scholarly journals The Aerodynamic and Mechanical Performance of a High-Pressure Turbine Stage in a Transient Wind Tunnel

1992 ◽  
Vol 114 (1) ◽  
pp. 132-140 ◽  
Author(s):  
A. G. Sheard ◽  
R. W. Ainsworth
Keyword(s):  
High Pressure ◽  
Mechanical Performance ◽  
Mechanical Design ◽  
Unsteady Aerodynamics ◽  
Operating Conditions ◽  
Test Facility ◽  
Operating Point ◽  
High Pressure Turbine ◽  
Transient Wind ◽  
Future Work

A new transient facility for the study of time mean and unsteady aerodynamics and heat transfer in a high-pressure turbine has been commissioned and results are available. A detailed study has been made of aspects of the performance and behavior relevant to turbine mechanical design, and an understanding of the variation of the turbine operating point during the test, crucial to the process of valid data acquisition, has been obtained. In this this paper the outline concept and mode of operation of the turbine test facility are given, and the key aerodynamic and mechanical aspects of the facility’s performance are presented in detail. The variations of the those parameters used to define the turbine operating point during facility operation are examined, and the accuracy with which the turbine’s design point was achieved calculated. Aspects of the mechanical performance presented include the results of a finite element stress analysis of the loads in the turbine under operating conditions, and the performance of the rotor bearing system under these arduous load conditions. Both of these aspects present more information than has been available hitherto. Finally, the future work program and possible plans for further facility improvement are given.

scholarly journals The Aerodynamic and Mechanical Performance of a High Pressure Turbine Stage in a Transient Wind Tunnel

1990 ◽  
Author(s):  
A. G. Sheard ◽  
R. W. Ainsworth
Keyword(s):  
High Pressure ◽  
Mechanical Performance ◽  
Mechanical Design ◽  
Unsteady Aerodynamics ◽  
Operating Conditions ◽  
Test Facility ◽  
Operating Point ◽  
High Pressure Turbine ◽  
Transient Wind ◽  
Future Work

A new transient facility for the study of time mean and unsteady aerodynamics and heat transfer in a high pressure turbine has been commissioned and results are available. A detailed study has been made of aspects of the performance and behaviour relevant to turbine mechanical design, and an understanding of the variation of the turbine operating point during the test, crucial to the process of valid data acquisition, has been obtained. In this paper the outline concept and mode of operation of the tubine test facility are given, and the key aerodynamic and mechanical aspects of the facility’s performance are presented in detail. The variation of those parameters used to define the turbine operating point during facility operation are examined, and the accuracy with which the turbine’s design point was achieved calculated. Aspects of the mechanical performance which are presented include the results of a finite element stress analysis of the loads in the turbine under operating conditions, and the performance of the rotor bearing system under these arduous load conditions. Both of these aspects present more information than has been available hitherto. Finally, the future work programme and possible plans for further facility improvement are given.

scholarly journals Calculation and Correlation of the Unsteady Flowfield in a High Pressure Turbine

2002 ◽  
Author(s):  
Milind A. Bakhle ◽  
Jong S. Liu ◽  
Josef Panovsky ◽  
Theo G. Keith ◽  
Oral Mehmed
Keyword(s):  
High Pressure ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Forced Vibrations ◽  
Forced Response ◽  
Operating Conditions ◽  
Test Facility ◽  
Navier Stokes ◽  
Turbine Stage ◽  
High Pressure Turbine

Forced vibrations in turbomachinery components can cause blades to crack or fail due to high-cycle fatigue. Such forced response problems will become more pronounced in newer engines with higher pressure ratios and smaller axial gap between blade rows. An accurate numerical prediction of the unsteady aerodynamics phenomena that cause resonant forced vibrations is increasingly important to designers. Validation of the computational fluid dynamics (CFD) codes used to model the unsteady aerodynamic excitations is necessary before these codes can be used with confidence. Recently published benchmark data, including unsteady pressures and vibratory strains, for a high-pressure turbine stage makes such code validation possible. In the present work, a three dimensional, unsteady, multi blade-row, Reynolds-Averaged Navier Stokes code is applied to a turbine stage that was recently tested in a short duration test facility. Two configurations with three operating conditions corresponding to modes 2, 3, and 4 crossings on the Campbell diagram are analyzed. Unsteady pressures on the rotor surface are compared with data.

