Removal of Cr(VI) from aqueous solutions by using activated carbon supported iron catalysts as efficient adsorbents

2018 ◽  
Vol 15 (1) ◽  
pp. 3-13 ◽  
Author(s):  
Karima Derdour ◽  
Chafia Bouchelta ◽  
Amina Khorief Naser-Eddine ◽  
Mohamed Salah Medjram ◽  
Pierre Magri
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Adsorption Isotherms ◽  
Walnut Shell ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Solution Ph ◽  
Content Type ◽  
Order Kinetic Model ◽  
Fe Catalysts

Purpose The purpose of this paper is to focus on the removal of hexavalent chromium [Cr(VI)] from wastewater by using activated carbon-supported Fe catalysts derived from walnut shell prepared using a wetness impregnation process. The different conditions of preparation such as impregnation rate and calcination conditions (temperature and time) were optimized to determine their effects on the catalyst’s characteristics. Design/methodology/approach The catalyst samples were characterized using thermogravimetric analysis, scanning electron microscopy and Fourier transform infrared spectroscopy. The adsorption of Cr(VI) by using using activated carbon supported Fe catalysts derived from walnut shell as an adsorbent and catalyst was investigated under different adsorption conditions. The parameters studied were contact time, adsorbent dose, solution pH and initial concentrations. Findings Results showed that higher adsorption capacity and rapid kinetics were obtained when the activated walnut shell was impregnated with Fe at 5 per cent and calcined under N2 flow at 400°C for 2 h. The adsorption isotherms data were analyzed with Langmuir and Freundlich models. The better fit is obtained with the Langmuir model with a maximum adsorption capacity of 29.67 mg/g for Cr(VI) on Fe5-AWS at pH 2.0. Originality/value A comparison of two kinetic models shows that the adsorption isotherms system is better described by the pseudo-first-order kinetic model.

scholarly journals Modified Vermiculite as Adsorbent of Hexavalent Chromium in Aqueous Solution

Minerals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 749
Author(s):  
Celia Marcos ◽  
Valeria Medoro ◽  
Alaa Adawy
Keyword(s):  
Adsorption Capacity ◽  
Adsorption Energy ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Ion Chemistry ◽  
Solution Ph ◽  
Cooperative Process ◽  
Order Kinetic Model ◽  
Initial Adsorption ◽  
Initial Adsorption Rate

The aim of this study was to investigate the efficiency of removing Cr6+ from aqueous solutions using two exfoliated vermiculite: (1) heated abruptly at 1000 °C and (2) irradiated with microwave radiation. The effects investigated were contact time, adsorbate concentration and initial Cr6+ concentration. The adsorption with both exfoliated vermiculites was well described by the DKR isotherm, indicative of a cooperative process and with the pseudo second order kinetic model. The Kd value for the two exfoliated vermiculites was similar, 0.2 ·1010 μg/Kg. The maximum adsorption capacity of Cr6+ with thermo-exfoliated vermiculite, 2.81 mol/g, was much higher than with microwave irradiated vermiculite, 0.001 mol/g; both values were obtained with 0.5 g of vermiculite in contact with distilled water enriched with 1 ppm of Cr6+ for 24 h. Factors such as ion chemistry, the solution pH and ionic strength, influence the values of capacity, adsorption energy and initial adsorption rate values of the exfoliated vermiculite. In addition, these values depended on the exfoliation process, being the adsorption capacity highest with abrupt heating of vermiculite, while the adsorption energy and rate values showed just a slight increase with microwave irradiation. This aspect is important to select the most suitable vermiculite modification treatment to use it as an adsorbent.

scholarly journals Polymer-Functionalized Magnetic Nanoparticles: Synthesis, Characterization, and Methylene Blue Adsorption

