scholarly journals A NEW EPOXY EMBEDMENT FOR ELECTRON MICROSCOPY

1962 ◽  
Vol 13 (3) ◽  
pp. 437-443 ◽  
Author(s):  
James A. Freeman ◽  
Ben O. Spurlock

A new epoxy embedding mixture has been developed utilizing Maraglas 655 and Cardolite NC-513 with benzyldimethylamine (BDMA) as a curing agent. This epoxy mixture permits cellular preservation comparable to that obtained with Epon 812, ease of preparation of tissues, a wide range of miscibility, low viscosity, and, most important, ease of sectioning on a Porter-Blum microtome. In contrast to Epon-812-embedded tissues, Maraglas-Cardolite-embedded tissues can be sectioned in large dimensions with ease and consistent results without "chatter." No background granularity is detectable with high magnification study of Maraglas-Cardolite-embedded tissues. This epoxy is readily stained with lead hydroxide and is relatively stable in the electron beam.

1994 ◽  
Vol 2 (4) ◽  
pp. 21-22
Author(s):  
Donald P. Cox

Successful immunolabeling in electron microscopy of animal and plant tissues requires a combination of excellent antigen preservation while maintaining the original structure of the tissue. One important element is tissue embedding which accomplishes two goals for the immunohistochemist, the preservation of tissue specimen structure and maintenance of biological antigenicity. Tissue embedding in plastic resins is a common method in which several important elements must be considered.1.Fine tissue structure must not be damaged by the polymerization.2.The plastic must be stable to the electron beam.3.Light scattering properties of the plastic should be minimal.4.The plastic should cut easily.5.The plastic must be of sufficiently low viscosity to infiltrate the tissue.


Author(s):  
Hilton H. Mollenhauer

There are several factors that were requisites for the biological applications of electron microscopy. One of these was, clearly, the development of a matrix substance that could infiltrate biological material and encapsulate tissue components so that they could be thin sectioned and examined under an electron beam. Without such matrix substances, examination of tissue as we know it today, would not be possible.Perhaps the start of practical electron microscopy in the context stated above was the application of methacrylate resins for tissue embedment. Methacrylates have a very low viscosity and maintain this viscosity until polymerization is initiated (for days or weeks if one should wish). The two most commonly used methacrylates were n-butyl (soft) and n-methyl (hard) which could be mixed in various proportions to yield almost any block hardness. Methacrylates can be cross-linked with divinyl benzene to improve stability but this was not commonly done. Methacrylates are very easy to section which was an important aspect at the time since sectioning had to be done with glass knives.


1968 ◽  
Vol 21 (3) ◽  
pp. 325 ◽  
Author(s):  
P Humble

The method of computation of electron microscope images developed by Head (1967) produces micrographs of single dislocations in about 1 min of numerical integration. In Head's original programme, the electron beam direction and the normal to the foil surface are coincident. Since this condition is not often realized in practical electron microscopy, the programme has been extended to compute the images of dislocations in tilted foils. It has been further modified to compute he images from a configuration 'containing up to two dislocations and up to three stacking faults. These programmes are thus applica.ble to a wide range of defect con� figurations in tilted thin foils. The derivation of these programmes is described and several examples of their- use in experimental situations are given. These include the "skewing" of dislocation images due to the noncoincidence of the beam direction and the foil normal, and images due to interactions between dislocations and stacking faults.


Author(s):  
G. G. Shaw

The morphology and composition of the fiber-matrix interface can best be studied by transmission electron microscopy and electron diffraction. For some composites satisfactory samples can be prepared by electropolishing. For others such as aluminum alloy-boron composites ion erosion is necessary.When one wishes to examine a specimen with the electron beam perpendicular to the fiber, preparation is as follows: A 1/8 in. disk is cut from the sample with a cylindrical tool by spark machining. Thin slices, 5 mils thick, containing one row of fibers, are then, spark-machined from the disk. After spark machining, the slice is carefully polished with diamond paste until the row of fibers is exposed on each side, as shown in Figure 1.In the case where examination is desired with the electron beam parallel to the fiber, preparation is as follows: Experimental composites are usually 50 mils or less in thickness so an auxiliary holder is necessary during ion milling and for easy transfer to the electron microscope. This holder is pure aluminum sheet, 3 mils thick.


Author(s):  
R.W. Horne

The technique of surrounding virus particles with a neutralised electron dense stain was described at the Fourth International Congress on Electron Microscopy, Berlin 1958 (see Home & Brenner, 1960, p. 625). For many years the negative staining technique in one form or another, has been applied to a wide range of biological materials. However, the full potential of the method has only recently been explored following the development and applications of optical diffraction and computer image analytical techniques to electron micrographs (cf. De Hosier & Klug, 1968; Markham 1968; Crowther et al., 1970; Home & Markham, 1973; Klug & Berger, 1974; Crowther & Klug, 1975). These image processing procedures have allowed a more precise and quantitative approach to be made concerning the interpretation, measurement and reconstruction of repeating features in certain biological systems.


