High-Performance Thermal Grease with the Addition of Silver Particles

Author(s):  
Xiangliang Zeng ◽  
Zhenyu Wang ◽  
Wenbo Ye ◽  
Linlin Ren ◽  
Xiaoliang Zeng ◽  
...  
2000 ◽  
Author(s):  
Ravi S. Prasher ◽  
Craig Simmons ◽  
Gary Solbrekken

Abstract Thermal interface material (TIM) between the die and the heat spreader or between the heat spreader and the heat sink in any electronic package plays a very important role in the thermal management of electronic cooling. Due to increased power and power density high-performance TIMs are sought every day. Phase change materials (PCM) seem to be very good alternative to traditionally used thermal greases because of various reasons. These phase change materials also have the advantage of being reworked easily without damaging the die. Typically these phase change materials are polymer based and are particle laden to enhance their thermal conductivity. The thermal conductivity of these materials is relatively well understood than their contact resistance. Current work focuses on explicitly measuring the contact resistance and the thermal conductivity of a particular phase change TIM and some silicon-based greases. Effect of various parameters, which can affect the contact resistance of theses TIMs and Greases, are also captured. The steady state measurements of the thermal conductivity and the contact resistance was done on an interface tester. In general the work on the contact resistance of fluid-like polymer based TIM, such as thermal grease or phase change polymer has been experimental in the past. A semi-analytical model, which captures the various parameters affecting the contact resistance of two class of materials; the phase change and the thermal grease is also developed in this paper. This model fits very well with the experimental data.


2020 ◽  
Vol 10 (3) ◽  
pp. 1112 ◽  
Author(s):  
Ali Yahyaee ◽  
Amir Bahman ◽  
Frede Blaabjerg

For reliability and thermal management of power devices, the most frequently used technique is to employ heatsinks. In this work, a new configuration of offset strip fin heatsink based on using the concept of curvy fins and U-turn is proposed with the aim of improving the heat transfer performance. With this aim, a three-dimensional model of heatsink with Silicon Insulated-Gate Bipolar Transistors (IGBTs) and diodes, solder, Direct Bonded Copper (DBC) substrate, baseplate and thermal grease is developed. Richardson’s extrapolation is used for increasing the accuracy of the numerical simulations and to validate the simulations. To study the effectiveness of the new offset design, results are compared with conventional offset strip fin heatsink. Results show that in aspects of design of heatsinks (including heat transfer coefficient, maximum chip temperature and thermal resistance), the new introduced model has advantages compared to the conventional offset strip fin design. These enhancements are caused by the combination of the longer coolant passage in the heatsink associated with generation of disturbance and recirculation areas along the curvy fins, creation of centrifugal forces in the U-turn, and periodic breaking up boundary layers. Also, it is shown that due to narrower passage and back-and-forth route, the new introduced design can handle the hot spots better than conventional design.


Author(s):  
Paul Paret ◽  
Joshua Major ◽  
Douglas DeVoto ◽  
Sreekant Narumanchi ◽  
Yansong Tan ◽  
...  

Sintered silver-based bonded interfaces are a critical enabling technology for high-temperature, compact, high-performance, and reliable wide-bandgap packages and components. High-pressure (∼40 MPa) sintered silver interfaces have been implemented commercially, most notably the commercial products offered by Semikron. To reduce manufacturing complexity, there is significant industry interest in pressure-less sintered silver interfaces. To this end, current formulations of sintered silver paste are comprised of purely nano-sized silver particles or a combination of nano- and micro-sized silver particles/flakes. It is essential to quantify the mechanical properties and determine the reliability of these interfaces prior to use in automotive power electronics applications. In this paper, research efforts at the National Renewable Energy Laboratory, in collaboration with Virginia Polytechnic Institute and State University and an industry partner, in optimizing the synthesis procedure and mechanical characterization of sintered silver double-lap samples are described. These double-lap samples were synthesized using pressure-less sintering techniques. Shear testing was conducted at multiple temperatures and displacement rates on these samples sintered using two types of sintered sintered silver pastes, one of them consisting of nano-silver particles and the other a hybrid paste or a combination of nano- and micron-sized silver flakes, employed in a double-lap configuration. Maximum values of shear stress obtained from the characterization study are reported.


2017 ◽  
Vol 41 (23) ◽  
pp. 14342-14350 ◽  
Author(s):  
Hongji Li ◽  
Xiaonan Wang ◽  
Zirun Wang ◽  
Jiaqi Jiang ◽  
Yu Qiao ◽  
...  

Ag-MIPs were prepared through a multistep procedure, in which MPS and LC were selected as the template molecules. These materials could selectively rebind the templates and could be detected using Raman spectroscopy.


