Experimental Measurement of the Dynamic Force Response of a Squeeze-Film Bearing Damper

1975 ◽  
Vol 97 (4) ◽  
pp. 1282-1290 ◽  
Author(s):  
John M. Vance ◽  
Alan J. Kirton
Keyword(s):  
Pressure Distribution ◽  
Taylor Vortex ◽  
Squeeze Film ◽  
Dynamic Force ◽  
Force Response ◽  
Cyclic Flow ◽  
Pressure Distributions ◽  
Taylor Vortex Flow ◽  
Force Components ◽  
Annular Clearance

An experimental study of the hydrodynamic force response of a squeeze-film bearing damper with end seals was carried out. Measurements of the pressure distribution about a journal constrained to move in a circular orbit were made for the journal orbit centered in the annular clearance and offset from the center of the annular clearance. The effects of cyclic flow in a radial inlet were studied for the case of the journal orbit centered in the annular clearance. For the off-center case the pressure distribution around the damper was measured for four different combinations of eccentricity, radial velocity, and angular velocity of the line of centers, chosen in such a way as to allow calculation of the four bearing coefficients defined by Tondl. The experimentally determined pressure distributions were numerically integrated to determine the force components of the squeeze film. The results are compared to the “long bearing” and the “short bearing” solutions of Reynolds’ equation. For the centered case, good agreement was found with the shape of the “long bearing” solution. Higher-than-predicted pressures and forces for light viscosity oil are explained by showing that this case is operating in the Taylor vortex flow regime. Similar calculations indicate that turbine dampers can also operate with vortex or turbulent flow.

Investigation of Squeeze Film Damper Forces Produced by Circular Centered Orbits

1978 ◽  
Vol 100 (1) ◽  
pp. 15-21 ◽  
Author(s):  
E. Feder ◽  
P. N. Bansal ◽  
A. Blanco
Keyword(s):  
Aircraft Engine ◽  
Analytical Investigation ◽  
Operating Conditions ◽  
Squeeze Film ◽  
Oil Viscosity ◽  
Pressure Transducers ◽  
Pressure Distributions ◽  
Pressure Profiles ◽  
Force Components ◽  
Type Pressure

This paper presents the results of an experimental and analytical investigation of the dynamic forces generated by a squeeze film bearing damper constrained to move in circular centered orbits. These orbits were mechanically produced in a specially designed, end sealed, test rig. Aircraft engine damper geometry and operating conditions were simulated. The effect of journal speed, oil viscosity, inlet pressure, and eccentricity ratio on the damper performance was studied. The pressure distributions about the journal were measured for each test condition by high-response diaphragm-type pressure transducers. These pressure profiles were numerically integrated to determine the force components of the squeeze film. Experimental results were compared to an analysis which is summarized in this paper and included the effects of inlet and cavitation pressures. The “long bearing theory” was found to be reasonably accurate in predicting the shape and magnitude of the pressure distribution. Considerable emphasis was directed to the study of the circumferential pressure distributions between 180 deg and 360 deg since aircraft engine dampers generally operate in this region. For the cavitated film (i.e., pressure distributions less than 360 deg), accurate prediction of the damper forces was found to be critically dependent on the effect of inlet and cavitation pressures.

Effect of a Circumferential Feeding Groove on the Dynamic Force Response of a Short Squeeze Film Damper

1994 ◽  
Vol 116 (2) ◽  
pp. 369-376 ◽  
Author(s):  
G. L. Arauz ◽  
L. San Andres
Keyword(s):  
Flow Model ◽  
Dynamic Pressure ◽  
Squeeze Film ◽  
Dynamic Force ◽  
Force Response ◽  
Squeeze Film Damper ◽  
Circumferential Groove ◽  
Damping Characteristics ◽  
Radial Forces ◽  
Lubricant Viscosity

The effect of a circumferential feeding groove on the dynamic force response of a short length, open end squeeze film damper is studied experimentally. Damper configurations with increasing groove depths and journal orbit radii were tested for several conditions of whirl frequency and lubricant viscosity. Significant levels of dynamic pressure were measured at the circumferential groove, and relatively large tangential (damping) forces are produced at the groove which contribute considerably to the damping characteristics of the SFD test articles. Radial forces of substantial magnitude are determined at the groove and at the thin film land where the squeeze film Reynolds number is typically less than 1. The circumferential groove is thought to induce an inertia like effect into the film land. The experimental results correlate well with the predictions from a groove volume-circumferential flow model developed.

