Modeling Machine Motion and Process Parameter Errors for Improving Dimensional Accuracy of Fused Deposition Modeling Machines

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Jiaqi Lyu ◽  
Souran Manoochehri
Keyword(s):  
Computer Aided Design ◽  
Fused Deposition Modeling ◽  
Dimensional Accuracy ◽  
Processing Parameters ◽  
Error Model ◽  
Fused Deposition ◽  
Model Combining ◽  
Before And After ◽  
Deposition Modeling ◽  
Integrated Error

The dimensional accuracy of fused deposition modeling (FDM) machines is dependent on errors caused by processing parameters and machine motions. In this study, an integrated error model combining these effects is developed. Extruder temperature, layer thickness, and infill density are selected as parameters of this study for three FDM machines, namely, Flashforge Finder, Ultimaker 2 go, and XYZ da Vinci 2.0 Duo. Experiments have been conducted using Taguchi method and the interactions between processing parameters are analyzed. Based on the dimensional deviations between fabricated parts and the computer aided design (CAD) geometry, a set of coefficients for the integrated error model are calculated to characterize each machine. Based on the results of the integrated error model, the original CAD geometry is optimized for fabrication accuracy on each machine. New parts are fabricated using the optimized CAD geometries. Through comparing the dimensional deviations of parts fabricated before and after optimization, the effectiveness of the integrated error model is analyzed and demonstrated for the three FDM machines.

scholarly journals Compatibility of a Silicone Impression/Adhesive System to FDM-Printed Tray Materials—A Laboratory Peel-off Study

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1905 ◽  
Author(s):  
Yichen Xu ◽  
Alexey Unkovskiy ◽  
Felix Klaue ◽  
Frank Rupp ◽  
Juergen Geis-Gerstorfer ◽  
...  
Keyword(s):  
Computer Aided Design ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Adhesive System ◽  
Material Interface ◽  
Fused Deposition ◽  
Before And After ◽  
Light Curing ◽  
Deposition Modeling ◽  
Aided Design

Computer-aided design (CAD) and additive manufacturing (AM) have shown promise in facilitating the fabrication of custom trays. Due to the clinical requirements, custom tray materials should achieve good bonding to the impression/adhesive systems. This study evaluated the retention of three fused deposition modeling (FDM) custom tray materials to a silicone impression/adhesive system before and after gritblasting (GB) by peel-off test. CAD-designed experimental test blocks were printed by FDM using acrylonitrile butadiene styrene (ABS), polyethylene terephthalate glycol copolyester (PETG), and high impact polystyrene (HIPS), and the reference test blocks were made of a conventional light-curing resin (n = 11). Before and after GB, the surface topography of all tray materials was analysed, and the maximum strength of the test block peeled off from a silicone impression/adhesive system was measured. After GB, the arithmetic mean height (Sa) and the valley fluid retention index (Svi) of the four material groups declined (p < 0.05). The peel-off strength of each of the four material groups significantly decreased by GB (p < 0.05), but no statistical difference could be found among them before or after GB. In all peel-off tests, adhesive failure occurred at the adhesive-impression material interface. The results indicated ABS, HIPS, and PETG could provide sufficient adhesion to the adhesive as the conventional light-curing resin, and GB could reduce the roughness generated by FDM and weaken the bonding between the adhesive and the silicone impression.

scholarly journals Fused deposition modeling of polypropylene-aluminium silicate dihydrate microcomposites

e-Polymers ◽  
2022 ◽  
Vol 22 (1) ◽  
pp. 87-98
Author(s):  
Kilole Tesfaye Chaka
Keyword(s):  
Mechanical Properties ◽  
Fused Deposition Modeling ◽  
Tensile Modulus ◽  
Dimensional Accuracy ◽  
Processing Parameters ◽  
Screw Extruder ◽  
Scanning Calorimetry ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Aluminium Silicate

Abstract Polypropylene (PP) undergoes fast crystallization and resulting in rigorous shrinkage when it is subjected to high temperature likewise of the fused deposition modeling (FDM) process. This research study focuses on the investigation of the processing parameters and factors that decrease the warpage of PP during the FDM process. Aluminium silicate dihydrate (K) microparticles of different ratios were melt blended with PP by a twin-screw extruder, and filaments of about 1.7 mm diameter were extruded in a single screw extruder. Then, the extruded filaments were used to fabricate the dumbbells structure through the FDM process. The effects of optimizing the fused deposition temperature, coating the chamber with thick papers/fabrics, and coating a printer bed with PP material were also investigated in this study. Scanning and transmission electron microscopy, differential scanning calorimetry, melt flow, and mechanical properties testing instruments are used to analyze the microparticles dispersion, crystallization, flow, and mechanical properties of resulting samples. Uniformly dispersed filler and increased printing chamber temperature result in an increase of crystallization temperature and improve the dimensional accuracy of fused deposited specimens. The fused deposited PP-K10 wt% composite showed an improvement of up to 32% in tensile modulus compared to the neat PP.

