Study on fatigue strength of SnSb11Cu6 babbitt-steel bimetal sliding bearing material prepared by MIG brazing

2020 ◽  
Vol 21 (1) ◽  
pp. 106
Author(s):  
Xinbo Wang ◽  
Zhongwei Yin ◽  
Yonghong Chen
Keyword(s):  
Fatigue Strength ◽  
Internal Combustion Engines ◽  
Centrifugal Casting ◽  
Test Method ◽  
Engineering Practice ◽  
Test Machine ◽  
Test Results ◽  
Bearing Material ◽  
Sliding Bearing ◽  
Bearing Materials

The babbitt-steel bimetal sliding bearing material prepared by the MIG brazing has been applied in many fields. In the application, usually only the bonding force is tested, and the fatigue strength is not evaluated. For this reason, this study referred to the test method for the fatigue strength of bearing materials of internal combustion engines, used the sapphire test machine (Dana Glacier Vandervell Bearings, UK) to inspect the SnSb11Cu6 babbitt-steel bimetal material prepared by MIG brazing, and analyzed the test results in depth. The test results show that, the fatigue strength of the bimetal material is more than 40 MPa. In comparison, according to the same test method and conditions on the same sapphire test machine, the fatigue strength of the SnSb11Cu6 babbitt-steel bimetal bearing material obtained by the centrifugal casting method after optimizing process was usually around 35 MPa. Therefore, the MIG brazing could produce higher fatigue strength for SnSb11Cu6 babbitt-steel bimetal bearing material. In addition, in this study, the process of fatigue failure was usually that after the microcracks were generated on the surface, they expanded to the inside of the lining, thereby resulting in spalling. This study has guiding significance for engineering practice and scientific research.

scholarly journals Hopkinson rod test results and constitutive description of TRIP780 steel resistance spot welding material

Open Physics ◽  
2020 ◽  
Vol 18 (1) ◽  
pp. 961-967
Author(s):  
Xiaomin Li ◽  
Jianrong Zhang
Keyword(s):  
Spot Welding ◽  
Steel Strip ◽  
Strain Curve ◽  
Test Machine ◽  
Strain Rates ◽  
Test Results ◽  
Welding Material ◽  
Static Tensile ◽  
Split Hopkinson ◽  
Brittle Fractures

Abstract A quasi-static tensile test was performed on a 1.4 mm-thick TRIP780 steel strip with welding points. An MTS810 material test machine was used in the test, and a Split Hopkinson tension bar device was used in performing impact stretch loading at different strain rates. The dynamic tensile stress–strain curve of the spot welding material with different strain rates was obtained through the finely designed Hopkinson rod test, and the strain rate dependence of a TRIP780 steel spot welding material was discussed. According to the dynamic constitutive equation of the TRIP780 steel spot welding material, the test results were numerically simulated, the constitutive description and test curves were compared, and the simulation results and test results were discussed and analyzed. The fractures of the test recovery specimen were scanned with the scanning electron microscope, and the fracture mechanism of the TRIP780 steel spot welding material was explored by observing the fractures. The surfaces of the fractures surface showed obvious cleavage river patterns, and the evolution process of microcracks was determined and used in characterizing brittle fractures in specimen spot welding sample subjected to dynamic stretch loading.

Experimental and analytical investigation on the in-plane dynamic instability of arches owing to parametric resonance

2017 ◽  
Vol 24 (19) ◽  
pp. 4419-4432 ◽  
Author(s):  
Airong Liu ◽  
Zhicheng Yang ◽  
Hanwen Lu ◽  
Jiyang Fu ◽  
Yong-Lin Pi
Keyword(s):  
Parametric Resonance ◽  
Dynamic Instability ◽  
Damping Ratio ◽  
Analytical Investigation ◽  
Engineering Practice ◽  
Test Results ◽  
Periodic Load ◽  
Shallow Arches ◽  
Excitation Frequencies ◽  
Critical Regions