Experimental Study on the Effect of a Circumferential Feeding Groove on the Dynamic Force Response of a Sealed Squeeze Film Damper

1996 ◽  
Vol 118 (4) ◽  
pp. 900-905 ◽  
Author(s):  
G. L. Arauz ◽  
Luis San Andres
Keyword(s):  
Piston Ring ◽  
Dynamic Pressure ◽  
Squeeze Film ◽  
Dynamic Force ◽  
Force Response ◽  
Flow Conditions ◽  
Squeeze Film Damper ◽  
Circumferential Groove ◽  
Damping Characteristics ◽  
Radial Forces

The influence of a circumferential feeding groove on the dynamic force response of a sealed squeeze film damper is determined experimentally. The damper is sealed by means of a serrated piston ring located at the discharge end of the damper. Damper configurations with two different groove depths and journal orbit radii were tested at increasing whirl frequencies. Large levels of dynamic pressure were measured at the circumferential groove, and relatively large tangential (damping) forces are produced at the groove which contribute considerably to the damping characteristics of the test damper. Radial forces were also determined at the feeding groove and at the film land for uncavitated flow conditions.

scholarly journals Effect of Pressure Distribution on the Energy Dissipation of Lap Joints under Equal Pre-tension Force

Open Physics ◽  
2019 ◽  
Vol 17 (1) ◽  
pp. 320-328
Author(s):  
Delin Sun ◽  
Minggao Zhu
Keyword(s):  
Energy Dissipation ◽  
Pressure Distribution ◽  
Theoretical Basis ◽  
Lap Joints ◽  
Power Exponent ◽  
Lap Joint ◽  
Stick Slip ◽  
Pressure Distributions ◽  
Hysteretic Characteristics ◽  
Effective Use

Abstract In this paper, the energy dissipation in a bolted lap joint is studied using a continuum microslip model. Five contact pressure distributions compliant with the power law are considered, and all of them have equal pretension forces. The effects of different pressure distributions on the interface stick-slip transitions and hysteretic characteristics are presented. The calculation formulation of the energy dissipation is introduced. The energy dissipation results are plotted on linear and log-log coordinates to investigate the effect of the pressure distribution on the energy distribution. It is shown that the energy dissipations of the lap joints are related to the minimum pressure in the overlapped area, the size of the contact area and the value of the power exponent. The work provides a theoretical basis for further effective use of the joint energy dissipation.

scholarly journals Dynamic flight load measurements with MEMS pressure sensors

2021 ◽  
Author(s):  
Christian Raab ◽  
Kai Rohde-Brandenburger
Keyword(s):  
Pressure Distribution ◽  
Pressure Sensors ◽  
Flow Characteristics ◽  
Flight Test ◽  
Measurement Technology ◽  
Test Program ◽  
Aerodynamic Pressure ◽  
Pressure Distributions ◽  
Time Histories ◽  
Mems Pressure Sensors

AbstractThe determination of structural loads plays an important role in the certification process of new aircraft. Strain gauges are usually used to measure and monitor the structural loads encountered during the flight test program. However, a time-consuming wiring and calibration process is required to determine the forces and moments from the measured strains. Sensors based on MEMS provide an alternative way to determine loads from the measured aerodynamic pressure distribution around the structural component. Flight tests were performed with a research glider aircraft to investigate the flight loads determined with the strain based and the pressure based measurement technology. A wing glove equipped with 64 MEMS pressure sensors was developed for measuring the pressure distribution around a selected wing section. The wing shear force determined with both load determination methods were compared to each other. Several flight maneuvers with varying loads were performed during the flight test program. This paper concentrates on the evaluation of dynamic flight maneuvers including Stalls and Pull-Up Push-Over maneuvers. The effects of changes in the aerodynamic flow characteristics during the maneuver could be detected directly with the pressure sensors based on MEMS. Time histories of the measured pressure distributions and the wing shear forces are presented and discussed.

