scholarly journals Mechanical Properties and Microstructural Features using Stone Dust as a Partial Replacement of Sand

2019 ◽  
Vol 8 (6) ◽  
pp. 5232-5237
Keyword(s):  
Mechanical Properties ◽  
Economic Growth ◽  
Sustainable Development ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Natural Resources ◽  
Strength Test ◽  
Partial Replacement ◽  
Test Results ◽  
Stone Dust

Today’s world is always leads to development in technology as well as the economic growth though sometime these will affect the environment badly. That’s why world environmental commission coined the termed called sustainable development where development takes place without hampering the others’ needs. Concrete industry is rapidly growing industry in India which consumes lots of natural resources during the production of concrete. Here Stone dust is used as a sustainable material in place of sand partially. M25 grade of concrete has been chosen for the experiments. Different mechanical properties of concrete like compressive strength, Split tensile, flexural strength etc. and Microstructural features like SEM, EDX have been included in this study. Compressive Strength and flexural strength test results shown the increase in the strength. Sulphate Resistance Properties have been tested by curing the cubes in the MgSO4 solution and increase in weight has been observed. Similarities are found in the SEM pictures

scholarly journals Pozzolanic and mechanical properties of Date Palm Seed Ash (Dpsa) concrete

2020 ◽  
Vol 39 (3) ◽  
pp. 680-686
Author(s):  
A.S.J. Smith ◽  
G. Xu ◽  
M.J. Garba ◽  
M.Y. Aliyu
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Date Palm ◽  
Activity Index ◽  
Strength Test ◽  
Partial Replacement ◽  
Test Results ◽  
Setting Times ◽  
Compressive Strength Test

This paper presents the findings of a research work conducted on how to improve the mechanical properties of concrete using Date Palm Seed Ash (DPSA) as partial replacement of cement. The DPSA used was obtained by controlled burning of date palm seed in a kiln at a maximum temperature of 630oC for eight hours and air cooled afterwards. The ash obtained was sieved through 75μm sieve and its oxide composition analysed using X-ray fluorescence (XRF) procedures. DoE method of mix design was used to produce concrete ingredients for grade 30N/mm2 giving a water-cement ratio of 0.53. The effect of partial replacement of cement with DPSA on cement paste and concrete using 0, 2.5, 5, 7.5, 10, 15 and 20% DPSA was investigated through consistency and setting times tests, workability test, compressive strength test (at 7, 21, 28 and 56 days curing duration), pozzolanic activity index evaluation and water absorption test. Results show that DPSA has high silicon dioxide (45.50%), aluminum oxide (20.75%) and Iron oxide (7.25%). Findings indicate that the consistency and setting times of cement-DPSA paste increased with increase in the replacement of cement with DPSA. The workability of DPSA concrete decreased with increase in cement replacement. Compressive strength test results show that cement can be replaced with DPSA up to 10% as the compressive strength at 10% replacement is 31.5N/mm2 as against the 31N/mm2 of the normal concrete, at 56 days. The pozzolanic activity index result also show that DPSA concrete meets up the minimum requirement of 75% specified by ASTM C618-15. Also, the water absorption capacity of DPSA concrete at the highest replacement (20%) is 11% less than that at 0%. Keywords: Cement, Compressive strength, Concrete, Date palm seed ash, Partial replacement, Pozzolana

scholarly journals Impact of Fire on Mechanical Properties of Slurry Infiltrated Fiber Concrete (SIFCON)

2020 ◽  
Vol 6 ◽  
pp. 12-23
Author(s):  
Anwar Saad Abbas ◽  
Mohammed Mansour Kadhum
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Flexural Strength ◽  
Elevated Temperatures ◽  
Partial Replacement ◽  
Test Results ◽  
Fiber Volume ◽  
Design Curve ◽  
Fire Flame

