Wind Speed Dependency of Low-Frequency Vibration Levels in Full-Scale Wind Turbines

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Xavier Escaler ◽  
Toufik Mebarki
Keyword(s):  
Wind Speed ◽  
Wind Turbines ◽  
High Speed ◽  
Wind Farm ◽  
Low Frequency ◽  
Average Frequency ◽  
Operating Conditions ◽  
Positive Slope ◽  
Low Frequency Vibration ◽  
Linear Fit

A series of continuous vibration measurements in 14 upwind wind turbines of the same model and belonging to the same wind farm have been conducted. The data were acquired over a period lasting approximately half a year. The tower axial vibration acceleration has been monitored in the frequency band from 0 to 10 Hz with an accelerometer mounted on the gearbox casing between the intermediate and the high-speed shafts. It has been observed that the average frequency spectrum is dominated by the blade passing frequency in all the wind turbines. The evolution of the vibration magnitudes over the entire range of operating conditions is also very similar for all the wind turbines. The root-mean-square (rms) acceleration value has been correlated with the wind speed, and it has been found that a linear fit with a positive slope is a useful model for prediction purposes.

scholarly journals Performance Enhancement of Proposed Namaacha Wind Farm by Minimising Losses Due to the Wake Effect: A Mozambican Case Study

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4291
Author(s):  
Paxis Marques João Roque ◽  
Shyama Pada Chowdhury ◽  
Zhongjie Huan
Keyword(s):  
Wind Speed ◽  
Wind Power ◽  
Wind Turbines ◽  
Power Output ◽  
Wind Farm ◽  
Wind Farms ◽  
Operating Conditions ◽  
Wake Effect ◽  
Wind Generators ◽  
Wind Potential

District of Namaacha in Maputo Province of Mozambique presents a high wind potential, with an average wind speed of around 7.5 m/s and huge open fields that are favourable to the installation of wind farms. However, in order to make better use of the wind potential, it is necessary to evaluate the operating conditions of the turbines and guide the independent power producers (IPPs) on how to efficiently use wind power. The investigation of the wind farm operating conditions is justified by the fact that the implementation of wind power systems is quite expensive, and therefore, it is imperative to find alternatives to reduce power losses and improve energy production. Taking into account the power needs in Mozambique, this project applied hybrid optimisation of multiple energy resources (HOMER) to size the capacity of the wind farm and the number of turbines that guarantee an adequate supply of power. Moreover, considering the topographic conditions of the site and the operational parameters of the turbines, the system advisor model (SAM) was applied to evaluate the performance of the Vestas V82-1.65 horizontal axis turbines and the system’s power output as a result of the wake effect. For any wind farm, it is evident that wind turbines’ wake effects significantly reduce the performance of wind farms. The paper seeks to design and examine the proper layout for practical placements of wind generators. Firstly, a survey on the Namaacha’s electricity demand was carried out in order to obtain the district’s daily load profile required to size the wind farm’s capacity. Secondly, with the previous knowledge that the operation of wind farms is affected by wake losses, different wake effect models applied by SAM were examined and the Eddy–Viscosity model was selected to perform the analysis. Three distinct layouts result from SAM optimisation, and the best one is recommended for wind turbines installation for maximising wind to energy generation. Although it is understood that the wake effect occurs on any wind farm, it is observed that wake losses can be minimised through the proper design of the wind generators’ placement layout. Therefore, any wind farm project should, from its layout, examine the optimal wind farm arrangement, which will depend on the wind speed, wind direction, turbine hub height, and other topographical characteristics of the area. In that context, considering the topographic and climate features of Mozambique, the study brings novelty in the way wind farms should be placed in the district and wake losses minimised. The study is based on a real assumption that the project can be implemented in the district, and thus, considering the wind farm’s capacity, the district’s energy needs could be met. The optimal transversal and longitudinal distances between turbines recommended are 8Do and 10Do, respectively, arranged according to layout 1, with wake losses of about 1.7%, land utilisation of about 6.46 Km2, and power output estimated at 71.844 GWh per year.

