scholarly journals Effect of Limestone Powder on Mechanical Properties of Engineering Cementitious Composites

2021 ◽  
Vol 2076 (1) ◽  
pp. 012082
Author(s):  
Jianwei Zhou ◽  
Baoying Yu ◽  
Yaning Kong ◽  
Wen Yang ◽  
Baojun Cheng
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Flexural Strength ◽  
Water Demand ◽  
Limestone Powder ◽  
Partial Replacement ◽  
Cementitious Composites ◽  
Replacement Ratio ◽  
Complete Replacement ◽  
Lime Powder

Abstract The effect of limestone powder replacing fly ash on the mechanical properties of engineering cementitious composites was investigated. The results showed that the water demand of engineering cementitious composites due to partial replacement of fly ash by limestone powder, but the water demand of the system decreased when the replacement ratio reached 100%. The flexural strength of the specimen appears to decrease with increasing age due to incomplete replacement of lime powder. The toughness of the specimen can be significantly improved due to the complete replacement of fly ash by limestone powder.

scholarly journals Flexural resistance of the polypropylene fibres reinforced cement mixes with waste material

2019 ◽  
Vol 281 ◽  
pp. 01010
Author(s):  
Samer Abou Kheir ◽  
Jad Wakim ◽  
Elie Awwad
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Flexural Strength ◽  
Waste Product ◽  
Waste Material ◽  
Sustainable Construction ◽  
Partial Replacement ◽  
Polypropylene Fibres ◽  
Ground Support ◽  
Reinforced Cement

The polypropylene (PP) fibers in shotcrete has been used for ground support and building strengthening, since several decades. However, the recent trend is to use the waste material in cementbased mixes to produce an eco-friendly material. Such waste material is the incineration fly ash (FA) that is classified as a hazardous product. This study is intended to establish the mechanical properties of fiber reinforced mortar in addition to cement or sand partial replacement by fly ash, in terms of flexural strength testing. The mechanical properties reflect the influence of the dosage of fiber content and the proportion of the fly ash on the flexural strength. The percentage of cement or sand was replaced by 0, 10, 20, and 30% fly ash. The dosage of fibers was 0, 0.6, 1.2, and 1.8 kg/m3. This green mix with fibers provides a partial substitute of cement as it is cheaper, by incorporating waste product, and saving energy consumption in the production. Due to growing interest in sustainable construction, engineers and architects are motivated to choose such materials which are more sustainable.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

Physical and Mechanical Properties of Cement Paste Were Used Partially with Fly Ash and Kaolin Waste

2017 ◽  
Vol 866 ◽  
pp. 199-203
Author(s):  
Chidchanok Chainej ◽  
Suparut Narksitipan ◽  
Nittaya Jaitanong
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lime Water ◽  
Diffraction Patterns ◽  
Iron Mold

The aims of this research were study the microstructures and mechanical properties for partial replacement of cement with Fly ash (FA) and kaolin waste (KW). Ordinary Portland cement were partially replaced with FA and KW in the range of 25-35% and 10-25% by weight of cement powder. The kaolin waste was ground for 180 minutes before using. The specimen was packing into an iron mold which sample size of 5×5×5 cm3. Then, the specimens were kept at room temperature for 24 hours and were moist cured in the incubation lime water bath at age of 3 days. After that the specimens were dry cured with plastic wrap at age of 3, 7, 14 and 28 days. After that the compounds were examined by x-ray diffraction patterns (XRD) and the microstructures were examined by scanning electron microscopy (SEM). The compressive strength was then investigated.

Influence of Different Mineral Precursors on the Properties of Fly Ash Based Alkali-Activated Mortars

2018 ◽  
Vol 761 ◽  
pp. 73-78 ◽  
Author(s):  
Matej Špak ◽  
Pavel Raschman
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Chemical Composition ◽  
Coal Combustion ◽  
Pure Aluminum ◽  
Partial Replacement ◽  
Black Coal ◽  
Fly Ashes ◽  
Final Composition ◽  
Alkali Activated

