An approach for mechanical property optimization of fused deposition modeling with polylactic acid via design of experiments

2016 ◽  
Vol 22 (2) ◽  
pp. 387-404 ◽  
Author(s):  
Jonathan Torres ◽  
Matthew Cole ◽  
Allen Owji ◽  
Zachary DeMastry ◽  
Ali P. Gordon
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Fused Deposition Modeling ◽  
Mechanical Tests ◽  
Content Type ◽  
Fused Deposition ◽  
Structural Applications ◽  
3D Printers ◽  
Deposition Modeling

Purpose This paper aims to present the influences of several production variables on the mechanical properties of specimens manufactured using fused deposition modeling (FDM) with polylactic acid (PLA) as a media and relate the practical and experimental implications of these as related to stiffness, strength, ductility and generalized loading. Design/methodology/approach A two-factor-level Taguchi test matrix was defined to allow streamlined mechanical testing of several different fabrication settings using a reduced array of experiments. Specimens were manufactured and tested according to ASTM E8/D638 and E399/D5045 standards for tensile and fracture testing. After initial analysis of mechanical properties derived from mechanical tests, analysis of variance was used to infer optimized production variables for general use and for application/load-specific instances. Findings Production variables are determined to yield optimized mechanical properties under tensile and fracture-type loading as related to orientation of loading and fabrication. Practical implications The relation of production variables and their interactions and the manner in which they influence mechanical properties provide insight to the feasibility of using FDM for rapid manufacturing of components for experimental, commercial or consumer-level use. Originality/value This paper is the first report of research on the characterization of the mechanical properties of PLA coupons manufactured using FDM by the Taguchi method. The investigation is relevant both in commercial and consumer-level aspects, given both the currently increasing utilization of 3D printers for component production and the viability of PLA as a renewable, biocompatible material for use in structural applications.

Effect of Printing Parameters on the Mechanical Properties of Parts Fabricated with Open-Source 3D Printers in PLA by Fused Deposition Modeling

2020 ◽  
Vol 22 (4) ◽  
pp. 895-908
Author(s):  
M. Ouhsti ◽  
B. El Haddadi ◽  
S. Belhouideg
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
3D Printers ◽  
Deposition Modeling ◽  
Printed Materials ◽  
Printing Parameters

Abstract3D polymer-based printers have become easily accessible to the public. Usually, the technology used by these 3D printers is Fused Deposition Modelling (FDM). The majority of these 3D printers mainly use acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA) to fabricate 3D objects. In order for the printed parts to be useful for specific applications, the mechanical properties of the printed parts must be known. The aim of this study is to determine the tensile strength and elastic modulus of printed materials in polylactic acid (PLA) according to three important printing parameters such as deposition angle, extruder temperature and printing speed. The central composite design (CCD) was used to reduce the number of tensile test experiments. The obtained results show that the mechanical properties of printed parts depend on printing parameters. Empirical models relating response and process parameters are developed. The analysis of variance (ANOVA) was used to test the validity of models relating response and printing parameters. The optimal printing parameters are determined for the desired mechanical properties.

Synthesis and properties of modified PBT for FDM

2017 ◽  
Vol 23 (4) ◽  
pp. 804-810 ◽  
Author(s):  
Shiqing Cao ◽  
Dandan Yu ◽  
Weilan Xue ◽  
Zuoxiang Zeng ◽  
Wanyu Zhu
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Fused Deposition Modeling ◽  
Complex Structure ◽  
Three Dimensional ◽  
Sebacic Acid ◽  
Wire Drawing ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling

