scholarly journals Mutual assessment during ritualized fighting in mantis shrimp (Stomatopoda)

2018 ◽  
Vol 285 (1871) ◽  
pp. 20172542 ◽  
Author(s):  
P. A. Green ◽  
S. N. Patek
Keyword(s):  
Body Size ◽  
Network Analysis ◽  
Experimental Tests ◽  
Theoretical Models ◽  
Resource Holding Potential ◽  
Self Assessment ◽  
Mantis Shrimp ◽  
Behavioural Analysis ◽  
Survival And Reproduction ◽  
Strong Inference

Safe and effective conflict resolution is critical for survival and reproduction. Theoretical models describe how animals resolve conflict by assessing their own and/or their opponent's ability (resource holding potential, RHP), yet experimental tests of these models are often inconclusive. Recent reviews have suggested this uncertainty could be alleviated by using multiple approaches to test assessment models. The mantis shrimp Neogonodactylus bredini presents visual displays and ritualistically exchanges high-force strikes during territorial contests. We tested how N. bredini contest dynamics were explained by any of three assessment models—pure self-assessment, cumulative assessment and mutual assessment—using correlations and a novel, network analysis-based sequential behavioural analysis. We staged dyadic contests over burrow access between competitors matched either randomly or based on body size. In both randomly and size-matched contests, the best metric of RHP was body mass. Burrow residency interacted with mass to predict outcome. Correlations between contest costs and RHP rejected pure self-assessment, but could not fully differentiate between cumulative and mutual assessment. The sequential behavioural analysis ruled out cumulative assessment and supported mutual assessment. Our results demonstrate how multiple analyses provide strong inference to tests of assessment models and illuminate how individual behaviours constitute an assessment strategy.

The analysis on the influence of mixed sliding-rolling motion mode to precision degradation of ball screw

2021 ◽  
pp. 095440622098201
Author(s):  
Qiang Cheng ◽  
Baobao Qi ◽  
Hongyan Chu ◽  
Ziling Zhang ◽  
Zhifeng Liu ◽  
...  
Keyword(s):  
Structural Parameters ◽  
Experimental Tests ◽  
Theoretical Models ◽  
Operating Conditions ◽  
Ball Screw ◽  
Rolling Motion ◽  
Degradation Model ◽  
Sliding Motion ◽  
Factors Analysis ◽  
Motion Mode

The combination of sliding/rolling motion can influence the degree of precision degradation of ball screw. Precision degradation modeling and factors analysis can reveal the evolution law of ball screw precision. This paper presents a precision degradation model for factors analysis influencing precision due to mixed sliding-rolling motion. The precision loss model was verified through the comparison of theoretical models and experimental tests. The precision degradation due to rolling motion between the ball and raceway accounted for 29.09% of the screw precision loss due to sliding motion. Additionally, the total precision degradation due to rolling motion accounted for 21.03% of the total sliding precision loss of the screw and nut, and 17.38% of the overall ball screw precision loss under mixed sliding-rolling motion. In addition, the effects of operating conditions and structural parameters on precision loss were analyzed. The sensitivity coefficients of factors influencing were used to quantitatively describe impact degree on precision degradation.

Theoretical and empirical scaling patterns and topological homology in bone trabeculae.

1998 ◽  
Vol 201 (4) ◽  
pp. 573-590
Author(s):  
S M Swartz ◽  
A Parker ◽  
C Huo
Keyword(s):  
Body Size ◽  
Surface Area ◽  
Cancellous Bone ◽  
Structural Design ◽  
Theoretical Models ◽  
Small Animals ◽  
Bone Trabeculae ◽  
Large Animals ◽  
Vertebrate Skeleton ◽  
Area And Volume

