Sensitization of the SST Turbulence Model to Rotation and Curvature by Applying the Spalart–Shur Correction Term

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Pavel E. Smirnov ◽  
Florian R. Menter
Keyword(s):  
Turbulent Flows ◽  
Turbulence Model ◽  
Transport Model ◽  
Correction Term ◽  
Computational Cost ◽  
Turbulence Models ◽  
Reynolds Stress Transport Model ◽  
Wide Range ◽  
Sst Model ◽  
The One

A rotation-curvature correction suggested earlier by Spalart and Shur (1997, “On the Sensitization of Turbulence Models to Rotation and Curvature,” Aerosp. Sci. Technol., 1(5), pp. 297–302) for the one-equation Spalart–Allmaras turbulence model is adapted to the shear stress transport model. This new version of the model (SST-CC) has been extensively tested on a wide range of both wall-bounded and free shear turbulent flows with system rotation and/or streamline curvature. Predictions of the SST-CC model are compared with available experimental and direct numerical simulations (DNS) data, on the one hand, and with the corresponding results of the original SST model and advanced Reynolds stress transport model (RSM), on the other hand. It is found that in terms of accuracy the proposed model significantly improves the original SST model and is quite competitive with the RSM, whereas its computational cost is significantly less than that of the RSM.

Sensitization of the SST Turbulence Model to Rotation and Curvature by Applying the Spalart-Shur Correction Term

2008 ◽  
Author(s):  
Pavel E. Smirnov ◽  
Florian R. Menter
Keyword(s):  
Turbulent Flows ◽  
Turbulence Model ◽  
Transport Model ◽  
Correction Term ◽  
Computational Cost ◽  
Reynolds Stresses ◽  
Wide Range ◽  
Sst Model ◽  
Shear Stress Transport Model ◽  
Sst Turbulence Model

A rotation-curvature correction suggested earlier by Spalart and Shur for the one-equation Spalart-Allmaras turbulence model is adapted to the Shear Stress Transport model. This new version of the model (SST-CC) has been extensively tested on a wide range of both wall-bounded and free shear turbulent flows with system rotation and/or streamline curvature. Predictions of the SST-CC model are compared with available experimental and DNS data, on one hand, and with the corresponding results of the original SST model and advanced Reynolds stresses transport model (RSM), on the other hand. It is found, that in terms of accuracy the proposed model significantly improves the original SST model and is quite competitive with the RSM, whereas its computational cost is significantly less than that of the RSM.

scholarly journals Analysis of Flow Characteristics and Effects of Turbulence Models for the Butterfly Valve

2021 ◽  
Vol 11 (14) ◽  
pp. 6319
Author(s):  
Sung-Woong Choi ◽  
Hyoung-Seock Seo ◽  
Han-Sang Kim
Keyword(s):  
Turbulence Model ◽  
Dissipation Rate ◽  
Flow Characteristics ◽  
Turbulence Models ◽  
Flow Properties ◽  
Nominal Diameter ◽  
Large Pressure ◽  
Sst Model ◽  
Turbulence Effect ◽  
Valve Opening

In the present study, the flow characteristics of butterfly valves with different sizes DN 80 (nominal diameter: 76.2 mm), DN 262 (nominal diameter: 254 mm), DN 400 (nominal diameter: 406 mm) were numerically investigated under different valve opening percentages. Representative two-equation turbulence models of two-equation k-epsilon model of Launder and Sharma, two-equation k-omega model of Wilcox, and two-equation k-omega SST model of Menter were selected. Flow characteristics of butterfly valves were examined to determine turbulence model effects. It was determined that increasing turbulence effect could cause many discrepancies between turbulence models, especially in areas with large pressure drop and velocity increase. In addition, sensitivity analysis of flow properties was conducted to determine the effect of constants used in each turbulence model. It was observed that the most sensitive flow properties were turbulence dissipation rate (Epsilon) for the k-epsilon turbulence model and turbulence specific dissipation rate (Omega) for the k-omega turbulence model.

