scholarly journals Numerical simulation of box culverts subjected to different physical actions and design regulations

2022 ◽  
Vol 2153 (1) ◽  
pp. 012002
Author(s):  
M V Afanador Arias ◽  
J S Pacheco-Posada ◽  
N Afanador García
Keyword(s):  
Structural Design ◽  
American Association ◽  
Research Work ◽  
Visual Basic ◽  
Vehicular Traffic ◽  
Analysis And Design ◽  
State Highway ◽  
Wide Range ◽  
Significant Difference ◽  
Box Culverts

Abstract This research work was intended to provide a broad and suffcient solution to areas of diffcult vehicular traffic, where during the rainy season some watersheds present a non negligible water flow. The research carried out the structural design of different geometries of box culverts, to provide a solution to vehicular continuity in areas affected by water ows that interrupt pedestrian and vehicle traffic, endangering human lives. The structural designs followed the standards established by the American Association of State Highway and Transportation Offcials and the Colombian bridge code. The designs were carried out using commercial software SAP2000 for analysis and design through Visual Basic programming, allowing a wide range of geometries and boundary conditions to be established. The structural designs indicated a significant difference in quantities of work in the construction of the box culverts for different geometries, indicating higher volumes of concrete for the designs made using the American Association of State Highway and Transportation Offcials code compared to Colombian bridge code. The Colombian bridge code has higher steel requirements for fills less than 3.00 m, while for greater heights the American Association of State Highway and Transportation Offcials code has the highest steel requirements.

Crash Testing and Evaluation of Culvert-Mounted Midwest Guardrail System

2020 ◽  
Vol 2674 (7) ◽  
pp. 161-171
Author(s):  
Mojdeh Asadollahi Pajouh ◽  
Robert W. Bielenberg ◽  
Jennifer D. Schmidt-Rasmussen ◽  
Ronald K. Faller
Keyword(s):  
American Association ◽  
Water Drainage ◽  
Test Installation ◽  
State Highway ◽  
Crash Testing ◽  
Test Number ◽  
Box Culverts ◽  
Level 3 ◽  
Crash Tests ◽  
Test Level

Concrete box culverts are usually installed under roadways to allow water drainage without affecting the motoring public. Culvert openings can represent a hazard on the roadside when they do not extend outside of the clear zone, and often require safety treatments in the form of roadside barriers. In this study, a modified design of Midwest Guardrail System (MGS) was evaluated for installation on a low-fill culvert with the strong-post attachment using through-bolts and epoxy anchorage through full-scale crash testing. The test installation consisted of MGS with a 31 in. top rail height, supported by W6 × 9 posts, spaced at 37½ in., attached to a low-fill culvert’s top slab with a 12 in. offset from the back of the post to the culvert headwall. Two crash tests were conducted according to the American Association of State Highway and Transportation Officials’ (AASHTO) Manual for Assessing Safety Hardware (MASH) 2016 Test Level 3 impact safety criteria. In test number CMGS-1, a 2,428-lb car impacted the MGS attached to the culvert at a speed of 61.3 mph and at an angle of 25.1°. In test number CMGS-2, a 5,013-lb pickup truck impacted the MGS attached to the culvert at a speed of 62.8 mph and an angle of 25.7°. In both tests, the vehicle was safely redirected and captured. Both tests were deemed acceptable according to TL-3 safety criteria in MASH. Recommendations were made for the safe installation of MGS atop low-fill culverts as well as transitions from the standard MGS to the culvert-mounted MGS.

