Flow Field and Hot Streak Migration Through a High Pressure Cooled Vanes With Representative Lean Burn Combustor Outflow

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
Tommaso Bacci ◽  
Tommaso Lenzi ◽  
Alessio Picchi ◽  
Lorenzo Mazzei ◽  
Bruno Facchini
Keyword(s):  
Experimental Data ◽  
High Pressure ◽  
Flow Field ◽  
Fuel Injection ◽  
Leading Edge ◽  
Flame Stabilization ◽  
Lean Burn ◽  
Aero Engine ◽  
University Of Florence ◽  
Hot Streak

Modern lean burn aero-engine combustors make use of relevant swirl degrees for flame stabilization. Moreover, important temperature distortions are generated, in tangential and radial directions, due to discrete fuel injection and liner cooling flows respectively. At the same time, more efficient devices are employed for liner cooling and a less intense mixing with the mainstream occurs. As a result, aggressive swirl fields, high turbulence intensities, and strong hot streaks are achieved at the turbine inlet. In order to understand combustor-turbine flow field interactions, it is mandatory to collect reliable experimental data at representative flow conditions. While the separated effects of temperature, swirl, and turbulence on the first turbine stage have been widely investigated, reduced experimental data is available when it comes to consider all these factors together.In this perspective, an annular three-sector combustor simulator with fully cooled high pressure vanes has been designed and installed at the THT Lab of University of Florence. The test rig is equipped with three axial swirlers, effusion cooled liners, and six film cooled high pressure vanes passages, for a vortex-to-vane count ratio of 1:2. The relative clocking position between swirlers and vanes has been chosen in order to have the leading edge of the central NGV aligned with the central swirler. In order to generate representative conditions, a heated mainstream passes though the axial swirlers of the combustor simulator, while the effusion cooled liners are fed by air at ambient temperature. The resulting flow field exiting from the combustor simulator and approaching the cooled vane can be considered representative of a modern Lean Burn aero engine combustor with swirl angles above ±50 deg, turbulence intensities up to about 28% and maximum-to-minimum temperature ratio of about 1.25. With the final aim of investigating the hot streaks evolution through the cooled high pressure vane, the mean aerothermal field (temperature, pressure, and velocity fields) has been evaluated by means of a five-hole probe equipped with a thermocouple and traversed upstream and downstream of the NGV cascade.

Flow Field and Hot Streak Migration Through High Pressure Cooled Vanes With Representative Lean Burn Combustor Outflow

2018 ◽  
Author(s):  
T. Bacci ◽  
T. Lenzi ◽  
A. Picchi ◽  
L. Mazzei ◽  
B. Facchini
Keyword(s):  
Experimental Data ◽  
High Pressure ◽  
Flow Field ◽  
Fuel Injection ◽  
Leading Edge ◽  
Flame Stabilization ◽  
Lean Burn ◽  
Aero Engine ◽  
University Of Florence ◽  
Hot Streak

Modern lean burn aero-engine combustors make use of relevant swirl degrees for flame stabilization. Moreover important temperature distortions are generated, in tangential and radial directions, due to discrete fuel injection and liner cooling flows respectively. At the same time, more efficient devices are employed for liner cooling and a less intense mixing with the mainstream occurs. As a result, aggressive swirl fields, high turbulence intensities and strong hot streaks are achieved at the turbine inlet. In order to understand combustor-turbine flow field interactions, it is mandatory to collect reliable experimental data at representative flow conditions. While the separated effects of temperature, swirl and turbulence on the first turbine stage have been widely investigated, reduced experimental data is available when it comes to consider all these factors together. In this perspective, an annular three-sector combustor simulator with fully cooled high pressure vanes has been designed and installed at the THT Lab of University of Florence. The test rig is equipped with three axial swirlers, effusion cooled liners and six film cooled high pressure vanes passages, for a vortex-to-vane count ratio of 1:2. The relative clocking position between swirlers and vanes has been chosen in order to have the leading edge of the central NGV aligned with the central swirler. In order to generate representative conditions, a heated mainstream passes though the axial swirlers of the combustor simulator, while the effusion cooled liners are fed by air at ambient temperature. The resulting flow field exiting from the combustor simulator and approaching the cooled vane can be considered representative of a modern Lean Burn aero engine combustor with swirl angles above ±50°, turbulence intensities up to about 28% and maximum-to-minimum temperature ratio of about 1.25. With the final aim of investigating the hot streaks evolution through the cooled high pressure vane, the mean aerothermal field (temperature, pressure and velocity fields) has been evaluated by means of a five hole probe equipped with a thermocouple and traversed upstream and downstream of the NGV cascade.