This research aims to shed light on the fire flame effect on some mechanical properties of SIFCON samples, such as compressive strength, flexural strength and modulus of elasticity and comparing the results with CEN design curve and CEB. Higher temperature resistance is one of the most important parameters affecting the durability and service life of the material. This study comprised of casting and testing SIFCON specimens with 6% fiber volume before and after exposure to elevated temperatures. Two fire exposure duration of 1 and2 hours were investigate. In addition to room temperature, Silica fume was used as a partial replacement (10%) by weight of cement. It was found from the results achieved that after exposure to high temperatures, compressive strength, flexural strength and elastic modulus decreased. The drastically reduction of compressive strength took place with increasing temperature.  The residual compressive strength, flexural strength and elastic modulus at 1010 °C were in the range of (58.4 to 80.1%), (81.6 to 78.7%) and (30.4 to 32.8%) respectively. The compressive strength test results of this study together with results obtained by other investigators were compared with CEB strength-reduction curve and that of CEN. It was noticed that the test results agreed with CEN design curve rather than with that of CEB.

scholarly journals Properties of High-Strength Flowable Mortar Reinforced with Palm Fibers

2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Mahyuddin Ramli
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Test Results ◽  
Palm Fiber ◽  
Toughness Index ◽  
Strength And Toughness

This study was conducted to determine some physical and mechanical properties of high-strength flowable mortar reinforced with different percentages of palm fiber (0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2, 1.4, and 1.6% as volumetric fractions). The density, compressive strength, flexural strength, and toughness index were tested to determine the mechanical properties of this mortar. Test results illustrate that the inclusion of this fiber reduces the density of mortar. The use of 0.6% of palm fiber increases the compressive strength and flexural strength by about 15.1%, and 16%, respectively; besides, the toughness index (I5) of the high-strength flowable mortar has been significantly enhanced by the use of 1% and more of palm fiber.

scholarly journals Mechanical Properties of Concrete Modified with Silica Fume and Integral Waterproof and Comparison with Waste Glass Aggregate Concrete

2022 ◽  
Vol 961 (1) ◽  
pp. 012082
Author(s):  
Taghreed Abd-Almahdee Musa ◽  
Hiba Ali Abbas ◽  
Ayam Jabbar Jihad
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Silica Fume ◽  
Strength Test ◽  
Waste Glass ◽  
Fine Aggregate ◽  
Glass Aggregate ◽  
Water Proof ◽  
Strength And Durability

Abstract This study includes the effect of using different dosages of integral waterproof Admixture and silica fume on some mechanical properties of concrete. Concrete improved by using different ratios of integral water proof admixture(IWP admixture) to increase strength and durability, this admixture used as percentages from cement weight in each mix ranged from 0.0% to 2% ( 0.0, 1.0%, 1.2%,1.4%,1.6%,1.8%, and 2%), compressive strength test done for cubes with (10*10*10) cm for each mix. The flexural strength test was done by (10*10*40) cm beams and tested after 28 days of curing. comparison study was made between silica fume mixes properties and mixes without silica fume. Adding IWP admixture leads to increase mechanical properties of ordinary concrete, the reference mix shows compressive strength equal to 26.38 MPa, while mixes with 2% IWP gives 38.8 MPa in this study. The study also includes the effect of using 2 main dosages of silica fume to the mixes that contain IWP, the new concrete with two admixtures show better values of compressive, tensile and flexural strength comparing with mixes with only IWP, the compressive strength increased from 38.8 MPa for ordinary IWP mixes to 52.3 MPa for 10% silica fume concrete mixes, and also the flexural strength increased from 4.8 MPa for mixes with only IWP to 7.3 MPa for mixes modified with 10 % silica fume. Study include also using waste glass as fine aggregate in mixes contain IWP and 10% silica fume and that show more increment in mechanical properties also.

Proposal of Fire Resistant Composites with Application of Lightweight Aggregate Liaver

2014 ◽  
Vol 1054 ◽  
pp. 43-47 ◽  
Author(s):  
Marcel Jogl ◽  
Pavel Reiterman ◽  
Ondřej Holčapek ◽  
Jaroslava Koťátková
Keyword(s):  
Mechanical Properties ◽  
Lightweight Aggregate ◽  
Strength Test ◽  
Partial Replacement ◽  
Test Results ◽  
Standard Laboratory ◽  
Strength Tests ◽  
Hardened Properties ◽  
Brick Dust ◽  
High Temperature Effect