Nonlinear Dynamic Analysis for the New Whole-Spacecraft Passive Vibration Isolator

2013 ◽  
Vol 300-301 ◽  
pp. 1231-1234 ◽  
Author(s):  
Li Jun Tan ◽  
Bo Fang ◽  
Jie Jie Zhang ◽  
Wen Hu Huang
Keyword(s):  
Vibration Isolation ◽  
Research Work ◽  
Influence Factors ◽  
Nonlinear Dynamic Analysis ◽  
Vibration Isolator ◽  
Isolation System ◽  
Practical Applications ◽  
Analysis And Design ◽  
Nonlinear Motion ◽  
Wide Range

The nonlinear vibration analysis related to viscoelastic damper is investigated for the new whole-spacecraft passive vibration isolator. The stepped sinusoidal sweep test is performed and the results reveal the nonlinearity of the system. The nonlinear motion equation is developed. The frequency response equation is derived by the method of harmonic balance. The experiment of various excitation levels are carried out contrasting with numerical simulations. The nonlinear influence factors to the vibration isolation system are argued and the identification results explain the effect parameters on the performance of the vibration isolator. The research work is of significant implications for the analysis and design of passive vibration isolator for a wide range of practical applications.

Justification of the need to improve the legal, regulatory and methodological framework for the spread of parasitic infections in the provision of medical care

2020 ◽  
Vol 99 (5) ◽  
pp. 493-497
Author(s):  
M. M. Aslanova ◽  
T. V. Gololobova ◽  
K. Yu. Kuznetsova ◽  
Tamari R. Maniya ◽  
D. V. Rakitina ◽  
...  
Keyword(s):  
Medical Care ◽  
Research Work ◽  
Hospital Environment ◽  
Parasitic Infections ◽  
Infusion Therapy ◽  
Methodological Framework ◽  
Production Environment ◽  
Medical Institutions ◽  
Medical Network ◽  
Wide Range

Introduction. The purpose of our work was to justify the need to improve the legislative, regulatory and methodological framework and preventative measures in relation to the spread of parasitic infections in the provision of medical care. There is a wide range of pathogens of parasitic infestations that are transmitted to humans through various medical manipulations and interventions carried out in various medical institutions. Contaminated care items and furnishings, medical instruments and equipment, solutions for infusion therapy, medical personnel’s clothing and hands, reusable medical products, drinking water, bedding, suture and dressing materials can serve as a major factor in the spread of parasitic infections in the provision of medical care. Purpose of research is the study of the structure and SMP of parasitic origin, circulating on the objects of the production environment in multi-profile medical and preventive institutions of stationary type in order to prevent the occurrence of their spread within medical institutions. Material and methods. The material for the study was flushes taken from the production environment in 3 multi-profile treatment and prevention institutions of inpatient type: a multi-specialty hospital, a maternity hospital and a hospital specializing in the treatment of patients with intestinal diseases for the eggs of worms and cysts of pathogenic protozoa. Results. During the 2-year monitoring of medical preventive institutions, a landscape of parasitic contamination was found to be obtained from the flushes taken from the production environment objects in the premises surveyed as part of the research work. Discussions. In the course of research, the risk of developing ISMP of parasitic origin was found to be determined by the degree of epidemiological safety of the hospital environment, the number and invasiveness of treatment and diagnostic manipulations and various medical technologies. Conclusion. It is necessary to conduct an expert assessment of regulatory and methodological documents in the field of epidemiological surveillance and sanitary and hygienic measures for the prevention of medical aid related infections of parasitic origin, to optimize the regulatory and methodological base, to develop a number of preventive measures aimed at stopping the spread of parasitic infections in the medical network.

The Effect of Using Students Peer Teaching on Iraqi EFL Students' Achievement in the Course of Library and Research Work

2019 ◽  
Vol 1 (33) ◽  
pp. 693-714
Author(s):  
. Muntaha Sabbar Jebur
Keyword(s):  
Basic Education ◽  
Teaching Method ◽  
Research Work ◽  
Peer Teaching ◽  
Control Group ◽  
College Of Basic Education ◽  
Significant Difference ◽  
Post Test ◽  
Efl Students ◽  
Experimental Group

