Equilibrium and Kinetic Studies of Benzene and Toluene Adsorption onto Microwave Irradiated-Coconut Shell Activated Carbon

2014 ◽  
Vol 1043 ◽  
pp. 219-223 ◽  
Author(s):  
Noor Shawal Nasri ◽  
Jibril Mohammed ◽  
Muhammad Abbas Ahmad Zaini ◽  
Usman Dadum Hamza ◽  
Husna Mohd. Zain ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Kinetic Studies ◽  
Coconut Shell ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Volatile Organic ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Coconut Shell Activated Carbon

Concern about environmental protection has increased over the years and the presence of volatile organic compounds (VOCs) in water poses a threat to the environment. In this study, coconut shell activated carbon (PHAC) was produced by potassium hydroxide activation via microwave for benzene and toluene removal. Equilibrium data were fitted to Langmuir, Freundlich and Tempkin isotherms with all the models having R2 > 0.94. The equilibrium data were best fitted by Langmuir isotherm, with maximum adsorption capacity of 212 and 238mg/g for benzene and toluene, respectively. The equilibrium parameter (RL) falls between 0 and 1 confirming the favourability of the Langmuir model. Pseudo-second-order kinetic model best fitted the kinetic data. The PHAC produced can be used to remediate water polluted by VOCs.

Studies of Chromium Removal from Tannery Effluents by Dead Streptomyces Rimosus

2008 ◽  
Vol 3 (1) ◽  
Author(s):  
Mohamed Nasser Sahmoune ◽  
Krim Louhab ◽  
Aissa Boukhiar
Keyword(s):  
Fractional Power ◽  
Kinetic Studies ◽  
Second Order ◽  
Order Kinetic ◽  
Streptomyces Rimosus ◽  
Tannery Effluents ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Ph Range

Dead streptomyces rimosus was found to be an effective biosorbent for the removal of chromium from industrial tanning effluents. A sorption level of 65 mg/g was observed at pH 4.8 while the precipitation effect augmented this value at a higher pH range. Chromium desorption increased with decreasing desorption agents pH (including HCl and H2SO4) to a maximum value of 95% at approximately zero pH. The biosorption data of trivalent chromium by streptomyces rimosus has been used for kinetic studies based on fractional power, Elovich, pseudo-first order and pseudo-second order rate expressions. The time-dependent Cr (III) biosorption data were well-described by a pseudo-second-order kinetic model. The intraparticle diffusion is not the rate-limiting step for the whole reaction. It was found that the biosorption equilibrium data fit well with the Langmuir model.

scholarly journals Adsorption of Hexavalent Chromium from Aqueous Solution Using Chemically Activated Carbon Prepared from Locally Available Waste of Bamboo (Oxytenanthera abyssinica)

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Tamirat Dula ◽  
Khalid Siraj ◽  
Shimeles Addisu Kitte
Keyword(s):  
Activated Carbon ◽  
Hexavalent Chromium ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Batch Adsorption ◽  
Koh Activation ◽  
Order Kinetic ◽  
Oxytenanthera Abyssinica ◽  
Equilibrium Data ◽  
Order Kinetic Model

This study reports on the adsorption of Hexavalent Chromium from aqueous solutions using activated carbon prepared from bamboo (Oxytenanthera abyssinica) waste by KOH activation heating in an electrical furnace at 1073 K for 3 hrs. Batch adsorption experiments were also carried out as a function of pH, contact time, initial concentration of the adsorbate, adsorbent dosage, and temperature of the solution. Kinetic studies of the data showed that the adsorption follows the pseudo-second-order kinetic model. Thermodynamic parameters showed that adsorption on the surface of BWAC was feasible, spontaneous in nature, and exothermic between temperatures of 298 and 318 K. The equilibrium data better fitted the Freundlich isotherm model for studying the adsorption behavior of Hexavalent Chromium by BWAC. IR spectrum for loaded and unloaded BWAC was obtained using FT-IR spectrophotometer. Adsorption efficiency and capacity of Hexavalent Chromium were found to be 98.28% at pH 2 and 59.23 mg/g at 300 K.