Development and Testing of the Upgraded High Pressure Turbine Section for an Industrial Gas Turbine

2008 ◽  
Author(s):  
E. Aschenbruck ◽  
D. Frank ◽  
T. Korte ◽  
R. Mu¨ller ◽  
U. Orth
Keyword(s):  
High Pressure ◽  
Gas Turbine ◽  
Cooling System ◽  
Mechanical Design ◽  
Development Program ◽  
Tip Clearance ◽  
Test Facility ◽  
High Pressure Turbine ◽  
Online Data ◽  
Clearance Control

As part of an ongoing development program to increase power output and efficiency of the THM 1304 gas turbine, modifications were made to the high pressure turbine. The modifications include but are not limited to blade and vane aerodynamics, cooling system and clearance control, mechanical design and materials. The development was to achieve the following goals: • Intensified blade and vane cooling to permit higher turbine inlet temperatures and to further extend service lifetime; • Improved aerodynamic performance; • Blades with pre-loaded tip shrouds to achieve low vibration amplitudes in a broad operating speed range; • Rotor design modifications to simplify assembly and disassembly; • Modified vane carrier and casing designs for optimal tip clearance control and turbine performance. The improved high pressure turbine was extensively tested in MAN TURBO’s full-load gas turbine test facility. Test results verified that component temperatures were within the expected range and design targets have been achieved. The first production gas turbine equipped with the upgraded high pressure turbine was installed in May 2004 as a gas compressor driver. To date a total of 11 units have gone into operation including units for power generation. Dry low emission technology is used on all engines. Every unit is monitored by an online data monitoring system and visually inspected in shorter intervals to verify the behavior in the field. Operation of the fleet is flawless at this time.

Time-Accurate Predictions for a Fully Cooled High-Pressure Turbine Stage—Part I: Comparison of Predictions With Data

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
S. A. Southworth ◽  
M. G. Dunn ◽  
C. W. Haldeman ◽  
J.-P. Chen ◽  
G. Heitland ◽  
...  
Keyword(s):  
High Pressure ◽  
Power Spectrum ◽  
Surface Pressure ◽  
Pressure Ratio ◽  
Computing Time ◽  
Flow Simulation ◽  
Operating Conditions ◽  
Test Facility ◽  
High Pressure Turbine ◽  
Cooling Flow

The aerodynamics of a fully cooled axial single stage high-pressure turbine operating at design corrected conditions of corrected speed, flow function, and stage pressure ratio has been investigated. This paper focuses on flow field predictions obtained from the viewpoint of a turbine designer using the computational fluid dynamics (CFD) codes Numeca’s FINE/TURBO and the code TURBO. The predictions were all performed with only knowledge of the stage operating conditions, but without knowledge of the surface pressure measurements. Predictions were obtained with and without distributed cooling flow simulation. The FINE/TURBO model was run in 3-D viscous steady and time-accurate modes; the TURBO model was used to provide only 3-D viscous time-accurate results. Both FINE/TURBO and TURBO utilized phase-lagged boundary conditions to simplify the time-accurate model and to significantly reduce the computing time and resources. The time-accurate surface pressure loadings and steady state predictions are compared to measurements for the blade, vane, and shroud as time-averaged, time series, and power spectrum data. The measurements were obtained using The Ohio State University Gas Turbine Laboratory Turbine Test Facility. The time-average and steady comparisons of measurements and predictions are presented for 50% span on the vane and blade. Comparisons are also presented for several locations along the blade to illustrate local differences in the CFD behavior. The comparisons for the shroud are made across the blade passage at axial blade chord locations corresponding to the pressure transducer locations. The power spectrum decompositions of individual transducers (based on the fast Fourier transform (FFT)) are also included to lend insight into the unsteady nature of the flow. The comparisons show that both computational tools are capable of providing reasonable aerodynamic predictions for the vane, blade, and stationary shroud. The CFD model predictions show the encouraging trend of improved matching to the experimental data with increasing model fidelity from mass averaged to distributed cooling flow inclusion and as the codes change from steady to time-accurate modes.

Validation of MISES Two-Dimensional Boundary Layer Code for High-Pressure Turbine Aerodynamic Design

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Philip L. Andrew ◽  
Harika S. Kahveci
Keyword(s):  
Boundary Layer ◽  
High Pressure ◽  
Operating Cost ◽  
Design Tool ◽  
Operating Conditions ◽  
Aerodynamic Design ◽  
High Pressure Turbine ◽  
Reduce Operating Cost ◽  
Wide Range ◽  
Dimensional Boundary

Avoiding aerodynamic separation and excessive shock losses in gas turbine turbomachinery components can reduce fuel usage and thus reduce operating cost. In order to achieve this, blading designs should be made robust to a wide range of operating conditions. Consequently, a design tool is needed—one that can be executed quickly for each of many operating conditions and on each of several design sections, which will accurately capture loss, turning, and loading. This paper presents the validation of a boundary layer code, MISES, versus experimental data from a 2D linear cascade approximating the performance of a moderately loaded mid-pitch section from a modern aircraft high-pressure turbine. The validation versus measured loading, turning, and total pressure loss is presented for a range of exit Mach numbers from ≈0.5 to 1.2 and across a range of incidence from −10 deg to +14.5 deg relative to design incidence.