scholarly journals Modified Power Curves for Prediction of Power Output of Wind Farms

Energies ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1805 ◽  
Author(s):  
Mohsen Vahidzadeh ◽  
Corey D. Markfort
Keyword(s):  
High Resolution ◽  
Wind Speed ◽  
Wind Turbines ◽  
Power Output ◽  
Wind Farm ◽  
Sonic Anemometer ◽  
Wind Farms ◽  
Operating Conditions ◽  
Horizontal Axis Wind Turbine ◽  
Power Curves

Power curves are used to model power generation of wind turbines, which in turn is used for wind energy assessment and forecasting total wind farm power output of operating wind farms. Power curves are based on ideal uniform inflow conditions, however, as wind turbines are installed in regions of heterogeneous and complex terrain, the effect of non-ideal operating conditions resulting in variability of the inflow must be considered. We propose an approach to include turbulence, yaw error, air density, wind veer and shear in the prediction of turbine power by using high resolution wind measurements. In this study, two modified power curves using standard ten-minute wind speed and high resolution one-second data along with a derived power surface were tested and compared to the standard operating curve for a 2.5 MW horizontal axis wind turbine. Data from supervisory control and data acquisition (SCADA) system along with wind speed measurements from a nacelle-mounted sonic anemometer and wind speed measurements from a nearby meteorological tower are used in the models. The results show that all of the proposed models perform better than the standard power curve while the power surface results in the most accurate power prediction.

scholarly journals Frequency Scan–Based Mitigation Approach of Subsynchronous Control Interaction in Type-3 Wind Turbines

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4626
Author(s):  
Faris Alatar ◽  
Ali Mehrizi-Sani
Keyword(s):  
Wind Turbines ◽  
Wind Farm ◽  
Operating Conditions ◽  
Steady State Operation ◽  
Significant Damage ◽  
Frequency Scan ◽  
Type 3 ◽  
Phase Angles ◽  
Wind Energy Resources ◽  
Control Interaction

Integration of wind energy resources into the grid creates several challenges for power system dynamics. More specifically, Type-3 wind turbines are susceptible to subsynchronous control interactions (SSCIs) when they become radially connected to a series-compensated transmission line. SSCIs can cause disruptions in power generation and can result in significant damage to wind farm (WF) components and equipment. This paper proposes an approach to mitigate SSCIs using an online frequency scan, with optimized phase angles of voltage harmonic injection to maintain steady-state operation, to modify the controllers or the operating conditions of the wind turbine. The proposed strategy is simulated in PSCAD/EMTDC software on the IEEE second benchmark model for subsynchronous resonance. Simulation results demonstrate the effectiveness of this strategy by ensuring oscillations do not grow.

Evaluation of the Dynamic-Response-Based Intact Stability Criterion for Floating Wind Turbines

2015 ◽  
Author(s):  
Marco Masciola ◽  
Xiaohong Chen ◽  
Qing Yu
Keyword(s):  
Wind Speed ◽  
Dynamic Response ◽  
Wind Turbines ◽  
Stability Criterion ◽  
Area Ratio ◽  
Operating Conditions ◽  
Dynamic Responses ◽  
Stability Criteria ◽  
Intact Stability ◽  
Overturning Moment

As an alternative to the conventional intact stability criterion for floating offshore structures, known as the area-ratio-based criterion, the dynamic-response-based intact stability criteria was initially developed in the 1980s for column-stabilized drilling units and later extended to the design of floating production installations (FPIs). Both the area-ratio-based and dynamic-response-based intact stability criteria have recently been adopted for floating offshore wind turbines (FOWTs). In the traditional area-ratio-based criterion, the stability calculation is quasi-static in nature, with the contribution from external forces other than steady wind loads and FOWT dynamic responses captured through a safety factor. Furthermore, the peak wind overturning moment of FOWTs may not coincide with the extreme storm wind speed normally prescribed in the area-ratio-based criterion, but rather at the much smaller rated wind speed in the power production mode. With these two factors considered, the dynamic-response-based intact stability criterion is desirable for FOWTs to account for their unique dynamic responses and the impact of various operating conditions. This paper demonstrates the implementation of a FOWT intact stability assessment using the dynamic-response-based criterion. Performance-based criteria require observed behavior or quantifiable metrics as input for the method to be applied. This is demonstrated by defining the governing load cases for two conceptual FOWT semisubmersible designs at two sites. This work introduces benchmarks comparing the area-ratio-based and dynamic-response-based criteria, gaps with current methodologies, and frontier areas related to the wind overturning moment definition.