Alkaline deoxygenated graphene oxide as adsorbent for cadmium ions removal from aqueous solutions

2015 ◽  
Vol 71 (11) ◽  
pp. 1611-1619 ◽  
Author(s):  
Jun Liu ◽  
Hongyan Du ◽  
Shaowei Yuan ◽  
Wanxia He ◽  
Pengju Yan ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Aqueous Solutions ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Transmission Electron ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Ft Ir

Alkaline deoxygenated graphene oxide (aGO) was prepared through alkaline hydrothermal treatment and used as adsorbent to remove Cd(II) ions from aqueous solutions for the first time. The characterization results of transmission electron microscopy, X-ray diffraction, Raman spectroscopy, and Fourier transform infrared (FT-IR) spectra indicate that aGO was successfully synthesized. The batch adsorption experiments showed that the adsorption kinetics could be described by the pseudo-second-order kinetic model, and the isotherms equilibrium data were well fitted with the Langmuir model. The maximum adsorption capacity of Cd(II) on aGO was 156 mg/g at pH 5 and T = 293 K. The adsorption thermodynamic parameters indicated that the adsorption process was a spontaneous and endothermic reaction. The mainly adsorption mechanism speculated from FT-IR results may be attributed to the electrostatic attraction between Cd2+ and negatively charged groups (–CO−) of aGO and cation-π interaction between Cd2+ and the graphene planes. The findings of this study demonstrate the potential utility of the nanomaterial aGO as an effective adsorbent for Cd(II) removal from aqueous solutions.

scholarly journals Lead removal using Fallen Coffee Plant Leaves (FCPL) powder: Characterization, Equilibrium, Kinetics and Thermodynamic studies

2021 ◽  
Vol 309 ◽  
pp. 01077
Author(s):  
M Tukaram Bai ◽  
Ch. I. A. Raju ◽  
V Sridevi ◽  
Nalluri Chittibabu ◽  
P Venkateswarlu
Keyword(s):  
Correlation Coefficient ◽  
Kinetic Studies ◽  
Lead Removal ◽  
Order Kinetic ◽  
Plant Leaves ◽  
Coffee Plant ◽  
Freundlich Isotherms ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Biosorption of lead onto Fallen Coffee Plant leaves (FCPL) powder from an aqueous solution was studied in the present study. The characterization of FCPL powder was done by FTIR, XRD, SEM and BET. The equilibrium agitation time for lead biosorption is 60 min. The optimum pH and dosage values are 5.2 and 20 g/L respectively. In the range of variables studied, percentage biosorption is increased from 75.1 to 95.5 %. The maximum uptake capacity of 3.664 mg/g is obtained at 303 K. In the present investigation the equilibrium data was well explained by Langmuir, Redlich-Peterson with a correlation coefficient of 0.99, and followed by Temkin and Freundlich isotherms. The kinetic studies reveal that the biosorption system obeyed the pseudo second order kinetic model by considering the correlation coefficient value as 0.99. From the values of ∆S, ∆H and ∆G it is observed that the biosorption of lead onto Fallen coffee plant leaves(FCPL) powder was irreversible, endothermic and spontaneous.

scholarly journals Kinetic and Thermodynamic Study of Phenol Removal from Water Using Activated Carbon Synthesizes from Avocado Kernel Seed

2016 ◽  
Vol 54 ◽  
pp. 42-57 ◽  
Author(s):  
Kassahun Dejene ◽  
Khalid Siraj ◽  
Shimeles Addisu Kitte
Keyword(s):  
Activated Carbon ◽  
Adsorption Process ◽  
Kinetic Studies ◽  
Persea Americana ◽  
Phenol Removal ◽  
Order Kinetic ◽  
Solution Ph ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Kinetic And Thermodynamic Study

