Review—Axial Compressor Stall Phenomena

1980 ◽  
Vol 102 (2) ◽  
pp. 134-151 ◽  
Author(s):  
E. M. Greitzer
Keyword(s):  
Fluid Dynamic ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Empirical Correlations ◽  
Flow Distortion ◽  
Stall Margin ◽  
Compression System ◽  
Casing Treatment ◽  
Linearized Stability ◽  
Compressor Performance

Stall in compressors can be associated with the initiation of several types of fluid dynamic instabilities. These instabilities and the different phenomena, surge and rotating stall, which result from them, are discussed in this paper. Assessment is made of the various methods of predicting the onset of compressor and/or compression system instability, such as empirical correlations, linearized stability analyses, and numerical unsteady flow calculation procedures. Factors which affect the compressor stall point, in particular inlet flow distortion, are reviewed, and the techniques which are used to predict the loss in stall margin due to these factors are described. The influence of rotor casing treatment (grooves) on increasing compressor flow range is examined. Compressor and compression system behavior subsequent to the onset of stall is surveyed, with particular reference to the problem of engine recovery from a stalled condition. The distinction between surge and rotating stall is emphasized because of the very different consequences on recoverability. The structure of the compressor flow field during rotating stall is examined, and the prediction of compressor performance in rotating stall, including stall/unstall hysteresis, is described.

scholarly journals Numerical Optimization of a Stall Margin Enhancing Recirculation Channel for an Axial Compressor

Fluids ◽  
2019 ◽  
Vol 4 (2) ◽  
pp. 88
Author(s):  
Motoyuki Kawase ◽  
Aldo Rona
Keyword(s):  
High Speed ◽  
High Performance ◽  
Fluid Dynamic ◽  
Axial Compressor ◽  
Leading Edge ◽  
Navier Stokes ◽  
Test Case ◽  
Dynamic Simulations ◽  
Stall Margin ◽  
Casing Treatment

A proof of concept is provided by computational fluid dynamic simulations of a new recirculating type casing treatment. This treatment aims at extending the stable operating range of highly loaded axial compressors, so to improve the safety of sorties of high-speed, high-performance aircraft powered by high specific thrust engines. This casing treatment, featuring an axisymmetric recirculation channel, is evaluated on the NASA rotor 37 test case by steady and unsteady Reynolds Averaged Navier Stokes (RANS) simulations, using the realizable k-ε model. Flow blockage at the recirculation channel outlet was mitigated by chamfering the exit of the recirculation channel inner wall. The channel axial location from the rotor blade tip leading edge was optimized parametrically over the range −4.6% to 47.6% of the rotor tip axial chord c z . Locating the channel at 18.2% c z provided the best stall margin gain of approximately 5.5% compared to the untreated rotor. No rotor adiabatic efficiency was lost by the application of this casing treatment. The investigation into the flow structure with the recirculating channel gave a good insight into how the new casing treatment generates this benefit. The combination of stall margin gain at no rotor adiabatic efficiency loss makes this design attractive for applications to high-speed gas turbine engines.

Aeroelastic aspects of Axial Compressor Stage with Self-Recirculating Casing Treatment

2021 ◽  
pp. 1-34
Author(s):  
S Satish Kumar ◽  
Dilipkumar Bhanudasji Alone ◽  
Shobhavathy Thimmaiah ◽  
J Rami Reddy Mudipalli ◽  
Lakshya Kumar ◽  
...  
Keyword(s):  
Flow Condition ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Successful Implementation ◽  
Compressor Stage ◽  
Stall Margin ◽  
Casing Treatment ◽  
Compressor Rotor ◽  
Forcing Function ◽  
Treatment Designs

Abstract For successful implementation of casing treatment designs in axial compressors, apart from the stall margin improvement benefits, aeroelasticity also plays a major role. This manuscript addresses the not often discussed aeroelastic aspects of a new discrete type of passive Self-Recirculating Casing Treatment (RCT) designed for a transonic axial compressor stage. Experiments are carefully designed for synchronized measurement of the unsteady fluidic disturbances and vibrations during rotating stall for compressor with baseline solid casing and Self-RCT. The modal characteristics of the axial compressor rotor-disk assembly are studied experimentally and numerically. Experimentally it is observed that the rotating stall cells excite the blades in their fundamental mode in a compressor with baseline solid casing at the stall flow condition. In contrast, there is no excitation of the blades in the compressor with self-recirculating casing treatment at the same solid casing stall flow condition. Also, the self-recirculating casing treatment compared to the solid casing can significantly reduce the overall vibration levels of the blades that are excited at the stall flow condition. The casing treatment is able to alter the flow field near the tip region of the rotor blade, and hence influencing the forcing function of the rotating cantilever blades to have the aeroelastic benefit.

