scholarly journals Impact of a locomotive engine modernization on fuel consumption

2021 ◽  
Vol 338 ◽  
pp. 01001
Author(s):  
Maciej Andrzejewski ◽  
Paweł Daszkiewicz ◽  
Patryk Urbański ◽  
Łukasz Rymaniak ◽  
Aleksandra Woch
Keyword(s):  
Fuel Consumption ◽  
Internal Combustion Engines ◽  
Test Bench ◽  
Negative Impact ◽  
Pollutant Emissions ◽  
Combustion Engines ◽  
Drive Unit ◽  
Rail Vehicles ◽  
Wear And Tear ◽  
Locomotive Engine

Vehicles used in rail transport are characterized by a long service life, which is caused, among others, by the high cost of their purchase. In Poland, the average age of freight diesel locomotives exceeds 40 years. Increasing the wear and tear of vehicles has an impact on many aspects of machine operation, including environmental pollution. Significant wear and degradation of the powertrain components contributes to the increase in pollutant emissions and fuel consumption, which is closely correlated with the production of carbon dioxide. Modernizations involving the replacement of the drive unit are performed in order to reduce the negative impact of rail vehicles on the environment. The article compares the energy consumption of the ST44 locomotive prior to and after modernization. The older 14D40 two-stroke internal combustion engines were replaced with a more modern engine unit 12CzN26/26. Fuel consumption tests were carried out on a test bench using a OW6300 water resistor.

ME´RIME´E: A Simulation Software to Study Diesel Engines Used for Military Propulsion

2002 ◽  
Author(s):  
Xavier Tauzia ◽  
Pascal Chesse ◽  
Jean-Franc¸ois Hetet ◽  
Arnaud Bonin
Keyword(s):  
Internal Combustion Engines ◽  
Test Bench ◽  
Simulation Software ◽  
Pollutant Emissions ◽  
Combustion Engines ◽  
Ground Vehicles ◽  
Simulation Code ◽  
Engine Simulation ◽  
Computer Research ◽  
Second Category

The design and development of internal combustion engines, and by extension of complete powertrains for ground vehicles, constitute a particularly complex, costly and time consuming task. As a result, numerical simulation is now commonly used by engine manufacturers and vehicle designers in addition to test bench experiments. Engine simulation codes can be divided into three main categories, with very different objectives and levels of complexity: CFD codes, thermodynamic codes and real time codes. This paper presents the MERIMEE simulation code, which belongs to the second category (MERIMEE is the French acronym for Computer Research and Study Model for Engines and their Equipment). Jointly developed by Ecole Centrale de Nantes (for the models) and the CS-SI Company (for the software development) it is used by ETAS (French Army) for the development and study of complete powertrains designed for military ground propulsion. The main models used to simulate the engine behavior are first briefly described. Then, the software architecture, the interface as well as the programming and numerical aspects are described. Finally, some significant results are shown and compared with experimental data. They deal with steady state and transient engine behavior in addition to the evaluation of pollutant emissions.

Review of Laser Ignition for Methane-Air Mixtures

2015 ◽  
Vol 727-728 ◽  
pp. 592-596
Author(s):  
Hong Tao Wang ◽  
Cang Su Xu
Keyword(s):  
Fuel Consumption ◽  
Internal Combustion Engines ◽  
Pollutant Emissions ◽  
Laser Ignition ◽  
Combustion Engines ◽  
Ignition System ◽  
Spark Plug ◽  
Induced Ignition ◽  
Ignition And Combustion ◽  
Promising Development

Reducing vehicle pollutant emissions and fuel consumption is becoming more and more important challenges, while lean-burning are a promising development. However, lean-burning may leads to other problems including combustion instability and incomplete combustion. Recently, laser ignition system has become an attractive field of research in order to replace the conventional spark plug ignition systems in the internal combustion engines to solve problem above. Moreover, methane was regarded as very promising fuel. Therefore, the objective of this article is to review the ignition and combustion characteristics of methane-air mixtures by laser-induced ignition.