Computational Fluid Dynamics Evaluation of Heat Transfer Correlations for Sodium Flows in a Heat Exchanger

2010 ◽  
Vol 132 (5) ◽  
Author(s):  
Seok-Ki Choi ◽  
Seong-O Kim ◽  
Hoon-Ki Choi
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Turbulence Model ◽  
Numerical Solutions ◽  
Numerical Study ◽  
Cross Flow ◽  
Turbulence Models ◽  
Parallel Flow ◽  
Sst Model ◽  
Heat Transfer Correlations

A numerical study for the evaluation of heat transfer correlations for sodium flows in a heat exchanger of a fast breeder nuclear reactor is performed. Three different types of flows such as parallel flow, cross flow, and two inclined flows are considered. Calculations are performed for these three typical flows in a heat exchanger changing turbulence models. The tested turbulence models are the shear stress transport (SST) model and the SSG-Reynolds stress turbulence model by Speziale, Sarkar, and Gaski (1991, “Modelling the Pressure-Strain Correlation of Turbulence: An Invariant Dynamical System Approach,” J. Fluid Mech., 227, pp. 245–272). The computational model for parallel flow is a flow past tubes inside a circular cylinder and those for the cross flow and inclined flows are flows past the perpendicular and inclined tube banks enclosed by a rectangular duct. The computational results show that the SST model produces the most reliable results that can distinguish the best heat transfer correlation from other correlations for the three different flows. It was also shown that the SSG-RSTM high-Reynolds number turbulence model does not deal with the low-Prandtl number effect properly when the Peclet number is small. According to the present calculations for a parallel flow, all the old correlations do not match with the present numerical solutions and a new correlation is proposed. The correlations by Dwyer (1966, “Recent Developments in Liquid-Metal Heat Transfer,” At. Energy Rev., 4, pp. 3–92) for a cross flow and its modified correlation that takes into account of flow inclination for inclined flows work best and are accurate enough to be used for the design of the heat exchanger.

Assessment of Certainty of Ventilation Processes Mathematical Modeling

2015 ◽  
Vol 725-726 ◽  
pp. 1255-1260
Author(s):  
Tamara Daciuk ◽  
Vera Ulyasheva
Keyword(s):  
Mathematical Modeling ◽  
Turbulent Flows ◽  
Turbulence Models ◽  
Field Measurements ◽  
Heat Emission ◽  
Emission Sources ◽  
Wide Range ◽  
Calculation Results ◽  
Definition Of ◽  
Semiempirical Models

Numerical experiment has been successfully used during recent 10-15 years to solve a wide range of thermal and hydrogasodynamic tasks. Application of mathematical modeling used to design the ventilation systems for production premises characterized by heat emission may be considered to be an effective method to obtain reasonable solutions. Results of calculation performed with numerical solution of ventilation tasks depend on turbulence model selection. Currently a large number of different turbulence models used to calculate turbulent flows are known. Testing and definition of applicability limits for semiempirical models of turbulence should be considered to be a preliminary stage of calculation. This article presents results of test calculations pertaining to thermal air process modeling in premises characterized by presence of heat emission sources performed with employment of different models of turbulence. Besides, analysis of calculation results and comparison with field measurements data are presented.

scholarly journals Assessment of CFD turbulence models for free surface flow simulation and 1-D modelling for water level calculations over a broad-crested weir floodway

Water SA ◽  
2019 ◽  
Vol 45 (3 July) ◽  
Author(s):  
Ahmed M Helmi
Keyword(s):  
Experimental Data ◽  
Free Surface ◽  
Water Level ◽  
Dimensional Analysis ◽  
Turbulence Model ◽  
Turbulence Models ◽  
Cfd Simulations ◽  
One Dimensional ◽  
The Mean ◽  
The One

Floodways, where a road embankment is permitted to be overtopped by flood water, are usually designed as broad-crested weirs. Determination of the water level above the floodway is crucial and related to road safety. Hydraulic performance of floodways can be assessed numerically using 1-D modelling or 3-D simulation using computational fluid dynamics (CFD) packages. Turbulence modelling is one of the key elements in CFD simulations. A wide variety of turbulence models are utilized in CFD packages; in order to identify the most relevant turbulence model for the case in question, 96 3-D CFD simulations were conducted using Flow-3D package, for 24 broad-crested weir configurations selected based on experimental data from a previous study. Four turbulence models (one-equation, k-ε, RNG k-ε, and k-ω) ere examined for each configuration. The volume of fluid (VOF) algorithm was adopted for free water surface determination. In addition, 24 1-D simulations using HEC-RAS-1-D were conducted for comparison with CFD results and experimental data. Validation of the simulated water free surface profiles versus the experimental measurements was carried out by the evaluation of the mean absolute error, the mean relative error percentage, and the root mean square error. It was concluded that the minimum error in simulating the full upstream to downstream free surface profile is achieved by using one-equation turbulence model with mixing length equal to 7% of the smallest domain dimension. Nevertheless, for the broad-crested weir upstream section, no significant difference in accuracy was found between all turbulence models and the one-dimensional analysis results, due to the low turbulence intensity at this part. For engineering design purposes, in which the water level is the main concern at the location of the flood way, the one-dimensional analysis has sufficient accuracy to determine the water level.

