EFFECT OF UV RADIATION DURATION AND MOLECULAR WEIGHT TO HYDROPHOBICITY AND SURFACE ROUGHNESS OF POLYSTYRENE COATING ON QCM SENSOR

2017 ◽  
Vol 79 (3) ◽  
Author(s):  
Setyawan P. Sakti ◽  
Layli Amaliya ◽  
Nike F. Khusnah ◽  
Masruroh Masruroh
Keyword(s):  
Molecular Weight ◽  
Surface Roughness ◽  
Contact Angle ◽  
Uv Radiation ◽  
Uv Light ◽  
Hydrophobic Surface ◽  
Surface Radiation ◽  
Coating Materials ◽  
Optical Profilometer ◽  
Uv Lamp

Hydrophobicity is one of important solid surface properties for the development of Quartz Crystal Microbalance (QCM) biosensor. Hydrophobicity plays a role in the biomolecule immobilisation. Polystyrene is one of the coating materials used in the QCM biosensor, where the sensitive biomolecule material is immobilised. Hydrophobicity and surface roughness can be controlled by many methods. In this work, we investigated the effect of the polymer molecular weight and UV radiation on the surface roughness and hydrophobicity. The polystyrene with a molecular weight of 35,000 g/mol, 192,000 g/mol, and 280.000 g/mol were solved in toluene with a concentration of 3%, 5%, and 7% and coated using spin coating method on top of the QCM sensor. The coated polystyrene on QCM sensor was irradiated using UV lamp with a wavelength of 254 nm. The contact angle of water before and after UV irradiated was measured using contact angle instrument and the surface roughness is measured using non-contact optical profilometer. The result shows that the higher molecular weight of polystyrene led to more hydrophobic surface. Radiation under UV light increases the hydrophobicity of polystyrene surface. The surface roughness of the polystyrene on top of the sensor is not affected by UV irradiation. 

Enhancing the Strengths of Adhesion Bonds Between Composite Surface and Coating via UV Treatments

2017 ◽  
Author(s):  
R. Asmatulu ◽  
K. S. Erukala ◽  
M. M. Rahman
Keyword(s):  
Contact Angle ◽  
Uv Radiation ◽  
Uv Light ◽  
Composite Coatings ◽  
Weight Ratio ◽  
High Strength ◽  
Water Contact ◽  
Composite Surface ◽  
Adhesion Properties ◽  
Infrared Spectrometer

Field of composites is rapidly growing in many industries such as aviation, energy and automotive industries. Composites are known to have a high strength to low weight ratio. Significant improvement in the performance of coatings used in the protection of military and civil aircraft has been achieved the last thirty years. Composite coatings are exposed to many environmental conditions, which can significantly affect their properties. In this research, UV light treatment on the surface of composite was introduced to examine its effects on the adhesion properties between the coating and substrate. A cross-cut test was conducted on the composite panels to assess the adhesion of paint to the substrate after the treatments. Coating performance analyses were also carried out using a Fourier transform infrared spectrometer, water contact angle, and optical microscopic images. The first set of panels was treated with UV radiation for 0, 2, 4 and, 8 days, and the surface wettability was also assessed using the contact angle test. Two coats of paints, including a primer and top coat, were used, and the panels were exposed to UV radiation and immersed in water for 500 hrs and 1000 hrs. It was found that untreated panels showed a much higher contact angle of 106°, whereas the contact angle of panels treated with UV radiation was reduced to 47°. The cross-cut tests showed considerable flaking of the coating along the edges and squares of panels that were not treated, and very small flakes along the edges and parts of the grid square on panels that were UV treated, thus confirming the enhancement of coating adhesion between composite and coating surfaces by UV treatments.

scholarly journals Influence of laser power in nanosecond laser texturing for a hydrophobic state on SS316L