scholarly journals Highest efficiency and ultra low emission – internal combustion engine 4.0

2020 ◽  
Vol 180 (1) ◽  
pp. 8-16
Author(s):  
Hubert FRIEDL ◽  
Günter Fraidl ◽  
Paul Kapus
Keyword(s):  
Internal Combustion Engine ◽  
Fuel Consumption ◽  
Urban Areas ◽  
Negative Impact ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Pollutant Emissions ◽  
Combustion Engines ◽  
Passenger Cars ◽  
And Performance

In the future, the simultaneous reduction of pollutant and CO2 emissions will require significantly enhanced powertrain functionalities that cannot only be adequately represented by the ICE (internal combustion engine) alone. Both automated transmissions and especially powertrain electrification can help to meet efficiently those extended requirements. The extended functionalities are no longer applied exclusively with the ICE itself ("Fully Flexible Internal Combustion Engine"), but distributed across the entire powertrain ("Fully Flexible Powertrain"). In addition, the powertrain will be fully networked with the vehicle environment and thus will utilize all data that are useful for emission and consumption-optimized operation of the ICE. Combustion engine and electrification often complement each other in a synergetic way. This makes it extremely sensible for the combustion engine to evolve in future from a "single fighter" to a "team player". If one compares the requirements of such an ICE with the definition of Industry 4.0, then there are extensive correspondences. Thus, it seems quite opportune to call such a fully networked combustion engine designed to meet future needs as “Internal Combustion Engine 4.0 (ICE 4.0)”. This even more so, as such a name can also be derived from the history: e.g. ICE 1.0 describes the combustion engines of the first mass-produced vehicles, ICE 2.0 the combustion engines emission-optimized since the 1960s and ICE 3.0 the highly optimized "Fully Flexible Combustion Engine", which currently offers a high torque and performance potential combined with low fuel consumption and pollutant emissions. In addition to further improvements in fuel consumption, the "Combustion Engine 4.0" offers such a low level of pollutant emissions that can best be described as "Zero Impact Emission". This means that such future ICE´s will no longer have a negative impact on the imission situation in urban areas. With the e-fuels topic, the ICE also has the potential to become both CO2- and pollutant-neutral in the medium and long term. This means that the ICE – also in passenger cars – will continue to be an essential and necessary cornerstone for future powertrain portfolios for the next decades.

scholarly journals Influence of the Use of Liquefied Petroleum Gas (LPG) Systems in Woodchippers Powered by Small Engines on Exhaust Emissions and Operating Costs

Energies ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5773 ◽  
Author(s):  
Łukasz Warguła ◽  
Mateusz Kukla ◽  
Piotr Lijewski ◽  
Michał Dobrzyński ◽  
Filip Markiewicz
Keyword(s):  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Negative Impact ◽  
Internal Combustion ◽  
Pollutant Emissions ◽  
Combustion Engines ◽  
The European Union ◽  
Liquefied Petroleum Gas ◽  
Hc Emissions ◽  
Supply Systems

