scholarly journals The simulation of volume shrinkage for double-injection molding with PC and ABS

2018 ◽  
Vol 192 ◽  
pp. 01053
Author(s):  
Pichai Leklong ◽  
Wipoo sriseubsai
Keyword(s):  
Injection Molding ◽  
Weld Line ◽  
Acrylonitrile Butadiene Styrene ◽  
Volume Shrinkage ◽  
Melt Temperature ◽  
Double Injection ◽  
Molded Part ◽  
Packing Pressure ◽  
Injection Molded ◽  
Plastic Injection

The objective of this paper was to study and analyze the plastic injection molding parameters to reduce the volume shrinkage of double injection molded part. The specimen was molded with Acrylonitrile-butadiene-styrene (ABS) after Polycarbonate was molded as a half part. The weld line occurred at the haft of the molded part. The simulation with Moldex 3D R13 and the design of experiment with Taguchi method was used to perform the experiments and analyze the data to get the optimum of volume shrinkage. The results showed that melt temperature and packing pressure was significant to the volume shrinkage. When using low melt temperature and high packing pressure, the shrinkage was low and related to the thermal expansion of the material. It would be one of the parameters to the design of double injection molding.

Warpage Measurement of a Micro Electrical Fan on Micro-Injection Molding

2012 ◽  
Vol 184-185 ◽  
pp. 1651-1654
Author(s):  
Jeou Long Lee ◽  
Y. Lin ◽  
Y.K. Shen
Keyword(s):  
Injection Molding ◽  
Injection Pressure ◽  
Acrylonitrile Butadiene Styrene ◽  
Mold Temperature ◽  
Micro Injection Molding ◽  
Optimum Result ◽  
Suitable Material ◽  
Packing Pressure ◽  
Injection Molded ◽  
Packing Time

This study characterizes warpage of a micro-injection molded micro electrical fan using the Michelson interference method. This study conducts experiments to analyze different polymers-polypropylene (PP), polyamide (PA), acrylonitrile-butadiene styrene (ABS), ABS+ polycarbonate (PC), and polyoxymethylene (POM)-process parameters, such as mold temperature, injection temperature, injection pressure, injection time, packing time, and packing pressure, for a micro electrical fan. To obtain the optimum result (minimum warpage), this study assesses the effect (warpage) of each material on micro-injection molding. PA plastic is the very suitable material for micro electrical fan with Michelson interference analysis on micro-injection molding.

Reduction in Defect Rate by Taguchi Method in Plastic Injection Molded Components

2012 ◽  
Vol 488-489 ◽  
pp. 269-273 ◽  
Author(s):  
G.S. Dangayach ◽  
Deepak Kumar
Keyword(s):  
Injection Molding ◽  
Injection Pressure ◽  
Processing Parameters ◽  
Process Conditions ◽  
Melt Temperature ◽  
Defect Rate ◽  
Packing Pressure ◽  
Optimal Injection ◽  
Packing Time ◽  
Plastic Injection

In the present era, competition gets tougher; there is more pressure on manufacturing sectors to improve quality and customer satisfaction while decreasing cost and increasing productivity. These can be achieved by using modern quality management systems and process improvement techniques to reduce the process variability and driven waste within manufacturing process using effective application of statistical tools. Taguchi technique is well known technique to solve industrial problems. This technique is fast and can pinpoint the chief causes and variations. Plastic injection molding is suitable for mass production articles since complex geometries can be obtained in a single production step. The difficulty in setting optimal process conditions may cause defects in parts, such as shrinkage and warpage. In this paper, optimal injection molding conditions for minimum shrinkage were determined by the Taguchi design of experiment (DOE) approach. Polypropylene (PP) was injected in circular shaped specimens under various processing parameters: melt temperature, injection pressure, packing pressure and packing time. S/N ratios were utilized for determining the optimal set of parameters. According to the results, 2400 C of melt temperature, 75 MPa of injection pressure, 50 MPa of packing pressure and 15 sec. of packing time gave minimum shrinkage of 0.951% for PP. Statically the most significant parameter was melt temperature for the PP. Injection pressure had the least effect on the shrinkage. The defect rate was reduced from 14% to 3%.