When an arch is subjected to a periodic load, it may lose in-plane stability dynamically owing to parametric resonance. Previous investigations have been concentrated on in-plane dynamic buckling of pin-ended shallow arches. However, in engineering practice, fixed arches with different rise-to-span ratios are often encountered. Little research on in-plane dynamic instability of deep fixed arches has been reported in the literature. This paper is concerned with experimental and analytical investigations for in-plane dynamic instability of fixed circular arches with rise-to-span ratios 1/8–1/2 under a central periodic load owing to parametric resonance. Experiments are carried out to determine the in-plane frequency and damping ratio of arches, to investigate critical regions of frequencies and amplitudes of the periodic load for in-plane dynamic instability of arches, and to explore effects of the rise-to-span ratio and additional weights on dynamic instability. The analytical method for determining the region of excitation frequencies and amplitudes of the periodic load causing in-plane instability of the arch is established using the Hamilton’s principle by accounting for effects of additional concentrated weights. Comparisons of analytical solutions with test results show that they agree with each other quite well. These results show that the rise-to-span ratio significantly influences the bandwidth of regions of critical excitation frequencies for in-plane dynamic instability of arches. The critical frequencies of the periodic load and their bandwidth increase with a decrease of the rise–span ratio of the arch, whereas the corresponding amplitude of the periodic load decreases at the same time. It is also found that the central concentrated weight influences in-plane dynamic instability of arches significantly. As the weight increases, the critical frequencies of excitation and their bandwidth for in-plane dynamic instability of arches decreases, whereas the corresponding amplitude of excitation increases.

The Research of IC Test Based on LTX-77 Test System

2014 ◽  
Vol 496-500 ◽  
pp. 1176-1179
Author(s):  
Li Tan ◽  
Yu Fang
Keyword(s):  
Test Object ◽  
Test System ◽  
Test Method ◽  
Test Results ◽  
Analog Ic ◽  
Test Platform ◽  
Logic Functions ◽  
Actual Test ◽  
Ic Test

LTX-77 test system is a large IC test system that is used for various kinds of analog IC, digital IC and analog digital mixed IC. It can be used to test DC parameters, AC parameters and logic functions. In the paper, the IC test platform is LTX-77 test system. IC ADC0804 was tested as the test object. The test method of IC is described in the view of actual test. The test results show that the test system is convenient and accurate, which has important practical value for IC manufacturers and users.

scholarly journals Fatigue Strength Analysis of S34MnV Steel by Accelerated Staircase Test

2020 ◽  
Vol 10 (1) ◽  
pp. 394-400 ◽  
Author(s):  
I. M. W. Ekaputra ◽  
Rando Tungga Dewa ◽  
Gunawan Dwi Haryadi ◽  
Seon Jin Kim
Keyword(s):  
Standard Deviation ◽  
Fatigue Strength ◽  
Fatigue Limit ◽  
Fatigue Testing ◽  
Reliability Estimation ◽  
Test Method ◽  
Strength Analysis ◽  
Staircase Method ◽  
Staircase Test ◽  
Number Of Cycles

AbstractThis paper presents the reliability estimation of fatigue strength of the material used for crank throw components. The material used for crank throw components is forged S34MnV steel and subsequently heat-treated by normalising and tempering. High cycle fatigue testing under fully reversed cycling (R = −1) was performed to determine the fatigue limit of the material. The staircase test method is used to obtain accurate values of the mean fatigue limit stress until a number of cycles up to 1E7 cycles. Subsequently, the fatigue test results depend strongly on the stress step and are evaluated by the Dixon-Mood formula. The values of mean fatigue strength and standard deviation predicted by the staircase method are 282 MPa and 10.6MPa, respectively. Finally, the reliability of the design fatigue strength in some selected probability of failure is calculated. Results indicate that the fatigue strength determined from accelerated staircase test is consistent with conventional fatigue testing. Furthermore, the proposed method can be applied for the determination of fatigue strength and standard deviation for design optimisation of S34MnV steel.