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1312 ◽  
Author(s):  
Xinyu Zheng ◽  
Huaili Zheng ◽  
Rui Zhao ◽  
Yongjun Sun ◽  
Qiang Sun ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Magnetic Nanoparticles ◽  
Adsorption Capacity ◽  
Monomer Concentration ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Solution Ph ◽  
Functionalized Magnetic Nanoparticles ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The removal of methylene blue (MB) from wastewater has attracted global concerns. In this study, polymer-functionalized magnetic nanoparticles for MB removal, Fe3O4@SiO2-MPS-g-AA-AMPS (FSMAA), were successfully synthesized by grafting acrylic acid (AA) and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) on the surface of vinyl-modified Fe3O4@SiO2. With various characterization techniques, it was confirmed that the obtained FSMAA had a core–shell structure, a good magnetic property, and plenty of functional groups on its surface. MB adsorption experiments showed that the adsorption capacity of FSMAA was notably enhanced as the grafted monomer concentration and solution pH were increased. The adsorption kinetic data and isothermal data were well described by the pseudo-second-order kinetic model and the Langmuir model, respectively. The maximum adsorption capacity of FSMAA was 421.9 mg g−1 with grafted monomer concentration at 2.0 mol L−1 and solution pH at 9, much higher than those of other adsorbents stated in previous literatures. Based on XPS analysis, surface adsorption mechanism between FSMAA and MB was electrostatic interaction, hydrogen bonding, and hydrophobic interaction. Furthermore, FSMAA was effectively regenerated by acid pickling, and the remaining adsorption capacity was more than 60% after eight adsorption–regeneration cycles. All the results demonstrated the self-made FSMAA was a desirable adsorbent to remove MB from wastewater.

scholarly journals Karekterisasi, Kinetika, dan Isoterm Adsorpsi Limbah Ampas Kelapa sebagai Adsorben Ion Cu(II)

SAINTIFIK ◽  
2020 ◽  
Vol 6 (2) ◽  
pp. 104-115
Author(s):  
Agusriyadin Agusriyadin
Keyword(s):  
Adsorption Capacity ◽  
Ph Effect ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Optimum Conditions ◽  
Langmuir Adsorption ◽  
Adsorbent Surface ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Penelitian ini bertujuan untuk menguji kemampuan AK dan AKPM dalam mengadsorpsi ion Cu (II), pengaruh parameter adsorpsi dan mekanisme adsorpsi. AK dan AKP Madsorben dibuat dari residu ampas kelapa. Adsorben dikarakterisasi dengan FTIR, SEM dan EDS. Pengaruh parameter adsorpsi seperti pH awal, dosis adsorben, waktu kontak dan konsentrasi ion Cu (II) awal diperiksa untuk menentukan kondisi optimum serapan tembaga (II). Ion Cu (II) yang teradsorpsi diukur berdasarkan pada konsentrasi Ion Cu (II) sebelum dan sesudah adsorpsi menggunakan metode AAS. Hasil karakterisasi menunjukkan bahwa struktur pori dan gugus fungsi tersedia pada permukaan adsorben. Menurut percobaan efek pH, kapasitas adsorpsi maksimum dicapai pada pH 7. Waktu kontak optimal dan konsentrasi tembaga awal (II) ditemukan masing-masing pada 120 menit dan 100 mg L-1. Data eksperimental sesuai dengan model kinetik orde dua orde dua, dan Langmuir isoterm adsorpsi yang diperoleh paling sesuai dengan data adsorpsi. Kapasitas adsorpsi maksimum adsorben ditemukan menjadi 4,73 dan 6,46 mg g-1 pada kondisi optimal. The results of characterization showed that the pore structure and the functional groups were available on adsorbent surface. According to the pH effect experiments, the maximum adsorption capacity was achieved at pH 7. Optimum contact time and initial copper(II) concentration were found at 120 min and 100 mg L-1, respectively. The experimental data were comply with the pseudo-second-order kinetic model, and Langmuir adsorption isotherm obtained best fitted the adsorption data. The maximum adsorption capacity of the adsorbents was found to be 4.73 and 6.46 mg g-1 at optimum conditions.

scholarly journals Preparation of bio-absorbents by modifying licorice residue via chemical methods and removal of copper ions from wastewater