Investigation of Combustor-Turbine-Interaction in a Rotating Cooled Transonic High-Pressure Turbine Test Rig: Part 2 — Numerical Modelling and Simulation

2019 ◽  
Author(s):  
Simon Gövert ◽  
Federica Ferraro ◽  
Alexander Krumme ◽  
Clemens Buske ◽  
Marc Tegeler ◽  
...  
Keyword(s):  
High Pressure ◽  
Flame Stabilization ◽  
Test Facility ◽  
Test Rig ◽  
High Pressure Turbine ◽  
Lean Burn ◽  
Turbine Inlet ◽  
Measurement Results ◽  
Aero Engine ◽  
Inlet Conditions

Abstract Reducing the uncertainties in the prediction of turbine inlet conditions is a crucial aspect to improve aero engine designs and further increase engine efficiencies. To meet constantly stricter emission regulations, lean burn combustion could play a key role for future engine designs. However, these combustion systems are characterized by significant swirl for flame stabilization and reduced cooling air mass flows. As a result, substantial spatial and transient variations of the turbine inlet conditions are encountered. To investigate the effect of the combustor on the high pressure turbine, a rotating cooled transonic high-pressure configuration has been designed and investigated experimentally at the DLR turbine test facility ‘NG-Turb’ in Göttingen, Germany. It is a rotating full annular 1.5 stage turbine configuration which is coupled to a combustor simulator. The combustor simulator is designed to create turbine inlet conditions which are hydrodynamically representative for a lean-burn aero engine. A detailed description of the test rig and its instrumentation as well as a discussion of the measurement results is presented in part I of this paper. Part II focuses on numerical modeling of the test rig to further extend the understanding of the measurement results. Integrated simulations of the configuration including combustor simulator and nozzle guide vanes are performed for leading edge and passage clocking position and the effect on the hot streak migration is discussed. The simulation and experimental results at the combustor-turbine interface are compared showing a good overall agreement. The relevant flow features are correctly predicted in the simulations, proving the suitability of the numerical model for application to integrated combustor-turbine interaction analysis.

Large Eddy Simulations of the Combustor Turbine Interface: Study of the Potential and Clocking Effects

2016 ◽  
Author(s):  
Charlie Koupper ◽  
Guillaume Bonneau ◽  
Laurent Gicquel ◽  
Florent Duchaine
Keyword(s):  
Flow Field ◽  
Leading Edge ◽  
Integrated Approach ◽  
Potential Effect ◽  
Interface Plane ◽  
Mean Flow ◽  
Lean Burn ◽  
Large Eddy ◽  
Inlet Conditions ◽  
Hot Streak

With the generalization of Lean Burn combustors, the flow field entering the turbine tends to feature higher levels of swirl, turbulence, while different hot streak patterns often emerge if compared to the previous generation of combustion chambers. In this context, the combustor-turbine interactions and more specifically the transport of hot streaks through the turbine need to be further analysed to gain engine performance and improved turbine life. Considering this new context, a non-reactive axial combustor simulator representative of a Lean Burn architecture, together with a 1.5 high pressure turbine stage is developed within the European project FACTOR. The interaction between these two modules is numerically investigated by performing Large Eddy Simulation (LES) of the combustor simulator equipped with two Nozzle Guide Vanes (NGVs). By using such an integrated approach, the combustor-turbine interface (plane 40) disappears, allowing: (i) more realistic inlet conditions to the turbine by suppressing all the assumptions associated with averaged profiles; (ii) to account for the potential effect of the vanes on the chamber. Note that if compared to classical approaches, the use of time-resolved LES has the advantage of well predicting the combustor mean flow and turbulence, resulting in more realistic flow properties at the turbine inlet as confirmed by previous works on this configuration. This paper focuses first on two LESs of the combustor-turbine specific configurations: i.e., two clocking positions of the hot streak relative to the NGVs. Significant changes on the thermal field around the vanes are highlighted. When the hot streak is injected in front of a vane leading edge, it considerably heats up the pressure side compared to the adjacent vane although the temperature field is quite uniform at the NGV exit because of the enhanced mixing of the hot streak. On the other hand, when the hot streak is injected in the passage between two adjacent vanes, it remains away from the vane walls preventing them from heating up. The hot streak however crosses the vane passage without being significantly distorted resulting in a more heterogeneous flow field at the rotor inlet. Second, the potential effect induced by the presence of the vanes is investigated by comparing the flow field inside the chamber with and without NGVs. It is found that the potential effect does not alter temperature patterns while a significant radial and azimuthal mass flow redistribution is observed up to about 25% axial chord length upstream of the vanes. The turbulence level is affected by the presence of vanes up to plane 40 when the hot streak is aligned with the passage.

