Numerical and experimental investigations on the wear behavior of water-lubricated bearings with different materials

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Liwu Wang ◽  
Yanfeng Han ◽  
Dongxing Tang ◽  
Jianlin Cai
Keyword(s):  
Friction And Wear ◽  
Wear Behavior ◽  
Wear Test ◽  
Coupling Model ◽  
Mixed Lubrication ◽  
Experimental Results ◽  
Experimental Investigations ◽  
Wear Depth ◽  
Content Type ◽  
Polyether Ether Ketone

Purpose The purpose of this paper is to verify the effectiveness of the proposed transient mixed lubrication and wear coupling model [mixed lubrication and wear (MLW) coupling model] under water lubricated conditions by comparing with the experimental results. Design/methodology/approach Water lubricated bearings are the key parts of the transmission system of an underwater vehicle and some surface ships. In this study, the friction and wear behaviors of rubber, nylon and polyether ether ketone (PEEK) samples with stainless steel underwater lubrication were compared by using ring-block contact structure on multifunctional friction and wear test bench-5000 friction and wear tester. Findings The results show that the transient wear depth and wear amount of PEEK, nylon and rubber samples under water lubrication are in good agreement with the calculated results of the theoretical model, which verifies the rationality and scientific nature of the MLW coupling model. Thus, the numerical model is applicable for the wear prediction of the journal bearing under water-lubricated conditions. Furthermore, numerical and experimental results reveal that the anti-wear performance among three water-lubricated materials can be ranked by: PEEK > nylon > rubber. Originality/value It is expected that this study can provide more information for experimental and numerical research of water-lubricated bearings under water-lubricated conditions.

Control on wear of journal bearing operating in mixed lubrication regime using grooving arrangements

2016 ◽  
Vol 68 (4) ◽  
pp. 458-465 ◽  
Author(s):  
Lijesh K.P. ◽  
Muzakkir S.M. ◽  
Harish Hirani ◽  
Gananath Doulat Thakre
Keyword(s):  
Journal Bearing ◽  
Wear Behavior ◽  
Research Work ◽  
Theory Model ◽  
Mixed Lubrication ◽  
Experimental Investigations ◽  
Heavy Load ◽  
Content Type ◽  
Lubrication Regime ◽  
Mixed Lubrication Regime

Purpose The journal bearings subjected to heavy load and slow speed operate in mixed lubrication regime causing contact between the interacting surfaces and resulting in wear. Complexity of wear behavior and lack of unifying theory/model make wear-control very challenging. Design/methodology/approach In the present research work, theoretical and experimental investigations have been conducted to explore the effect of grooving arrangements on the wear behavior of journal bearing operating in mixed lubrication regime. The theoretical model of Hirani (2005) that uses mass conserving cavitation algorithm has been used to determine the bearing eccentricity for different groove arrangements (with varying groove location and extent) for identifying a groove arrangement that minimizes the wear. The wear tests on the grooved bearings were conducted after suitable running-in of the new bearings on a fully automated journal bearing test set-up. A load and speed combination required to operate the bearing in mixed lubrication was used. The performance of different arrangement of bearing was evaluated by measuring their weight loss after the test. Findings Wear was significantly reduced with the use of proper groove arrangement for a bearing operating in mixed lubrication regime. Originality/value The improvement in bearing performance by providing grooves has been the subject matter of several studies in the past, but these studies were confined to the hydrodynamic operative regime of the bearing. In the present work, seven different combinations of axial and radial groove arrangement were tried, which has not been reported in any other work.

scholarly journals Impact-sliding wear response of 2.25Cr1Mo steel tubes: Experimental and semi-analytical method

Friction ◽  
2021 ◽  
Author(s):  
Meigui Yin ◽  
Chaise Thibaut ◽  
Liwen Wang ◽  
Daniel Nélias ◽  
Minhao Zhu ◽  
...  
Keyword(s):  
Sliding Wear ◽  
Power Plants ◽  
Mechanical Response ◽  
Wear Behavior ◽  
Wear Test ◽  
Steel Tube ◽  
Wear Depth ◽  
Sliding Velocity ◽  
Friction Forces ◽  
The Impact

AbstractThe impact-sliding wear behavior of steam generator tubes in nuclear power plants is complex owing to the dynamic nature of the mechanical response and self-induced tribological changes. In this study, the effects of impact and sliding velocity on the impact-sliding wear behavior of a 2.25Cr1Mo steel tube are investigated experimentally and numerically. In the experimental study, a wear test rig that can measure changes in the impact and friction forces as well as the compressive displacement over different wear cycles, both in real time, is designed. A semi-analytical model based on the Archard wear law and Hertz contact theory is used to predict wear. The results indicate that the impact dynamic effect by the impact velocity is more significant than that of the sliding velocity, and that both velocities affect the friction force and wear degree. The experimental results for the wear depth evolution agree well with the corresponding simulation predictions.