Author(s):  
Vadim A. Plakhin ◽  
◽  
Yuriy G. Khabarov ◽  
Viacheslav A. Veshnyakov

Colloidal silver solutions can be used as catalysts for carrying out various chemical transformations of organic substances and solving the problems of disposal of toxic compounds, as well as antibacterial agents for combating pathogenic microflora, in the manufacture of lubricants and light-absorbing materials, coatings, sensors, conductive pastes, and high-performance electrode materials. The research purpose is to study the synthesis of colloidal silver using a solution of technical lignosulfonates (LST) as a stabilizer. Colloidal silver was synthesized as a result of the reduction-oxidation (redox) reaction of Ag(I) cations with glucose at 100 °C in the presence of lignosulfonates. The reaction was carried out in an alkaline medium, which is provided by the addition of ammonia water. Electronic spectroscopy was used to control the synthesis of colloidal silver. After the reaction, the solution turned dark brown and an intense absorption band with a maximum at 400 nm appeared on the electron spectra. The effects of reagent consumption and synthesis duration were studied. It was found that the optimal reagent consumption in the colloidal silver synthesis is as follows: 2.5–5 g glucose / g Ag, 0.3–1 g LST / g Ag, and 3–5 g NH3 / g Ag. The synthesis duration is 2–5 min. The resulting colloidal silver solution is stable for several months. Partial stratification without precipitation is observed during the solution storage. It is shown experimentally that the stratification is followed by a redistribution of colloidal silver particles. Electron spectroscopy confirmed the absence of colloidal silver particles in the upper layer. The reaction kinetics has been studied in experiments carried out under thermostatically controlled conditions at temperatures from 50 to 100 °C. The kinetic dependence is described by a first-order equation at the initial stage of the reaction, the duration of which depends on the temperature. The duration of the active part of the kinetic curves is 15–90 % of the total reaction time. The logarithm of the rate constant on the active section was proved to depend linearly on the reverse thermodynamic temperature (pair correlation coefficient is 0.9887). The activation energy was 47 kJ/mol. For citation: Plakhin V.A., Khabarov Yu.G., Veshnyakov V.A. Synthesis of Colloidal Silver Using Lignosulfonates. Lesnoy Zhurnal [Russian Forestry Journal], 2021, no. 6, pp. 184–195. DOI: 10.37482/0536-1036-2021-6-184-195


2021 ◽  
Vol 880 ◽  
pp. 71-76
Author(s):  
Haneul Kang ◽  
Hyunji Kim ◽  
Sunghoon Im ◽  
Jinho Yang ◽  
Sunchul Huh

An increase in power consumption density is related to the internal thermal characteristics of an electronic device, and the heat dissipation of the device is directly related to the high performance and miniaturization of the device. TIM (thermal interface material) with excellent internal heat dissipation performance are mainly used to improve the heat dissipation performance of electronic devices. Recently, the need for a high-efficiency TIM with high-performance thermal conductivity and low thermal contact resistance has increased. In this study, thermal grease was prepared by mixing Cu-Ni nanopowders with silicon oil, the thermal grease was then used as a heat transfer material. Compared to silicone thermal grease, the thermal conductivity of all prepared samples was excellent. In particularly, thermal conductivity was improved by about maximum 212% compared to that of thermal silicone of thermal grease mixed with Cu-Ni powder.


2018 ◽  
Vol 284 ◽  
pp. 48-53 ◽  
Author(s):  
R.A. Shishkin ◽  
A.P. Zemlyanskaya ◽  
A.R. Beketov

A huge increase in performance of devices within the sizes and weight decrease result in high performance thermal interface materials (TIM) are indispensable to application. Thermal grease is one of the most commonly used TIM types. Zinc-oxide based thermal grease (KPT-8) has a low thermal conductivity that leads to overheating. New silicone oil – aluminum nitride high performance thermal grease has been studied. Also the installation for thermal conductivity investigation has been designed and produced. Thermal conductivity value of aluminum nitride-silicone oil thermal grease with 50 % volume fraction was 1,130±0,056 W/(m K), that is 40 % higher than KPT-8 thermal conductivity. Thermal conductivity value was calculated by a number of theoretical models, and the results were compared to the experimental data. The best results have been obtained by modeling within Brugemman and Cheng-Vachon theories.


Author(s):  
A. V. Crewe ◽  
M. Isaacson ◽  
D. Johnson

A double focusing magnetic spectrometer has been constructed for use with a field emission electron gun scanning microscope in order to study the electron energy loss mechanism in thin specimens. It is of the uniform field sector type with curved pole pieces. The shape of the pole pieces is determined by requiring that all particles be focused to a point at the image slit (point 1). The resultant shape gives perfect focusing in the median plane (Fig. 1) and first order focusing in the vertical plane (Fig. 2).


Author(s):  
N. Yoshimura ◽  
K. Shirota ◽  
T. Etoh

One of the most important requirements for a high-performance EM, especially an analytical EM using a fine beam probe, is to prevent specimen contamination by providing a clean high vacuum in the vicinity of the specimen. However, in almost all commercial EMs, the pressure in the vicinity of the specimen under observation is usually more than ten times higher than the pressure measured at the punping line. The EM column inevitably requires the use of greased Viton O-rings for fine movement, and specimens and films need to be exchanged frequently and several attachments may also be exchanged. For these reasons, a high speed pumping system, as well as a clean vacuum system, is now required. A newly developed electron microscope, the JEM-100CX features clean high vacuum in the vicinity of the specimen, realized by the use of a CASCADE type diffusion pump system which has been essentially improved over its predeces- sorD employed on the JEM-100C.


Sign in / Sign up

Export Citation Format

Share Document