The Improved Friction Properties of Bonded MoS2 Films by MAO Treating of Al Substrate

2013 ◽  
Vol 275-277 ◽  
pp. 1911-1914 ◽  
Author(s):  
Han Jun Hu ◽  
Hui Zhou ◽  
Yu Gang Zheng ◽  
Kai Feng Zhang ◽  
Zhi Hua Wan
Keyword(s):  
Tribological Properties ◽  
Solid Lubricants ◽  
Ceramic Coatings ◽  
Test System ◽  
Test Method ◽  
Test Results ◽  
Specimen Test ◽  
Micro Arc Oxidation ◽  
A New Technique ◽  
Porous Microstructures

The bonded MoS2 films are widely used as solid lubricants in aerospace mechanisms due to their excellent tribological properties. Traditionally, the MoS2 was directly bonded on the Al substrate that was only treated by the technique named of sandblast. For improving the tribological properties of MoS2 films, micro arc oxidation (MAO) instead of sandblast was introduced as a new technique for treating of Al substrate. In this article, the tribological properties of MoS2 films which were bonded on different surface of Al substrate as mentioned above were discussed, respectively. It was concluded from the test results that the MoS2 films bonded on substrate treated by MAO have better tribological properties than those samples treated by sandblast. The endurance life against abrasion of the former is as high as twenty times of the latter by the stand test method of ball on disk using the UMT Multi-Specimen Test System. This test results could be illustrated by the following reasons. The first is the porous microstructures of MAO ceramic coatings on the Al substrate. The coatings have numerous pits to be good at increasing the binding force with the MoS2 films, and the pits can also provide a MoS2 lubricants reservoir during processes of friction. Both of them improved the MoS2 film’s ability of wear-protective. The second is that hardness of the coating is higher than the Al, and this ensures well wearing resistance, especially in practical application to big load-supporting moving parts, such as bearing, gear, etc…

Study on Conventional Domed Bursting Disc Material and Burst Pressure Test

2013 ◽  
Vol 690-693 ◽  
pp. 2371-2378
Author(s):  
Wei Pu Xu ◽  
Yi Ting Liu
Keyword(s):  
Stainless Steel ◽  
Tensile Test ◽  
316L Stainless Steel ◽  
Performance Test ◽  
Test Method ◽  
Burst Pressure ◽  
Test Results ◽  
Manufacturing Method ◽  
Pressure Test ◽  
Disc Material

A brief overview is given in the conventional domed bursting disc structure and manufacturing method. 316L stainless steel as a template is selected. With the investigation on bursting disc material tensile test method, the test results are summarized,also the burst results of disc burst pressure in different sizes. With the help of bursting disc material performance test and bursting disc burst pressure test of 316L , the test results provide a reference for other types of bursting disc.

scholarly journals Hedonic Test Method for Measuring Instant Pindang Seasoning Powder Preferences

2019 ◽  
Vol 3 (1) ◽  
pp. 34
Author(s):  
Dea Tio Mareta
Keyword(s):  
Test Method ◽  
Test Results ◽  
Drying Method ◽  
Typical Food ◽  
Hedonic Scale

Instant seasoning for cooking are commonly known by people who want something practical. Pindang is a typical food of Lampung and South Sumatra Province, consisting of various spices and herbs. Instant pindang seasoning powder made with foam mat drying method using 3 varations of foam additives. The purpose of this study was to determine the level of taste, aroma, and color of instant pindang seasoning powder made with three variations of foam additives, namely 5% (w/w), 10% (w/w), and 15% (w/w). The hedonic test for instant pindang seasoning powder were carried out on 35 panelists. Panelists were faced with 3 samples with 3 different sample numbers. Panelists were asked to assess how much preference for seasoning products using hedonic scale. The hedonic test results showed that, with the addition of 15% (w/w) foam is preferred in terms of color. As for aroma and taste, there were no significant differences between the three products. Keywords: foam mat drying , hedonic test, instant pindang seasoning powder, pindang

scholarly journals Pengaruh Latihan Dribbling With A Curving Line Trajectory Untuk Meningkatkan Keterampilan Dribbling Pemain Sepak Bola Ps. Undikam Mataram Tahun 2019