Alkali-activated materials based on fly ash are widely developed and also produced on the present. Some of fly ashes are not suitable for production of alkali-activated materials because of their inconvenient chemical composition. Alumina-silicates are the most important components that are needed to accomplish the successful reaction. The proper content of amorphous phase of alumina-silicates and its proportion as well should be provided for the final composition of alkali-activated materials. The influence of pure aluminum oxide powder as well as raw milled natural perlite on mechanical properties and durability of alkali-activated mortars was investigated. These minerals were used as partial replacement of fly ash coming from black coal combustion. In addition, the mortars were prepared by using different alkali activators.

scholarly journals Microwave absorption and mechanical properties of double-layer cement-based composites containing different replacement levels of fly ash

2018 ◽  
Vol 25 (4) ◽  
pp. 707-714 ◽  
Author(s):  
Yuefang Zhang ◽  
Shunhua Liu ◽  
wanJun Hao
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Double Layer ◽  
Impedance Matching ◽  
X Ray Diffraction ◽  
Replacement Ratio ◽  
Matching Layer ◽  
Optimal Replacement ◽  
Zn Ferrite ◽  
Absorbing Layer

Abstract Double-layer absorbing cement-based composites with the thickness of 10 mm were prepared, including different replacement levels of fly ash (FA) in the absorbing layer as well as the matching layer for impedance matching. Waste polyethylene terephthalate bottle fragment was introduced as electromagnetic transparent reinforcement aggregate. Carbon black was used to be original absorbent in the absorbing layer. The microstructure and electromagnetic parameters of FA were closely looked at through scanning electron microscope, X-ray diffraction, and analyzer of vector network. The absorption and mechanical properties of cement-based composites were tested. It turned out that when the optimal replacement ratio of FA in the absorbing layer and matching layer gets to 50%:30%, the minimum value of reflection loss achieves −22.3 dB at 13.2 GHz; also, the value of absorption bandwidth that is effective (<−8 dB) is 6.4 GHz. Ni-Zn ferrite proves to be a feasible absorbent that is additional for the matching layer compared to what is added to the absorbing layer. The compressive strength of all the mixtures decreased, while the flexural strength decreased first and then increased with the rise of the FA replacement level.

scholarly journals Mechanical Properties and Microstructural Features using Stone Dust as a Partial Replacement of Sand

2019 ◽  
Vol 8 (6) ◽  
pp. 5232-5237
Keyword(s):  
Mechanical Properties ◽  
Economic Growth ◽  
Sustainable Development ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Natural Resources ◽  
Strength Test ◽  
Partial Replacement ◽  
Test Results ◽  
Stone Dust

Today’s world is always leads to development in technology as well as the economic growth though sometime these will affect the environment badly. That’s why world environmental commission coined the termed called sustainable development where development takes place without hampering the others’ needs. Concrete industry is rapidly growing industry in India which consumes lots of natural resources during the production of concrete. Here Stone dust is used as a sustainable material in place of sand partially. M25 grade of concrete has been chosen for the experiments. Different mechanical properties of concrete like compressive strength, Split tensile, flexural strength etc. and Microstructural features like SEM, EDX have been included in this study. Compressive Strength and flexural strength test results shown the increase in the strength. Sulphate Resistance Properties have been tested by curing the cubes in the MgSO4 solution and increase in weight has been observed. Similarities are found in the SEM pictures

The Behavior of FRA Concrete with High Replacement Ratio

2018 ◽  
Vol 760 ◽  
pp. 204-209 ◽  
Author(s):  
Magdaléna Šefflová
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Absorption Capacity ◽  
Recycled Aggregate ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Replacement Ratio ◽  
Natural Sand ◽  
Concrete Mixtures

This study deals with determination of the properties of the fine recycled aggregate (FRA) concrete with partial replacement of natural sand in concrete mixtures. The FRA was obtained from concrete waste and crushed on fraction 0 – 4 mm by laboratory jaw crusher. The geometrical and physical properties of natural sand and the FRA were tested. The main goal of this study is evaluation of the basic physical and mechanical properties of the concrete with partial natural sand replacement by the FRA such as workability, water absorption capacity, compressive strength and flexural strength. A total four concrete mixtures were prepared. The first concrete mixture was prepared only with natural sand, did not include the FRA. In other concrete mixtures, natural sand was replaced by the FRA in various replacement ratios (40 %, 50 %, and 60 %). All concrete mixtures were designated with the same parameters for clear comparison. The workability of fresh concrete mixtures and physical and mechanical properties of hardened concrete were tested.

Sign in / Sign up

Export Citation Format

Share Document