The use of alternative fuels is a contemporary trend in science aimed at the protection of non-renewable resources, reducing the negative impact on people and reducing the negative impact on the natural environment. Liquefied petroleum gas (LPG) is an alternative fuel within the meaning of the European Union Directive (2014/94/UE), as it is an alternative for energy sources derived from crude oil. The use of LPG fuel in low-power internal combustion engines is one of the currently developed scientific research directions. It results from the possibility of limiting air pollutant emissions compared to the commonly used gasoline and the lower cost of this fuel in many countries. By “gasoline 95” the Authors mean non-lead petrol as a flammable liquid that is used primarily as a fuel in most spark-ignited internal combustion engines, whereas 95 is an octane rating (octane number). This article presents the results of research on fuel consumption, toxic exhaust gas emission, and operating costs of a woodchipper used for shredding branches with a diameter of up to 100 mm in real working conditions. The woodchipper, powered by a 9.5 kW internal combustion engine, fueled by gasoline and LPG was tested. Liberal regulations of the European Union (Regulation 2016/1628/EU) on the emission of harmful exhaust compounds from small spark-ignition engines (up to 19 kW) and non-road applications contribute to the low technical advancement level of these engines. The authors researched a relatively simple and cheap LPG fueling system, as in their opinion, such a system has the best chance of being implemented for use. In the study, the branches of cherry plum were shredded (Prunus cerasiferaEhrh. Beitr. Naturk. 4:17. 1789 (Gartenkalender4:189-204. 1784)). Their diameter was ca. 80 mm, length 3 m, and moisture content ca. 25%. The system was tested during the shredding of the branches in real working conditions (the frequency of supplying the branches about 4 min−1 and the mass productivity of about 0.73 t/h). Based on the recorded results, it was found that the LPG fueled engine was characterized by higher carbon monoxide (CO) and nitrogen oxides (NOx) emissions by 22% and 27%, respectively. A positive effect of using LPG was the reduction of fuel consumption by 28% and carbon dioxide (CO2) and hydrocarbons (HC) emissions by 37% and 83%, respectively. The results of the research show that the use of alternative fuels can bring benefits in terms of CO2 and HC emissions, but at the same time be characterized by an increase in CO and NOx emissions. Further research should be conducted on innovative alternative fuel supply systems, such as in the automotive industry. At the same time, legislators should limit the use of low-quality fuel supply systems with the limits of pollutant emissions in exhaust gases, contributing to the development and economic competitiveness of new fuel injection systems.

DIESEL ENGINE OPERATION IN USE OF FUEL WITH ADDITIVES

2018 ◽  
pp. 18-24
Author(s):  
Petar Kazakov ◽  
Atanas Iliev ◽  
Emil Marinov
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Experimental Studies ◽  
Combustion Engines ◽  
Engine Operation ◽  
Factors Affecting ◽  
Operating Modes ◽  
Positive Effects

Over the decades, more attention has been paid to emissions from the means of transport and the use of different fuels and combustion fuels for the operation of internal combustion engines than on fuel consumption. This, in turn, enables research into products that are said to reduce fuel consumption. The report summarizes four studies of fuel-related innovation products. The studies covered by this report are conducted with diesel fuel and usually contain diesel fuel and three additives for it. Manufacturers of additives are based on already existing studies showing a 10-30% reduction in fuel consumption. Comparative experimental studies related to the use of commercially available diesel fuel with and without the use of additives have been performed in laboratory conditions. The studies were carried out on a stationary diesel engine СМД-17КН equipped with brake КИ1368В. Repeated results were recorded, but they did not confirm the significant positive effect of additives on specific fuel consumption. In some cases, the factors affecting errors in this type of research on the effectiveness of fuel additives for commercial purposes are considered. The reasons for the positive effects of such use of additives in certain engine operating modes are also clarified.

A phenomenological model for the description of unburned hydrocarbons emission in ultra-lean engines

2021 ◽  
pp. 146808742110050
Author(s):  
Enrica Malfi ◽  
Vincenzo De Bellis ◽  
Fabio Bozza ◽  
Alberto Cafari ◽  
Gennaro Caputo ◽  
...  
Keyword(s):  
Natural Gas ◽  
Internal Combustion Engines ◽  
Pollutant Emissions ◽  
Average Error ◽  
Combustion Engines ◽  
Nitric Oxides ◽  
Lean Burn ◽  
Fuel Charge ◽  
Unburned Hydrocarbons ◽  
Model Reliability