Purpose The purpose of this paper is to prepare a new modified polybutylene terephalate (MPBT) for fused deposition modeling (FDM) to increase the variety of materials compatible with printing. And the printing materials can be used to print components with a complex structure and functional mechanical parts. Design/methodology/approach The MPBT, poly(butylene terephalate-co-isophthalate-co-sebacate) (PBTIS), was prepared for FDM by direct esterification and subsequent polycondensation using terephthalic acid (PTA), isophthalic acid (PIA), sebacic acid (SA) and 1,4-butanediol (BDO). The effects of the content of PIA (20-40 mol%) on the mechanical properties of PBTIS were investigated when the mole per cent of SA (αSA) is zero. The effects of αSA (0-7mol%) on the thermal, rheological and mechanical properties of PBTIS were investigated at nPTA/nPIA = 7/3. A desktop wire drawing and extruding machine was used to fabricate the filaments, whose printability and anisotropy were tested by three-dimensional (3D) printing experiments. Findings A candidate content of PIA introducing into PBT was obtained to be about 30 per cent, and the Izod notched impact strength of PBTIS increased with the increase of αSA. The results showed that the PBTIS (nPTA/nPIA = 7/3, αSA = 3-5mol%) is suitable for FDM. Originality/value New printing materials with good Izod notched impact strength were obtained by introducing PIA and SA (nPTA/nPIA = 7/3, αSA = 3-5 mol%) into PBT and their anisotropy are better than that of ABS.

Simulation of edge quality in fused deposition modeling

2019 ◽  
Vol 25 (3) ◽  
pp. 541-554 ◽  
Author(s):  
Antonio Armillotta
Keyword(s):  
Fused Deposition Modeling ◽  
Experimental Tests ◽  
Geometric Errors ◽  
Content Type ◽  
Fused Deposition ◽  
Graphical Simulation ◽  
Deposition Modeling ◽  
Edge Quality ◽  
Input Variables

Purpose The purpose of this paper is to propose a method for simulating the profile of part edges as a result of the FDM process. Deviations from nominal edge shape are predicted as a function of the layer thickness and three characteristic angles depending on part geometry and build orientation. Design/methodology/approach Typical patterns of edge profiles were observed on sample FDM parts and interpreted as the effects of possible toolpath generation strategies. An algorithm was developed to generate edge profiles consistent with the patterns expected for any combination of input variables. Findings Experimental tests confirmed that the simulation procedure can correctly predict basic geometric properties of edge profiles such as frequency, amplitude and shape of periodic asperities. Research limitations/implications The algorithm takes into account only a subset of the error causes recognized in previous studies. Additional causes could be integrated in the simulation to improve the estimation of geometric errors. Practical implications Edge simulation may help avoid process choices that result in aesthetic and functional defects on FDM parts. Originality/value Compared to the statistical estimation of geometric errors, graphical simulation allows a more detailed characterization of edge quality and a better diagnosis of error causes.

Deposition-induced effects of isotactic polypropylene and polycarbonate composites during fused deposition modeling

2017 ◽  
Vol 23 (5) ◽  
pp. 869-880 ◽  
Author(s):  
Ying-Guo Zhou ◽  
Bei Su ◽  
Lih-sheng Turng
Keyword(s):  
Mechanical Properties ◽  
Design Methodology ◽  
Fused Deposition Modeling ◽  
Content Type ◽  
Fused Deposition ◽  
Close Relationship ◽  
Molded Parts ◽  
Deposition Modeling ◽  
Injection Molded ◽  
First Time

Purpose Although the feasibility and effectiveness of the fused deposition modeling (FDM) method have been proposed and developed, studies of applying this technology to various materials are still needed for researching its applicability, especially with regard to polymer blends and composites. The purpose of this paper is to study the deposition-induced effect and the effect of compatibilizers on the mechanical properties of polypropylene and polycarbonate (PP/PC) composites. Design/methodology/approach For this purpose, three different deposition modes for PP/PC composites with or without compatibilizers were used for the FDM method and tested for tensile properties. Also, parts with the same materials were made by injection molding and used for comparison. In addition, different deposition speeds were used to investigate the different deposition-induced effects. Furthermore, the behavior of the mechanical properties was clarified with scanning electron microscope images of the fracture surfaces. Findings The research results suggest that the deposition orientation has a significant influence on the mechanical behavior of PP/PC composite FDM parts. The results also indicate that there is a close relationship between the mechanical properties and morphological structures which are deeply influenced by compatibilization. Compared with injection molded parts, the ductility of the FDM parts can be dramatically improved due to the formation of fibrils and micro-fibrils by the deposition induced during processing. Originality/value This is the first paper to investigate a PP/PC composite FDM process. The results of this paper verified the applicability of PP/PC composites to FDM technology. It is also the first time that the deposition-induced effect during FDM has been investigated and studied.