2021 ◽  
Vol 15 (4) ◽  
pp. 8592-8600
Author(s):  
M.H. Zul ◽  
Mahadzir Ishak@Muhammad ◽  
M. H. Aiman ◽  
M. M. Quazi
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Laser Power ◽  
Surface Engineering ◽  
Hydrophobic Surface ◽  
Morphological Properties ◽  
Nanosecond Laser ◽  
Time Interval ◽  
Beam Diameter ◽  
Laser Texturing

The use of lasers in surface engineering has recently made significant progress. The hydrophobic surface is commonly studied because of the application in various fields, including vehicles, aerospace, biomedicine, etc. Since these laser methods require many combination parameters, such as laser power (P), frequency (ƒ), scan speed (ʋ) and laser beam diameter (D), the effect of the parameters must therefore be investigated to produce the hydrophobic condition. This research tries to relate the laser power with the morphological properties and contact angle of the SS316L surfaces. Samples are subjected to laser texturing with different laser power settings. The surface is then characterised by surface roughness, and the contact angle is measured according to a specific time interval. The laser power output and energy density function on the surface and contact angle were investigated in these contexts experimentally. Surface roughness was defined and validated to show that the laser parameters' effect is effective and controllable. This study shows that the laser output intensity significantly contributes to regulating surface roughness and the substrate's wetting activity. The 18W and 24W laser outputs produce a spiked surface with various peaks that cause the surface to become hydrophobic over time because of the air-trap that happens in the valley.

Roughness Effects on Continuous and Discrete Flows in Superhydrophobic Microchannels

2011 ◽  
Vol 9 (5) ◽  
pp. 1094-1105 ◽  
Author(s):  
Junfeng Zhang ◽  
Daniel Y. Kwok
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Slip Length ◽  
Contact Angle Hysteresis ◽  
Hydrophobic Surface ◽  
Contact Angles ◽  
Lattice Boltzmann Model ◽  
Roughness Effects ◽  
Apparent Slip ◽  
Velocity Changes

AbstractThe dynamic behaviors of continuous and discrete flows in superhydrophobic microchannels are investigated with a lattice Boltzmann model. Typical characters of the superhydrophobic phenomenon are well observed from our simulations, including air trapped in the surface microstructures, high contact angles, low contact angle hysteresis, and reduced friction to fluid motions. Increasing the roughness of a hydrophobic surface can produce a large flow rate through the channel due to the trapped air, implying less friction or large apparent slip. The apparent slip length appears to be independent to the channel width and could be considered as a surface property. For a moving droplet, its behavior is affected by the surface roughness from two aspects: the contact angle difference between its two ends and the surface-liquid interfacial friction. As a consequence, the resulting droplet velocity changes with the surface roughness as firstly decreasing and then increasing. Simulation results are also compared with experimental observations and better agreement has been obtained than that from other numerical method. The information from this study could be valuable for microfluidic systems.

scholarly journals THE INFLUENCE OF SILICA CALCINATION TEMPERATURE VARIATION TO THE HYDROPHOBICITY AND TRANSMITTANCE ON GLASS SUBSTRATE

2020 ◽  
Vol 12 (2) ◽  
pp. 49-56
Author(s):  
Roihatur Rohmah ◽  
Mochamad Zainuri
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Calcination Temperature ◽  
Water Contact Angle ◽  
Hydrophobic Surface ◽  
Dip Coating ◽  
Water Contact ◽  
Coating Method ◽  
Composite Filler ◽  
Dip Coating Method

The hydrophobic surface can be self-cleaning. The hierarchy of surface roughness affects the hydrophobic surface. In this research, the hydrophobic surface was fabricated by modification of surface roughness from the composite filler. Natural silica was used as a filler and was done a variation of calcination temperature to modify the hierarchy of roughness formed. The variation of calcination temperature was 800°C, 1000°C, 1200°C, and 1400°C. The coating method was a dip-coating method by 30-second long immersion. A glass as coating media was coated by PVDF/SiO2 composite. The hydrophobic surface could be known from the value of the water contact angle (WCA) formed. If a water contact angle more than 90°, the surface could be called the hydrophobic surface. In this research, the hydrophobicity aspect cause of variation of calcination temperature was known from the value of water contact angle formed on the surface of PVDF/SiO2 composite coating 800°C, 1000°C, 1200°C, and 1400°C was 117,12° ± 0,98°, 107,80° ± 0,91°, 121,31° ± 1,45°, and 111,75° ± 1,47°, respectively.