Tribological behavior of AA7075-TiC composites by powder metallurgy

2018 ◽  
Vol 70 (6) ◽  
pp. 1066-1071 ◽  
Author(s):  
Saravanan C. ◽  
Subramanian K. ◽  
Anandakrishnan V. ◽  
Sathish S.
Keyword(s):  
Powder Metallurgy ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Tribological Behavior ◽  
Wear Behavior ◽  
Process Condition ◽  
Wear Test ◽  
Matrix Composites ◽  
Content Type ◽  
Weight Percentage

Purpose Aluminium is the most preferred material in engineering structural components because of its excellent properties. Furthermore, the properties of aluminium may be enhanced through metal matrix composites and an in-depth investigation on the evolved properties is needed in view of metallurgical, mechanical and tribological aspects. The purpose of this study is to explore the effect of TiC addition on the tribological behavior of aluminium composites. Design/methodology/approach Aluminium metal matrix composites at different weight percentage of titanium carbide were produced through powder metallurgy. Produced composites were subjected to sliding wear test under dry condition through Taguchi’s L9 orthogonal design. Findings Optimal process condition to achieve the minimum wear rate was identified though the main effect plot. Sliding velocity was identified as the most dominating factor in the wear resistance. Practical implications The production of components with improved properties is promoted efficiently and economically by synthesizing the composite via powder metallurgy. Originality/value Though the investigations on the wear behavior of aluminium composites are analyzed, reinforcement types and the mode of fabrication have their significance in the metallurgical and mechanical properties. Thus, the produced component needs an in-detail study on the property evolution.

Investigation of thermochemical boriding effect on wear behavior of a GGG 50 quality as-cast ductile iron

2016 ◽  
Vol 68 (4) ◽  
pp. 476-481 ◽  
Author(s):  
Harun Mindivan
Keyword(s):  
Wear Resistance ◽  
Abrasive Wear ◽  
Ductile Iron ◽  
Room Temperature ◽  
Wear Behavior ◽  
Surface Hardness ◽  
Wear Test ◽  
Content Type ◽  
Pin On Disc ◽  
Cast Ductile Iron

Purpose This study aims to investigate the microstructure and the abrasive wear features of the untreated and pack borided GGG 50 quality ductile iron under various working temperatures. Design/methodology/approach GGG 50 quality as-cast ductile iron samples were pack borided in Ekabor II powder at 900°C for 3 h, followed by furnace cooling. Structural characterization was made by optical microscopy. Mechanical characterization was made by hardness and pin-on-disc wear test. Pin-on-disc test was conducted on a 240-mesh Al2O3 abrasive paper at various temperatures in between 25 and 450°C. Findings Room temperature abrasive wear resistance of the borided ductile iron increased with an increase in its surface hardness. High-temperature abrasive wear resistances of the borided ductile iron linearly decreased with an increase in test temperature. However, the untreated ductile iron exhibited relatively high resistance to abrasion at a temperature of 150°C. Originality/value This study can be a practical reference and offers insight into the effects of boriding process on the increase of room temperature wear resistance. However, above 150°C, the untreated ductile iron exhibited similar abrasive wear performance as compared to the borided ductile iron.