2021 ◽  
Author(s):  
Xiaochun Yin ◽  
Nadi Zhang ◽  
Meixia Du ◽  
Hai Zhu ◽  
Ting Ke
Keyword(s):  
Adsorption Capacity ◽  
Copper Ions ◽  
Order Kinetic ◽  
Solution Ph ◽  
Chemical Methods ◽  
Simple Strategy ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Surface Active ◽  
Adsorption Desorption

Abstract In this paper, a series of bio-adsorbents (LR-NaOH, LR-Na2CO3 and LR-CA) were successfully prepared by modifying Licorice Residue with NaOH, Na2CO3 and citric acid, which were used as the adsorbents to remove Cu2+ from wastewater. The morphology and structure of bio-adsorbents were characterized by Fourier Transform Infrared, SEM, TG and XRD. Using static adsorption experiments, the effects of the adsorbent dosage, the solution pH, the adsorption time, and the initial Cu2+ concentration on the adsorption performance of the adsorbents were investigated. The results showed that the adsorption process of Cu2+ by the bio-adsorbents can be described by pseudo-second order kinetic model and the Langmuir model. The surface structure of the LR-NaOH, LR-Na2CO3 and LR-CA changed obviously, and the surface-active groups increased. The adsorption capacity of raw LR was 21.56 mg/g, LR-NaOH, LR- Na2CO3 significantly enhanced this value up to 43.65 mg/g, 43.55 mg/g, respectively. After four adsorption-desorption processes, the adsorption capacity of LR-NaOH also maintained about 73%. Therefore, LR-NaOH would be a promising adsorbent for removing Cu2+ from wastewater, and the simple strategy towards preparation of adsorbent from the waste residue can be as a potential approach using in the water treatment.

Preparation of Graphene Oxide Modified Rice Husk for Cr(VI) Removal

2019 ◽  
Vol 19 (11) ◽  
pp. 7035-7043 ◽  
Author(s):  
Tong Ouyang ◽  
Jidan Tang ◽  
Fang Liu ◽  
Chang-Tang Chang
Keyword(s):  
Graphene Oxide ◽  
Adsorption Capacity ◽  
Rice Husk ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Adsorption Sites ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Alkaline Conditions ◽  
Rice Husk Biochar

The objective of this paper is to study the removal of Cr(VI) in aqueous solution by using a new graphene oxide-coated rice husk biochar composite (GO-RHB). GO-RHB is a synthetic material having a porous structure with lots of oxygen-containing functional groups and a large surface area that provide effective adsorption sites. Experiments showed that GO-RHB had higher adsorption capacity under acidic than under alkaline conditions. At pH of 2, GO-RHB has the maximum adsorption capacity(48.8 mg g−1). Equilibrium data obtained by fitting with the Langmuir and Freundlich models indicate that the reaction process was monolayer adsorption. The adsorption of Cr(VI) followed the pseudo-second-order kinetic model that illustrates chemical adsorption. Intraparticlediffusion studies further revealed that film diffusion was taking place. Moreover, the results of thermodynamics showed that the adsorption process was endothermic and spontaneous in nature. The removal mechanism of Cr(VI) was also explained in detail. The prepared adsorbent is highly efficient and might be useful than many other conventional adsorbent used for the removal of Cr(VI) from wastewater.

scholarly journals Effective Removal of Pb(II) Ions by Electrospun PAN/Sago Lignin-Based Activated Carbon Nanofibers

Molecules ◽  
2020 ◽  
Vol 25 (13) ◽  
pp. 3081 ◽  
Author(s):  
Nurul Aida Nordin ◽  
Norizah Abdul Rahman ◽  
Abdul Halim Abdullah
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Carbon Nanofibers ◽  
Langmuir Isotherm ◽  
Human Life ◽  
Order Kinetic ◽  
Solution Ph ◽  
Adsorption Sites ◽  
Activated Carbon Nanofibers ◽  
Adsorption Technology