scholarly journals Surface Characterization and Assessment of Biofilm Formation on Two Titanium-Based Implant Coating Materials

2021 ◽  
Vol 2 ◽  
Author(s):  
Bhumika Shokeen ◽  
Leila Zamani ◽  
Sara Zadmehr ◽  
Sevda Pouraghaie ◽  
Ryotaro Ozawa ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Biofilm Formation ◽  
Growth Conditions ◽  
Bacterial Attachment ◽  
Coating Materials ◽  
Time Points ◽  
Ticn Coating ◽  
Implant Coating ◽  
Coated Surfaces

Implant-related oral diseases such as peri-implantitis and peri-mucositis are largely initiated by bacterial colonization on artificial implant surfaces. Therefore, implant and abutment material characteristics that minimize bacterial attachment and subsequent biofilm formation are important factors in reducing the risk of infection-related implant failure. This study compares the properties of two different titanium-based implant coating materials, titanium nitride (TiN) and titanium carbon nitride (TiCN). Surface hydrophilicity/ hydrophobicity and roughness were evaluated via contact angle measurements and surface profiling with white light interferometry, respectively. TiN-coated surfaces were hydrophobic according to its contact angle higher than 72.7°, whereas TiCN-coated surfaces were hydrophilic with its contact angle of 53.6°. The average roughness (Ra) was greater for TiCN than TiN with the root mean square roughness (Rq) being significantly higher. These findings are in contrast to the common understanding for titanium-based materials that surface roughness and hydrophobicity are positively correlated. A well-established saliva-based oral microbial biofilm model was employed to compare bacterial attachment and biofilm formation on TiN and TiCN. Growth conditions included relevant host components such as blood as well as the presence or absence of dietary carbohydrates. The accumulated biomass was measured by crystal violet staining and the bacterial community profiles of the attached biofilms were determined via 16S rRNA gene microbiome sequencing at different time points over a 7-day period. At all time points, TiCN showed significantly less bacterial attachment and biofilm formation compared to TiN. This implied the importance of the hydrophilic state over surface roughness as parameter for the prevention of oral microbial attachment. Although, the biofilm community composition was very similar on both materials, environmental growth conditions resulted in significantly different bacterial profiles independent of the surface. In conclusion, TiCN coating produced a unique titanium surface which is rougher but more hydrophilic. TiCN-coated surfaces exhibited reduced bacterial attachment and biofilm formation in comparison to TiN coating. This coating technique can be further explored to improve implant and abutment success.

scholarly journals Polylactic acid scaffolds obtained by 3D printing and modified by oxygen plasma

2020 ◽  
Vol 23 (1) ◽  
Author(s):  
Hernane Silva Barud ◽  
Lorenzo Gouvêa Machado ◽  
Mayté Paredes Zaldivar ◽  
Mônica Rosas da Costa Iemma ◽  
Sandra Andrea Cruz ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Surface Roughness ◽  
Contact Angle ◽  
3D Printing ◽  
Cell Viability ◽  
Polylactic Acid ◽  
Oxygen Plasma ◽  
Hydrophobic Surface ◽  
Surface Modifications ◽  
Thermoplastic Polymer

The purpose of tissue engineering is to repair, replace, and regenerate tissues and organs. For this aim, materials supports, as polylactic acid (PLA) are used. PLA is a thermoplastic polymer that presents biodegradability, biocompatibility and good processability. PLA scaffolds can accurately constructed by 3D printing. Then, the objectives of this work were to modify the hydrophobic surface of PLA scaffolds using oxygen plasma and to study the cell viability and proliferation. The characterization was done by AFM, contact angle, FTIR and studies of proliferation and cell viability. Results showed that the material acquired hydrophilic properties by the presence of oxygen reactive species and by contact angle decrease. It was also observed an increase in the surface roughness. We can conclude that although the surface modifications were effective and the PLA scaffolds were not cytotoxic, there were no improvements in the proliferation process with the studied osteo-1 lineage cells. 