Research on Friction and Wear Behavior of Rubber in the Mixture of Crude Oil with Water

2013 ◽  
Vol 300-301 ◽  
pp. 1254-1258 ◽  
Author(s):  
Xiao Ren Lv ◽  
Xu Yao Huo ◽  
Guang Zu Qu ◽  
Shi Jie Wang
Keyword(s):  
Crude Oil ◽  
Water Content ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Frictional Coefficient ◽  
Water Film ◽  
Wear Test ◽  
Wear Behaviour ◽  
Wear Loss ◽  
Butadiene Rubber

In order to choose the rubber material and improve the service life of Progressing Cavity Pump (PCP ) when exploiting offshore crude oil, it is important to analyze friction and wear behaviour of stator and rotor of PCP in the mixture of crude oil with different water content. The friction and wear test about Nitrile -Butadiene Rubber (NBR) and Fluorine Rubber (FKM) were carried on ring-on-block tester, the wear loss was observed by electron microscope, the wear mechanism was also discussed. The results show that: (1) FKM owns better wearing resistance than NBR in the mixture of crude oil with different water content; (2) when the content of water in the mixture is less than 26%, the frictional coefficient of sample is 0.05, due to the oil film between the friction pairs; (3) when the content of water in the mixture is more than 26%, the frictional coefficient increases to 0.4, because of the water film between the friction pairs.

Tribological Characteristics of Surface Treatment for Piston Pin

2009 ◽  
Vol 79-82 ◽  
pp. 2199-2202 ◽  
Author(s):  
Joon Ho Seo ◽  
Jin Yong Kim ◽  
Seung Uk Park ◽  
Hyun Chul Kim ◽  
Byung Chul Na ◽  
...  
Keyword(s):  
Fuel Economy ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Wear Test ◽  
Measuring System ◽  
Optical Surface ◽  
Connecting Rod ◽  
Low Friction ◽  
Automotive Engine ◽  
The Face

The piston pin contact in a typical automotive engine is an example of a highly loaded. Therefore, for piston pin design several aspects are important. Among them are function, cost, NVH, fuel economy, durability, and impact on other design aspects of the engine. Continuously contacting with piston pin, the face of connecting rod, brings about abnormal wear such as unfairwear or earlywear. because the engine get more powered and one requirement for a good fuel economy is to achieve a low level of mechanical friction. In this study, modern low friction coatings and treatment at the piston pin interface aimed to investigate the potential. The profile of coated specimens were observed by non-contact type optical surface measuring system and the friction-wear behaviors of coated specimens were investigated by using piston pin wear tester. Piston pin wear test was performed to analyze the friction and wear behavior. The results showed that the application of low friction coatings and treatment effectively improved tribological performance of the piston pin

scholarly journals Modification of Surface Topography and Analysis of Its Impact on Friction and Wear Reduction of Sliding Contact

2019 ◽  
Vol 9 (1S3) ◽  
pp. 23-26
Keyword(s):  
Friction And Wear ◽  
Wear Behavior ◽  
Surface Texturing ◽  
Wear Test ◽  
Sliding Contact ◽  
Surface Textures ◽  
Sliding Direction ◽  
Pin On Disc ◽  
Interacting Surfaces ◽  
The Impact

Proper lubrication and surface modification are key factors to improve the tribological behavior of interacting sliding surfaces under lubricated conditions. Surface texturing of interacting surfaces has found to be an emerging technique that modifies the surfaces deterministically by producing surface features in the form of surface asperities or grooves with specific shape, size and distribution. The present paper address the impact of positive surface textures (protrusions) and number of positive textures in the sliding direction on friction and wear behavior of parallel sliding contacts. The square shaped positive surface textures are created on the specimen by ink-jet followed by chemical etching process. The sliding experiments are conducted on pin on disc friction and wear test rig by providing different sliding conditions such as plain dry, plain with lubricant and textures with lubricant between the interacting surfaces. The results indicated that the textures with lubricated condition exhibit lower friction and wear compared to other two conditions. Furthermore, it is reported that among the tested samples, the textured sample with number of textures three in sliding direction has shown a prominent effect in reducing friction and wear of parallel sliding contact.

Numerical Simulation of Combustion Resistant Titanium Alloy Wear Behavior at High Temperature Fields

2018 ◽  
Vol 913 ◽  
pp. 168-175
Author(s):  
Xian Ye Liang ◽  
Guang Bao Mi ◽  
Liang Ju He ◽  
Pei Jie Li
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Titanium Alloy ◽  
High Temperature ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Temperature Fields ◽  
Wear Depth ◽  
Disk Model ◽  
Pin On Disk

