An overview on joining/welding as post-processing technique to circumvent the build volume limitation of an FDM-3D printer

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Vivek Kumar Tiwary ◽  
Arunkumar P. ◽  
Vinayak R. Malik
Keyword(s):  
3D Printing ◽  
Literature Review ◽  
Adhesive Bonding ◽  
Business Leaders ◽  
Future Research ◽  
3D Printer ◽  
Content Type ◽  
Friction Stir ◽  
Fused Deposition ◽  
3D Printed

Purpose Three-dimensional (3D) printing, one of the important technological pillars of Industry 4.0, is changing the landscape of future manufacturing. However, the limited build volume of a commercially available 3D printer is one inherent constraint, which holds its acceptability by the manufacturing business leaders. This paper aims to address the issue by presenting a novel classification of the possible ways by which 3D-printed parts can be joined or welded to achieve a bigger-sized component. Design/methodology/approach A two-step literature review is performed. The first section deals with the past and present research studies related to adhesive bonding, mechanical interlocking, fastening and big area additive manufacturing of 3D printed thermoplastics. In the second section, the literature searches were focused on retrieving details related to the welding of 3D printed parts, specifically related to friction stir welding, friction (spin) welding, microwave and ultrasonic welding. Findings The key findings of this review study comprise the present up-to-date research developments, pros, cons, critical challenges and the future research directions related to each of the joining/welding techniques. After reading this study, a better understanding of how and which joining/welding technique to be applied to obtain a bigger volume 3D printed component will be acquired. Practical implications The study provides a realistic approach for the joining of 3D printed parts made by the fused deposition modeling (FDM) technique. Originality/value This is the first literature review related to joining or welding of FDM-3D printed parts helping the 3D printing fraternity and researchers, thus increasing the acceptability of low-cost FDM printers by the manufacturing business leaders.

A physical investigation of dimensional and mechanical characteristics of 3D printed nut and bolt for industrial applications

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ramesh Chand ◽  
Vishal S. Sharma ◽  
Rajeev Trehan ◽  
Munish Kumar Gupta
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
3D Printing ◽  
Surface Properties ◽  
3D Printer ◽  
Content Type ◽  
Safety Issues ◽  
Machine Failure ◽  
Sharp Edges ◽  
3D Printed

Purpose A nut bolt joint is a primary device that connects mechanical components. The vibrations cause bolted joints to self-loosen. Created by motors and engines, leading to machine failure, and there may be severe safety issues. All the safety issues and self-loosen are directly and indirectly the functions of the accuracy and precision of the fabricated nut and bolt. Recent advancements in three-dimensional (3D) printing technologies now allow for the production of intricate components. These may be used technologies such as 3D printed bolts to create fasteners. This paper aims to investigate dimensional precision, surface properties, mechanical properties and scanning electron microscope (SEM) of the component fabricated using a multi-jet 3D printer. Design/methodology/approach Multi-jet-based 3D printed nut-bolt is evaluated in this paper. More specifically, liquid polymer-based nut-bolt is fabricated in sections 1, 2 and 3 of the base plate. Five nuts and bolts are fabricated in these three sections. Findings Dimensional inquiry (bolt dimension, general dimensions’ density and surface roughness) and mechanical testing (shear strength of nut and bolt) were carried out throughout the study. According to the ISO 2768 requirements for the General Tolerances Grade, the nut and bolt’s dimensional examination (variation in bolt dimension, general dimensions) is within the tolerance grades. As a result, the multi-jet 3D printing (MJP)-based 3D printer described above may be used for commercial production. In terms of mechanical qualities, when the component placement moves from Sections 1 to 3, the density of the manufactured part decreases by 0.292% (percent) and the shear strength of the nut and bolt decreases by 30%. According to the SEM examination, the density of the River markings, sharp edges, holes and sharp edges increased from Sections 1 to 3, which supports the findings mentioned above. Originality/value Hence, this work enlightens the aspects causing time lag during the 3D printing in MJP. It causes variation in the dimensional deviation, surface properties and mechanical properties of the fabricated part, which needs to be explored.