UV Irradiation of Shell Eggs: Effect on Populations of Aerobes, Molds, and Inoculated Salmonella typhimurium

1997 ◽  
Vol 60 (6) ◽  
pp. 639-643 ◽  
Author(s):  
FUENG-LIN KUO ◽  
JOHN B. CAREY ◽  
STEVEN C. RICKE
Keyword(s):  
Salmonella Typhimurium ◽  
Uv Radiation ◽  
Uv Light ◽  
The Other ◽  
Uv Exposure ◽  
Microbial Populations ◽  
Aerobic Bacteria ◽  
Fluorescent Light ◽  
Uv Treatment ◽  
Shell Eggs

The effects were investigated of 254-nm UV radiation on populations of Salmonella typhimurium, aerobes, and molds on the shells of eggs. In the first experiment, the CFU of attached S. typhimurium cells on unwashed clean shell eggs were determined after 0, 1, 3, 5, and 7 min of UV treatment (620 μW/cm2) on both ends of the egg. All UV treatments significantly reduced S. typhimurium CFU (P < .01). UVtreatment (620 μW/cm2) in 1-min alternating light and dark cycles for 5 min (three light and two dark) was compared to 0, 3, and 5 min of UV treatment. No significant differences in microbial populations were observed among light and dark cycles and the other UV treatments. In a subsequent experiment, the same UV treatments were utilized to evaluate photoreactivation. After UV exposure, eggs were exposed to 1 h of fluorescent light or I h of darkness or cultured immediately. S. typhimurium CFU were significantly (P < .01) reduced by the UV treatments. However, no significant differences between microbial populations exposed to UV treatment and UV radiation plus photoreactivation were detected. For studies of aerobic bacteria and molds, different UV treatment times (0, 15, and 30 min) at the intensity of 620 μW/cm2 and different intensities (620, 1350, and 1720 μW/cm2) for 15 min were evaluated. Mold CFU per egg were either 0 or 1 for all UV treatments and a 99% reduction of CFU of aerobic bacteria per egg were observed for all UV treatments. It appears from these studies that UV light can significantly reduce populations of S. typhimurium, aerobes, and molds on shell eggs.

scholarly journals Hard Coating Materials Based on Photo-Reactive Silsesquioxane for Flexible Application: Improvement of Flexible and Hardness Properties by High Molecular Weight

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1564
Author(s):  
Jong Tae Leem ◽  
Woong Cheol Seok ◽  
Ji Beom Yoo ◽  
Sangkug Lee ◽  
Ho Jun Song
Keyword(s):  
Molecular Weight ◽  
Surface Morphology ◽  
High Molecular Weight ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Polyhedral Oligomeric Silsesquioxanes ◽  
Coating Materials ◽  
Pencil Hardness ◽  
Coated Film ◽  
Flexible Application

EPOSS of polyhedral oligomeric silsesquioxanes (POSS) mixture structure and LPSQ of ladder-like polysilsesquioxane (LPSQ) structure were synthesized via sol–gel reaction. EPSQ had a high molecular weight due to polycondensation by potassium carbonate. The EPSQ film showed uniform surface morphology due to regular double-stranded structure. In contrast, the EPOSS-coated film showed nonuniform surface morphology due to strong aggregation. Due to the aggregation, the EPOSS film had shorter d-spacing (d1) than the EPSQ film in XRD analysis. In pencil hardness and nanoindentation analysis, EPSQ film showed higher hardness than the EPOSS film due to regular double-stranded structure. In addition, in the in-folding (r = 0.5 mm) and out-folding (r = 5 mm) tests, the EPSQ film did not crack unlike the EPOSS coated film.