Modeling of Turbulent Flows Through the Annular Channel with Eccentricity and Rotating Inner Cilinder

2012 ◽  
Vol 7 (4) ◽  
pp. 79-86
Author(s):  
Evgeny Podryabinkin ◽  
Valeriy Rudyak
Keyword(s):  
Pressure Drop ◽  
Turbulent Flows ◽  
Transport Model ◽  
Reverse Flow ◽  
Axial Flow ◽  
Annular Channel ◽  
Rotational Flow ◽  
Concentric Annulus ◽  
Cylindrical Annulus ◽  
Wide Range

In this paper fully developed turbulent flows of Newtonian fluid in cylindrical annulus with eccentricity and rotating inner cylinder has been systematically studied. Modeling has been performed on the base of Menter Shear Transport model of turbulence in a wide range of Reynolds numbers, eccentricity, and radii ratio. As the result dependencies of flow field and pressure drop along the channel on geometrical and flow parameters have been found. It was shown that flow characteristics and dependence of the pressure drop are determined by which flow axial or rotational dominates and caused generation of turbulence. When rotational flow dominates the dependence of the pressure drop is almost linear. When axial flow dominates rotation practically has no impact on the pressure drop in concentric annulus. Appearance of the reverse flow in eccentric channel has a major impact on the pressure drop. In case when rotational flow dominates, appearance of the reverse flow is accompanied by threshold flow restructuring at some critical value of eccentricity. A correlation for determination of the pressure drop in various regimes has been developed for the case of concentric annulus

scholarly journals Hybrid Turbulence Models: Recent Progresses and Further Researches

2019 ◽  
Vol 130 ◽  
pp. 01013
Author(s):  
Hariyo Priambudi Setyo Pratomo ◽  
Fandi Dwiputra Suprianto ◽  
Teng Sutrisno
Keyword(s):  
Turbulent Flows ◽  
Turbulence Modeling ◽  
A Priori ◽  
Computational Cost ◽  
Turbulence Models ◽  
Turbulence Scale ◽  
Research Activities ◽  
Daunting Task ◽  
Active Research ◽  
Inherent Nature

Turbulence simulation remains one of the active research activities in computational engineering. Along with the increase in computing power and the prime motivation of improving the accuracy of statistical turbulence modeling approaches and reducing the expensive computational cost of both direct numerical and large turbulence scale- resolving simulations, various hybrid turbulence models being capable of capturing unsteadiness in the turbulence are now accessible. Nevertheless this introduces the daunting task to select an appropriate method for different cases as one can not know a priori the inherent nature of the turbulence. It is the aim of this paper to address recent progresses and further researches within a branch of the hybrid RANS-LES models examined by the first author as simple test cases but generating complex turbulent flows are available from experimentation. In particular, failure of a seamless hybrid formulation not explicitly dependent on the grid scale is discussed. From the literature, it is practical that at least one can go on with confidence when choosing a potential hybrid model by intuitively distinguishing between strongly and weakly unstable turbulent flows.

Modification of Shear Stress Transport Turbulence Model Using Helicity for Predicting Corner Separation Flow in a Linear Compressor Cascade

2020 ◽  
Vol 142 (2) ◽  
Author(s):  
Yangwei Liu ◽  
Yumeng Tang ◽  
Ashley D. Scillitoe ◽  
Paul G. Tucker
Keyword(s):  
Shear Stress ◽  
Turbulence Model ◽  
Incidence Angle ◽  
Computational Cost ◽  
Separation Flow ◽  
Compressor Cascade ◽  
Production Term ◽  
Corner Separation ◽  
Shear Stress Transport ◽  
Sst Model

Abstract Three-dimensional corner separation significantly affects compressor performance, but turbulence models struggle to predict it accurately. This paper assesses the capability of the original shear stress transport (SST) turbulence model to predict the corner separation in a linear highly loaded prescribed velocity distribution (PVD) compressor cascade. Modifications for streamline curvature, Menter’s production limiter, and the Kato-Launder production term are examined. Comparisons with experimental data show that the original SST model and the SST model with different modifications can predict the corner flow well at an incidence angle of −7 deg, where the corner separation is small. However, all the models overpredict the extent of the flow separation when the corner separation is larger, at an incidence angle of 0 deg. The SST model is then modified using the helicity to take account of the energy backscatter, which previous studies have shown to be important in the corner separation regions of compressors. A Reynolds stress model (RSM) is also used for comparison. By comparing the numerical results with experiments and RSM results, it can be concluded that sensitizing the SST model to helicity can greatly improve the predictive accuracy for simulating the corner separation flow. The accuracy is quite competitive with the RSM, whereas in terms of computational cost and robustness it is superior to the RSM.