The abnormal local friction and wear phenomena usually generate during the service of the titanium alloy rotor /stator parts of the aero engine compressor under high temperature conditions. This phenomenon is the main cause of the occurrence of titanium fire failure and has great harm. In the present investigation the friction and wear behavior of the combustion resistant titanium alloy at high temperature was studied by finite element numerical simulation and experimental verification of the pin-on-disk model. Firstly, the geometrical model of the round bottom pin-on-disk contact was established. Then, the friction process was simulated by the Coulomb friction model. The ALE technique of ABAQUS was applied to move the contact nodes and update the grid. The finite element simulation of the ARCHARD wear model was realized. In order to deal with the increasing contact area, a simplify wear direction was proposed. Finally, the wear depth and volume was calculated and the wear law at 500 °C -900 °C was revealed. The results show that the wear process is gentle at the temperature of 500-700 °C, and the wear depth is within 0.08mm when the sliding distance reaches 1800m. When the temperature exceeds 800 °C, the wear rate increased sharply and the wear depth beyond 0.1mm, the FE result is consistent with the test results.

Friction and wear behavior of hydrogenated diamond-like carbon coating against titanium alloys under large normal load and variable velocity

2017 ◽  
Vol 69 (2) ◽  
pp. 199-207 ◽  
Author(s):  
Jun Liu ◽  
Zhinan Zhang ◽  
Zhe Ji ◽  
Youbai Xie
Keyword(s):  
Friction Coefficient ◽  
Service Life ◽  
Carbon Coating ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Normal Load ◽  
Diamond Like Carbon ◽  
Content Type ◽  
Friction And Wear Behavior ◽  
Dlc Coating

Purpose This paper aims to investigate the effects of reciprocating frequency, large normal load on friction and wear behavior of hydrogenated diamond-like carbon (H-DLC) coating against Ti-6Al-4V ball under dry and lubricated conditions. Design/methodology/approach The friction and wear mechanisms are analyzed by scanning electron microscope, energy dispersive spectroscopy and Raman spectroscopy. Findings The results show that as reciprocating frequency increases under lubricated conditions, the friction coefficient decreases first and then increases. When the reciprocating frequency is 2.54 Hz, the value of friction coefficient reaches the minimum. The friction reduction is because of the transformation from sp3 to sp2, the formation of transfer layer on Ti-6Al-4V ball and the reduction in viscous friction, whereas the increase of friction coefficient is related to wear. In dry conditions, the friction coefficient is between 0.06 and 0.1. And, the service life of H-DLC coating decreases with the increase in reciprocating frequency and normal load. Research limitations/implications It is confirmed that adding the lubricant could prolong the service life of H-DLC coating and reduce friction and wear efficiently. And, the wear mechanisms under dry and lubricated conditions encompass abrasive wear and adhesive wear. Originality/value The results are helpful for application of diamond-like carbon coating.

Wear behaviour of copper/carbon nanotubes

2017 ◽  
Vol 69 (3) ◽  
pp. 342-347 ◽  
Author(s):  
Nor Shamimi Shaari ◽  
Jamaliah Md Said ◽  
Aidah Jumahat ◽  
Muhammad Hussain Ismail
Keyword(s):  
Carbon Nanotubes ◽  
Wear Test ◽  
Hardness Test ◽  
Copper Matrix ◽  
Wear Behaviour ◽  
Wear Depth ◽  
Wear Properties ◽  
Test Analysis ◽  
Content Type ◽  
Pure Cu

Purpose The purpose of this paper is to study the wear behaviour of copper matrix composites reinforced with carbon nanotubes (CNTs) prepared by powder metallurgy route. Design/methodology/approach The CNTs were treated by sulphuric acid and nitric acid to deagglomerate the CNTs prior mixing with copper powder. The composites comprised 0 to 4 Vol.% pristine CNTs (PCNTs) and also after acid-treated CNTs (ACNTs). The optimum value (pure Cu, 3 Vol.% PCNTs, 3 Vol.% ACNTs) evaluated by micro-hardness test was selected for wear test analysis. Findings The results showed that the enhancement of hardness, weight loss, coefficient of friction, wear depth and surface roughness (Ra) was due to the effect of homogenous distribution of ACNTs in Cu matrix and significant bonding compared to pure Cu and Cu-reinforced PCNTs. The scanning electron microscopy micrograph of worn surfaces and wear depth of the specimens also showed that the addition of ACNTs in Cu resulted in better wear performances. Originality/value CNTs were treated prior processing to improve hardness and wear properties of Cu/CNTs composites.

Sign in / Sign up

Export Citation Format

Share Document