Effects of Blade Damage on the Performance of a Transonic Axial Compressor Rotor

2012 ◽  
Author(s):  
Yanling Li ◽  
Abdulnaser Sayma
Keyword(s):  
Axial Compressor ◽  
Rotating Stall ◽  
Rotor Blades ◽  
Design Stage ◽  
Compressor Blades ◽  
Stall Margin ◽  
Compressor Rotor ◽  
Surge Margin ◽  
Compressor Performance ◽  
Transonic Axial Compressor

Gas turbine axial compressor blades may encounter damage during service for various reasons. Debris from casing or foreign objects may impact blades causing damage near the rotor’s tip. This may result in deterioration of performance and reduction in the surge margin. Ability to assess the effect of damaged blades on the compressor performance and stability is important at both the design stage and in service. The damage to compressor blades breaks the cyclic symmetry of the compressor assembly. Thus computations have to be performed using the whole annulus. Moreover, if rotating stall or surge occurs, the downstream boundary conditions are not known and simulations become difficult. This paper presents an unsteady CFD analysis of compressor performance with tip curl damage. Tip curl damage typically occurs when rotor blades hit a loose casing liner. The computations were performed up to the stall boundary, predicting rotating stall patterns. The aim is to assess the effect of blade damage on stall margin and provide better understanding of the flow behaviour during rotating stall. Computations for the undamaged rotor are also performed for comparison. A transonic axial compressor rotor is used for the time-accurate numerical unsteady flow simulations, with a variable choked nozzle downstream simulating an experimental throttle. One damaged blade was introduced in the rotor assembly and computations were performed at 60% of the design rotational speed. It was found that there is no significant effect on the compressor stall margin due to one damaged blade despite the differences in rotating stall patterns between the undamaged and damaged assemblies.

scholarly journals Surge prevention in gas turbines: an overview over historical solutions and perspectives about the future

2019 ◽  
Vol 113 ◽  
pp. 02003
Author(s):  
Carlo Alberto Niccolini Marmont Du Haut Champ ◽  
Aristide Fausto Massardo ◽  
Mario Luigi Ferrari ◽  
Paolo Silvestri
Keyword(s):  
Gas Turbines ◽  
Reverse Flow ◽  
Fluid Dynamic ◽  
Experimental Studies ◽  
Axial Compressor ◽  
Energy System ◽  
Rotating Stall ◽  
Lumped Parameter Model ◽  
Compression System ◽  
Working Zone

The aim of the present work is to retrace experimental, analytical and numerical analyses which deal with compressor instability phenomena, such as rotating stall and surge. While the first affects only the machine itself, the second involves the whole energy system. Surge onset is characterized by strong pressure and mass flow rate fluctuations which can even lead to reverse flow through the compressor. Experimental studies on prevention of axial compressor fluid dynamic instabilities, which can be propagated and eventually damage the solid structure, have been carried out by many authors. The first important studies on this topic tried to underline the main aspects of the complex detailed mechanism of surge, by replacing the compression system with an equivalent conceptual lumped parameter model. This is specially meant to capture the unsteady behaviour and the transient response of the compression system itself, particularly its dependence on variations in the volume of discharge downstream and in the settings of the throttle valve at its outlet (which simulates the actual load coupled to the compressor). Greitzer’s model is still regarded as the milestone for new investigations about active control and stabilization of surge and, more generally, about active suppression of aerodynamic instabilities in turbomachinery. During the last years, a lot of simulations and experimental studies about surge have been conducted on multistage centrifugal compressors with different architectures (e.g. equipped with vaneless or vaned diffusers). Moreover, further kinds of analysis try to extend the stable working zone of compressors, identifying stall and surge precursors extractable from information contained in the vibro-acoustical and rotodynamic response of the system.

scholarly journals Effects of Endwall Suction and Blowing on Compressor Stability Enhancement

1989 ◽  
Author(s):  
N. K. W. Lee ◽  
E. M. Greitzer
Keyword(s):  
Flow Injection ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Primary Objective ◽  
Stall Margin ◽  
Casing Treatment ◽  
Blade Row ◽  
Stall Margin Improvement ◽  
Stability Enhancement ◽  
Suction And Blowing