Prevention of Low-Frequency Vibration of High-Capacity Steam Turbine Units

1997 ◽  
Author(s):  
H. Kanki ◽  
Y. Kaneko ◽  
M. Kurosawa ◽  
T. Yamamoto ◽  
Y. Yamamoto ◽  
...  
Keyword(s):  
High Pressure ◽  
High Capacity ◽  
Low Frequency ◽  
Field Tests ◽  
Operating Conditions ◽  
Squeeze Film ◽  
High Pressure Turbine ◽  
Solution Approach ◽  
Vibration Excitation ◽  
Low Frequency Vibration

Abstract The causes of low-frequency vibration (subsynchronous vibration) of a high pressure turbine were investigated analytically and also via vibration excitation tests on actual machines under operation. From the results, it was concluded that low-frequency vibrations may be caused by either the decrease of the rotor system damping or by external forces, such as flow disturbance in the control stage and the rubbing between the rotor and casing. After identifying the cause of the low-frequency vibration, appropriate countermeasures such as installation of a squeeze-film damper and modification of valve opening sequence were taken. Vibration measurements and vibration excitation tests for the high pressure turbine under actual operating conditions were carried out in order to verify the validity of the countermeasures. These field tests confirmed that the problems of low-frequency vibration can be solved completely by taking the appropriate countermeasure depending on the cause of the vibration. This paper presents some field experiences of low-frequency vibration and the effective solution approach.

scholarly journals Evaluation of the Wind Potential and Optimal Design of a Wind Farm in The Arzew Industrial Zone in Western Algeria

2020 ◽  
Vol 9 (2) ◽  
pp. 177-187
Author(s):  
Salah Marih ◽  
Leila Ghomri ◽  
Benaissa Bekkouche
Keyword(s):  
Wind Speed ◽  
Wind Turbines ◽  
Wind Farm ◽  
Clean Energy ◽  
Appropriate Technology ◽  
Environmental Study ◽  
Net Energy ◽  
Electricity Grid ◽  
Wind Potential ◽  
Mean Wind Speed

This work presents an assessment of the wind potential and a design methodology for a 10 MW wind farm in the Arzew industrial region, located in northwest Algeria, to improve the quality of service of the electricity grid and increase Algeria's participation in the use of renewable energy. The hourly wind data of 10 years (2005-2015) that correspond to the wind potential of the site were analyzed, such as: dominant wind directions, probability distribution, Weibull parameters, mean wind speed and power potential. The site has a mean annual wind speed of 4.46 m/s at 10m height, and enough space to locate the wind turbines. A comparative study was carried out between four wind turbine technologies to improve the site's efficiency and select the appropriate technology: PowerWind 56/ 900 kW, Nordex N50/800 kW, Vestas V50/850 kW, NEG-Micon 44/750 kW. The estimate of the energy produced using WAsP software and the choice of the optimal architectural configuration for wind turbines installation was confirmed. A techno-economic and environmental study was carried out by HOMER software, to choose the model that produces the maximum annual net energy with a competitive cost in the global wind energy market, $ 0.068/kWh, and that provides clean energy with a reduced emission of polluting gases. Finally, this work provides a good indicator for the construction of a wind farm in Arzew. ©2020. CBIORE-IJRED. All rights reserved

Experiment of Adiabatic Two-Phase Flow in an Annulus Under Low-Frequency Vibration