Time-Averaged and Time-Accurate Aerodynamic Effects of Forward Rotor Cavity Purge Flow for a High-Pressure Turbine: Part I—Analytical and Experimental Comparisons

2012 ◽  
Author(s):  
Brian R. Green ◽  
Randall M. Mathison ◽  
Michael G. Dunn
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Flow Path ◽  
Field Analysis ◽  
High Pressure Turbine ◽  
Purge Flow

The effect of rotor purge flow on the unsteady aerodynamics of a high-pressure turbine stage operating at design corrected conditions has been investigated both experimentally and computationally. The experimental configuration consisted of a single-stage high-pressure turbine with a modern film-cooling configuration on the vane airfoil as well as the inner and outer end-wall surfaces. Purge flow was introduced into the cavity located between the high-pressure vane and the high-pressure disk. The high-pressure blades and the downstream low-pressure turbine nozzle row were not cooled. All hardware featured an aerodynamic design typical of a commercial high-pressure ratio turbine, and the flow path geometry was representative of the actual engine hardware. In addition to instrumentation in the main flow path, the stationary and rotating seals of the purge flow cavity were instrumented with high frequency response, flush-mounted pressure transducers and miniature thermocouples to measure flow field parameters above and below the angel wing. Predictions of the time-dependent flow field in the turbine flow path were obtained using FINE/Turbo, a three-dimensional, Reynolds-Averaged Navier-Stokes CFD code that had the capability to perform both steady and unsteady analysis. The steady and unsteady flow fields throughout the turbine were predicted using a three blade-row computational model that incorporated the purge flow cavity between the high-pressure vane and disk. The predictions were performed in an effort to mimic the design process with no adjustment of boundary conditions to better match the experimental data. The time-accurate predictions were generated using the harmonic method. Part I of this paper concentrates on the comparison of the time-averaged and time-accurate predictions with measurements in and around the purge flow cavity. The degree of agreement between the measured and predicted parameters is described in detail, providing confidence in the predictions for flow field analysis that will be provided in Part II.

Prevention of Low-Frequency Vibration of High-Capacity Steam Turbine Units

1997 ◽  
Author(s):  
H. Kanki ◽  
Y. Kaneko ◽  
M. Kurosawa ◽  
T. Yamamoto ◽  
Y. Yamamoto ◽  
...  
Keyword(s):  
High Pressure ◽  
High Capacity ◽  
Low Frequency ◽  
Field Tests ◽  
Operating Conditions ◽  
Squeeze Film ◽  
High Pressure Turbine ◽  
Solution Approach ◽  
Vibration Excitation ◽  
Low Frequency Vibration

Abstract The causes of low-frequency vibration (subsynchronous vibration) of a high pressure turbine were investigated analytically and also via vibration excitation tests on actual machines under operation. From the results, it was concluded that low-frequency vibrations may be caused by either the decrease of the rotor system damping or by external forces, such as flow disturbance in the control stage and the rubbing between the rotor and casing. After identifying the cause of the low-frequency vibration, appropriate countermeasures such as installation of a squeeze-film damper and modification of valve opening sequence were taken. Vibration measurements and vibration excitation tests for the high pressure turbine under actual operating conditions were carried out in order to verify the validity of the countermeasures. These field tests confirmed that the problems of low-frequency vibration can be solved completely by taking the appropriate countermeasure depending on the cause of the vibration. This paper presents some field experiences of low-frequency vibration and the effective solution approach.

Unsteady Aerodynamics and Interactions Between a High Pressure Turbine Vane and Rotor

2004 ◽  
Author(s):  
Ryan M. Urbassik ◽  
J. Mitch Wolff ◽  
Marc D. Polanka
Keyword(s):  
Experimental Data ◽  
High Pressure ◽  
Potential Field ◽  
Rotor Blade ◽  
Second Harmonic ◽  
Unsteady Aerodynamics ◽  
Pressure Measurements ◽  
High Pressure Turbine ◽  
Turbine Vane ◽  
Unsteady Pressure Measurements

A set of experimental data is presented investigating the unsteady aerodynamics associated with a high pressure turbine vane (HPV) and rotor blade (HPB). The data was acquired at the Turbine Research Facility (TRF) of the Air Force Research Laboratory. The TRF is a transient, blowdown facility generating several seconds of experimental data on full scale engine hardware at scaled turbine operating conditions simulating an actual engine environment. The pressure ratio and freestream Reynolds number were varied for this investigation. Surface unsteady pressure measurements on the HPV, total pressure traverse measurements downstream of the vane, and surface unsteady pressure measurements for the rotor blade were obtained. The unsteady content of the HPV surface was generated by the rotor potential field. The first harmonic decayed more rapidly than the second harmonic with a movement upstream causing the second harmonic to be most influential at the vane throat. The blade unsteadiness appears to be caused by a combination of shock, potential field, and vane wake interactions between the vane and rotor blade. The revolution averaged data resulted in higher unsteadiness than a passing ensemble average for both vane and rotor indicating a need to understand each passage for high cycle fatigue (HCF) effects.