          Peer teaching is a strategy that allows the students to teach the new content to each other, and they must be accurately guided by instructors.     The researcher proposes that the use of students peer teaching  may promote students' achievement  and ensure the engagement of all the students in the learning process. Therefore, the researcher employs it as a teaching method aiming at investigating its  effect on Iraqi EFL students' achievement in the course of Library and Research Work .      The study hypothesizes that there is no significant difference between the students' achievement who are taught library and research work by students peer teaching  and that of the students taught by the traditional way. The experimental design of the study is Parallel Groups, Random Assignment, posttest. Each group consists of 35 students, chosen randomly from the Third Year Students at the Department of English in the College of Basic Education. Both groups were matched in terms of their age and parents' education. The experiment was fulfilled in the first course for 15 weeks during the academic year 2016-2017.       The same materials were presented to both groups. This included   units from Writing Research Paper by Lester D. . Post-test was constructed and exposed  The t-test for  independent samples was used to analyze the results and it is found out that there is a statistical difference between the two groups in their achievement because the calculated t- value 2.635 is bigger than the tabulated t- value which is 2.000, and also shown the superiority of the experimental group. The results indicate that the experimental group, who was taught Library and Research Work by peer teaching   was better than the control group, who was taught according to the traditional way. So, the null hypothesis is rejected. Finally, some recommendations and suggestions are presented in the light of the study findings. to a jury of experts to verify its validity and it was administered to both groups.

Development and Evaluation of Sustained Release Lipid Nanocarriers for Curcumin

2020 ◽  
Vol 5 (3) ◽  
pp. 224-235
Author(s):  
Harshal A. Pawar ◽  
Bhagyashree D. Bhangale
Keyword(s):  
Drug Delivery ◽  
Sustained Release ◽  
Drug Delivery Systems ◽  
Biological Activities ◽  
Curcuma Longa ◽  
Research Work ◽  
Elimination Rate ◽  
Delivery Systems ◽  
Physicochemical Stability ◽  
Wide Range

Background: Lipid based excipients have increased acceptance nowadays in the development of novel drug delivery systems in order to improve their pharmacokinetic profiles. Drugs encapsulated in lipids have enhanced stability due to the protection they experience in the lipid core of these nano-formulations. Phytosomes are newly discovered drug delivery systems and novel botanical formulation to produce lipophilic molecular complex which imparts stability, increases absorption and bioavailability of phytoconstituent. Curcumin, obtained from turmeric (Curcuma longa), has a wide range of biological activities. The poor solubility and wettability of curcumin are responsible for poor dissolution and this, in turn, results in poor bioavailability. To overcome these limitations, the curcumin-loaded nano phytosomes were developed to improve its physicochemical stability and bioavailability. Objective: The objective of the present research work was to develop nano-phytosomes of curcumin to improve its physicochemical stability and bioavailability. Methods: Curcumin-loaded nano phytosomes were prepared by using phospholipid Phospholipon 90 H using a modified solvent evaporation method. The developed curcumin nano phytosomes were evaluated by particle size analyzer and differential scanning calorimetry (DSC). Results: Results indicated that phytosomes prepared using curcumin and lipid in the ratio of 1:2 show good entrapment efficiency. The obtained curcumin phytosomes were spherical in shape with a size less than 100 nm. The prepared nano phytosomal formulation of curcumin showed promising potential as an antioxidant. Conclusion: The phytosomal complex showed sustained release of curcumin from vesicles. The sustained release of curcumin from phytosome may improve its absorption and lowers the elimination rate with an increase in bioavailability.

The Impact of using 3D Interactive Animation Tool in Teaching Computer Programming at the Senior High School Level

2018 ◽  
Vol 3 (2) ◽  
pp. 18-28
Author(s):  
Najim Ussiph ◽  
Hamidu Kwame Seidu
Keyword(s):  
High School ◽  
Research Work ◽  
Instructional Method ◽  
Senior High School ◽  
School Level ◽  
Eastern Region ◽  
3D Animation ◽  
High School Level ◽  
Significant Difference ◽  
The Impact

A quasi experiment with interview was adopted to study the aptness of using 3D animations as an instructional method to introduce programming concepts to students at the Senior High School level. This research work was conducted with 100 students of Akroso Senior High School in the Birim central municipality of the eastern region of Ghana who were generally programming novice. Programming concepts considered included programming environments, loops, functions sequential and conditional execution of programs. A paired t-test carried out on the results of the performance test presents a p-value of 0.008 indicative of a numerically significant difference between the mean marks of participants during the experiments that used 3D animation method as against the experiments that used the text base method. Results from the interview showed that the instructional method used had impact on the performance of the learners. The use of 3D animation method presented programming concepts in a form that the learners can understand, motivates them to pursue programming related courses at a higher level and also impacts positively on their performance.