2012 ◽  
Author(s):  
Shao-Wen Chen ◽  
Caleb S. Brooks ◽  
Chris Macke ◽  
Takashi Hibiki ◽  
Mamoru Ishii ◽  
...  
Keyword(s):  
Void Fraction ◽  
Two Phase Flow ◽  
Low Frequency ◽  
Flow Regimes ◽  
Operating Conditions ◽  
Phase Flow ◽  
Two Phase ◽  
Specific Flow ◽  
Low Frequency Vibration ◽  
Fft Analysis

In order to investigate the possible effect of seismic vibration on two-phase flow dynamics and thermal-hydraulics of a nuclear reactor, experimental tests of adiabatic air-water two-phase flow under low-frequency vibration were carried out in this study. An eccentric cam vibration module operated at low motor speed (up to 390rpm) was attached to an annulus test section which was scaled down from a prototypic BWR fuel assembly sub-channel. The inner and outer diameters of the annulus are 19.1mm and 38.1mm, respectively. The two-phase flow operating conditions cover the ranges of 0.03≤<jg> ≤1.46m/s and 0.25≤<jf>≤1.00m/s and the vibration displacement ranges from ±0.8mm to ±22.2mm. Steady-state area-averaged instantaneous and time-averaged void fraction was recorded and analyzed in stationary and vibration experiments. A neural network flow regime identification technique and fast Fourier transformation (FFT) analysis were introduced to analyze the flow regimes and void signals under stationary and vibration conditions. Experimental results reveal possible changes in flow regimes under specific flow and vibration conditions. In addition, the instantaneous void fraction signals were affected and shown by FFT analysis. Possible reasons for the changes include the applied high acceleration and/or induced resonance at certain ports under the specific flow and vibration conditions.

Development of Small-Sized Motor-Driven Gyroscopic Power Generator Works Under Low-Frequency Vibration

2019 ◽  
Author(s):  
Akio Toyoshima ◽  
Hiroshi Hosaka ◽  
Akira Yamashita
Keyword(s):  
High Speed ◽  
Low Frequency ◽  
Spindle Motor ◽  
Inertia Force ◽  
Power Generator ◽  
Power Generators ◽  
Mechanical Parts ◽  
Low Frequency Vibration ◽  
Generator Type ◽  
Design Freedom

Abstract In order to realize a small-sized energy harvester with high output, this study prototypes a small motor-driven gyroscopic power generator. Supplying energy to sensors and devices is the biggest problem for Internet of Things (IoT) systems. One solution is gyroscopic power generators, which are a type of vibrational generator that amplify the inertia force of weights by rotating them at high speed, and in doing so can obtain greater output than conventional generators that use simple vibration for the same mass weight. This paper reports on a motor-driven type gyroscopic generator in which the flywheel is spun with an embedded motor, and which is superior in applicability to random vibration generators. The generators of this type that have been studied thus far are very large and have been primarily used for wave power generation in the ocean. However, when the shape of this gyroscopic power generator type is miniaturized proportionally, the output per volume decreases in proportion to the fifth power of the dimension. This makes it difficult to maintain the power output while miniaturizing the generator size. In this research, the structure of the gyroscopic power generator is thoroughly refined and miniaturization is realized by making full use of the available space. By using a motor with high design freedom, the spindle motor and flywheel are unified. From this accomplishment, not only is the required space reduced, the number of mechanical parts and the friction loss are decreased as well. The prototype generator has a size of about 150 mm on its long side. When a swinging vibration of 50 degrees in amplitude and 2 Hz in frequency is applied, a net output of 0.104 W is obtained. This output power is sufficient to drive sensors and low power wide area (LPWA) radio circuits.