Comparison between Single and Multi Gates for Minimization of Warpage Using Taguchi Method in Injection Molding Process for ABS Material

2013 ◽  
Vol 594-595 ◽  
pp. 842-851 ◽  
Author(s):  
S.M. Nasir ◽  
Khairul Azwan Ismail ◽  
Z. Shayfull ◽  
Norshah Afizi Shuaib
Keyword(s):  
Injection Molding ◽  
Acrylonitrile Butadiene Styrene ◽  
Mold Material ◽  
Injection Molding Process ◽  
Inlet Temperature ◽  
Molding Process ◽  
Melt Temperature ◽  
Thermoplastic Material ◽  
Packing Pressure ◽  
Packing Time

In this study, a mold is designed in single and dual type of gate in order to investigate the deflection of warpage for thick component in injection molding process. Autodesk Moldflow Insight software was used as a medium for experimental tested. Nessei NEX 1000 injection molding machine and P20 mold material details were entered in this study to get more accurate data on top of Acrylonitrile Butadiene Styrene (ABS) as a molded thermoplastic material. Taguchi orthogonal array, analysis of Signal to Noise (S/N) ratio and Analysis of Variance (ANOVA) were implemented to get the best combination of parameter and significant factor that affect the warpage problem for both types of gates. Coolant inlet temperature, melt temperature, packing pressure and packing time are the selected parameter that used in this study. A conformation test is conducted to verify the combination parameters optimized. From the result, multi gates used was founded that can decrease the deflection of warpage for thick product. From ANOVA, the most significant factor is melt temperature for single gate, and coolant inlet temperature for multi gate. Packing pressure and packing time were slightly influence on warpage problem for both studies.

Effect of Weld Line Defects on Electrical Conductivity of Injection Molded Parts with Carbon Nano Fibers/PP Composites

2011 ◽  
Vol 233-235 ◽  
pp. 1136-1140
Author(s):  
Lei Xie ◽  
Xiao Yong Tian ◽  
Wang Qing Wu ◽  
Di Chen Li ◽  
Bing Yan Jiang ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Injection Molding ◽  
Conductive Polymer ◽  
Weld Line ◽  
Injection Molding Process ◽  
Molding Process ◽  
Molded Part ◽  
Molded Parts ◽  
Line Defects ◽  
Injection Molded

As well known, the weld line defect in injection molding process results detrimental to mechanical properties and surface quality. However, the electrical conductivity of the injection molded part is influenced as well. In this study, in order to reveal the mechanism of the weld line affecting the electrical conductivity of injection molding parts, the conductive polymer composites with various carbon nanofibers filling contents were compounded. Those composites were formed as the tensile samples with and without weld line defects by injection molding process. According to the electrical resistance measurements for the samples, it can be found that at relative low filling content of 10wt%, the weld line contributes to increase the electrical conductivity of the injection molding parts due to its effect on nanofibers’ orientation. However, when the filling content is higher than 20wt%, this effect is not significant any more.

scholarly journals Experimental And Numerical Studies of Shrinkage and Sink Marks On Injection Molded Polymer Gears

2021 ◽  
Author(s):  
Bikram Solanki ◽  
Hapreet Singh ◽  
Tanuja Sheorey
Keyword(s):  
Injection Molding ◽  
Injection Molding Process ◽  
Molding Process ◽  
Melt Temperature ◽  
Numerical Studies ◽  
Packing Pressure ◽  
Injection Molded ◽  
Sink Marks ◽  
Plastic Gears ◽  
Packing Time