scholarly journals A Second-Order Turbulence Model Based on a Reynolds Stress Approach for Two-Phase Flow—Part I: Adiabatic Cases

2009 ◽  
Vol 2009 ◽  
pp. 1-14 ◽  
Author(s):  
S. Mimouni ◽  
F. Archambeau ◽  
M. Boucker ◽  
J. Laviéville ◽  
C. Morel
Keyword(s):  
Liquid Phase ◽  
Reynolds Stress ◽  
Turbulence Model ◽  
Two Phase Flow ◽  
Turbulence Modeling ◽  
Transport Model ◽  
Phase Flow ◽  
Two Phase ◽  
Model Based ◽  
Reynolds Stress Transport Model

In our work in 2008, we evaluated the aptitude of the code Neptune_CFD to reproduce the incidence of a structure topped by vanes on a boiling layer, within the framework of the Neptune project. The objective was to reproduce the main effects of the spacer grids. The turbulence of the liquid phase was modeled by a first-orderK-εmodel. We show in this paper that this model is unable to describe the turbulence of rotating flows, in accordance with the theory. The objective of this paper is to improve the turbulence modeling of the liquid phase by a second turbulence model based on aRij-εapproach. Results obtained on typical single-phase cases highlight the improvement of the prediction for all computed values. We tested the turbulence modelRij-εimplemented in the code versus typical adiabatic two-phase flow experiments. We check that the simulations with the Reynolds stress transport model (RSTM) give satisfactory results in a simple geometry as compared to aK-εmodel: this point is crucial before calculating rod bundle geometries where theK-εmodel may fail.

Numerical Benchmark of Turbulence Modeling in Gas Turbine Rotor-Stator System

2010 ◽  
Author(s):  
Riccardo Da Soghe ◽  
Luca Innocenti ◽  
Antonio Andreini ◽  
Se´bastien Poncet
Keyword(s):  
Gas Turbine ◽  
Boundary Layers ◽  
Correction Term ◽  
Computational Cost ◽  
Turbulence Models ◽  
Turbine Rotor ◽  
Operating Conditions ◽  
Curvature Effects ◽  
Low Reynolds ◽  
Secondary Air

Accurate design of the secondary air system is one of the main tasks for reliability and performance of gas turbine engines. The selection of a suitable turbulence model for the study of rotor-stator cavity flows, which remains an open issue in the literature, is here addressed for several operating conditions. A numerical benchmark of turbulence models is indeed proposed in the case of rotor-stator disk flows with and without superimposed throughflow. The predictions obtained by the means of several two equation turbulence models available within the CFD solver Ansys CFX 12.0 are compared with those previously evaluated by Poncet et al. (1; 2) through the Reynolds Stress Model (RSM) of Elena and Schiestel (3; 4) implemented in a proprietary finite volume code. The standard k-ε and k-ω SST models including high and low Reynolds approaches, have been used for all calculations presented here. Furthermore, some tests were performed using the innovative k-ω SST-CC and k-ω SST-RM models that take into account the curvature effects via the Spalart-Shur correction term (5) and the reattachement modification proposed by Menter (6) respectively. The numerical calculations have been compared to extensive velocity and pressure measurements performed on the test rig of the IRPHE’s laboratory in Marseilles (1; 2). Several configurations, covering a large range of real engine operating conditions, were considered. The influence of the typical non dimensional flow parameters (Reynolds number and flowrate coefficient) on the flow structure is studied in detail. In the case of an enclosed cavity, the flow exhibits a Batchelor-like structure with two turbulent boundary layers separated by a laminar rotating core. When an inward axial throughflow is superimposed, the flow remains of Batchelor type with a core rotating faster than the disk because of conservation of the angular momentum. In this case, turbulence intensities are mainly confined close to the stator. Turbulence models based on a low Reynolds approach provide better overall results for the mean and turbulent fields especially within the very thin boundary layers. The standard k-ω SST model offers the best trade-off between accuracy and computational cost for the parameters considered here. In the case of an outward throughflow, the k-ω SST in conjunction with a low Reynolds approach and RSM models provide similar results and predict quite well the transition from the Batchelor to the Stewartson structures.

Sign in / Sign up

Export Citation Format

Share Document