On the lubrication characteristics of piston ring under different engine operation conditions

2019 ◽  
Vol 72 (1) ◽  
pp. 101-108
Author(s):  
Jun Sun ◽  
Xiao Zhang ◽  
Jianxiong Zhu ◽  
Yaming Gao ◽  
Hu Wang ◽  
...  
Keyword(s):  
Piston Ring ◽  
Cylinder Liner ◽  
Operating Conditions ◽  
Lubricating Oil ◽  
Cylinder Wall ◽  
Engine Operation ◽  
Operating Condition ◽  
Content Type ◽  
Lubrication Characteristics ◽  
Stroke Engine

Purpose Currently, lubrication analysis of piston ring is generally done under engine rated operating condition. However, the engine (such as the vehicle engine) does not always operate in rated operating condition, and its operating condition changes frequently in actual use. In addition, the lubrication status of piston ring is generally assumed as the flooded lubrication or a certain form of poor lubrication in most of the lubrication analysis. Design/methodology/approach In this paper, based on the equations about the flow rate of lubricating oil and the variation of control volume, the flow model of lubricating oil in the piston ring-cylinder liner conjunction is established. The lubrication analysis of piston ring for a four-stroke engine under different engine operating conditions is done, in which the lubricating oil at the inlet of piston ring is considered as the lubricating oil attached on the relevant location of cylinder wall after the piston ring moves over at the previous stroke. Findings There is remarkable difference for the lubrication characteristics of the piston ring under different engine operating conditions. The worst lubrication status of piston ring may not take place under engine rated operating condition. Originality/value In this paper, based on the measured engine cylinder pressure, the lubrication analysis of piston ring for a four-stroke engine under different engine operating conditions is done in which the lubricating oil supply condition at the inlet of piston ring is considered. The results of this paper are helpful for the design and research of engine piston ring-cylinder liner conjunction.

A Spectrographic Sampling Method for Quick Assessment of Cylinder and Piston Ring Wear

1968 ◽  
Vol 90 (1) ◽  
pp. 43-48
Author(s):  
H. U. Wisniowski ◽  
D. R. Jackson
Keyword(s):  
Rapid Method ◽  
Sampling Method ◽  
Piston Ring ◽  
Cylinder Liner ◽  
Small Sample ◽  
Operating Conditions ◽  
Small Hole ◽  
Cylinder Wall ◽  
Lubricating Oils ◽  
Wear Rates

A simple, inexpensive, and rapid method of assessing cylinder and piston ring wear was developed. A small sample of the oil which lubricates the cylinder wall and piston rings was drawn off through a small hole in the cylinder wall. The sample was then analyzed spectrographically. Changes in wear resulting from changes in cylinder liner materials, fuels, lubricating oils, and other operating conditions were investigated. The method was found useful especially in cases of drastic differences in the wear rates. Selected examples of these studies are reported.

scholarly journals Investigation on the application of YAG laser texturing technology to the cylinder wall of auto engine

2014 ◽  
Vol 66 (3) ◽  
pp. 387-392 ◽  
Author(s):  
Jian Zhan ◽  
Mingjiang Yang
Keyword(s):  
Wear Rate ◽  
Piston Ring ◽  
Discrete Distribution ◽  
Cylinder Liner ◽  
Cylinder Wall ◽  
Laser Texturing ◽  
Yag Laser ◽  
Content Type ◽  
The Coefficient Of Friction ◽  
Lubrication Condition

Purpose – The purpose of this study was to develop a new approach using a pulse YAG laser with rational power density and pulse width to texture desired discrete distribution morphology on the cylinder wall. Design/methodology/approach – Variational rules of the effects of these three parameters were found by calculating the oil film on the cylinder/piston ring system. The experiment results were compared between laser texturing cylinders and conventional honing cylinders. Findings – It was found that the coefficient of friction and wear rate of laser texturing cylinders were reduced by 50 and 85.7 per cent, respectively, and the piston ring wear rate was decreased by 50 per cent under full lubrication condition. Under starved lubrication condition, the cylinder liner wear was reduced by 34.3 per cent. Originality/value – The effectiveness of which was determined by three control parameters: depth-to-diameter ratio, area density and distribution angle of the dimples.