ESRC Review

2020 ◽  
pp. 657-698
Author(s):  
Simeon J. Yates ◽  
Jordana Blejmar
Keyword(s):  
Social Research ◽  
Social Science Research ◽  
Research Work ◽  
Science Research ◽  
Wide Range ◽  
The Us ◽  
Levels Of Automation ◽  
The Uk ◽  
Technological World ◽  
Ways Of Being

Two workshops were part of the final steps in the Economic and Social Research Council (ESRC) commissioned Ways of Being in a Digital Age project that is the basis for this Handbook. The ESRC project team coordinated one with the UK Defence Science and Technology Laboratory (ESRC-DSTL) Workshop, “The automation of future roles”; and one with the US National Science Foundation (ESRC-NSF) Workshop, “Changing work, changing lives in the new technological world.” Both workshops sought to explore the key future social science research questions arising for ever greater levels of automation, use of artificial intelligence, and the augmentation of human activity. Participants represented a wide range of disciplinary, professional, government, and nonprofit expertise. This chapter summarizes the separate and then integrated results. First, it summarizes the central social and economic context, the method and project context, and some basic definitional issues. It then identifies 11 priority areas needing further research work that emerged from the intense interactions, discussions, debates, clustering analyses, and integration activities during and after the two workshops. Throughout, it summarizes how subcategories of issues within each cluster relate to central issues (e.g., from users to global to methods) and levels of impacts (from wider social to community and organizational to individual experiences and understandings). Subsections briefly describe each of these 11 areas and their cross-cutting issues and levels. Finally, it provides a detailed Appendix of all the areas, subareas, and their specific questions.

scholarly journals Biochemical and molecular characterization of Alternaria alternata isolates highly resistant to procymidone from broccoli and cabbage

2021 ◽  
Vol 3 (1) ◽  
Author(s):  
Bingran Wang ◽  
Tiancheng Lou ◽  
Lingling Wei ◽  
Wenchan Chen ◽  
Longbing Huang ◽  
...  
Keyword(s):  
Alternaria Alternata ◽  
Single Point ◽  
Sodium Dodecyl ◽  
Cross Resistance ◽  
Molecular Characteristics ◽  
Single Point Mutation ◽  
Wide Range ◽  
Significant Difference ◽  
Leaf Blights ◽  
High Level

AbstractAlternaria alternata, a causal agent of leaf blights and spots on a wide range of hosts, has a high risk of developing resistance to fungicides. Procymidone, a dicarboximide fungicide (DCF), has been widely used in controlling Alternaria leaf blights in China for decades. However, the resistance of A. alternata against DCFs has rarely been reported from crucifer plants. A total of 198 A. alternata isolates were collected from commercial fields of broccoli and cabbage during 2018–2019, and their sensitivities to procymidone were determined. Biochemical and molecular characteristics were subsequently compared between the high-level procymidone-resistant (ProHR) and procymidone-sensitive (ProS) isolates, and also between ProHR isolates from broccoli and cabbage. Compared with ProS isolates, the mycelial growth rate, sporulation capacity and virulence of most ProHR isolates were reduced; ProHR isolates displayed an increased sensitivity to osmotic stresses and a reduced sensitivity to sodium dodecyl sulfate (SDS); all ProHR isolates showed a reduced sensitivity to hydrogen peroxide (H2O2) except for the isolate B102. Correlation analysis revealed a positive cross-resistance between procymidone and iprodione, or fludioxonil. When treated with 10 μg/mL of procymidone, both mycelial intracellular glycerol accumulations (MIGAs) and relative expression of AaHK1 in ProS isolates were higher than those in ProHR isolates. Sequence alignment of AaHK1 from ten ProHR isolates demonstrated that five of them possessed a single-point mutation (P94A, V612L, E708K or Q924STOP), and four isolates had an insertion or a deletion in their coding regions. No significant difference in biochemical characteristics was observed among ProHR isolates from two different hosts, though mutations in AaHK1 of the cabbage-originated ProHR isolates were distinct from those of the broccoli-originated ProHR isolates.