Experimental investigations into abrasive flow machining (AFM) of 3D printed ABS and PLA parts

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Nitin Dixit ◽  
Varun Sharma ◽  
Pradeep Kumar
Keyword(s):  
Surface Roughness ◽  
Biomedical Applications ◽  
Fused Deposition Modeling ◽  
Experimental Investigations ◽  
Future Research ◽  
Content Type ◽  
Abrasive Flow Machining ◽  
Fused Deposition ◽  
Cylindrical Parts ◽  
3D Printed

Purpose The surface roughness of additively manufactured parts is usually found to be high. This limits their use in industrial and biomedical applications. Therefore, these parts required post-processing to improve their surface quality. The purpose of this study is to finish three-dimensional (3D) printed acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA) parts using abrasive flow machining (AFM). Design/methodology/approach A hydrogel-based abrasive media has been developed to finish 3D printed parts. The developed abrasive media has been characterized for its rheology and thermal stability using sweep tests, thermogravimetric analysis (TGA) and differential thermal analysis (DTA). The ABS and PLA cylindrical parts have been prepared using fused deposition modeling (FDM) and finished using AFM. The experiments were designed using Taguchi (L9 OA) method. The effect of process parameters such as extrusion pressure (EP), layer thickness (LT) and abrasive concentration (AC) was investigated on the amount of material removed (MR) and percentage improvement in surface roughness (%ΔRa). Findings The developed abrasive media was found to be effective for finishing FDM printed parts using AFM. The microscope images of unfinished and finished showed a significant improvement in surface topography of additively manufactures parts after AFM. The results reveal that AC is the most significant parameter during the finishing of ABS parts. However, EP and AC are the most significant parameters for MR and %ΔRa, respectively, during the finishing of PLA parts. Practical implications The FDM technology has applications in the biomedical, electronics, aeronautics and defense sectors. PLA has good biodegradable and biocompatible properties, so widely used in biomedical applications. The ventilator splitters fabricated using FDM have a profile similar to the shape used in the present study. Research limitations/implications The present study is focused on finishing FDM printed cylindrical parts using AFM. Future research may be done on the AFM of complex shapes and freeform surfaces printed using different additive manufacturing (AM) techniques. Originality/value An abrasive media consists of xanthan gum, locust bean gum and fumed silica has been developed and characterized. An experimental study has been performed by combining printing parameters of FDM and finishing parameters of AFM. A comparative analysis in MR and %ΔRa has been reported between 3D printed ABS and PLA parts.

Use of polymer concrete for large-scale 3D printing

2021 ◽  
Vol 27 (3) ◽  
pp. 465-474
Author(s):  
Martin Krčma ◽  
David Škaroupka ◽  
Petr Vosynek ◽  
Tomáš Zikmund ◽  
Jozef Kaiser ◽  
...  
Keyword(s):  
3D Printing ◽  
Large Scale ◽  
Mechanical Performance ◽  
Construction Material ◽  
Polymer Concrete ◽  
Fused Deposition Modelling ◽  
Cast State ◽  
Content Type ◽  
Fused Deposition ◽  
3D Printed

Purpose This paper aims to focus on the evaluation of a polymer concrete as a three-dimensional (3D) printing material. An associated company has developed plastic concrete made from reused unrecyclable plastic waste. Its intended use is as a construction material. Design/methodology/approach The concrete mix, called PolyBet, composed of polypropylene and glass sand, is printed by the fused deposition modelling process. The process of material and parameter selection is described. The mechanical properties of the filled material were compared to its cast state. Samples were made from castings and two different orientations of 3D-printed parts. Three-point flex tests were carried out, and the area of the break was examined. Computed tomography of the samples was carried out. Findings The influence of the 3D printing process on the material was evaluated. The mechanical performance of the longitudinal samples was close to the cast state. There was a difference in the failure mode between the states, with cast parts exhibiting a tougher behaviour, with fractures propagating in a stair-like manner. The 3D-printed samples exhibited high degrees of porosity. Originality/value The results suggest that the novel material is a good fit for 3D printing, with little to no degradation caused by the process. Layer adhesion was shown to be excellent, with negligible effect on the finished part for the longitudinal orientation. That means, if large-scale testing of buildability is successful, the material is a good fit for additive manufacturing of building components and other large-scale structures.