Mutual influence of plateau roughness and groove texture of honed surface on frictional performance of piston ring–liner system

2016 ◽  
Vol 231 (7) ◽  
pp. 838-859 ◽  
Author(s):  
Yang Hu ◽  
Xianghui Meng ◽  
Youbai Xie ◽  
Jiazheng Fan
Keyword(s):  
Piston Ring ◽  
Cylinder Liner ◽  
Texture Features ◽  
Groove Depth ◽  
Mixed Lubrication ◽  
Operating Conditions ◽  
Friction Reduction ◽  
Lubrication Performance ◽  
Liner System ◽  
Frictional Performance

The cylinder liner surface finish, which is commonly produced using the honing technique, is an essential factor of engine performance. The characteristics of the texture features, including the cross-hatch angle, the plateau roughness and the groove depth, significantly affect the performance of the ring pack–cylinder liner system. However, due to the influence of the honed texture features, the surface roughness of the liner is not subject to Gaussian distribution. To simulate the mixed lubrication performance of the ring–liner system with non-Gaussian roughness, the combination of a two-scale homogenization technique and a deterministic asperities contact method is adopted. In this study, a one-dimensional homogenized mixed lubrication model is established to study the influence of groove parameters on the load-carrying capacity and the frictional performance of the piston ring–liner system. The ring profile, plateau roughness, and operating conditions are taken into consideration. The main findings are that for nonflat ring, shallow and wide groove textures are beneficial for friction reduction, and there exists an optimum groove density that makes the friction minimum; for flat ring, wide and sparse grooves help improving the tribological performance, and there exists an optimum groove depth that makes the friction minimum.

scholarly journals Wear of different material pairings for the cylinder liner – piston ring contact

2018 ◽  
Vol 70 (4) ◽  
pp. 687-699 ◽  
Author(s):  
Thomas Wopelka ◽  
Ulrike Cihak-Bayr ◽  
Claudia Lenauer ◽  
Ferenc Ditrói ◽  
Sándor Takács ◽  
...  
Keyword(s):  
Steady State ◽  
Wear Mechanisms ◽  
Piston Ring ◽  
Cylinder Liner ◽  
Wear Behaviour ◽  
Special Focus ◽  
Intermediate Step ◽  
Piston Rings ◽  
Content Type ◽  
Cylinder Liners

Purpose This paper aims to investigate the wear behaviour of different materials for cylinder liners and piston rings in a linear reciprocating tribometer with special focus on the wear of the cylinder liner in the boundary lubrication regime. Design/methodology/approach Conventional nitrided steel, as well as diamond-like carbon and chromium nitride-coated piston rings, were tested against cast iron, AlSi and Fe-coated AlSi cylinder liners. The experiments were carried out with samples produced from original engine parts to have the original surface topography available. Radioactive tracer isotopes were used to measure cylinder liner wear continuously, enabling separation of running-in and steady-state wear. Findings A ranking of the material pairings with respect to wear behaviour of the cylinder liner was found. Post-test inspection of the cylinder samples by scanning electron microscopy (SEM) revealed differences in the wear mechanisms for the different material combinations. The results show that the running-in and steady-state wear of the liners can be reduced by choosing the appropriate material for the piston ring. Originality/value The use of original engine parts in a closely controlled tribometer environment under realistic loading conditions, in conjunction with continuous and highly sensitive wear measurement methods and a detailed SEM analysis of the wear mechanisms, forms an intermediate step between engine testing and laboratory environment testing.

Field-Testing of Biodiesel (B100) and Diesel-Fueled Vehicles: Part 3—Wear Assessment of Liner and Piston Rings, Engine Deposits, and Operational Issues

2020 ◽  
Vol 143 (4) ◽  
Author(s):  
Avinash Kumar Agarwal ◽  
Deepak Agarwal
Keyword(s):  
Piston Ring ◽  
Direct Injection ◽  
Cylinder Liner ◽  
Field Testing ◽  
Field Trials ◽  
Operating Conditions ◽  
Piston Rings ◽  
Carbon Deposits ◽  
Bottom Dead Center ◽  
Operational Issues

Abstract This study investigated the use of biodiesel (B100) and baseline mineral diesel in two identical unmodified vehicles to realistically assess different aspects of biodiesel’s compatibility and durability issues with modern common rail direct injection (CRDI) engine-powered vehicles. Two identical vehicles were operated for 30,000 km under identical operating conditions during a field-trial using biodiesel (B100) and mineral diesel. Exhaustive experimental results from this series of tests are divided into four sections, and this is the third paper of this series of four papers, which covers comparative feasibility and wear analyses, underlining the effect of long-term use of biodiesel on wear of cylinder liner and piston rings compared to baseline mineral diesel-fueled vehicle. Surface microstructures at three locations of the cylinder liner were evaluated using scanning electron microscopy (SEM). Wear was found to be relatively lower at all locations of liners from biodiesel-fueled vehicle compared to diesel-fueled vehicle. Surface roughness of cylinder liners measured at different locations showed that it reduced by ∼30–40% at top dead center (TDC), ∼10–20% at mid-stroke, and ∼20–30% at bottom dead center (BDC) for both vehicles, showing higher wear close to TDC compared to mid-stroke and BDC locations. Loss of piston-ring weight was significantly lower for biodiesel-fueled vehicle. Engine tear-down observations and carbon deposits on various engine components were recorded after the conclusion of the field trials. During these field-trials, engine durability-related issues such as fuel-filter plugging, injector coking, piston-ring sticking, carbon deposits in the combustion chamber, and contamination of lubricating oils were found to be relatively lower in biodiesel-fueled vehicle. Overall, no noticeable durability issues were recorded because of the use of biodiesel in CRDI engine-powered vehicle.