Heavy metal pollution, such as lead, can cause contamination of water resources and harm human life. Many techniques have been explored and utilized to overcome this problem, with adsorption technology being the most common strategies for water treatment. In this study, carbon nanofibers, polyacrylonitrile (PAN)/sago lignin (SL) carbon nanofibers (PAN/SL CNF) and PAN/SL activated carbon nanofibers (PAN/SL ACNF), with a diameter approximately 300 nm, were produced by electrospinning blends of polyacrylonitrile and sago lignin followed by thermal and acid treatments and used as adsorbents for the removal of Pb(II) ions from aqueous solutions. The incorporation of biodegradable and renewable SL in PAN/SL blends fibers produces the CNF with a smaller diameter than PAN only but preserves the structure of CNF. The adsorption of Pb(II) ions on PAN/SL ACNF was three times higher than that of PAN/SL CNF. The enhanced removal was due to the nitric acid treatment that resulted in the formation of surface oxygenated functional groups that promoted the Pb(II) ions adsorption. The best-suited adsorption conditions that gave the highest percentage removal of 67%, with an adsorption capacity of 524 mg/g, were 40 mg of adsorbent dosage, 125 ppm of Pb(II) solution, pH 5, and a contact time of 240 min. The adsorption data fitted the Langmuir isotherm and the pseudo-second-order kinetic models, indicating that the adsorption is a monolayer, and is governed by the availability of the adsorption sites. With the adsorption capacity of 588 mg/g, determined via the Langmuir isotherm model, the study demonstrated the potential of PAN/SL ACNFs as the adsorbent for the removal of Pb(II) ions from aqueous solution.

Application of Carbonaceous Materials to Phenol Removal from Aqueous Solution by Adsorption

2012 ◽  
Vol 164 ◽  
pp. 297-301 ◽  
Author(s):  
Wei Fang Dong ◽  
Li Hua Zang ◽  
Qing Chao Gong ◽  
Cun Cun Chen ◽  
Cai Hong Zheng ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Petroleum Coke ◽  
Granular Activated Carbon ◽  
Powdered Activated Carbon ◽  
Maximum Adsorption Capacity ◽  
Phenol Removal ◽  
Carbonaceous Materials ◽  
Solution Ph ◽  
Equilibrium Studies

Low cost carbonaceous materials were evaluated for their ability to remove phenol from wastewater. The effects of adsorbents dosage, contact time and maximum adsorption capacity were investigated for granular activated carbon, powdered activated carbon, petroleum coke and multi-walled carbon nanotube (MWNT). Equilibrium studies were conducted in 50mg/L initial phenol concentration, solution pH of 5 and at temperature of 23°C. The results showed the adsorption process was fast and it reached equilibrium in 3 h. Petroleum coke and MWNT had poor adsorption which could reach the removal efficiency of phenol with 43.18% and 36.64% respectively. The granular activated carbon possessed good adsorption ability to phenol with 96.40% at the optimum dosage 5g and optimum time 90min.The powdered activated carbon was an effective adsorbent with a maximum adsorption capacity of 42.32 mg/g.

Adsorption of cadmium(II) from aqueous solution onto activated carbon

1997 ◽  
Vol 35 (7) ◽  
pp. 205-211 ◽  
Author(s):  
R. Leyva-Ramos ◽  
J. R. Rangel-Mendez ◽  
J. Mendoza-Barron ◽  
L. Fuentes-Rubio ◽  
R. M. Guerrero-Coronado
Keyword(s):  
Activated Carbon ◽  
Adsorption Isotherm ◽  
Adsorption Capacity ◽  
Freundlich Isotherm ◽  
Carbon Surface ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Ph Values ◽  
Average Percent Deviation ◽  
Initial Ph