This paper describes the application of lightweight aggregate (LWA) in the creation of fire resistant composite. The effort of the project is the preparation of a light refractory material with good mechanical properties, which would reach technically economical solutions. We initially chose as lightweight aggregate Liaver, which in combination with chamotte aggregate represent the filler of composite. The following observations were focused on partial replacement of binding components with brick dust and its influence on the mechanical properties of the composite. After design process, test composite specimens were produced to determine hardened properties at standard age. On the 28 day were all the mixtures exposed to 105, 600 and 1000 °C. Lastly, the flexural and compressive strength tests were performed on the composite specimens to identify high temperature effect comparing to strength test results obtained from standard laboratory conditions.

scholarly journals Impact of Incorporating Metakaolin on the Mechanical Performance of High Grade Concrete

2019 ◽  
Vol 8 (3) ◽  
pp. 7736-7739 ◽  
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Mechanical Performance ◽  
Strength Test ◽  
Strength Development ◽  
High Grade ◽  
Test Results ◽  
Normal Concrete ◽  
Split Tensile Strength ◽  
Compressive Strength Test

This paper studies the effect of incorporating metakaolin on the mechanical properties of high grade concrete. Three different metakaolins calcined at different temperature and durations were used to make concrete specimens. Three different concrete mixtures were characterized using 20% metakaolin in place of cement. A normal concrete mix was also made for comparison purpose. The compressive strength test, split tensile test and flexural strength tests were conducted on the specimens. The compressive strength test results showed that all the metakaolin incorporated concrete specimens exhibited higher compressive strength and performed better than normal concrete at all the days of curing. The rate of strength development of all the mixes was also studied. The study revealed that all the three different metakaolin incorporated mixtures had different rate of strength development for all the days of hydration (3, 7,14, 28, 56 and 90), indicating that all the metakaolins possessed different rate of pozzolanic reactivity. Further, from the analysis of the test results, it was concluded that the variation in the rate of strength development is due to the differences in the temperature and duration at which they were manufactured. The results of split tensile strength test and the flexural strength test conducted on the specimens, supported the conclusions drawn from the results of compressive strength test. The paper also discusses, the rate of development of compressive strength and the pozzolanic behaviour of the metakaolins in light of their parameters of calcination and physical properties such as amorphousness and particle size. This paper has been written with a view to make the potential of metakaolin available to the construction industry at large

scholarly journals Strength of Concrete using Clay as a Partial Replacement of Binder Content with and Without Lime

2021 ◽  
Vol 10 (3) ◽  
pp. 1-6
Author(s):  
S. B. Kandekar ◽  
◽  
S. K. Wakchaure ◽  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Hydrated Lime ◽  
Strength Test ◽  
Binder Content ◽  
Partial Replacement ◽  
Split Tensile Strength ◽  
Tensile Strength Test ◽  
Compressive Strength Test

Materials are the most important component of building construction. The demands of construction material are increasing day by day significantly. This demand is increasing the material prices and scarcity of material in construction industry. To achieve economical and eco-friendly criteria naturally occurring material is selected. Clay is a natural material and it can be available easily. This paper interprets the experimental investigation on strength of concrete using clay as a partial replacement to binder content (cement) in concrete. The replacement percentages are grouped as 0%, 10%, 20%, 30%, 40% of clay and 5% of hydrated lime with cement in each series in M25 grade of concrete. To achieve the pozzolanic property of clay hydrated lime was added. Different tests are performed to determine the optimum percentage of clay as a replacement for binder content (cement) in concrete. The Compressive strength test, split tensile strength test and flexural strength test were performed on the specimens. Total 90 cubes of size 150 mm were prepared for compressive strength test, 30 cylinders of 150 mm diameter and 300 mm height were prepared for split tensile strength test and 30 beams of size 150 mm x 150 mm x 1000 mm were prepared to carry out the flexural strength test. The results are compared to find the ideal proportion of clay as a replacement for cement. It is found that 10% replacement with 5% hydrated lime gives satisfactory results.

scholarly journals Pengaruh Abu Cangkang Sawit Terhadap Kuat Tekan Dan Kuat Lentur Batubata

2018 ◽  
Vol 3 (1) ◽  
pp. 61
Author(s):  
Herman . ◽  
Rolly I
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Physical Properties ◽  
Water Content ◽  
Strength Test ◽  
Basic Material ◽  
Dry Density ◽  
Soil Mixture ◽  
Palm Shell