scholarly journals Influence of the Spatial Pressure Distribution of Breaking Wave Loading on the Dynamic Response of Wolf Rock Lighthouse

2021 ◽  
Vol 9 (1) ◽  
pp. 55
Author(s):  
Darshana T. Dassanayake ◽  
Alessandro Antonini ◽  
Athanasios Pappas ◽  
Alison Raby ◽  
James Mark William Brownjohn ◽  
...  
Keyword(s):  
Dynamic Response ◽  
Pressure Distribution ◽  
Distinct Element ◽  
Breaking Waves ◽  
Breaking Wave ◽  
Wave Loading ◽  
Wave Impact ◽  
Pressure Distributions ◽  
Impact Area ◽  
The Impact

The survivability analysis of offshore rock lighthouses requires several assumptions of the pressure distribution due to the breaking wave loading (Raby et al. (2019), Antonini et al. (2019). Due to the peculiar bathymetries and topographies of rock pinnacles, there is no dedicated formula to properly quantify the loads induced by the breaking waves on offshore rock lighthouses. Wienke’s formula (Wienke and Oumeraci (2005) was used in this study to estimate the loads, even though it was not derived for breaking waves on offshore rock lighthouses, but rather for the breaking wave loading on offshore monopiles. However, a thorough sensitivity analysis of the effects of the assumed pressure distribution has never been performed. In this paper, by means of the Wolf Rock lighthouse distinct element model, we quantified the influence of the pressure distributions on the dynamic response of the lighthouse structure. Different pressure distributions were tested, while keeping the initial wave impact area and pressure integrated force unchanged, in order to quantify the effect of different pressure distribution patterns. The pressure distributions considered in this paper showed subtle differences in the overall dynamic structure responses; however, pressure distribution #3, based on published experimental data such as Tanimoto et al. (1986) and Zhou et al. (1991) gave the largest displacements. This scenario has a triangular pressure distribution with a peak at the centroid of the impact area, which then linearly decreases to zero at the top and bottom boundaries of the impact area. The azimuthal horizontal distribution was adopted from Wienke and Oumeraci’s work (2005). The main findings of this study will be of interest not only for the assessment of rock lighthouses but also for all the cylindrical structures built on rock pinnacles or rocky coastlines (with steep foreshore slopes) and exposed to harsh breaking wave loading.

Development and Effects of Super-Critical Taylor-Vortex Flow in a Lightly Loaded Journal Bearing

1974 ◽  
Vol 96 (1) ◽  
pp. 28-35 ◽  
Author(s):  
R. C. DiPrima ◽  
J. T. Stuart
Keyword(s):  
Vortex Flow ◽  
Axial Direction ◽  
Basic Flow ◽  
Circular Cylinders ◽  
Taylor Vortex ◽  
Taylor Vortices ◽  
Taylor Vortex Flow ◽  
Secondary Motion ◽  
The Stability ◽  
Unified Description

At sufficiently high operating speeds in lightly loaded journal bearings the basic laminar flow will be unstable. The instability leads to a new steady secondary motion of ring vortices around the cylinders with a regular periodicity in the axial direction and a strength that depends on the azimuthial position (Taylor vortices). Very recently published work on the basic flow and the stability of the basic flow between eccentric circular cylinders with the inner cylinder rotating is summarized so as to provide a unified description. A procedure for calculating the Taylor-vortex flow is developed, a comparison with observed properties of the flow field is made, and formulas for the load and torque are given.

Sign in / Sign up

Export Citation Format

Share Document