scholarly journals Antifungal Activity of Propyl Disulfide from Neem (Azadirachta indica) in Vapor and Agar Diffusion Assays against Anthracnose Pathogens (Colletotrichum gloeosporioides and Colletotrichum acutatum) in Mango Fruit

2021 ◽  
Vol 9 (4) ◽  
pp. 839
Author(s):  
Muhammad Rafiullah Khan ◽  
Vanee Chonhenchob ◽  
Chongxing Huang ◽  
Panitee Suwanamornlert
Keyword(s):  
Antifungal Activity ◽  
Mycelial Growth ◽  
Colletotrichum Gloeosporioides ◽  
Colletotrichum Acutatum ◽  
Model Parameters ◽  
Pathogenicity Test ◽  
Agar Diffusion ◽  
Wide Range ◽  
Significant Difference ◽  
Diffusion Assay

Microorganisms causing anthracnose diseases have a medium to a high level of resistance to the existing fungicides. This study aimed to investigate neem plant extract (propyl disulfide, PD) as an alternative to the current fungicides against mango’s anthracnose. Microorganisms were isolated from decayed mango and identified as Colletotrichum gloeosporioides and Colletotrichum acutatum. Next, a pathogenicity test was conducted and after fulfilling Koch’s postulates, fungi were reisolated from these symptomatic fruits and we thus obtained pure cultures. Then, different concentrations of PD were used against these fungi in vapor and agar diffusion assays. Ethanol and distilled water were served as control treatments. PD significantly (p ≤ 0.05) inhibited more of the mycelial growth of these fungi than both controls. The antifungal activity of PD increased with increasing concentrations. The vapor diffusion assay was more effective in inhibiting the mycelial growth of these fungi than the agar diffusion assay. A good fit (R2, 0.950) of the experimental data in the Gompertz growth model and a significant difference in the model parameters, i.e., lag phase (λ), stationary phase (A) and mycelial growth rate, further showed the antifungal efficacy of PD. Therefore, PD could be the best antimicrobial compound against a wide range of microorganisms.

scholarly journals A Threat of Farmers’ Suicide and the Opportunity in Organic Farming for Sustainable Agricultural Development in India

2019 ◽  
Vol 11 (8) ◽  
pp. 2400 ◽  
Author(s):  
Karthikeyan Mariappan ◽  
Deyi Zhou
Keyword(s):  
Organic Farming ◽  
Tamil Nadu ◽  
Agricultural Development ◽  
Small Scale ◽  
Conventional Farming ◽  
Wide Range ◽  
Significant Difference ◽  
Small Scale Farmers ◽  
The Cost ◽  
Input Cost

Agriculture is the main sources of income for humans. Likewise, agriculture is the backbone of the Indian economy. In India, Tamil Nadu regional state has a wide range of possibilities to produce all varieties of organic products due to its diverse agro-climatic condition. This research aimed to identify the economics and efficiency of organic farming, and the possibilities to reduce farmers’ suicides in the Tamil Nadu region through the organic agriculture concept. The emphasis was on farmers, producers, researchers, and marketers entering the sustainable economy through organic farming by reducing input cost and high profit in cultivation. A survey was conducted to gather data. One way analysis of variance (ANOVA) has been used to test the hypothesis regards the cost and profit of rice production. The results showed that there was a significant difference in profitability between organic and conventional farming methods. It is very transparent that organic farming is the leading concept of sustainable agricultural development with better organic manures that can improve soil fertility, better yield, less input cost and better return than conventional farming. The study suggests that by reducing the cost of cultivation and get a marginal return through organic farming method to poor and small scale farmers will reduce socio-economic problems such as farmers’ suicides in the future of Indian agriculture.

Sign in / Sign up

Export Citation Format

Share Document