This study was aimed for removal of phenol from water using activated carbon synthesize from avocado kernel seeds by adsorption onto it. For adsorption process cleaned and washed avocado kernel seeds (Persea americana) were dried at 100°C in an oven overnight and carbonization was carried out by increasing the furnace temperature at a rate of 5 °C/min to a final temperature of 800 °C for 160 minutes. Then, the activated carbon was powdered and sieved, washed with distilled water until the solution pH reached 7.0. Optimization of activated carbon was performed through effects of solution pH, contact time; initial phenol concentration and temperature of the adsorption. The kinetic studies of the adsorption process were achieved by verifying various models and the data obtained was best fitted to pseudo-second-order kinetic model. The isotherms models were analyzed with Langmuir, Freundlich and Temkin to validate the adsorption process. It was found that Langmuir model was best fitted to the obtained result for both adsorbents.

scholarly journals Removal of Pb2+ in Wastewater via Adsorption onto an Activated Carbon Produced from Winemaking Waste

Metals ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 697 ◽  
Author(s):  
Francisco Alguacil ◽  
Lorena Alcaraz ◽  
Irene García-Díaz ◽  
Félix López
Keyword(s):  
Activated Carbon ◽  
Polluted Water ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Physico Chemical ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Chemical Factors ◽  
Pseudo Second Order ◽  
Kinetic And Thermodynamic Studies

This work describes the adsorption of Pb2+ in aqueous solution onto an activated carbon (AC) produced from winemaking waste (cluster stalks). After characterizing the AC using Fourier transform infrared spectroscopy (FTIR) and micro-Raman spectroscopy, the influence of different physico-chemical factors (stirring rate, temperature, pH, adsorbent concentration, etc.) on its capacity to adsorb Pb2+ was examined. Kinetic and thermodynamic studies showed that the adsorption of the Pb2+ follows a pseudo-second-order kinetic model and fits the Langmuir isotherm model, respectively. The maximum adsorption capacity of the AC was 58 mg/g at 288 K temperature and pH of 4. In conclusion, ACs made from waste cluster stalks could be successfully used to remove Pb2+ from polluted water.

scholarly journals Adsorption of Lead(II) Ions from Aqueous Solution onto Lignin

2009 ◽  
Vol 27 (4) ◽  
pp. 435-445 ◽  
Author(s):  
Laura Bulgariu ◽  
Dumitru Bulgariu ◽  
Theodor Malutan ◽  
Matei Macoveanu
Keyword(s):  
Aqueous Solution ◽  
Ion Concentration ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Solution Ph ◽  
Batch System ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

The adsorption of lead(II) ions from aqueous solution onto lignin was investigated in this study. Thus, the influence of the initial solution pH, the lignin dosage, the initial Pb(II) ion concentration and the contact time were investigated at room temperature (19 ± 0.5 °C) in a batch system. Adsorption equilibrium was approached within 30 min. The adsorption kinetic data could be well described by the pseudo-second-order kinetic model, while the equilibrium data were well fitted using the Langmuir isotherm model. A maximum adsorption capacity of 32.36 mg/g was observed. The results of this study indicate that lignin has the potential to become an effective and economical adsorbent for the removal of Pb(II) ions from industrial wastewaters.

Improvement of As(III) removal with diatomite overlay nanoscale zero-valent iron (nZVI-D): adsorption isotherm and adsorption kinetic studies

2016 ◽  
Vol 17 (1) ◽  
pp. 212-220 ◽  
Author(s):  
Nusavadee Pojananukij ◽  
Kitirote Wantala ◽  
Sutasinee Neramittagapong ◽  
Chitsan Lin ◽  
Duangkanok Tanangteerpong ◽  
...  
Keyword(s):  
Adsorption Isotherm ◽  
Kinetic Studies ◽  
Second Order ◽  
Zero Valent Iron ◽  
Order Kinetic ◽  
Kinetic Adsorption ◽  
Nanoscale Zero Valent Iron ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Nanoscale zero-valent iron coated on diatomite (nZVI-D) was successfully synthesized as a composite material. It is the combination of nZVI and diatomite which has been proved to be a promising material in arsenite or As(III) removal. The result showed that 25.5% of As(III) was removed using diatomite only but more than 95% of As(III) was removed using nZVI-D, at the same contact time of 60 min and pH 6. The experimental isotherm data for As(III) adsorption at different initial concentrations were analyzed using the Langmuir, Freundlich, and Dubinin–Radushkevich equations. Among these three, the equilibrium data fitted well with the Langmuir isotherm. The kinetic adsorption was also studied using the pseudo-first, second-order, and intraparticle diffusion equations. The data were well explained by the pseudo-second-order kinetic model. From the results of kinetic adsorption and the adsorption isotherm, it can be concluded that arsenite adsorption was controlled by the mass transfer and adsorption process.