scholarly journals Three-dimensional Printing Versus Conventional Machining in the Creation of a Meatal Urethral Dilator: a Cost and Mechanical Strength Analysis

2020 ◽  
Author(s):  
Michael Yue-Cheng Chen ◽  
Jacob Skewes ◽  
Ryan Daley ◽  
Maria Ann Woodruff ◽  
Nicholas John Rukin
Keyword(s):  
3D Printing ◽  
Three Dimensional ◽  
Patient Specific ◽  
Strength Analysis ◽  
Fused Deposition Modelling ◽  
3D Printer ◽  
Current Time ◽  
Fused Deposition ◽  
3D Printed ◽  
Conventional Machining

Abstract BackgroundThree-dimensional (3D) printing is a promising technology but the limitations are often poorly understood. We compare different 3D printingmethods with conventional machining techniques in manufacturing meatal urethral dilators which were recently removed from the Australian market. MethodsA prototype dilator was 3D printed vertically orientated on a low cost fused deposition modelling (FDM) 3D printer in polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS). It was also 3D printed horizontally orientated in ABS on a high-end FDM 3D printer with soluble support material, as well as on a SLS 3D printer in medical nylon. The dilator was also machined in stainless steel using a lathe. All dilators were tested mechanically in a custom rig by hanging calibrated weights from the handle until the dilator snapped. ResultsThe horizontally printed ABS dilator experienced failure at a greater load than the vertically printed PLA and ABS dilators respectively (503g vs 283g vs 163g, p < 0.001). The SLS nylon dilator and machined steel dilator did not fail. The steel dilator is most expensive with a quantity of five at 98 USD each, but this decreases to 30 USD each for a quantity of 1000. In contrast, the cost for the SLS dilator is 33 USD each for five and 27 USD each for 1000. ConclusionsAt the current time 3D printing is not a replacement for conventional manufacturing. 3D printing is best used for patient-specific parts, prototyping or manufacturing complex parts that have additional functionality that cannot otherwise beachieved.

scholarly journals COVID-19 and a novel initiative to improve safety by 3D printing personal protective equipment parts from computed tomography

2020 ◽  
Author(s):  
John Cote ◽  
John Haggstrom ◽  
Ranuga Vivkanandan ◽  
Kristin Ann Coté ◽  
Daniel Real ◽  
...  
Keyword(s):  
Computed Tomography ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
Future Research ◽  
Short Supply ◽  
Fused Deposition ◽  
Electronic Caliper ◽  
3D Printed ◽  
Original Part ◽  
Improved Accuracy

Abstract Background Powered air-purifying respirators are in short supply and can break down with extended use. Replacement parts can become hard to acquire. The aim of this study was to create an innovative quality improvement proof of concept using rapid prototyping. Methods Here we report three cases of 3D printed powered air-purifying respirator parts. 3D printing was performed on all parts using fused deposition modeling with standard polylactic acid, in the same way that presurgical models would be created. Measurements using an electronic caliper as well as CT scans were used to compare an original part to its corresponding 3D printed parts for accuracy. Results Electronic caliper and computed tomography measurements both showed accuracy consistant with current published norms. Conclusions Ultimately, there will be questions surrounding intellectual property, effectiveness and potential long-term safety for these types of 3D printed parts. Future research should look into the addition of specific nanoparticles from the position of cost, efficacy, safety and improved accuracy.

Impact of 3D-printing structure on the tribological properties of polymers

2020 ◽  
Vol 72 (6) ◽  
pp. 811-818 ◽  
Author(s):  
Muammel M. Hanon ◽  
Róbert Marczis ◽  
László Zsidai
Keyword(s):  
3D Printing ◽  
Tribological Properties ◽  
Future Research ◽  
Fused Deposition Modelling ◽  
Wear Depth ◽  
Printing Process ◽  
Content Type ◽  
Fused Deposition ◽  
Polylactide Acid ◽  
The Impact

