scholarly journals Influence of Preparation Method on Properties of Natural Rubber/Sepiolite Composites

2021 ◽  
Vol 2129 (1) ◽  
pp. 012075
Author(s):  
Patiwarada Jitsopin ◽  
Abdulhakim Masa ◽  
Nabil Hayeemasae ◽  
Mohamad Syahmie Mohamad Rasidi
Keyword(s):  
Tensile Strength ◽  
Stress Relaxation ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Preparation Method ◽  
Rubber Composites ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Mixing Method

Abstract Natural rubber (NR) composites filled with various sepiolite loadings were prepared and optimized by two different mixing methods, namely, melt mixing and latex mixing methods. The properties were evaluated through viscosity, stress relaxation, curing behaviors and tensile properties of rubber composites. The viscosity was influenced by sepiolite content and mixing methods. The greater interaction between rubber and sepiolite was obtained from melt mixing method. This reflected to the greater tensile strength found in this method. Considering the content of sepiolite, similar trend was observed for the curing properties and elongation at break. The greatest tensile strength was observed when the sepiloite content was at 1 phr.

Tensile Properties of Wollastonite Filled High Density Polyethylene/Natural Rubber Composites

2015 ◽  
Vol 754-755 ◽  
pp. 215-219
Author(s):  
Ismail Yuhaida ◽  
Husseinsyah Salmah ◽  
Hanafi Ismail ◽  
Zainuddin Firuz
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Tensile Properties ◽  
High Density Polyethylene ◽  
High Density ◽  
Inorganic Filler ◽  
Rotor Speed ◽  
Rubber Composites ◽  
Elongation At Break ◽  
Natural Rubber Composites

Wollastonite is one type of inorganic filler. The effects of wollastonite loading on tensile properties of wollastonite (WS) filled high density polyethylene (HDPE)/Natural Rubber (NR) composites was studied. The HDPE/NR/WS composites were prepared by using Brabender EC Plus at a temperature of 180 °C with rotor speed of 50 rpm for 10 min. It was found that the increasing of wollastonite loading had decreased the tensile strength and elongation at break, whereas the Young’s modulus of the HDPE/NR/WS composites had increased with the increasing of wollastonite loading.

scholarly journals The effects of alkanolamide addition on cure characteristics, swelling behaviour and tensile properties of silica-filled natural rubber (NR) / chloroprene rubber (CR) blends

2018 ◽  
Vol 34 ◽  
pp. 01030 ◽  
Author(s):  
Indra Surya ◽  
Syahrul Fauzi Siregar ◽  
Hanafi Ismail
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Crosslink Density ◽  
Tensile Modulus ◽  
Palm Stearin ◽  
Swelling Behaviour ◽  
Elongation At Break ◽  
Cure Characteristics ◽  
Chloroprene Rubber

Effects of alkanolamide (ALK) addition on cure characteristics, swelling behaviour and tensile properties of silica-filled natural rubber (NR)/chloroprene rubber (CR) blends were investigated. The ALK was synthesized from Refined Bleached Deodorized Palm Stearin (RBDPS) and diethanolamine, and incorporated into the silica-filled NR/CR blends as a non-toxic rubber additive. The ALK loadings were 0.0, 1.0, 3.0, 5.0 and 7.0 phr. It was found that the ALK exhibited shorter scorch and cure times and higher elongation at break of the silica-filled NR/CR blends. The ALK also exhibited higher torque differences, tensile modulus and tensile strength at a 1.0 phr of ALK loading and then decreased with further increases in the ALK loading. The swelling measurement proved that the 1.0 phr loading of ALK caused the highest degree in crosslink density of the silica-filled NR/CR blends.

scholarly journals Thermal, Morphological and Physic-Mechanical Properties of Natural Rubber - CaCO3 Composites Using Jatropha Oil as Softener.

2018 ◽  
Vol 156 ◽  
pp. 05016 ◽  
Author(s):  
Nasruddin ◽  
Tri Susanto
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Abrasion Resistance ◽  
Compositional Analysis ◽  
Critical Issue ◽  
Green Technology ◽  
Jatropha Oil ◽  
Rubber Composites ◽  
Elongation At Break ◽  
Natural Rubber Composites

The urgency of green technology in rubber compounding has become a critical issue recently. In this research, the effect of using renewable resources in rubber compounding has been studied. Commercial Calcium Carbonate, Silica and Jatropha Oil were used in natural rubber composite. The research was designed by varying the types of commercial filler namely CaCO3 (47-51) phr, silica (47-51) phr and Jatropha Oil (4-6) phr in natural rubber composites (SIR-20). The formulas were intentionally designed for rubber tips vulcanizates. The samples were characterized by the determination of physic-mechanical, thermal (TGA) and morphological (SEM) properties. From the measured results, there is no significant effect on the tensile strength, specific gravity, and hardness on the loading of commercial CaCO3 and Silica in natural rubber composites using Jatropha Oil. However, a slight difference in elongation at break and abrasion resistance could be detected. Compared to the commercial rubber tips, the rubber tips produced in this research have higher tensile strength, elongation at break and abrasion resistance. Due to the usage of commercial CaCO3 and Silica, the SEM micrographs show rough surface because of the agglomeration. The thermogram shows clearly the compositional analysis of the rubber tips vulcanizates consist of Jatropha Oil and natural rubber, CaCO3, ash and other filler residues such as Silica.