Simulation of Altitude Influence on Piston Ring Movement and Blow-By Effects in Piston Engines (Keynote)

2003 ◽  
Author(s):  
Sylvester Abanteriba
Keyword(s):  
Combustion Chamber ◽  
Piston Ring ◽  
Cylinder Liner ◽  
Lubricating Oil ◽  
Axial Position ◽  
Piston Engine ◽  
Piston Rings ◽  
Ability To Act ◽  
Effective Seal ◽  
The Impact

The compression and oil rings of the piston engine play a very important role in the performance and reliability of the piston engine. The rings are required to accomplish three main distinct tasks: 1. Sealing the combustion chamber gas from the crankcase to eliminate blow-by phenomenon, which constitutes the flow of some of the contents of the combustion chamber into the crankcase. 2. Proper distribution of the lubricating oil film over the piston skirt and cylinder liner. 3. Transfer of heat from piston to cylinder liner. Unfortunately the piston ring pack contributes to the highest proportion of the frictional losses in the engine and is more prone to high wear rates. In the engine, the compression rings are designed to provide effective sealing of the crankcase against the gases from the combustion chamber. The oil-rings provide an effective means of distributing the lubricating oil over the cylinder liner while keeping it from flowing into the combustion chamber. The ability of the compression rings to serve as a gas seal depends on their axial position within the groove. The ring needs to be in contact with the lower flank in order to provide the requisite sealing effect. Once the ring lifts itself from the lower flank its ability to act as an effective seal is compromised. The axial motion of the piston rings during the operation of the engine engenders blow-by and therefore has deteriorating effect on the engine performance. Not much work has, hereto, been done to study the impact of altitude on the movement of the piston rings and hence the blow-by phenomenon. This papers presents a simulation model to investigate this effect.

Influence of positive texturing on friction and wear properties of piston ring-cylinder liner tribo pair under lubricated conditions

2019 ◽  
Vol 71 (4) ◽  
pp. 515-524 ◽  
Author(s):  
Venkateswara Babu P. ◽  
Ismail Syed ◽  
Satish Ben Beera
Keyword(s):  
Wear Resistance ◽  
Internal Combustion Engine ◽  
Friction And Wear ◽  
Piston Ring ◽  
Combustion Engine ◽  
Cylinder Liner ◽  
Internal Combustion ◽  
Tribological Performance ◽  
Friction Reduction ◽  
Content Type

Purpose In an internal combustion engine, piston ring-cylinder liner tribo pair is one among the most critical rubbing pairs. Most of the energy produced by an internal combustion engine is dissipated as frictional losses of which major portion is contributed by the piston ring-cylinder liner tribo pair. Hence, proper design of tribological parameters of piston ring-cylinder liner pair is essential and can effectively reduce the friction and wear, thereby improving the tribological performance of the engine. This paper aims to use surface texturing, an effective and feasible method, to improve the tribological performance of piston ring-cylinder liner tribo pair. Design/methodology/approach In this paper, influence of positive texturing (protruding) on friction reduction and wear resistance of piston ring surfaces was studied. The square-shaped positive textures were fabricated on piston ring surface by chemical etching method, and the experiments were conducted with textured piston ring surfaces against un-textured cylinder liner surface on pin-on-disc apparatus by continuous supply of lubricant at the inlet of contact zone. The parameters varied in this study are area density and normal load at a constant sliding speed. A comparison was made between the tribological properties of textured and un-textured piston ring surfaces. Findings From the experimental results, the tribological performance of the textured piston ring-cylinder liner tribo pair was significantly improved over a un-textured tribo pair. A maximum friction reduction of 67.6 per cent and wear resistance of 81.6 per cent were observed with textured ring surfaces as compared to un-textured ring surfaces. Originality/value This experimental study is helpful for better understanding of the potency of positive texturing on friction reduction and wear resistance of piston ring-cylinder liner tribo pair under lubricated sliding conditions.