Purpose The purpose of this paper is to examine the impact of three-dimensional (3D)-printing process settings (particularly print orientation) on the tribological properties of different polymers. Design/methodology/approach In this study, fused deposition modelling 3D-printing technology was used for fabricating the specimens. To evaluate the influence of print orientation, the test pieces were manufactured horizontally (X) and vertically (Z). The tribological properties of various printed polymers, which are polylactide acid, high tensile/high temperature-polylactide acid and polyethylene terephthalate-glycol have been studied. The tribological tests have been carried out under reciprocating sliding and dry condition. Findings The results show that the presence of various orientations during the 3D-printing process makes a difference in the coefficient of friction and the wear depth values. Findings suggest that printing structure in the horizontal orientation (X) assists in reducing friction and wear. Originality/value To date, there has been very limited research on the tribology of objects produced by 3D printing. This work was made as an attempt to pave the way for future research on the science of tribology of 3D-printed polymers.

Organizational adoption of 3D printing technology: a semisystematic literature review

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Desiree Valeria Ukobitz
Keyword(s):  
Decision Making ◽  
3D Printing ◽  
Literature Review ◽  
Strategic Decision ◽  
Future Research ◽  
Managerial Decision ◽  
Organizational Adoption ◽  
Content Type ◽  
Theoretical Concepts ◽  
The Impact

PurposeThree-dimensional (3D) printing (3DP) offers a promising value proposition across multiple manufacturing industries. Despite the variety of production benefits the technology entails, its rate of adoption is still low compared to industry forecasts. In face of this challenge, industry as well as academia requires more information and guidance. This review aims to examine the characteristics of the existing body of research on the organizational adoption of 3DP as well as its underlying theoretical concepts. The most common criteria driving adoption will be derived, such as to facilitate the managerial decision-making process. Pathways for future research will be presented.Design/methodology/approachThis study underlies a bibliometric literature review and additionally applies content analysis to systematically investigate the existing body of research and group decision criteria along the four major pillars of strategic decision-making.FindingsThe contributions of this paper are threefold. First, the bibliometric analysis reveals interesting aspects of the existing body of research. The most prominent characteristics of the contemporary literature are reflected along descriptive indicators, such as industry, method, model, origin, research outlet or adoption drivers, thus granting relevant insights into academia and practice. Second, the most notable adoption models are carefully analyzed on their inherent attributes and their application fit for the context of organizational 3DP adoption. Findings, for instance, revealed the dominance of diffusion of innovation (DOI) across the existing body of research and divulge that this construct is generally applied in combination with user-centered decision frameworks to yield more precise results. Third, an ample range of opportunities for future research are detected and thoroughly explained. Among others, the authors identified a clear lack of information on the impact environmental variables and contingency factors exerted on the organizational adoption of 3DP. Guidance in relation to the sourcing of industry data, usage of adoption frameworks and avenues for future scientific projects is supplied.Originality/valueThis study represents the first semi-systematic literature review on the organizational adoption of 3DP. Thus, it not only offers a valuable evaluation guide for potential adopters but also determines a future research agenda.

FDM 3D printing method utility assessment in small RC aircraft design

2019 ◽  
Vol 91 (6) ◽  
pp. 865-872 ◽  
Author(s):  
Igor Skawiński ◽  
Tomasz Goetzendorf-Grabowski
Keyword(s):  
3D Printing ◽  
Aircraft Design ◽  
Cost Effective ◽  
Fused Deposition Modelling ◽  
Thin Wall ◽  
Good Reliability ◽  
Content Type ◽  
Fused Deposition ◽  
Wall Structures ◽  
3D Printed

Purpose The purpose of this paper is to investigate the possibility of manufacturing fused deposition modelling (FDM) 3D printed structures such as wings or fuselages for small remote control (RC) air craft and mini unmaned aerial vehicles (UAVs). Design/methodology/approach Material tests, design assumptions and calculations were verified by designing and manufacturing a small radio-controlled motor-glider using as many printed parts as possible and performing test flights. Findings It is possible to create an aircraft with good flight characteristics using FDM 3D printed parts. Current level of technology allows for reasonably fast manufacturing of 3D printed aircraft with good reliability and high success ratio of prints; however, only some of the materials are suitable for printing thin wall structures such as wings. Practical implications The paper proves that apart from currently popular small RC aircraft structural materials such as composites, wood and foam, there is also printed plastic. Moreover, 3D printing is highly competitive in some aspects such as first unit production time or production cost. Originality/value The presented manufacturing technique can be useful for quick and cost-effective creating scale prototypes of the aircraft for performing test flights.