Effect of Short Banana Fiber on Hardness and Tensile Properties of Natural Rubber Composites

2021 ◽  
Vol 904 ◽  
pp. 232-236
Author(s):  
Thapanee Wongpreedee ◽  
Chana Prapruddivongs ◽  
Nanthaya Kengkhetkit
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Fiber Content ◽  
Rubber Composites ◽  
Banana Fiber ◽  
Roll Mill ◽  
Natural Rubber Composites ◽  
Reinforcing Filler

Banana fiber (BF) was utilized as a reinforcing filler for natural rubber (NR). BF/NR composites containing banana fiber contents of 5, 10, and 15 parts per hundred parts of rubber (phr) were mixed on a two-roll mill machine. The hardness, tensile properties of BF/NR composites were studied. It was found that the hardness and moduli of BF/NR composites are higher than that of NR. Despite tensile strength and strain at break of BF/NR composite lower than NR. Moreover, hardness and moduli of BF/NR composites increased, while tensile strength and strain at break decreased with the increase in banana fiber content. Thus, banana fiber exhibited improvement in the stiffness significantly of NR composites

Effect of Polyethylene Grafted Maleic Anhydride (PEgMAH) on Tensile Properties and Swelling Behavior of Ethylene Vinyl Acetate (EVA)/ Natural Rubber (NR)/ Feldspar Composites

2014 ◽  
Vol 554 ◽  
pp. 141-144 ◽  
Author(s):  
S.H. Ho ◽  
A.Ghani Supri ◽  
Pei Leng Teh
Keyword(s):  
Tensile Strength ◽  
Maleic Anhydride ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Vinyl Acetate ◽  
Ethylene Vinyl Acetate ◽  
Swelling Behavior ◽  
Rotor Speed ◽  
Elongation At Break ◽  
Lower Elongation

The effects of polyethylene grafted maleic anhydride (PEgMAH) as a compatibilizer on the tensile properties and swelling behavior of ethylene vinyl acetate /Natural Rubber/ Feldspar (EVA/NR/FP) composites were studied. The EVA/NR/FP composites with and without PEgMAH were prepared using Brabender Plasticoder at 160oC with 50rpm rotor speed. The results indicated that EVA/NR/FP/PEgMAH had higher value of tensile strength and M100 but lower elongation at break and percentage mass swell.

Tensile Properties and Morphology of Recycled Latex Glove Filled Epoxidized Natural Rubber (ENR50) Compounds

2014 ◽  
Vol 660 ◽  
pp. 306-311
Author(s):  
A.A. Afiratul ◽  
N.Z. Noimam ◽  
C.M. Ruzaidi ◽  
Sung Ting Sam ◽  
M.F. Omar ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Tensile Properties ◽  
High Surface ◽  
Weight Ratio ◽  
Epoxidized Natural Rubber ◽  
Elongation At Break ◽  
Latex Glove ◽  
Roll Mill ◽  
Fine Size

The effects on the properties of recycled latex glove (RL-G) filled Epoxidized Natural Rubber (ENR 50) were studied. Both compounds were prepared by two roll mill at five different compositions of RL-G (5, 15, 25, 35 and 50 phr). The size range of RL-G particles i.e., S1 (300μm-700μm) and S2 (3cm-5cm) were used. The properties such as tensile properties (tensile strength, elongation at break, and stress at 100% elongation) and morphology studies were determined. The results indicated that the both size, S1 and S2 of recycled latex glove filled ENR 50 blends exhibited an increased in tensile strength and elongation at break for increasing weight ratio of RL-G. Scanning electron microscopy (SEM) of the fracture surfaces shows that the fine size, S1 RL-G/ENR50 exhibited high surface roughness and matrix tearing lines than the coarse size, S2 thus improving the compatibility of RL-G/ENR50 compounds. The results overall indicated that the fine size, S1of RL-G filled ENR50 contributed to the better properties such as tensile strength and surface morphology compared to the coarse size, S2 mainly at 15 phr of RL-G content.