Experimental and Numerical Calculation of Turbulent Timescales at the Exit of an Engine Representative Combustor Simulator

2015 ◽  
Author(s):  
Charlie Koupper ◽  
Tommaso Bacci ◽  
Bruno Facchini ◽  
Alessio Picchi ◽  
Lorenzo Tarchi ◽  
...  
Keyword(s):  
High Pressure ◽  
Experimental Investigations ◽  
Time Signal ◽  
Small Scale ◽  
Lean Burn ◽  
Integral Scale ◽  
Eddy Simulation ◽  
High Reynolds ◽  
University Of Florence ◽  
Hot Streak

To deepen the knowledge of the interaction between modern lean burn combustors and high pressure turbines, a non-reactive real scale annular trisector Combustor Simulator (CS) has been assembled at University of Florence, with the goal of investigating and characterizing the combustor aerothermal field as well as the hot streak transport towards the high pressure vanes. To generate hot streaks and simulate lean burn combustor behaviors, the rig is equipped with axial swirlers fed by a main air flow stream that is heated up to 531 K, while liners with effusion cooling holes are fed by air at ambient temperature. Detailed experimental investigations are then performed with the aim of characterizing the turbulence quantities at the exit of the combustion module, and specifically evaluating an integral scale of turbulence. To do so, an automatic traverse system is mounted at the exit of the CS and equipped to perform Hot Wire Anemometry (HWA) measurements. In this paper, two-point correlations are computed from the time signal of the axial velocity giving access to an evaluation of the turbulence timescales at each measurement point. For assessment of the advanced numerical method that is Large Eddy Simulation (LES), the same methodology is applied to a LES prediction of the CS. Although comparisons seem relevant and easily accessible, both approaches and contexts have fundamental differences: mostly in terms of duration of the signals acquired experimentally and numerically but also with potentially different acquisition frequencies. In the exercise that aims at comparing high-order statistics and diagnostics, the specificity of comparing experimental and numerical results is comprehensively discussed. Attention is given to the importance of the acquisition frequency, intrinsic bias of having a short duration signal and influence of the investigating windows. For an adequate evaluation of the turbulent time scales, it is found that comparing experiments and numerics for high Reynolds number flows inferring small-scale phenomena requires to obey a set of rules, otherwise important errors can be made. If adequately processed, LES and HWA are found to agree well indicating the potential of LES for such problems.

Adiabatic Effectiveness on High Pressure Turbine Nozzle Guide Vanes Under Realistic Swirling Conditions

2018 ◽  
Author(s):  
T. Bacci ◽  
R. Becchi ◽  
A. Picchi ◽  
B. Facchini
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
Swirling Flow ◽  
Cooling System ◽  
Density Ratio ◽  
Leading Edge ◽  
Suction Side ◽  
Flame Stabilization ◽  
Lean Burn ◽  
Relevant Effect

In modern lean burn aero-engine combustors, highly swirling flow structures are adopted to control the fuel-air mixing and to provide the correct flame stabilization mechanisms. Aggressive swirl fields and high turbulence intensities are hence expected in the combustor-turbine interface. Moreover, to maximize the engine cycle efficiency, an accurate design of the high pressure nozzle cooling system must be pursued: in a film cooled nozzle the air taken from last compressor stages is ejected through discrete holes drilled on vane surfaces to provide a cold layer between hot gases and turbine components. In this context, the interactions between the swirling combustor outflow and the vane film cooling flows play a major role in the definition of a well performing cooling scheme, demanding for experimental campaigns at representative flow conditions. An annular three-sector combustor simulator with fully cooled high pressure vanes has been designed and installed at THT Lab of University of Florence. The test rig is equipped with three axial swirlers, effusion cooled liners and six film cooled high pressure vanes passages, for a vortex-to-vane count ratio of 1:2. The relative clocking position between swirlers and vanes has been chosen in order to have the leading edge of the central airfoil aligned with the central swirler. In this experimental work, adiabatic film effectiveness measurements have been carried out in the central sector vanes, in order to characterize the film-cooling performance under swirling inflow conditions. The Pressure Sensitive Paint technique, based on heat and mass transfer analogy, has been exploited to catch highly detailed 2D distributions. Carbon dioxide has been used as coolant in order to reach a coolant-to-mainstream density ratio of 1.5. Turbulence and five hole probe measurements at inlet/outlet of the cascade have been carried out as well, in order to highlight the characteristics of the flow field passing through the cascade and to provide precise boundary conditions. Results have shown a relevant effect of the swirling mainflow on the film cooling behaviour. Differences have been found between the central airfoil and the adjacent ones, both in terms of leading edge stagnation point position and of pressure and suction side film coverage characteristics.