scholarly journals Removal of metronidazole antibiotic from aqueous solution by ammonia-modified activated carbon: adsorption isotherm and kinetic study

2021 ◽  
Author(s):  
Ali Ahmadfazeli ◽  
Yousef Poureshgh ◽  
Yousef Rashtbari ◽  
Hamed Akbari ◽  
Peyman Pourali ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Isotherm ◽  
Contact Time ◽  
Kinetic Studies ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Activated Carbon Adsorption ◽  
Modified Activated Carbon ◽  
Initial Ph ◽  
Order Kinetic Model

Abstract This article was aimed at investigating the removal of metronidazole (MNZ) from aquatic solutions by modified activated carbon (MAC) with amine groups. The effect of various parameters on the adsorption rate such as the initial pH, adsorbent dose and initial concentration of MNZ and contact time were scrutinized. MAC was characterized by Fourier transform infrared spectroscopy and Brunauer–Emmett–Teller techniques. The obtained results illustrated that under the optimum conditions (pH = 3, contact time = 50 min, initial MNZ concentration = 5 mg/L and MAC dose = 0.5 g/L), the maximum adsorption efficiency was 95%. Furthermore, the kinetic studies indicated the applicability of the pseudo-second-order kinetic model, whereas the adsorption isotherm fitted well with the Freundlich model (0.996), and the maximum adsorption capacity was 66.22 mg/g. The SBET and the total pure volume of MAC were 706.92 m2/g and 0.532 cm3/g, respectively. Also, the regeneration tests demonstrated that MAC had good stability after five cycles (73%). It can be concluded that MAC, as an effective adsorbent, has a high ability to remove MNZ from aqueous solutions.

scholarly journals Removal of Pb(II) by Pellicle-Like Biofilm-Producing Methylobacterium hispanicum EM2 Strain from Aqueous Media

Water ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 2081 ◽  
Author(s):  
Sun-Wook Jeong ◽  
Hyo Kim ◽  
Jung Yang ◽  
Yong Choi
Keyword(s):  
Aqueous Media ◽  
Freundlich Isotherm ◽  
Infrared Analysis ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Multilayer Adsorption ◽  
Drinking Water Contamination ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

As concerns are increasing about drinking water contamination with heavy metals, we investigated the possible use of a pellicle (floating biofilm)-like biofilm-producing microorganism as a biosorbent for the treatment of Pb(II) in aqueous solutions. The bacterial pellicle-producing Methylobacterium hispanicum EM2 strain (EM2) was newly isolated from mine tailing soil, and we investigated its use as a biosorbent for treating a Pb(II)-contaminated aqueous solution. The EM2 strain was strongly resistant to Pb(II) up to a concentration of 800 mg/L, and achieved remarkable adsorption performance (adsorption rate and maximum adsorption capacity of 96% ± 3.2% and 79.84 mg/g, respectively) under optimal conditions (pH, biomass content, contact time, and initial Pb(II) concentration of 7.1 g/L, 60 min, and 10 mg/L, respectively). The adsorption of Pb(II) was characterized by scanning electron microscopy-energy dispersive x-ray spectroscopy and Fourier-transform infrared analysis. The equilibrium data matched the Freundlich isotherm model well, indicating the occurrence of multilayer adsorption of Pb(II) onto the heterogeneous surface of the EM2 strain, which was also consistent with the pseudo-second-order kinetic model (R2 = 0.98). The high Pb(II) removal efficiency was also confirmed by conducting an adsorption experiment using Pb(II)-contaminated industrial wastewater.

Sign in / Sign up

Export Citation Format

Share Document