Cogon Grass Fiber-Epoxidized Natural Rubber Composites

2013 ◽  
Vol 747 ◽  
pp. 375-378 ◽  
Author(s):  
Chaiwat Ruksakulpiwat ◽  
Wasaphon Wanasut ◽  
Apikiat Singkum ◽  
Ruksakulpiwat Yupaporn
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Acid Treatment ◽  
Treatment Time ◽  
Treatment Method ◽  
Epoxidized Natural Rubber ◽  
Rubber Composites ◽  
Elongation At Break ◽  
Natural Rubber Composites

This research shows a great potential of cogon grass fiber to be used as a reinforcement in epoxidized natural rubber composites. The thermal and mechanical properties of cogon grass fiber-epoxidized natural rubber composites were studied. The chemical treatment of cogon grass fiber to be used as a reinforcing filler was revealed. Effects of fiber treatment method and treatment time of cogon grass fiber on thermal properties of the fibers and their composites were elucidated. The addition of cogon grass fiber into epoxidized natural rubber (ENR) improved the mechanical properties of the composites.The result indicated that alkaline treatment followed by acid treatment of cogon grass fiber led to an increase in thermal decomposition temperature and mechanical properties of the composites more than that without acid treatment. With increasing the amount of fiber, tensile strength of ENR composites were significantly increased while elongation at break was insignificantly changed. ENR with the addition of 4-Amino-6-hydroxy-2-mercaptopyrimidine monohydrate as coupling agent (ENRC) was shown to have higher tensile strength, modulus at 200% elongation and elongation at break than ENR. Improved mechanical properties were also obtained in ENRC composites compared to those of ENR composites.

Electrical Properties of Graphene Filled Natural Rubber Composites

2013 ◽  
Vol 812 ◽  
pp. 263-266 ◽  
Author(s):  
Yaragalla Srinivasarao ◽  
Yahaya Subban Ri Hanum ◽  
Chin Han Chan ◽  
Kalarikkal Nandakumar ◽  
Thomas Sabu
Keyword(s):  
Dielectric Constant ◽  
Graphene Oxide ◽  
Natural Rubber ◽  
Conductivity Data ◽  
Rubber Composites ◽  
Melt Mixing ◽  
Electrical Percolation ◽  
Natural Rubber Composites ◽  
Reduced Graphene ◽  
Mixing Method

Thermally reduced graphene oxide (graphene) filled natural rubber (NR) composites were fabricated by melt mixing method. Dielectric constant, dielectric loss and a.c conductivity data of the NR composites are reported. Highest conductivity of 3 x 10-4 S/m was obtained for the composite with 3 wt. % graphene with initial electrical percolation at a loading of 0.5 wt. %. High conductivity in the composite with 3 wt. % graphene is accounted by its homogeneity as observed in SEM micrographs.

Physical Properties of Rice Husk Fiber/Natural Rubber Composites

2011 ◽  
Vol 410 ◽  
pp. 90-93 ◽  
Author(s):  
Ladawan Srisuwan ◽  
Kasama Jarukumjorn ◽  
Nitinat Suppakarn
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Rice Husk ◽  
Crosslink Density ◽  
Morphological Properties ◽  
Rubber Composites ◽  
Elongation At Break ◽  
Natural Rubber Composites ◽  
Reinforcing Filler

In this study, rice husk fiber (RHF) was used as a reinforcing filler for natural rubber (NR). NR composites were prepared at various RHF contents, i.e., 10, 20, 30, 40 and 50 phr. Sulfur conventional vulcanization was used. Effect of RHF content on cure characteristics, mechanical properties and morphological properties of NR composites were investigated. The results showed that scorch and cure times of RHF/NR composites were not affected by increasing RHF content. Crosslink density, tensile strength, elongation at break and tear strength of NR composites slightly decreased with increasing RHF content whereas M100 and M300 of the composites slightly increased with increasing RHF content.

Tensile Properties of Linear Low Density Polyethylene (LLDPE)/ Recycled Acrylonitrile Butadiene Rubber (NBRr)/ Rice Husk Powder (RHP) Composites

2015 ◽  
Vol 754-755 ◽  
pp. 210-214 ◽  
Author(s):  
Ragunathan Santiagoo ◽  
Sam Sung Ting ◽  
Hanafi Ismail ◽  
Mastura Jaafar
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Rice Husk ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Butadiene Rubber ◽  
Linear Low Density Polyethylene ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Acrylonitrile Butadiene Rubber

The compatibilizer effect of ENR-50 on the tensile properties and morphology of linear low density polyethylene (LLDPE)/ recycled acrylonitrile butadiene rubber (NBRr)/ rice husk powder (RHP) composites has been studied. The RHP size utilize in this work is 150 – 300 μm. LLDPE/NBRr/RHP composites were prepared by melt mixing technique at 180 °C for 9 minutes at 50 rpm rotor speed using heated two roll mill. The series of composites investigated were 100/0/5, 80/20/5, 70/30/5, 60/40/5, 50/50/5, and 40/60/5. The composites were analysed by using tensile test and morphology examination. The result showed that the tensile strength of composite was decreased with the increasing of recycled acrylonitrile butadiene rubber (NBRr) content while elongation at break (Eb) were increased. However, the tensile strength and elongation at break result for composites with ENR-50 as compatibilizer showed higher values. The morphological finding supports the tensile properties which indicate better interaction between the RHP filler and LLDPE/NBRr matrix in the presence of ENR-50 compatibilizer.

Sign in / Sign up

Export Citation Format

Share Document