Abstract Injection molding is an efficient and most economical process employed for the mass production of plastic gears and helps to reduce the processing time and cost required to produce the desired geometry. However, significant process and product qualification of plastic gears face the shrinkage and sink marks issues during cooling and after ejection. In present work, the best gate locations and flow resistance analysis along with a polypropylene (PP) were carried out using Autodesk Moldflow Insight 2019.05. The numerical and experimental study was conducted to evaluate the effect of packing pressure, packing time, and melt temperature on diametric shrinkage, mass, and sink marks of PP gear. The results show that by increasing packing pressure and packing time, the diametric shrinkage decreased but mass increased. However, as the melt temperature increased the diametric shrinkage also increased but the mass decreased. The minimum diametric shrinkage of 0.562% was found in numerical analysis and 1.619% found in an experimental analysis at the same injection molding process parameters. Mostly, the sink marks were observed in the gear surface between hub and dedendum circle.

Study on Optical Properties of Microstructure of Lightguiding Plate for Micro Injection Molding and Micro Injection-Compression Molding

2006 ◽  
Vol 505-507 ◽  
pp. 229-234 ◽  
Author(s):  
Yung Kang Shen ◽  
H.J. Chang ◽  
C.T. Lin
Keyword(s):  
Optical Properties ◽  
Injection Molding ◽  
Digital Camera ◽  
Mold Temperature ◽  
Compression Molding ◽  
Micro Injection Molding ◽  
Melt Temperature ◽  
Packing Pressure ◽  
Injection Compression Molding ◽  
Better Than

The purpose of this paper presents the optical properties of microstructure of lightguiding plate for micro injection molding (MIM) and micro injection-compression molding (MICM). The lightguiding plate is applied on LCD of two inch of digital camera. Its radius of microstructure is from 100μm to 300μm by linearity expansion. The material of lightguiding plate uses the PMMA plastic. This paper uses the luminance distribution to make a comparison between MIM and MICM for the optical properties of lightguiding plate. The important parameters of process for optical properties are the mold temperature, melt temperature and packing pressure in micro injection molding. The important parameters of process for optical properties are the compression distance, mold temperature and compression speed in micro injection-compression molding. The process of micro injection-compression molding is better than micro injection molding for optical properties.

scholarly journals Effects of Injection Molding Screw Tips on Polymer Mixing

2018 ◽  
Vol 62 (3) ◽  
pp. 241-246 ◽  
Author(s):  
Dániel Török ◽  
József Gábor Kovács
Keyword(s):  
Injection Molding ◽  
Processing Parameters ◽  
Raw Material ◽  
Molding Machine ◽  
Surface Color ◽  
Melt Temperature ◽  
Injection Molding Machine ◽  
Aesthetic Appearance ◽  
Molded Parts ◽  
Injection Molded

In all fields of industry it is important to produce parts with good quality. Injection molded parts usually have to meet strict requirements technically and aesthetically. The aim of the measurements presented in our paper is to investigate the aesthetic appearance, such as surface color homogeneity, of injection molded parts. It depends on several factors, the raw material, the colorants, the injection molding machine and the processing parameters. In this project we investigated the effects of the injection molding machine on surface color homogeneity. We focused on injection molding screw tips and investigated five screw tips with different geometries. We produced flat specimens colored with a masterbatch and investigated color homogeneity. To evaluate the color homogeneity of the specimens, we used digital image analysis software developed by us. After that we measured the plastication rate and the melt temperature of the polymer melt because mixing depends on these factors. Our results showed that the screw tips (dynamic mixers) can improve surface color homogeneity but they cause an increase in melt temperature and a decrease in the plastication rate.

Observation and Evaluation of Scratch Damage Characteristics of Injection Molded, Rubber Toughened Poly(Methylmethacrylate)

2013 ◽  
Author(s):  
Jihun An ◽  
Byoung-Hyun Kang ◽  
Byoung-Ho Choi ◽  
Hyoung-Jun Kim
Keyword(s):  
Electron Microscopy ◽  
Injection Molding ◽  
Acrylonitrile Butadiene Styrene ◽  
Damage Mechanism ◽  
Damage Characteristics ◽  
Rubber Toughened ◽  
Rubber Particles ◽  
Injection Molded ◽  
Engineering Polymers ◽  
Scratch Tests