Fundamental Study on Friction-Driven Gyroscopic Power Generator Works Under Arbitrary Vibration

2019 ◽  
Author(s):  
Aya Watanabe ◽  
Ryousuke Yuyama ◽  
Hiroshi Hosaka ◽  
Akira Yamashita
Keyword(s):  
Power Generation ◽  
High Speed ◽  
Electrical Power ◽  
Low Frequency ◽  
Inertial Force ◽  
Fundamental Study ◽  
Power Generator ◽  
Energy Harvesters ◽  
Low Frequency Vibration ◽  
Circular Track

Abstract This paper describes a friction-driven gyro generator that works under arbitrary vibrations and generates more than 1 W of power. Vibrational generators are energy harvesters that convert environmental vibrations into electrical power via the inertial force of pendulums. In conventional generators that use simple vibration, the power is less than 10 mW for a wearable size because vibrations in the natural environment are as low as 1 Hz. Gyroscopic generators increase the inertial force by rotating a pendulum at high speed and creating a gyro effect. In this generator, a palm-size product that generates 0.1 W and weighs 280 g has already been commercialized, but this device operates only under a particular vibration that synchronizes rotor precession and stalls under random vibration. To solve this problem, in this research, two gimbals and a precession spring are introduced to support the rotor. We developed a prototype generator with straight tracks measuring 16 cm × 11 cm × 12 cm with a mass of 980 g. Under a vibration of 4 Hz and ±20 degrees, power generation of 1.6 W was confirmed. Next, a prototype circular track was made. Power generation of 0.2 W with a vibration of 1 Hz and ±90 degrees was confirmed. Finally, a simple formula to estimate the upper limit of the generation power is derived. It is suggested that the circular-type generator is suitable for low-frequency vibration and can generate twice the power of a straight-type generator.

scholarly journals Wake and Turbulence Analysis for Wind Turbine Layouts in an Island

2018 ◽  
Vol 64 ◽  
pp. 06010
Author(s):  
Bachhal Amrender Singh ◽  
Vogstad Klaus ◽  
Lal Kolhe Mohan ◽  
Chougule Abhijit ◽  
Beyer Hans George
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Production ◽  
Wind Farm ◽  
Full Length Paper ◽  
Turbulence Analysis ◽  
Wake Model ◽  
Wind Resources

There is a big wind energy potential in supplying the power in an island and most of the islands are off-grid. Due to the limited area in island(s), there is need to find appropriate layout / location for wind turbines suited to the local wind conditions. In this paper, we have considered the wind resources data of an island in Trøndelag region of the Northern Norway, situated on the coastal line. The wind resources data of this island have been analysed for wake losses and turbulence on wind turbines for determining appropriate locations of wind turbines in this island. These analyses are very important for understanding the fatigue and mechanical stress on the wind turbines. In this work, semi empirical wake model has been used for wake losses analysis with wind speed and turbine spacings. The Jensen wake model used for the wake loss analysis due to its high degree of accuracy and the Frandsen model for characterizing the turbulent loading. The variations of the losses in the wind energy production of the down-wind turbine relative to the up-wind turbine and, the down-stream turbulence have been analysed for various turbine distances. The special emphasis has been taken for the case of wind turbine spacing, leading to the turbulence conditions for satisfying the IEC 61400-1 conditions to find the wind turbine layout in this island. The energy production of down-wind turbines has been decreased from 2 to 20% due to the lower wind speeds as they are located behind up-wind turbine, resulting in decreasing the overall energy production of the wind farm. Also, the higher wake losses have contributed to the effective turbulence, which has reduced the overall energy production from the wind farm. In this case study, the required distance for wind turbines have been changed to 6 rotor diameters for increasing the energy gain. From the results, it has been estimated that the marginal change in wake losses by moving the down-stream wind turbine by one rotor diameter distance has been in the range of 0.5 to 1% only and it is insignificant. In the full-length paper, the wake effects with wind speed variations and the wind turbine locations will be reported for reducing the wake losses on the down-stream wind turbine. The Frandsen model has been used for analysing turbulence loading on the down-stream wind turbine as per IEC 61400-1 criteria. In larger wind farms, the high turbulence from the up-stream wind turbines increases the fatigues on the turbines of the wind farm. In this work, we have used the effective turbulence criteria at a certain distance between up-stream and down-stream turbines for minimizing the fatigue load level. The sensitivity analysis on wake and turbulence analysis will be reported in the full-length paper. Results from this work will be useful for finding wind farm layouts in an island for utilizing effectively the wind energy resources and electrification using wind power plants.

Sign in / Sign up

Export Citation Format

Share Document