An experimental investigation was carried out to examine the effects on stall margin of flow injection into, and flow removal out of, the endwall region of an axial compressor blade row. A primary objective of the investigation was clarification of the mechanism by which casing treatment (which involves both removal and injection) suppresses stall in turbomachines. To simulate the relative motion between blade and treatment, the injection and removal took place through a slotted hub rotating beneath a cantilevered stator row. Overall performance data and detailed (time-averaged) flowfield measurements were obtained. Flow injection and removal both increased the stalling pressure rise, but neither was as effective as the wall treatment. Removal of high blockage flow is thus not the sole reason for the observed stall margin improvement in casing or hub treatment, as injection can also contribute significantly to stall suppression. The results also indicate that the increase in stall pressure rise with injection is linked to the streamwise momentum of the injected flow, and it is suggested that this should be the focus of further studies.

Stall Warning Using the Rotor Tip Pressure in a Transonic Axial Compressor With Circumferential Grooves

2018 ◽  
Author(s):  
Byeung Jun Lim ◽  
Tae Choon Park ◽  
Young Seok Kang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Single Stage ◽  
Stall Inception ◽  
Casing Treatment ◽  
Stall Warning ◽  
Transonic Axial Compressor

In this study, characteristics of stall inception in a single-stage transonic axial compressor with circumferential grooves casing treatment were investigated experimentally. Additionally, the characteristic of increasing irregularity in the pressure inside circumferential grooves as the compressor approaches the stall limit was applied to the stall warning method. Spike-type rotating stall was observed in the single-stage transonic axial compressor with smooth casing. When circumferential grooves were applied, the stall inception was suppressed and the operating point of the compressor moved to lower flow rate than the stall limit. A spike-like disturbance was developed into a rotating stall cell and then the Helmholtz perturbation was overlapped on it at N = 80%. At N = 70 %, the Helmholtz perturbation was observed first and the amplitude of the wave gradually increased as mass flow rate decreased. At N = 60%, spike type stall inceptions were observed intermittently and then developed into continuous rotating stall at lower mass flow rate. Pressure measured at the bottom of circumferential grooves showed that the level of irregularity of pressure increased as flow rate decreased. Based on the characteristic of increasing irregularity of the pressure signals inside the circumferential grooves as stall approaches, an autocorrelation technique was applied to the stall warning. This technique could be used to provide warning against stall and estimate real-time stall margins in compressors with casing treatments.

Improving a one-dimensional centrifugal compressor performance prediction method

2005 ◽  
Vol 219 (8) ◽  
pp. 653-659 ◽  
Author(s):  
E Swain
Keyword(s):  
Centrifugal Compressor ◽  
Performance Prediction ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Prediction Method ◽  
Compressor Cascade ◽  
One Dimensional ◽  
Compressor Performance ◽  
Cfd Analyses

A one-dimensional centrifugal compressor performance prediction technique that has been available for some time is updated as a result of extracting the component performance from three-dimensional computational fluid dynamic (CFD) analyses. Confidence in the CFD results is provided by comparison of overall performance for one of the compressor examples. The extracted impeller characteristic is compared with the original impeller loss model, and this indicated that some improvement was desirable. The position of least impeller loss was determined using a traditional axial compressor cascade method, and suitable algebraic expressions were derived to match the CFD data. The merit of the approach lies with the relative ease that CFD component performance currently can be achieved and adjusting one-dimensional methods to agree with the CFD-derived models.

Influencing Parameters of Tip Blowing Interacting With Rotor Tip Flow

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Cyril Guinet ◽  
André Inzenhofer ◽  
Volker Gümmer
Keyword(s):  
Geometric Model ◽  
Axial Compressor ◽  
Axial Flow ◽  
Navier Stokes ◽  
Axial Position ◽  
Design Parameters ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Casing Treatments