Poly(methylmethacrylate) (PMMA) is one of popular engineering polymers for many engineering applications such as glass substitutes, medical applications, electronic goods, optical fibers, laser disk optical media and so on. PMMA is a lightweight material with excellent optical properties and balanced mechanical properties. However, PMMA is commonly blended with various functional fillers, and rubber particles are one of them to improve the low impact toughness of unfilled PMMA comparing with other engineering polymers such as polycarbonate (PC), acrylonitrile-butadiene-styrene (ABS) copolymer and so on. PMMA is generally used to make exterior of a commercial product, so scratch characteristics of PMMA is very important in terms of the aesthetic point of view. In this paper, rubber toughened PMMA plates are prepared by injection molding, and static and progressive scratch tests are performed. Samples are prepared by various injection molding conditions, and two orientations (machine direction and transverse direction) of the injection molded plate are considered for scratch tests. Three scratch damage mechanism stages, i.e. mar/ploughing, whitening and cutting stages, are identified by observing the scratch damages and two critical loads to define the variation of scratch damage mechanisms are recorded to evaluate the scratch resistance of rubber toughened PMMA samples. Scratch damage characteristics are examined by various microscopy techniques such as optical microscopy, scanning electron microscopy, transmission electron microscopy, atomic force microscopy, optical profiler and so on. It is clearly observed that scratch damage characteristics of rubber toughened PMMA are changed sensitively for various test conditions due to rubber particles, so it can be known that the mold design should be carefully optimized to improve scratch characteristics of injection molded rubber toughened PMMA product.

Dynamic Modeling and Control of Packing Pressure in Injection Molding

1994 ◽  
Vol 116 (2) ◽  
pp. 244-249 ◽  
Author(s):  
J. Hu ◽  
J. H. Vogel
Keyword(s):  
Injection Molding ◽  
Closed Loop ◽  
Good Control ◽  
Pressure Control ◽  
Physical Parameters ◽  
Closed Loop System ◽  
Modeling And Control ◽  
Packing Pressure ◽  
And Control ◽  
Plastic Injection

A dynamic model of injection molding developed from physical considerations is used to select PID gains for pressure control during the packing phase of thermo-plastic injection molding. The relative importance of various aspects of the model and values for particular physical parameters were identified experimentally. The controller gains were chosen by pole-zero cancellation and root-locus methods, resulting in good control performance. Both open and closed-loop system responses were predicted and verified, with good overall agreement.

Effects of process parameters on the formability of sheet metal during plastic injection forming

2020 ◽  
Vol 62 (5) ◽  
pp. 535-543
Author(s):  
Mirigul Altan ◽  
Bora Sener ◽  
Mirigul Altan
Keyword(s):  
Injection Molding ◽  
Sheet Metal ◽  
Injection Pressure ◽  
Industrial Applications ◽  
Effective Parameter ◽  
Melt Temperature ◽  
Injection Speed ◽  
Aluminum Sheets ◽  
Plastic Injection ◽  
Thinning Rate

Abstract Plastic injection forming (PIF) is an alternative sheet metal forming method for complex geometrical parts with dimensions in low tolerance. This method is a combination of injection molding and hydroforming in which a molten polymer material has been injected over a sheet metal via a plastic injection molding machine. In this study, aluminum sheets 1.5 mm thick were shaped by PIF at various injection pressures, melt temperatures and injection speed. The effects of these parameters on the formability of the sheet metal were investigated using the experimental design technique. The thinning rate, flange radius and the hardness values of the shaped sheets were considered in the experimental study. Injection pressure was found to be the most effective parameter and melt temperature was the second degree effective parameter for the thinning rate. The usability of the PIF process in industrial applications as an alternative method was emphasized by comparing PIF with conventional hydroforming by means of the finite element method (Ls-Dyna). A 2.07 % deviation was observed between the FE results for hydroforming and the experimental results for PIF.

Sign in / Sign up

Export Citation Format

Share Document