The adoption of lean-burn concepts for internal combustion engines working with a homogenous air/fuel charge is under development as a path to simultaneously improve thermal efficiency, fuel consumption, nitric oxides, and carbon monoxide emissions. This technology may lead to a relevant emission of unburned hydrocarbons (uHC) compared to a stoichiometric engine. The uHC sources are various and the relative importance varies according to fuel characteristics, engine operating point, and some geometrical details of the combustion chamber. This concern becomes even more relevant in the case of engines supplied with natural gas since the methane has a global warming potential much greater than the other major pollutant emissions. In this work, a simulation model describing the main mechanisms for uHC formation is proposed. The model describes uHC production from crevices and flame wall quenching, also considering the post-oxidation. The uHC model is implemented in commercial software (GT-Power) under the form of “user routine”. It is validated with reference to two large bore engines, whose bores are 31 and 46 cm (engines named accordingly W31 and W46). Both engines are fueled with natural gas and operated with lean mixtures (λ > 2), but with different ignition modalities (pre-chamber device or dual fuel mode). The engines under study are preliminarily schematized in the 1D simulation tool. The consistency of 1D engine schematizations is verified against the experimental data of BMEP, air flow rate, and turbocharger rotational speed over a load sweep. Then, the uHC model is validated against the engine-out measurements. The averaged uHC predictions highlight an average error of 7% and 10 % for W31 and W46 engines, respectively. The uHC model reliability is evidenced by the lack of need for a case-dependent adjustment of its tuning constants, also in presence of relevant variations of both engine load and ring pack design.

scholarly journals The Effect of Pure Oxygenated Biofuels on Efficiency and Emissions in a Gasoline Optimised DISI Engine

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3908
Author(s):  
Tara Larsson ◽  
Senthil Krishnan Mahendar ◽  
Anders Christiansen-Erlandsson ◽  
Ulf Olofsson
Keyword(s):  
Internal Combustion Engines ◽  
Negative Impact ◽  
The Other ◽  
Nox Emissions ◽  
Combustion Engines ◽  
Engine Efficiency ◽  
Spark Timing ◽  
Low Load ◽  
Oxygenated Fuels ◽  
Load Conditions

The negative impact of transport on climate has led to incentives to increase the amount of renewable fuels used in internal combustion engines (ICEs). Oxygenated, liquid biofuels are promising alternatives, as they exhibit similar combustion behaviour to gasoline. In this article, the effect of the different biofuels on engine efficiency, combustion propagation and emissions of a gasoline-optimised direct injected spark ignited (DISI) engine were evaluated through engine experiments. The experiments were performed without any engine hardware modifications. The investigated fuels are gasoline, four alcohols (methanol, ethanol, n-butanol and iso-butanol) and one ether (MTBE). All fuels were tested at two speed sweeps at low and mid load conditions, and a spark timing sweep at low load conditions. The oxygenated biofuels exhibit increased efficiencies, even at non-knock-limited conditions. At lower loads, the oxygenated fuels decrease CO, HC and NOx emissions. However, at mid load conditions, decreased volatility of the alcohols leads to increased emissions due to fuel impingement effects. Methanol exhibited the highest efficiencies and significantly increased burn rates compared to the other fuels. Gasoline exhibited the lowest level of PN and PM emissions. N-butanol and iso-butanol show significantly increased levels of particle emissions compared to the other fuels.

The Use of Short-Term Compressed Air Supercharging in a Combustion Engine with Spark Ignition

2021 ◽  
Vol 18 (2) ◽  
pp. 8704-8713
Author(s):  
Jarosław Janusz Mamala ◽  
K. Praznowski ◽  
S. Kołodziej ◽  
G. Ligus
Keyword(s):  
Driving Force ◽  
Negative Impact ◽  
Combustion Engine ◽  
Spark Ignition ◽  
Compressed Air ◽  
Acceleration Process ◽  
Combustion Engines ◽  
Short Term ◽  
Drive Unit ◽  
The People