The design space of axial-flow compressors is restricted by stability issues. Different axial-type casing treatments (CTs) have shown their ability to enhance compressor stability and to influence efficiency. Casing treatments have proven to be effective, but there still is need for more detailed investigations and gain of understanding for the underlying flow mechanism. Casing treatments are known to have a multitude of effects on the near-casing 3D flow field. For transonic compressor rotors, these are more complex, as super- and subsonic flow regions alternate while interacting with the casing treatment. To derive design rules, it is important to quantify the influence of the casing treatment on the different tip flow phenomena. Designing a casing treatment in a way that it antagonizes only the deteriorating secondary flow effects can be seen as a method to enhance stability while increasing efficiency. The numerical studies are carried out on a tip-critical rotor of a 1.5-stage transonic axial compressor. The examined recirculating tip blowing casing treatment (TBCT) consists of a recirculating channel with an air off-take above the rotor and an injection nozzle in front of the rotor. The design and functioning of the casing treatment are influenced by various parameters. A variation of the geometry of the tip blowing, more specifically the nozzle aspect ratio, the axial position, or the tangential orientation of the injection port, was carried out to identify key levers. The tip blowing casing treatment is defined as a parameterized geometric model and is automatically meshed. A sensitivity analysis of the respective design parameters of the tip blowing is carried out on a single rotor row. Their impact on overall efficiency and their ability to improve stall margin are evaluated. The study is carried out using unsteady Reynolds-averaged Navier–Stokes (URANS) simulations.

Extensive Experimental Study of Circumferential Single Groove in an Axial Flow Compressor

2014 ◽  
Author(s):  
Jichao Li ◽  
Feng Lin ◽  
Sichen Wang ◽  
Juan Du ◽  
Chaoqun Nie ◽  
...  
Keyword(s):  
Experimental Study ◽  
Unsteady Flow ◽  
Axial Compressor ◽  
Axial Flow ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Good Tool ◽  
Stall Margin ◽  
Casing Treatment ◽  
Tip Leakage

Circumferential single-groove casing treatment becomes an interesting topic in recent few years, because it is a good tool to explore the interaction between the groove and the flow in blade tip region. The stall margin improvement (SMI) as a function of the axial groove location has been found for some compressors, such a trend cannot be predicted by steady high-fidelity CFD simulations. Recent efforts show that to catch such a trend, multi-passage, unsteady flow simulations are needed as the stalling mechanism itself involves cross-passage flows and unsteady dynamics. This indicates a need to validate unsteady numerical simulation results. In this paper, an extensive experimental study of a total of fifteen single casing grooves in a low-speed axial compressor rotor is presented, the groove location varies from 0.4% to 98.3% of axial tip chord are tested. The unsteady pressure data both at casing and at the blade wake with different groove locations are measured and processed, including the movement of trajectory of tip leakage flow, the evolution of unsteadiness of tip leakage flow (UTLF), the unsteady spectrum signature during the stall process, and the outlet unsteady flow characteristic along the span. These data provide a case study for validation of the unsteady CFD results, and may be helpful for further interpretation on the stalling mechanism affected by circumferential casing grooves.

Numerical Investigation on the Effect of Bleed Port With Self-Recirculating Casing Treatment on the Stability of a 1.5-Stage Transonic Compressor

2019 ◽  
Author(s):  
Yiming Zhong ◽  
WuLi Chu ◽  
HaoGuang Zhang
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Stability Margin ◽  
Axial Position ◽  
Stable Operation ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Compressor Efficiency

Abstract Compared to the traditional casing treatment, the self-recirculating casing treatment (SCT) can improve or not decrease the compressor efficiency while achieving the stall margin improvement. For the bleed port, the main design indicator is to reduce the flow loss caused by suction, while providing sufficient jet flow and jet pressure to the injector. In order to gain a better study of the bleed port stabilization mechanisms, the bleed configuration was parameterized with the bleed port inlet width and the bleed port axial position. Five kinds of recirculating casing treatments were applied to a 1.5-stage transonic axial compressor with the method of three-dimensional unsteady numerical simulation. Fifteen identical self-recirculating devices are uniformly mounted around the annulus. The numerical results show that the SCT can improve compressor total pressure ratio and stability, shift the stall margin towards lower mass flows. Furthermore, it has no impact on compressor efficiency. The optimal case presents that stability margin is improved by 6.7% employing 3.1% of the annulus mass flow. Expanding bleed port inlet width to an intermediate level can further enhance compressor stability, but excessive bleed port inlet width will reduce the stabilization effect. The optimal bleed port position is located in the blocked area of the low energy group at the top of the rotor. In the case of solid casing, stall inception was the tip blockage, which was mainly triggered by the interaction of the tip leakage vortex and passage shock. From radial distribution, the casing treatment predominantly affects the above 70% span. The reduction of tip reflux region by suction effect is the main reason for the extension of stable operation range. The SCT also has an obvious stability improvement in tip blockage stall, while delaying the occurrence of compressor stall.

Sign in / Sign up

Export Citation Format

Share Document