Flowfield and Temperature Profiles Measurements on a Combustor Simulator Dedicated to Hot Streaks Generation

2015 ◽  
Author(s):  
Tommaso Bacci ◽  
Gianluca Caciolli ◽  
Bruno Facchini ◽  
Lorenzo Tarchi ◽  
Charlie Koupper ◽  
...  
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Measurement Techniques ◽  
Symmetry Plane ◽  
Operating Conditions ◽  
Pressure Probe ◽  
Lean Burn ◽  
Experimental Database ◽  
Set Up ◽  
University Of Florence

In order to deepen the knowledge of the interaction between modern lean burn combustors and high pressure turbines, a real scale annular three sector combustor simulator has been assembled at University of Florence, with the goal of investigating and characterizing the generated aerothermal field and the hot streaks transport between combustor exit and the high pressure vanes location. To generate hot streaks and simulate lean burn combustors behavior, the rig is equipped with axial swirlers, fed by main air flow that is heated up to 531 K, and liners with effusion cooling holes that are fed by air at ambient temperature. The three sector configuration is used to reproduce the periodicity on the central sector and to allow to perform measurements inside the chamber, through the lateral walls. Ducts of different length have been mounted on the swirlers, preserving the hot mainflow from the interaction with coolant. Such configurations, together with the one without ducts, have been tested, using different measurement techniques, in order to highlight the differences in the resulting flow fields. First of all, isothermal PIV measurements have been performed on the combustion chamber symmetry plane, to highlight the mixing phenomena between the mainflow and cooling flows. Then a detailed investigation of the mean aerothermal field at combustor exit has been carried out, for nominal operating conditions, by means of a five hole pressure probe provided with a thermocouple, installed on an automatic traverse system. With the aim of analyzing the hot streaks transport and the flow field modification towards the vanes location, such measurements have been performed on two different planes: one located in correspondence of the combustor exit and the further one placed downstream, in the virtual location of the vanes leading edges. Therefore, an experimental database, describing the evolution of the flow field in a combustor simulator with typical traits of modern lean burn chambers, for different injector geometries, has been set up.

Adiabatic Effectiveness on High-Pressure Turbine Nozzle Guide Vanes Under Realistic Swirling Conditions

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
Tommaso Bacci ◽  
Riccardo Becchi ◽  
Alessio Picchi ◽  
Bruno Facchini
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
Swirling Flow ◽  
Cooling System ◽  
Density Ratio ◽  
Leading Edge ◽  
Suction Side ◽  
Flame Stabilization ◽  
Lean Burn ◽  
Relevant Effect

In modern lean-burn aero-engine combustors, highly swirling flow structures are adopted to control the fuel-air mixing and to provide the correct flame stabilization mechanisms. Aggressive swirl fields and high turbulence intensities are hence expected in the combustor-turbine interface. Moreover, to maximize the engine cycle efficiency, an accurate design of the high-pressure nozzle cooling system must be pursued: in a film-cooled nozzle, the air taken from last compressor stages is ejected through discrete holes drilled on vane surfaces to provide a cold layer between hot gases and turbine components. In this context, the interactions between the swirling combustor outflow and the vane film cooling flows play a major role in the definition of a well-performing cooling scheme, demanding for experimental campaigns at representative flow conditions. An annular three-sector combustor simulator with fully cooled high-pressure vanes has been designed and installed at THT Lab of University of Florence. The test rig is equipped with three axial swirlers, effusion-cooled liners, and six film-cooled high-pressure vanes passages, for a vortex-to-vane count ratio of 1:2. The relative clocking position between swirlers and vanes has been chosen in order to have the leading edge of the central airfoil aligned with the central swirler. In this experimental work, adiabatic film effectiveness measurements have been carried out in the central sector vanes, in order to characterize the film-cooling performance under swirling inflow conditions. The pressure-sensitive paint (PSP) technique, based on heat and mass transfer analogy, has been exploited to catch highly detailed 2D distributions. Carbon dioxide has been used as coolant in order to reach a coolant-to-mainstream density ratio of 1.5. Turbulence and five-hole probe measurements at inlet/outlet of the cascade have been carried out as well, in order to highlight the characteristics of the flow field passing through the cascade and to provide precise boundary conditions. Results have shown a relevant effect of the swirling mainflow on the film cooling behavior. Differences have been found between the central airfoil and the adjacent ones, both in terms of leading edge stagnation point position and of pressure and suction side film coverage characteristics.