2019 ◽  
Vol 4 (4) ◽  
Author(s):  
Ismail Marzuki ◽  
Soemardiawan Soemardiawan
Keyword(s):  
Sampling Technique ◽  
Test Method ◽  
Soccer Players ◽  
Football Players ◽  
Test Results ◽  
Significance Level ◽  
Speed Test ◽  
Table Analysis ◽  
Observation Method ◽  
Line Trajectory

The focus of the problem in this research When competing frequently there are mistakes in dribbling, so from this it is necessary to have this exercise, to improve the dribbling skills of PS players. UNDIKMA Mataram. The purpose of this study is to determine whether there is an effect of Dribbling With A Curving Line Trajectory Exercise on the Dribbling Skills of PS Soccer Players. Mataram UNDIKMA 2019 ". The research methods used by researchers are the observation method, the documentation method and the deed test method. The study design uses a pretest-posttest design (initial test and final test). The population used in this study are all PS players. UNDIKMA Mataram in 2019. The number of samples in the study conducted was 22 which became a sample of 11 players PS soccer players. UNDIKMA Mataram. The sampling technique in this study using the saturation sampling technique is a sampling technique if all members of the population can be sampled. Analysis of statistical data with a significance level of 5% for the speed test results obtained by the t-value so from the results of research X1 (Dribbling With A Curving Line Trajectory, with Y1 obtained tcount is much greater than ttable, this shows that the hypothesis "Ha" (accepted ) then this research is significant, drawing conclusions from the table analysis at a significant level of 5% with a number of samples (n - 1) that is 11-1 = 10 at 1,812. Then it can be concluded that, 1) The Effect of Dribbling With A Curving Line Trajectory on Dribbling Skills PS Football Players. Mataram UNDIKMA 2019, Tcount> ttable (7.362> 1,812). 2). this shows that the hypothesis "Ha" (accepted) then this research is significant.

scholarly journals PENDIDIKAN KARAKTER MELALUI PEMBELAJARAN MATEMATIKA

2014 ◽  
Vol 10 (1) ◽  
Author(s):  
Salafudin *
Keyword(s):  
Statistical Analysis ◽  
Character Education ◽  
Sampling Technique ◽  
Problem Formulation ◽  
Test Method ◽  
Cluster Sampling ◽  
Test Results ◽  
Learning Mathematics ◽  
Character Building ◽  
Better Than

This study aimed to determine: (1) how was the design of character building by learning mathematics, and (2) whether the character building by learning mathematics could produce better learning outcome of mathematics than conventional mathematics learning.To answer these two questions, I used Research and Development ( R & D ) which consists of a preliminary study to obtain preliminary data on student learning outcomes before being given treatments of character building by learning mathematics. The next phase is the design of the character building by learning mathematics. Further testing and revision in class and repeated until it found the best learning model. From the first problem formulation, qualitative data analysis, such as the design of character building in learning mathematics was produced. The results of the qualitative analysis shows, character building by learning mathematics was quite effectively applied to implant positive character in students. To answer the second question, statistical analysis was used. The population in this study was all students of class VII of MTsN in Buaran of Pekalongan which totaled 220. By random cluster sampling technique two classes (a class VII A and VII B) was chosen. Class VII A was as an experiment class, and class VII B was as a control class. Data were taken by the test method, experimental classroom observation, and documentation. The data was then processed with an average difference test. Results of statistical analysis obtained t = 3.33 > t table = 1.67. This meant that learning achievement of the students in the experimental class, which was implemented character education in mathematics was better than the students who were taught by conventional methods. Based on these results, it could be conclude that the character building in mathematics was better than the conventional method of learning mathematics.

Sign in / Sign up

Export Citation Format

Share Document