scholarly journals Impact of Macrodiols on the Morphological Behavior of H12MDI/HDO-Based Polyurethane Elastomer

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2060
Author(s):  
Shazia Naheed ◽  
Mohammad Zuber ◽  
Mahwish Salman ◽  
Nasir Rasool ◽  
Zumaira Siddique ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Contact Angle ◽  
Chain Length ◽  
Microphase Separation ◽  
Soft Segment ◽  
Group Identification ◽  
Degree Of Crystallinity ◽  
Polyurethane Elastomers ◽  
Hard Segments ◽  
Morphological Behavior

In this study, we evaluated the morphological behavior of polyurethane elastomers (PUEs) by modifying the soft segment chain length. This was achieved by increasing the soft segment molecular weight (Mn = 400–4000 gmol−1). In this regard, polycaprolactone diol (PCL) was selected as the soft segment, and 4,4′-cyclohexamethylene diisocyanate (H12MDI) and 1,6-hexanediol (HDO) were chosen as the hard segments. The films were prepared by curing polymer on Teflon surfaces. Fourier transform infrared spectroscopy (FTIR) was utilized for functional group identification in the prepared elastomers. FTIR peaks indicated the disappearance of −NCO and −OH groups and the formation of urethane (NHCOO) groups. The morphological behavior of the synthesized polymer samples was also elucidated using scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques. The AFM and SEM results indicated that the extent of microphase separation was enhanced by an increase in the molecular weight of PCL. The phase separation and degree of crystallinity of the soft and hard segments were described using X-ray diffraction (XRD). It was observed that the degree of crystallinity of the synthesized polymers increased with an increase in the soft segment’s chain length. To evaluate hydrophilicity/hydrophobicity, the contact angle was measured. A gradual increase in the contact angle with distilled water and diiodomethane (38.6°–54.9°) test liquids was observed. Moreover, the decrease in surface energy (46.95–24.45 mN/m) was also found to be inconsistent by increasing the molecular weight of polyols.

MICROSTRUCTURE ANALYSIS OF MOSO BAMBOO (Phyllostachys pubescens MAZEL) SURFACE AFTER UV RADIATION

2019 ◽  
Vol 27 (01) ◽  
pp. 1950090
Author(s):  
HAIXIA YU ◽  
XIN PAN ◽  
WEIMING YANG ◽  
WENFU ZHANG ◽  
XIAOWEI ZHUANG
Keyword(s):  
Uv Radiation ◽  
Cell Walls ◽  
Uv Light ◽  
Parenchyma Cell ◽  
Moso Bamboo ◽  
Thick Wall ◽  
Phyllostachys Pubescens ◽  
Thin Wall ◽  
Intercellular Spaces ◽  
Parenchyma Cell Walls

Bamboo material is widely used in outdoor applications. However, they are easily degraded when exposed to sunlight, their smooth surface will gradually turn to rough, and small cracks will appear and finally develop to large cracks. The paper presents a first-time investigation on the microstructure changes in the tangential section of Moso bamboo (Phyllostachys pubescens Mazel) radiated by artificial UV light. The results showed that the cracks mainly appeared at intercellular spaces of fibers where lignin content was high, the parenchyma cell walls and neighbor pits where the cell wall was very thin and more vulnerable than the other parts. In addition, the part of raised area and pit cavity tended to absorb more UV light radiation and showed more and larger cracks than the otherwhere. Cracks at the intercellular spaces of fibers were larger and bigger than those on the parenchyma cell walls. The cracks on the pits of the parenchyma cell walls normally appeared at one pit and then extended to the several surrounding pits. Bordered pits cavity showed more and larger cracks than the pits on the thin wall cells. The simple pits on the thick wall cells and the fiber cells were unaffected by UV radiation.

Sign in / Sign up

Export Citation Format

Share Document