Effect of layer thickness on irreversible thermal expansion and interlayer strength in fused deposition modeling

2017 ◽  
Vol 23 (5) ◽  
pp. 943-953 ◽  
Author(s):  
Anthony A. D’Amico ◽  
Analise Debaie ◽  
Amy M. Peterson
Keyword(s):  
Mechanical Properties ◽  
Thermal Expansion ◽  
Flexural Strength ◽  
Layer Thickness ◽  
Fused Deposition Modeling ◽  
Thermal Strain ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
The Impact

Purpose The aim of this paper is to examine the impact of layer thickness on irreversible thermal expansion, residual stress and mechanical properties of additively manufactured parts. Design/methodology/approach Samples were printed at several layer thicknesses, and their irreversible thermal expansion, tensile strength and flexural strength were determined. Findings Irreversible thermal strain increases with decreasing layer thickness, up to 22 per cent strain. Tensile and flexural strengths exhibited a peak at a layer thickness of 200 μm although the maximum was not statistically significant at a 95 per cent confidence interval. Tensile strength was 54 to 97 per cent of reported values for injection molded acrylonitrile butadiene styrene (ABS) and 29 to 73 per cent of those reported for bulk ABS. Flexural strength was 18 to 41 per cent of reported flexural strength for bulk ABS. Practical implications The large irreversible thermal strain exhibited that corresponding residual stresses could lead to failure of additively manufactured parts over time. Additionally, the observed irreversible thermal strains could enable thermally responsive shape in additively manufactured parts. Variation in mechanical properties with layer thickness will also affect manufactured parts. Originality/value Tailorable irreversible thermal strain of this magnitude has not been previously reported for additively manufactured parts. This strain occurs in parts made with both high-end and consumer grade fused deposition modeling machines. Additionally, the impact of layer thickness on tensile and flexural properties of additively manufactured parts has received limited attention in the literature.

scholarly journals Effect of Extrusion Temperature on the Physico-Mechanical Properties of Unidirectional Wood Fiber-Reinforced Polylactic Acid Composite (WFRPC) Components Using Fused Deposition Modeling

Polymers ◽  
2018 ◽  
Vol 10 (9) ◽  
pp. 976 ◽  
Author(s):  
Teng-Chun Yang
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Fused Deposition Modeling ◽  
Wood Fiber ◽  
Color Difference ◽  
Extrusion Temperature ◽  
Fiber Reinforced ◽  
Substantial Impact ◽  
Fused Deposition ◽  
Deposition Modeling

Wood fiber-reinforced polylactic acid (PLA) composites (WFRPCs) were used as a filament to manufacture the unidirectional WFRPC components by means of fused deposition modeling (FDM). The physico-mechanical properties of the WFRPC components printed at different extrusion temperatures (200, 210, 220, and 230 °C) were determined. The results revealed that most of the physical properties (moisture content, surface roughness, water absorption rate, and thickness swelling rate) of the printed WFRPC component were not significantly influenced by extrusion temperature, while its density and color difference increased as the extrusion temperature increased. Additionally, the tensile and flexural properties of the FDM-printed WFRPC component decreased when the extrusion temperature was more than 200 °C, whereas the compressive strength and internal bond strength increased by 15.1% and 24.3%, respectively, when the extrusion temperature was increased from 200 to 230 °C. Furthermore, scanning electronic microscopy (SEM) demonstrated that the fracture surface of the tensile component printed at a higher extrusion temperature exhibited a better compatibility at fiber/PLA interfaces and good adhesion between the extruded filament segments. These results indicate that the FDM printing process using different extrusion temperatures has a substantial impact on the surface color, density, and mechanical properties of the printed WFRPC component.

Sign in / Sign up

Export Citation Format

Share Document