Experimental Investigation of Vane Clocking in a One and 1/2 Stage High Pressure Turbine

2004 ◽  
Author(s):  
Charles W. Haldeman ◽  
Michael G. Dunn ◽  
John W. Barter ◽  
Brian R. Green ◽  
Robert F. Bergholz
Keyword(s):  
High Pressure ◽  
Low Pressure ◽  
Test Facility ◽  
Maximum Efficiency ◽  
High Pressure Turbine ◽  
Data Set ◽  
Time Resolved ◽  
Low Pressure Turbine ◽  
Turbine Vane ◽  
Vane Clocking

Aerodynamic measurements were acquired on a modern single-stage, transonic, high-pressure turbine with the adjacent low-pressure turbine vane row (a typical civilian one and one-half stage turbine rig) to observe the effects of low-pressure turbine vane clocking on overall turbine performance. The turbine rig (loosely referred to in this paper as the stage) was operated at design corrected conditions using the Ohio State University Gas Turbine Laboratory Turbine Test Facility (TTF). The research program utilized uncooled hardware in which all three airfoils were heavily instrumented at multiple spans to develop a full clocking dataset. The low-pressure turbine vane row (LPTV) was clocked relative to the high-pressure turbine vane row (HPTV). Various methods were used to evaluate the influence of clocking on the aeroperformance (efficiency) and the aerodynamics (pressure loading) of the LPTV, including time-resolved and time-averaged measurements. A change in overall efficiency of approximately 2–3% due to clocking effects is demonstrated and could be observed using a variety of independent methods. Maximum efficiency is obtained when the time-average surface pressures are highest on the LPTV and the time-resolved surface pressure (both in the time domain and frequency domain) show the least amount of variation. The overall effect is obtained by integrating over the entire airfoil, as the three-dimensional effects on the LPTV surface are significant. This experimental data set validates several computational research efforts that suggested wake migration is the primary reason for the perceived effectiveness of vane clocking. The suggestion that wake migration is the dominate mechanism in generating the clocking effect is also consistent with anecdotal evidence that fully cooled engine rigs do not see a great deal of clocking effect. This is consistent since the additional disturbances induced by the cooling flows and/or the combustor make it extremely difficult to find an alignment for the LPTV given the strong 3D nature of modern high-pressure turbine flows.

Investigation of Combustor-Turbine-Interaction in a Rotating Cooled Transonic High-Pressure Turbine Test Rig: Part 2 — Numerical Modelling and Simulation

2019 ◽  
Author(s):  
Simon Gövert ◽  
Federica Ferraro ◽  
Alexander Krumme ◽  
Clemens Buske ◽  
Marc Tegeler ◽  
...  
Keyword(s):  
High Pressure ◽  
Flame Stabilization ◽  
Test Facility ◽  
Test Rig ◽  
High Pressure Turbine ◽  
Lean Burn ◽  
Turbine Inlet ◽  
Measurement Results ◽  
Aero Engine ◽  
Inlet Conditions

Abstract Reducing the uncertainties in the prediction of turbine inlet conditions is a crucial aspect to improve aero engine designs and further increase engine efficiencies. To meet constantly stricter emission regulations, lean burn combustion could play a key role for future engine designs. However, these combustion systems are characterized by significant swirl for flame stabilization and reduced cooling air mass flows. As a result, substantial spatial and transient variations of the turbine inlet conditions are encountered. To investigate the effect of the combustor on the high pressure turbine, a rotating cooled transonic high-pressure configuration has been designed and investigated experimentally at the DLR turbine test facility ‘NG-Turb’ in Göttingen, Germany. It is a rotating full annular 1.5 stage turbine configuration which is coupled to a combustor simulator. The combustor simulator is designed to create turbine inlet conditions which are hydrodynamically representative for a lean-burn aero engine. A detailed description of the test rig and its instrumentation as well as a discussion of the measurement results is presented in part I of this paper. Part II focuses on numerical modeling of the test rig to further extend the understanding of the measurement results. Integrated simulations of the configuration including combustor simulator and nozzle guide vanes are performed for leading edge and passage clocking position and the effect on the hot streak migration is discussed. The simulation and experimental results at the combustor-turbine interface are compared showing a good overall agreement. The relevant flow features are correctly predicted in the simulations, proving the suitability of the numerical model for application to integrated combustor-turbine interaction analysis.

Sign in / Sign up

Export Citation Format

Share Document