The adsorption isotherm of cadmium on activated carbon was measured in a batch adsorber. Effects of temperature and solution pH on the adsorption isotherm were investigated by determining the adsorption isotherm at temperatures of 10, 25, and 40°C and at initial pH values from 2 to 8. Langmuir isotherm better fitted the experimental data since the average percent deviation was lower than with the Freundlich isotherm It was noticed that the amount of Cd2+ adsorbed was reduced about 3 times by increasing the temperature from 10 to 40°C. It was found that Cd2+ was not adsorbed on activated carbon at pH of 2 or lower and that Cd2+ was precipitated out as Cd(OH)2 at pH values above 9. Maximum adsorption capacity was observed at pH of 8 and the adsorption capacity was decreased about 12 times by reducing the initial pH from 8 to 3. According to the cadmium speciation diagram the predominant species below pH of 8 is Cd2+. Thus, cadmium was adsorbed on the activated carbon surface as Cd2+. It was concluded that the adsorption capacity is a strong function of pH and temperature.

scholarly journals Adsorption of Ni2+ from aqueous solution by magnetic Fe@graphite nano-composite

2016 ◽  
Vol 18 (4) ◽  
pp. 96-103 ◽  
Author(s):  
Wojciech Konicki ◽  
Rafał Pelka ◽  
Walerian Arabczyk
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Diffraction Method ◽  
Chemical Vapor ◽  
Bet Surface Area ◽  
Order Kinetic ◽  
Solution Ph ◽  
Transmission Electron ◽  
Order Kinetic Model ◽  
Nanocrystalline Iron

Abstract The removal of Ni2+ from aqueous solution by iron nanoparticles encapsulated by graphitic layers (Fe@G) was investigated. Nanoparticles Fe@G were prepared by chemical vapor deposition CVD process using methane as a carbon source and nanocrystalline iron. The properties of Fe@G were characterized by X-ray Diffraction method (XRD), High-Resolution Transmission Electron Microscopy (HRTEM), Fourier Transform-Infrared Spectroscopy (FTIR), BET surface area and zeta potential measurements. The effects of initial Ni2+ concentration (1–20 mg L−1), pH (4–11) and temperature (20–60°C) on adsorption capacity were studied. The adsorption capacity at equilibrium increased from 2.96 to 8.78 mg g−1, with the increase in the initial concentration of Ni2+ from 1 to 20 mg L−1 at pH 7.0 and 20oC. The experimental results indicated that the maximum Ni2+ removal could be attained at a solution pH of 8.2 and the adsorption capacity obtained was 9.33 mg g−1. The experimental data fitted well with the Langmuir model with a monolayer adsorption capacity of 9.20 mg g−1. The adsorption kinetics was found to follow pseudo-second-order kinetic model. Thermodynamics parameters, ΔHO, ΔGO and ΔSO, were calculated, indicating that the adsorption of Ni2+ onto Fe@G was spontaneous and endothermic in nature.

Equilibrium and Kinetic Studies of Benzene and Toluene Adsorption onto Microwave Irradiated-Coconut Shell Activated Carbon

2014 ◽  
Vol 1043 ◽  
pp. 219-223 ◽  
Author(s):  
Noor Shawal Nasri ◽  
Jibril Mohammed ◽  
Muhammad Abbas Ahmad Zaini ◽  
Usman Dadum Hamza ◽  
Husna Mohd. Zain ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Kinetic Studies ◽  
Coconut Shell ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Volatile Organic ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Coconut Shell Activated Carbon

Concern about environmental protection has increased over the years and the presence of volatile organic compounds (VOCs) in water poses a threat to the environment. In this study, coconut shell activated carbon (PHAC) was produced by potassium hydroxide activation via microwave for benzene and toluene removal. Equilibrium data were fitted to Langmuir, Freundlich and Tempkin isotherms with all the models having R2 > 0.94. The equilibrium data were best fitted by Langmuir isotherm, with maximum adsorption capacity of 212 and 238mg/g for benzene and toluene, respectively. The equilibrium parameter (RL) falls between 0 and 1 confirming the favourability of the Langmuir model. Pseudo-second-order kinetic model best fitted the kinetic data. The PHAC produced can be used to remediate water polluted by VOCs.

Sign in / Sign up

Export Citation Format

Share Document