Assessment of RANS Against LES for the Aero-Thermal Behavior of High Pressure Turbine Stages Under Realistic Inlet Conditions

2016 ◽  
Author(s):  
Stefano Vagnoli ◽  
Tom Verstraete ◽  
Charlie Koupper ◽  
Guillaume Bonneau
Keyword(s):  
High Pressure ◽  
Thermal Behavior ◽  
Turbulence Modeling ◽  
Engine Performance ◽  
High Pressure Turbine ◽  
Lean Burn ◽  
Field Development ◽  
Safety Margins ◽  
Inlet Conditions ◽  
Hot Streak

Modern Lean Burn combustors generate a complex field at the High Pressure turbine (HPT) inlet, characterized by non-uniform velocity and temperature distributions, together with very high turbulence levels (up to 25%). For these extreme conditions, classical numerical methods employed for the HPT design, such as Reynolds Averaged Navier Stokes (RANS) simulation, suffer from a lack of validation. This leads to a reduced confidence in predicting the combustor-turbine interactions, which requires to use extra safety margins, to the detriment of the overall engine performance. Within the European FACTOR project, a 360° non reactive combustor simulator and a 1.5 HPT stage are designed to get more insight into the mutual interaction of these two components. A first experimental and numerical campaign has demonstrated the potential of Large Eddy Simulations (LES) to accurately reproduce the turbulent flow field development at the combustor outlet. The aim of the present paper is to exploit the accuracy of LES to validate less time-consuming RANS models in predicting the hot streak migration in the turbine stage. In this sense, LES results are used as a reference to discriminate the different RANS simulations in terms of turbulence modeling and aerothermal predictions. The current investigations clearly indicate that turbulence and hot streak diffusion within the HPT are strongly linked. In this sense, the choice of the RANS turbulence model and the inlet turbulent conditions plays a major role in modeling the thermal behavior for the stator and rotor blades.

Thermodynamic Analysis of Flow Field at the End of Combustor Simulator

2012 ◽  
Vol 225 ◽  
pp. 261-266 ◽  
Author(s):  
Kianpour Ehsan ◽  
Nor Azwadi Che Sidik ◽  
Mohsen Agha Seyyed Mirza Bozorg
Keyword(s):  
Flow Field ◽  
Penetration Depth ◽  
Thermodynamic Analysis ◽  
Film Cooling ◽  
Thermal Field ◽  
Three Dimensional ◽  
Leading Edge ◽  
Aero Engine ◽  
Three Dimensional Presentation

This study was carried out to investigate the effects of different cooling holes configurations on the thermal field characteristics inside a combustor simulator. In this research, a three-dimensional presentation of a true Pratt and Whitney aero-engine was simulated and analyzed. This combustor simulator combined the interaction of two rows of dilution jets, which were staggered in the stream wise direction and aligned in the span wise direction. The findings of the study indicate that the thickness of the film-cooling layer was thicker for the greater penetration depth. Furthermore, for the combustor simulator with more cooling holes, the temperature near the wall and between the jets was slightly increased. Also at the leading edge of the jet, the gradients of temperature were quite high at the jet-mainstream interface.

Low NOx Premixed Combustion of MBtu Fuels in a Research Burner

1997 ◽  
Vol 119 (3) ◽  
pp. 553-558 ◽  
Author(s):  
K. Do¨bbeling ◽  
A. Eroglu ◽  
D. Winkler ◽  
T. Sattelmayer ◽  
W. Keppel
Keyword(s):  
High Pressure ◽  
Quartz Glass ◽  
Atmospheric Pressure ◽  
Fuel Injection ◽  
Flame Stabilization ◽  
Premix Combustion ◽  
Planar Laser ◽  
Preliminary Study ◽  
Combustion Tests

The paper reports on the development and testing of a premix research burner for MBtu fuels. The burner has a quartz glass annular mixing section and a quartz, glass flame tube to allow visualization of the flame. A central lance is used to mount modules for fuel injection, swirl generation, and flame stabilization. This allows a large number of variants with different swirl strength, mixing section length, fuel injection geometry, and flameholder size and shape to be easily tested. Experiments have been performed at atmospheric pressure and under high-pressure conditions (14 bar pressure, 400°C air preheat temperature) for syngas with a H2/CO ratio of up to 5. In a preliminary study, the mixing quality of the tested variants has been assessed with planar laser-induced fluorescence (LIF). High-pressure combustion tests show that low NOx (<10 vppmd @ 15 percent O2) premix combustion of MBtu fuels under industrial GT conditions without dilution is feasible.

Sign in / Sign up

Export Citation Format

Share Document