Effects of different surface grooved cylinder liner on the tribological performance for cylinder liner-piston ring components

2019 ◽  
Vol 72 (5) ◽  
pp. 581-588
Author(s):  
Jiazhi Miao ◽  
Yongqing Li ◽  
Xiang Rao ◽  
Libao Zhu ◽  
Zhiwei Guo ◽  
...  
Keyword(s):  
Piston Ring ◽  
Critical Factor ◽  
Cylinder Liner ◽  
Content Type ◽  
Crucial Effect ◽  
Design And Manufacturing ◽  
Marine Engines ◽  
Marine Diesel ◽  
Energy Economy ◽  
Groove Texture

Purpose The emission from marine engines has a crucial effect on energy economy and environment pollution. One of the effective emission reduction schemes is to minimize the friction loss of main friction pairs such as cylinder liner-piston ring (CLPR). Micro-groove textures were designed to accomplish this aim. Design/methodology/approach The authors experimentally investigated the effects of micro-groove textures at different cylinder liner positions. The micro-groove texture was fabricated on samples by chemical etching and cut from the real CLPR pair. Sliding contact tests were conducted by a reciprocation test apparatus. Findings The average friction coefficient of grooves at 30° inclination were reduced up to 58.22% and produced better tribological behavior at most conditions. The operating condition was the critical factor that determined the optimum texture pattern. The surface morphology indicated that textures could produce smoother surfaces and less scratches as compared with the untextured surface. Originality/value Inclined grooves and V-grooves were designed and applied to real CLPR pairs. The knowledge obtained in this study will lead to practical basis for tribological design and manufacturing of CLPR pair in marine diesel engines.

Surface and wear mechanisms analysis of phosphorous-free and conventional engine lubricants on cylinder liner and piston rings surfaces

2015 ◽  
Vol 67 (5) ◽  
pp. 441-448 ◽  
Author(s):  
Dogus Özkan ◽  
Hakan Kaleli ◽  
Yves BERTHIER ◽  
Levent Yüksek
Keyword(s):  
Wear Mechanisms ◽  
Cylinder Liner ◽  
Antiwear Additive ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Piston Rings ◽  
Additive Package ◽  
Content Type ◽  
Lubrication Oil ◽  
Endurance Tests

Purpose – This paper aims to investigate the wear mechanisms, formations and effectiveness of tribofilms of new developed, antiwear additive which is called mercapthocarboxylate. The mercapthocarboxylate is a sulphur-based and non-phosphorus additive. Design/methodology/approach – The effectiveness of the additive was examined through a set of laboratory endurance tests that applied with single cylinder spark ignition engine. Two types of lubricants were used to compare the engine tests which were thiophosphate (ZDDP) containing engine lubricant (phosphorus containing) and mercapthocarboxylate containing non-phosphorus and non-ash crankcase oil. Lubricants were tested under identical operating conditions for 100 hrs. The surfaces of cylinder liner and piston rings were inspected through optical microscopy, scanning electron microscopy and energy dispersive X-ray spectroscopy techniques. Findings – Catalysis-friendly and sulphur-based mercapthocarboxylate additive can be an alternative antiwear additive package for lubrication oil due to better wear performance when compared to ZDDP. Originality/value – Sulphur-based mercapthocarboxylate is a new developed antiwear additive and was applied to lubrication oil in this study. This lubrication oil was tested in the real engine environment by using 100-hr engine bench tests.

Microstructure and tribological properties of sprayed nanostructure Fe-based martensite coating on an aluminum cylinder liner

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Eryong Liu ◽  
Yuan Xue ◽  
Yaping Bai ◽  
Jibin Pu ◽  
Shuangming Du ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Tribological Properties ◽  
Cylinder Liner ◽  
Adhesive Force ◽  
Lubricating Oil ◽  
Strengthening Effect ◽  
Content Type ◽  
Fine Grain ◽  
Strong Adhesion ◽  
Aluminum Cylinder

Purpose The purpose of this paper is to improve the tribological properties of aluminum cylinder liner. Higher martensite contents were closely related to the higher hardness and excellent wear resistance of Fe-based coatings. Furthermore, the grain size of the Fe-based coating was approximately 40 nm, which provides an excellent fine grain strengthening effect. Design/methodology/approach To improve the tribological properties of aluminum cylinder liners, a Fe-based martensite coating was prepared by internal plasma spraying technology, whose microstructure and tribological properties were then investigated. Findings Sprayed Fe-based coating possessed a low contact angle and strong adhesion with lubricating oil. In a simulated engine condition, Fe-based coating exhibited a decreased friction coefficient and increased wear resistance under oil lubrication, which was dominated by a stronger adhesive force with lubricating oil, higher martensite contents on the worn surface, higher hardness and higher H/E value than those of the reference HT 200 and Al-19Si cylinder material. Originality/value Nanostructure Fe-based martensite coating was sprayed on an aluminum cylinder liner, which demonstrated remarkable advantages over the reference cylinder material.

Sign in / Sign up

Export Citation Format

Share Document