Trabecular or cancellous bone is a major element in the structural design of the vertebrate skeleton, but has received little attention from the perspective of the biology of scale. In this study, we investigated scaling patterns in the discrete bony elements of cancellous bone. First, we constructed two theoretical models, representative of the two extremes of realistic patterns of trabecular size changes associated with body size changes. In one, constant trabecular size (CTS), increases in cancellous bone volume with size arise through the addition of new elements of constant size. In the other model, constant trabecular geometry (CTG), the size of trabeculae increases isometrically. These models produce fundamentally different patterns of surface area and volume scaling. We then compared the models with empirical observations of scaling of trabecular dimensions in mammals ranging in mass from 4 to 40x10(6)g. Trabecular size showed little dependence on body size, approaching one of our theoretical models (CTS). This result suggests that some elements of trabecular architecture may be driven by the requirements of maintaining adequate surface area for calcium homeostasis. Additionally, we found two key consequences of this strongly negative allometry. First, the connectivity among trabecular elements is qualitatively different for small versus large animals; trabeculae connect primarily to cortical bone in very small animals and primarily to other trabeculae in larger animals. Second, small animals have very few trabeculae and, as a consequence, we were able to identify particular elements with a consistent position across individuals and, for some elements, across species. Finally, in order to infer the possible influence of gross differences in mechanical loading on trabecular size, we sampled trabecular dimensions extensively within Chiroptera and compared their trabecular dimensions with those of non-volant mammals. We found no systematic differences in trabecular size or scaling patterns related to locomotor mode.

scholarly journals Phylogeny versus body size as determinants of food web structure

2012 ◽  
Vol 279 (1741) ◽  
pp. 3291-3297 ◽  
Author(s):  
Russell E. Naisbit ◽  
Rudolf P. Rohr ◽  
Axel G. Rossberg ◽  
Patrik Kehrli ◽  
Louis-Félix Bersier
Keyword(s):  
Body Size ◽  
Food Web ◽  
Food Webs ◽  
Phylogenetic Signal ◽  
Theoretical Models ◽  
Conservation Priorities ◽  
Food Web Structure ◽  
Web Architecture ◽  
Species Overlap ◽  
Using Data

Food webs are the complex networks of trophic interactions that stoke the metabolic fires of life. To understand what structures these interactions in natural communities, ecologists have developed simple models to capture their main architectural features. However, apparently realistic food webs can be generated by models invoking either predator–prey body-size hierarchies or evolutionary constraints as structuring mechanisms. As a result, this approach has not conclusively revealed which factors are the most important. Here we cut to the heart of this debate by directly comparing the influence of phylogeny and body size on food web architecture. Using data from 13 food webs compiled by direct observation, we confirm the importance of both factors. Nevertheless, phylogeny dominates in most networks. Moreover, path analysis reveals that the size-independent direct effect of phylogeny on trophic structure typically outweighs the indirect effect that could be captured by considering body size alone. Furthermore, the phylogenetic signal is asymmetric: closely related species overlap in their set of consumers far more than in their set of resources. This is at odds with several food web models, which take only the view-point of consumers when assigning interactions. The echo of evolutionary history clearly resonates through current food webs, with implications for our theoretical models and conservation priorities.

A Theoretical and Experimental Analysis of the Bending Behavior of Unbonded Flexible Pipes

2014 ◽  
Author(s):  
Tatiana Vargas-Londoño ◽  
José Renato M. de Sousa ◽  
Carlos Magluta ◽  
Ney Roitman
Keyword(s):  
Internal Pressure ◽  
Cross Section ◽  
Structural Response ◽  
Experimental Tests ◽  
Theoretical Models ◽  
External Pressure ◽  
Local Behavior ◽  
Flexible Pipes ◽  
Floating System ◽  
Bending Loads