The powertrain is a very important subassembly in a car and is responsible not only for the automotive industry’s impact on the environment but also for the safety of people travelling by car and performing overtaking manoeuvres and joining traffic. In general, the powertrain is a combination of the drive unit and drive transmission, wherein the drive unit is responsible for the available driving force in the car’s wheels and for the car’s ability to accelerate when the throttle pedal is rapidly pressed at a constant gearbox ratio. The availability of the driving force reserve in the powertrain is the most important issue for the reason of safety of the people travelling by car. In the case of drive unit what they are of the combustion engines, the rapid pressing of the throttle pedal in the car acceleration process leads to a temporary deficiency in the driving force and in the powertrain’s output. The deficiency in the driving force has a negative impact on acceleration and driving comfort. In this paper, the authors assessed and analysed two different short-term compressed air supercharging systems for combustion engines with air supplied from a high-pressure tank. The analysis covered the response of the combustion engine with spark ignition to the gradual increase in pressure in the air-intake system. The assumption is that the applied short-term compressed air supercharging system could improve the driving force during the phase of the engine’s increasing crankshaft rotational speed. This helps to achieve the improved passenger car acceleration dynamics, depending on the supercharging method and throttle pedal exertion. When analysing the car’s acceleration dynamics, expressed by the shorter time of increasing the longitudinal speed from initial to final, it was possible to shorten the acceleration time. It is also possible to observe an improved driving force behaviour, especially during the first phase of acceleration.

Design and Operation of a Hybrid CCHP System Including PV-Wind Devices

2013 ◽  
Author(s):  
J. L. Wang ◽  
J. Y. Wu ◽  
C. Y. Zheng
Keyword(s):  
Fuel Consumption ◽  
Internal Combustion Engines ◽  
High Efficiency ◽  
Waste Heat ◽  
Internal Combustion ◽  
Energy System ◽  
Optimal Operation ◽  
Combustion Engines ◽  
Wind System ◽  
Fuel Price

CCHP systems based on internal combustion engines have been widely accepted as efficient distributed energy resources systems. CCHP systems can be efficient mainly because that the waste heat of engines can be recovered and used. If the waste heat is not used, CCHP systems may not be beneficial choices. PV-wind systems can generate electricity without fuel consumption, but the electric output depends on the weather, which is not reliable. A PV-wind system can be integrated into a CCHP system to form a higher efficient energy system. Actually, a hybrid energy system based on PV-wind devices and internal combustion engines has been studied by many researchers. But the waste heat of the engine is seldom considered in the previous work. Researches show that, 20∼30% energy can be converted into electricity by a small size engine while more than 70% is released. If the waste heat is not recovered, the system cannot reach a high efficiency. This work aims to analyze a hybrid CCHP system with PV-wind devices. Internal combustion engines are the prime movers whose waste heat is recovered for house heating or driving absorption chillers. PV-wind devices are added to reduce the fuel consumption and total cost. The optimal design method and optimal operation strategy are proposed basing on hourly analyses. Influences of the device cost and fuel price on the optimal dispatch strategies are discussed. Results show that all of the excess energy from the PV-wind system is not worth being stored by the battery. The hybrid CCHP system can be more economical and higher efficient in the studied case.

Development of the Control and Acquisition System for a Natural-Gas Spark-Ignition Engine Test Bench

2019 ◽  
Author(s):  
Lorenzo Gasbarro ◽  
Jinlong Liu ◽  
Christopher Ulishney ◽  
Cosmin E. Dumitrescu ◽  
Luca Ambrogi ◽  
...  
Keyword(s):  
Natural Gas ◽  
Internal Combustion Engines ◽  
Test Bench ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Acquisition System ◽  
Combustion Engines ◽  
Engine Test ◽  
New Sensors

Abstract Investigations using laboratory test benches are the most common way to find the technological solutions that will increase the efficiency of internal combustion engines and curtail their emissions. In addition, the collected experimental data are used by the CFD community to develop engine models that reduce the time-to-market. This paper describes the steps made to increase the reliability of engine experiments performed in a heavy-duty natural-gas spark-ignition engine test-cell such as the design of the control and data acquisition system based on Modbus TCP communication protocol. Specifically, new sensors and a new dynamometer controller were installed. The operation of the improved test bench was investigated at several operating conditions, with data obtained at both high- and low-sampling rates. The results indicated a stable test bench operation.

Sign in / Sign up

Export Citation Format

Share Document