Rapid prototyping eddy current sensors using 3D printing

2018 ◽  
Vol 24 (1) ◽  
pp. 106-113 ◽  
Author(s):  
Bo Li ◽  
Lifan Meng ◽  
Hongyu Wang ◽  
Jing Li ◽  
Chunmei Liu
Keyword(s):  
3D Printing ◽  
Rapid Prototyping ◽  
Eddy Current ◽  
Fused Deposition Modeling ◽  
Current Sensor ◽  
Content Type ◽  
Fused Deposition ◽  
Eddy Current Sensor ◽  
3D Printed ◽  
Current Sensors

Purpose The purpose of this paper is to investigate the process of rapid prototyping eddy current sensors using 3D printing technology. Making full use of the advantages of 3D printing, the authors study on a new method for fabrication of an eddy current sensor. Design/methodology/approach In this paper, the authors establish a 3D model using SolidWorks. And the eddy current sensor is printed by the fused deposition modeling method. Findings Measurement results show that the 3D printing eddy current sensor has a wider linear measurement range and better linearity than the traditional manufacturing sensor. Compared to traditional eddy current sensor fabrication method, this 3D printed sensor can be fabricated at a lower cost, and the fabrication process is more convenient and faster. Practical implications This demonstrated 3D printing process can be applied to the 3D printing of sensors of more sophisticated structures that are difficult to fabricate using conventional techniques. Originality/value In this work, the process of rapid prototyping eddy current sensors using 3D printing is presented. Sensors fabricated with the 3D printing possess lots of merits than traditional manufactures. 3D printed sensors can be customized according to the configuration of the overall system, thus reducing the demand of sensor's rigid mounting interfaces. The 3D printing also reduce design costs as well as shortens the development cycle. This allows for quick translation of a design from concept to a useful device.

Preparation of cation exchange filament for 3D membrane print

2020 ◽  
Vol 26 (8) ◽  
pp. 1435-1445
Author(s):  
Lucie Zarybnicka ◽  
Eliska Stranska
Keyword(s):  
Thermal Properties ◽  
3D Printing ◽  
Cation Exchange ◽  
Dry Matter ◽  
Cation Exchanger ◽  
Flow Index ◽  
Content Type ◽  
3D Print ◽  
Fused Deposition ◽  
3D Printed

Purpose This paper aims to focus on the preparation of a cation exchange filament for three-dimensional (3D) fused deposition modeling (FDM). The polymeric binder was mixed with the selected conventional cation exchange resin and a filament was prepared using a mini extruder. Filaments were tested by mechanical properties, chemical properties, quality and melt flow index. Samples were prepared from granulate using a press, which were tested for electrochemical properties, thermal properties. The best result of ion exchange capacity (IEC) up to 3.0 meq/g of the dry matter was achieved with filament fill 65%. Permselectivity results above 90% were determined for 55%–65% filling of the cation exchanger. The results obtained are a promising step for the preparation of 3D printed cation exchange membranes (CEMs) with a defined structure. Design/methodology/approach The prepared granulates and filaments were evaluated using mechanical, rheological and thermal properties. Findings The prepared cation exchange filament can be used for the 3D printing process. The best result of IEC up to 3.0 meq/g of the dry matter was achieved with filament fill 65%. Permselectivity results above 90% were determined for 55%–65% filling of the cation exchanger, and area resistances 3.0 Ocm2 and specific resistances around 57 Ocm for 65% filling of the cation exchanger. The results obtained are a promising step for the preparation of 3D printed CEMs with a defined structure. Originality/value The prepared cation exchange filament. Using new materials for 3D print of cation exchange membrane. Production without waste. The possibility of producing 3D membranes with a precisely defined structure. Processing prepared filaments using a cheap FDM 3D printing method. New direction of membrane formation.

Sign in / Sign up

Export Citation Format

Share Document