Due to its compound cross-section, the prediction of the structural response of flexible pipes to loads such as their self-weight, internal and external pressure, movements imposed by the floating system and environmental loads such as currents, waves and wind is quite complex. All these loads generate stresses and strains in the cross section of the pipe that have to be properly evaluated in order to ensure integrity of the line. Research has been done on the local behavior of flexible pipes under combined axisymmetric loads as well as under bending loads. However, there is a lack of research combining both axisymmetric and bending loads, as also in the study of the strains in the tensile amour layers of the pipes, aspects which are important for the calibration of theoretical models to predict such behavior. Based on that, this study aims to evaluate the local behavior of flexible pipes under combinations of axisymmetric (tension, and internal pressure) and bending loads via a series of experimental tests in a 9.13″ I.D pipe. In the experimental tests, the behavior of the pipe was studied for three load combinations: i) bending combined with tension; ii) bending combined with internal pressure; and iii) bending combined with tension and internal pressure. Based on these tests, the authors obtained the strains in the tensile armor layer, axial elongation due to tension, axial reaction forces due to internal pressure, and deflection due to bending. These measurements were used to calibrate a theoretical model devoted to simulate the pipe’s response, getting accurate results for stiffness and stresses of the pipe in each scenario.

scholarly journals From atomistic interfaces to dendritic patterns

2018 ◽  
Vol 376 (2113) ◽  
pp. 20170210 ◽  
Author(s):  
P. K. Galenko ◽  
D. V. Alexandrov
Keyword(s):  
Computational Modelling ◽  
Experimental Tests ◽  
Theoretical Models ◽  
Boundary Integral ◽  
Transport Processes ◽  
Atomic Scale ◽  
Theme Issue ◽  
Two Phase ◽  
Field Methods ◽  
Atomistic Modelling

Transport processes around phase interfaces, together with thermodynamic properties and kinetic phenomena, control the formation of dendritic patterns. Using the thermodynamic and kinetic data of phase interfaces obtained on the atomic scale, one can analyse the formation of a single dendrite and the growth of a dendritic ensemble. This is the result of recent progress in theoretical methods and computational algorithms calculated using powerful computer clusters. Great benefits can be attained from the development of micro-, meso- and macro-levels of analysis when investigating the dynamics of interfaces, interpreting experimental data and designing the macrostructure of samples. The review and research articles in this theme issue cover the spectrum of scales (from nano- to macro-length scales) in order to exhibit recently developing trends in the theoretical analysis and computational modelling of dendrite pattern formation. Atomistic modelling, the flow effect on interface dynamics, the transition from diffusion-limited to thermally controlled growth existing at a considerable driving force, two-phase (mushy) layer formation, the growth of eutectic dendrites, the formation of a secondary dendritic network due to coalescence, computational methods, including boundary integral and phase-field methods, and experimental tests for theoretical models—all these themes are highlighted in the present issue. This article is part of the theme issue ‘From atomistic interfaces to dendritic patterns’.

scholarly journals The visual cues that drive the self-assessment of body size: Dissociation between fixation patterns and the key areas of the body for accurate judgement

Body Image ◽  
2019 ◽  
Vol 29 ◽  
pp. 31-46 ◽  
Author(s):  
Kamila R. Irvine ◽  
Kristofor McCarty ◽  
Thomas V. Pollet ◽  
Katri K. Cornelissen ◽  
Martin J. Tovée ◽  
...  
Keyword(s):  
Body Size ◽  
Visual Cues ◽  
The Body ◽  
The Self ◽  
Self Assessment

On the Axisymmetric Response of a Damaged Flexible Pipe

2014 ◽  
Author(s):  
José Renato M. de Sousa ◽  
Carlos Magluta ◽  
Ney Roitman ◽  
George C. Campello
Keyword(s):  
Finite Element ◽  
Analytical Model ◽  
Load Capacity ◽  
High Stress ◽  
Experimental Tests ◽  
Theoretical Models ◽  
Experimental Measurements ◽  
Fe Model ◽  
Flexible Pipe ◽  
High Stress Concentration

