producing hot sandy asphalt concrete in which the waste foundry sand is used as a fine mineral aggregate. Physico-mechanical properties of the obtained samples of asphalt concrete satisfy the requirements established in GOST for asphalt concrete. Keywords: waste foundry sand, asphalt concrete, industrial material, elemental composition, bitumen


2022 ◽  
Author(s):  
I. Romanenko

Abstract. Obtaining an artificial stone based on steel-smelting slag is possible as a result of carbonization of the feedstock in carbon dioxide. The feedstock - slag and carbon dioxide - are by-products from steel smelting in electric furnaces, which must be disposed of in order to improve the environmental situation in the region. The condition for obtaining the cementing ability of steelmaking slag is the preparation of a charge with certain properties and maturation technology: humidity, dispersion of the fine fraction and the maximum size of the coarse fraction, the ratio between the coarse and dispersed fractions, the concentration of carbon dioxide in the gas-air environment, temperature, pressure and flow time. carbonization reactions in the reactor, the magnitude of the pressure during the production of pressed articles, the process of stone maturation in the post-carbonization period.


2020 ◽  
Vol 7 (2) ◽  
Author(s):  
Sergey Andronov ◽  
Andrey Kochetkov ◽  
Igor Shashkov

During the construction of experimental sections of road surfaces in v. Ust-Kurdyum of the Saratov district of the Saratov region has been established the efficiency of production and application of cold fiber-containing dispersed-reinforced asphalt concrete mixtures with dispersed bitumen. A method for accelerating the formation of the structure of cold fiber-containing asphalt concrete by heat treatment of its surface is studied. Dispersed bitumen after drying the water film has good adhesion to concrete, asphalt concrete and other materials. The asphalt concrete formed as a result of curing on the basis of dispersed bitumen is high-strength, chemical-resistant, hydrophobic and environmentally friendly, corresponding to the existing regulatory requirements for asphalt concrete. For the production of asphalt mixtures, mass-produced equipment is suitable using materials commonly used in hot asphalt concrete: crushed stone, sand, mineral powder and bitumen. Operations on drying and heating of crushed stone and sand are excluded from the technological process. Asphalt concrete mix does not stick to the surface of rubberized rollers of vibratory rollers, which allows compacting mixtures with a high content of mineral powder at any time. There are fewer cracks on the surface of the compacted layer than when using a smooth-rolling roller. The technology is recommended for extended use on roads and streets of localities, and highways with low traffic intensity.


Sign in / Sign up

Export Citation Format

Share Document