Author(s):  
Edward D. De-Lamater ◽  
Eric Johnson ◽  
Thad Schoen ◽  
Cecil Whitaker

Monomeric styrenes are demonstrated as excellent embedding media for electron microscopy. Monomeric styrene has extremely low viscosity and low surface tension (less than 1) affording extremely rapid penetration into the specimen. Spurr's Medium based on ERL-4206 (J.Ultra. Research 26, 31-43, 1969) is viscous, requiring gradual infiltration with increasing concentrations. Styrenes are soluble in alcohol and acetone thus fitting well into the usual dehydration procedures. Infiltration with styrene may be done directly following complete dehydration without dilution.Monomeric styrenes are usually inhibited from polymerization by a catechol, in this case, tertiary butyl catechol. Styrene polymerization is activated by Methyl Ethyl Ketone peroxide, a liquid, and probably acts by overcoming the inhibition of the catechol, acting as a source of free radical initiation.Polymerization is carried out either by a temperature of 60°C. or under ultraviolet light with wave lengths of 3400-4000 Engstroms; polymerization stops on removal from the ultraviolet light or heat and is therefore controlled by the length of exposure.


Author(s):  
J. G. Adams ◽  
M. M. Campbell ◽  
H. Thomas ◽  
J. J. Ghldonl

Since the introduction of epoxy resins as embedding material for electron microscopy, the list of new formulations and variations of widely accepted mixtures has grown rapidly. Described here is a resin system utilizing Maraglas 655, Dow D.E.R. 732, DDSA, and BDMA, which is a variation of the mixtures of Lockwood and Erlandson. In the development of the mixture, the Maraglas and the Dow resins were tested in 3 different volumetric proportions, 6:4, 7:3, and 8:2. Cutting qualities and characteristics of stability in the electron beam and image contrast were evaluated for these epoxy mixtures with anhydride (DDSA) to epoxy ratios of 0.4, 0.55, and 0.7. Each mixture was polymerized overnight at 60°C with 2% and 3% BDMA.Although the differences among the test resins were slight in terms of cutting ease, general tissue preservation, and stability in the beam, the 7:3 Maraglas to D.E.R. 732 ratio at an anhydride to epoxy ratio of 0.55 polymerized with 3% BDMA proved to be most consistent. The resulting plastic is relatively hard and somewhat brittle which necessitates trimming and facing the block slowly and cautiously to avoid chipping. Sections up to about 2 microns in thickness can be cut and stained with any of several light microscope stains and excellent quality light photomicrographs can be taken of such sections (Fig. 1).


Author(s):  
M. A. Hayat

Potassium permanganate has been successfully employed to study membranous structures such as endoplasmic reticulum, Golgi, plastids, plasma membrane and myelin sheath. Since KMnO4 is a strong oxidizing agent, deposition of manganese or its oxides account for some of the observed contrast in the lipoprotein membranes, but a good deal of it is due to the removal of background proteins either by dehydration agents or by volatalization under the electron beam. Tissues fixed with KMnO4 exhibit somewhat granular structure because of the deposition of large clusters of stain molecules. The gross arrangement of membranes can also be modified. Since the aim of a good fixation technique is to preserve satisfactorily the cell as a whole and not the best preservation of only a small part of it, a combination of a mixture of glutaraldehyde and acrolein to obtain general preservation and KMnO4 to enhance contrast was employed to fix plant embryos, green algae and fungi.


Author(s):  
T. Ichinokawa ◽  
H. Maeda

I. IntroductionThermionic electron gun with the Wehnelt grid is popularly used in the electron microscopy and electron beam micro-fabrication. It is well known that this gun could get the ideal brightness caluculated from the Lengumier and Richardson equations under the optimum condition. However, the design and ajustment to the optimum condition is not so easy. The gun has following properties with respect to the Wehnelt bias; (1) The maximum brightness is got only in the optimum bias. (2) In the larger bias than the optimum, the brightness decreases with increasing the bias voltage on account of the space charge effect. (3) In the smaller bias than the optimum, the brightness decreases with bias voltage on account of spreading of the cross over spot due to the aberrations of the electrostatic immersion lens.In the present experiment, a new type electron gun with the electrostatic and electromagnetic lens is designed, and its properties are examined experimentally.


Author(s):  
Joseph J. Comer ◽  
Charles Bergeron ◽  
Lester F. Lowe

Using a Van De Graaff Accelerator thinned specimens were subjected to bombardment by 3 MeV N+ ions to fluences ranging from 4x1013 to 2x1016 ions/cm2. They were then examined by transmission electron microscopy and reflection electron diffraction using a 100 KV electron beam.At the lowest fluence of 4x1013 ions/cm2 diffraction patterns of the specimens contained Kikuchi lines which appeared somewhat broader and more diffuse than those obtained on unirradiated material. No damage could be detected by transmission electron microscopy in unannealed specimens. However, Dauphiné twinning was particularly pronounced after heating to 665°C for one hour and cooling to room temperature. The twins, seen in Fig. 1, were often less than .25 μm in size, smaller than those formed in unirradiated material and present in greater number. The results are in agreement with earlier observations on the effect of electron beam damage on Dauphiné twinning.


Sign in / Sign up

Export Citation Format

Share Document