This work focuses on the structural analysis of a damaged 9.13″ flexible pipe to pure and combined axisymmetric loads. A set of experimental tests was carried out considering one up to ten broken wires in the outer tensile armor of the pipe and the results obtained are compared to those provided by a previously presented finite element (FE) model and a traditional analytical model. In the experimental tests, the pipe was firstly subjected to pure tension and, then, the responses to clockwise and anti-clockwise torsion superimposed with tension were investigated. In these tests, the induced strains in the outer armor were measured. Moreover, the axial elongation of the pipe was monitored when the pipe is subjected to tension, whilst the twist of the pipe was measured when torsion is imposed. The experimental results pointed to a slight decrease in the stiffness of the pipe with the increasing number of broken wires and, furthermore, a redistribution of forces among the intact wires of the damaged layer with high stress concentration in the wires close to the damaged ones. Both theoretical models captured these features, but, while the results obtained with the FE model agreed well with the experimental measurements, the traditional analytical model presented non-conservative results. Finally, the results obtained are employed to estimate the load capacity of the pipe.

scholarly journals Application of DIC Method in the Analysis of Stress Concentration and Plastic Zone Development Problems

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3460 ◽  
Author(s):  
Paweł J. Romanowicz ◽  
Bogdan Szybiński ◽  
Mateusz Wygoda
Keyword(s):  
Heat Treatment ◽  
Stress Concentration ◽  
High Strength Steels ◽  
High Strength ◽  
Experimental Tests ◽  
Theoretical Models ◽  
Material Behavior ◽  
Image Correlation ◽  
Stress Concentrations ◽  
Element Analysis

The paper presents the assessment of the possibility and reliability of the digital image correlation (DIC) system for engineering and scientific purposes. The studies were performed with the use of samples made of the three different materials—mild S235JR + N steel, microalloyed fine-grain S355MC steel, and high strength 41Cr4 steel subjected to different heat-treatment. The DIC studies were focused on determinations of dangerous zones with large stress concentrations, plastic deformation growth, and prediction of the failure zone. Experimental tests were carried out for samples with different notches (circular, square, and triangular openings). With the use of the DIC system and microstructure analyses, the influence of different factors (laser cutting, heat treatment, material type, notch shape, and manufacturing quality) on the material behavior were studied. For all studied cases, the stress concentration factors (SCF) were estimated with the use of the analytical formulation and the finite element analysis. It was observed that the theoretical models for calculations of the influence of the typical notches may result in not proper values of SCFs. Finally, the selected results of the total strain distributions were compared with FEM results, and good agreement was observed. All these allow the authors to conclude that the application of DIC with a common digital camera can be effectively applied for the analysis of the evolution of plastic zones and the damage detection for mild high-strength steels, as well as those normalized and quenched and tempered at higher temperatures.

scholarly journals Resilience of athletes: a systematic review based on a citation network analysis

2020 ◽  
Vol 20 (3) ◽  
pp. 26-40
Author(s):  
Camila cristina Fonseca bicalho ◽  
Gislane Ferreira de Melo ◽  
Franco Noce
Keyword(s):  
Systematic Review ◽  
Network Analysis ◽  
Web Of Science ◽  
Citation Network ◽  
Theoretical Models ◽  
Sport Performance ◽  
Individual Characteristics ◽  
Psychological Resilience ◽  
Citation Network Analysis ◽  
Academic Publications

The aims of the present study are to understand indicators and the scope of theoretical models adopted to describe athletes’ resilience, as well as to analyze their impact on investigations about such resilience. A search for original academic publications within a 10-year period was conducted in the PubMed / Medline, Web of Science, Taylor and Francis, Lilacs, Scopus, Humam Kinects and Science Direct databases, to substantiate a systematic literature review on athletes’ resilience. Articles were analyzed based on their methodological characteristics and citation network analysis. In total, 47 articles were identified and the most referenced one was Fletcher and Sarkar (2012), which was followed by Galli and Vealey (2008). The Grounded Theory of Psychological Resilience and Optimal Sport Performance by Fletcher and Sarkar (2012) seems to encompass the basic theoretical elementary aspects to better understand athletes’ resilience, so far. To conclude resilience is an on-going dynamic process based on individual characteristics and interactions with the environment.

Sign in / Sign up

Export Citation Format

Share Document