This research was conducted to increase the value of compreive strength by adding palm shell ash to the base soil of brick. The palm oil shell was got from the result of the disposal of  Incasari Raya Factory Damasraya. The soil as the basic material of the brick was got from the brick’s manufactory Gunung Sariak Padang. The persentage of palm shell ash in the soil mixture was 0%, 5%, 15% and 25% from the soil dry weight. The test consisted of physical properties test and mechanical properties test. The physical properties test consisted of water content test, spesific gravity test, Atterberg limit test, and grain size analysis test.The mechanical properties test consisted of compaction test, compressive strength test and flexural strength test. The water content in manufacture brick was 0,85% γd maximum on wet side optimum of the soi. All the process of the brick is manufactured with manual fabrication. The result of the test showed that the values of spesific gravity (Gs), plastic limit (PL), shrinkage limit (SL),maximum dry density, optimum of water content, and compressive strength of brick increased. Mean while the liquid limit (LL),passing of sieve no. 200 in three days care, plastic index (PI), decreased. For flexural strength, at first increased, along with addition percentage from palm shell ash, this value inclined decreased. The optimum result was got 5%        palm shell ash in the soil mixture.

scholarly journals Evaluation of Interlocking Brick

2021 ◽  
Vol 9 (8) ◽  
pp. 3002-3008
Author(s):  
C. Mounika
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Crumb Rubber ◽  
Strength Test ◽  
Fine Aggregate ◽  
Coir Fiber ◽  
Split Tensile Strength ◽  
Rubber Tire

Abstract: The main aim of this project is to evaluate mechanical properties of interlocking bricks using coir fiber powder as a substitute of cement and rubber tire waste as a substitute of fine aggregate (sand) with varying percentages of 0%, 1%, 2% & 3% and 0%, 5%, 10% & 15% in concrete and to help in solving environmental problem produced from disposing of waste tires and coir husk partially. Additionally fly ash was also added with varying percentages of 5%, 10% and 15% as a substitute to cement in a concrete mix. Several laboratory tests such as compressive strength test, flexural strength test, split tensile strength test, water absorption test and density of concrete etc., were conducted on hardened concrete specimen to achieve the optimum usage of crumb rubber tire waste and coir fiber powder in mix proportion of concrete. It is found that the maximum compressive strength value of coir fiber based crumb rubber interlocking brick was obtained at 1%CF + 5%FA + 5%CR, flexural strength value and split tensile strength value of coir fiber based crumb rubber concrete block was obtained at 1%CF + 5%FA + 5%CR. From the final conclusion or outcome of the project, optimum usage of coir fiber powder is 3% and crumb rubber is 5%. Keywords: coir fiber powder, crumb rubber tire waste, mechanical properties, interlocking bricks & optimum usage.

The Crack Resistance and Impermeability Properties of Mortar with PP Fiber and Capillary Crystalline Material and their Mechanism

2010 ◽  
Vol 168-170 ◽  
pp. 1381-1387
Author(s):  
Wei Huang ◽  
Ping Wang ◽  
Wan Yun Yin ◽  
Li Zhang ◽  
Wei Shu
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Crack Resistance ◽  
Polypropylene Fiber ◽  
Crystalline Material ◽  
Test Results ◽  
Mortar Matrix

According to the principle that fiber resist crack and cement-based capillary crystalline impermeability, the paper chose the mortar added with polypropylene fiber and SJ capillary crystalline material as the research object. Experiments on mechanical properties, crack resistance and impermeability of mortar were conducted with one material being added to the mortar as well as both materials being added to. The test results indicate that the ratio of compressive strength to flexural strength of mortar could be reduced, the time of cracks occurrence in mortar matrix would be delayed, and the minimum cracking coefficient can amount to 5% on the condition that the two materials are both added to the mortar, moreover, the mortar’s first and second impermeability is significant. Furthermore, the paper also discusses the mechanism of mortar’s crack resistance and impermeability which is mixed with polypropylene fiber and capillary crystalline material.

Sign in / Sign up

Export Citation Format

Share Document