Assessing the effect of FDM processing parameters on mechanical properties of PLA parts using Taguchi method

2021 ◽  
pp. 089270572110530
Author(s):  
Nagarjuna Maguluri ◽  
Gamini Suresh ◽  
K Venkata Rao
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Fused Deposition Modeling ◽  
Fracture Strain ◽  
Processing Parameters ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Nozzle Temperature ◽  
Experimental Runs ◽  
Printing Speed

Fused deposition modeling (FDM) is a fast-expanding additive manufacturing technique for fabricating various polymer components in engineering and medical applications. The mechanical properties of components printed with the FDM method are influenced by several process parameters. In the current work, the influence of nozzle temperature, infill density, and printing speed on the tensile properties of specimens printed using polylactic acid (PLA) filament was investigated. With an objective to achieve better tensile properties including elastic modulus, tensile strength, and fracture strain; Taguchi L8 array has been used for framing experimental runs, and eight experiments were conducted. The results demonstrate that the nozzle temperature significantly influences the tensile properties of the FDM printed PLA products followed by infill density. The optimum processing parameters were determined for the FDM printed PLA material at a nozzle temperature of 220°C, infill density of 100%, and printing speed of 20 mm/s.

Carbon Nanotube Reinforced Fused Deposition Modeling Using Microwave Irradiation

2016 ◽  
Author(s):  
Meng Zhang ◽  
Xiaoxu Song ◽  
Weston Grove ◽  
Emmett Hull ◽  
Z. J. Pei ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Additive Manufacturing ◽  
Microwave Irradiation ◽  
Computer Aided Design ◽  
Fused Deposition Modeling ◽  
Layer By Layer ◽  
Sem Images ◽  
Fused Deposition ◽  
Deposition Modeling

Additive manufacturing (AM) is a class of manufacturing processes where material is deposited in a layer-by-layer fashion to fabricate a three-dimensional part directly from a computer-aided design model. With a current market share of 44%, thermoplastic-based additive manufacturing such as fused deposition modeling (FDM) is a prevailing technology. A key challenge for AM parts (especially for parts made by FDM) in engineering applications is the weak inter-layer adhesion. The lack of bonding between filaments usually results in delamination and mechanical failure. To address this challenge, this study embedded carbon nanotubes into acrylonitrile butadiene styrene (ABS) thermoplastics via a filament extrusion process. The vigorous response of carbon nanotubes to microwave irradiation, leading to the release of a large amount of heat, is used to melt the ABS thermoplastic matrix adjacent to carbon nanotubes within a very short time period. This treatment is found to enhance the inter-layer adhesion without bulk heating to deform the 3D printed parts. Tensile and flexural tests were performed to evaluation the effects of microwave irradiation on mechanical properties of the specimens made by FDM. Scanning electron microscopic (SEM) images were taken to characterize the fracture surfaces of tensile test specimens. The actual carbon nanotube contents in the filaments were measured by conducting thermogravimetric analysis (TGA). The effects of microwave irradiation on the electrical resistivity of the filament were also reported.

scholarly journals Desain dan Pembuatan Prototype Piston Honda MEGAPRO FI Menggunakan 3D Printing

2020 ◽  
Vol 1 (2) ◽  
pp. 81-91
Author(s):  
Frince Marbun ◽  
Richard A.M. Napitupulu
Keyword(s):  
3D Printing ◽  
Computer Aided Design ◽  
Fused Deposition Modeling ◽  
Layer By Layer ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Manufacturing Technologies ◽  
Aided Design

3D printing technology has great potential in today's manufacturing world, one of its uses is in making miniatures or prototypes of a product such as a piston. One of the most famous and inexpensive 3D printing (additive manufacturing) technologies is Fused Deposition Modeling (FDM), the principle FDM works by thermoplastic extrusion through a hot nozzle at melting temperature then the product is made layer by layer. The two most commonly used materials are ABS and PLA so it is very important to know the accuracy of product dimensions. FDM 3D Printing Technology is able to make duplicate products accurately using PLA material. FDM machines work by printing parts that have been designed by computer-aided design (CAD) and then exported in the form of STL or .stl files and uploaded to the slicer program to govern the printing press according to the design. Using Anet A8 brand 3D printing tools that are available to the public, Slicing of general CAD geometry files such as autocad and solidwork is the basis for making this object. This software is very important to facilitate the design process to be printed. Some examples of software that can be downloaded and used free of charge such as Repetier-Host and Cura. by changing the parameters in the slicer software is very influential in the 3D printing manufacturing process.

scholarly journals Designing Thin 2.5D Parts Optimized for Fused Deposition Modeling

2019 ◽  
pp. 134-164 ◽  
Author(s):  
James I. Novak ◽  
Mark Zer-Ern Liu ◽  
Jennifer Loy
Keyword(s):  
Computer Aided Design ◽  
Fused Deposition Modeling ◽  
Outer Wall ◽  
Fused Deposition ◽  
Design Engineers ◽  
Test Pieces ◽  
New Knowledge ◽  
Deposition Modeling ◽  
Aided Design ◽  
Reference Graph

This chapter builds new knowledge for design engineers adopting fused deposition modeling (FDM) technology as an end manufacturing process, rather than simply as a prototyping process. Based on research into 2.5D printing and its use in real-world additive manufacturing situations, a study featuring 111 test pieces across the range of 0.4-4.0mm in thickness were analyzed in increments of 0.1mm to understand how these attributes affect the quality and print time of the parts and isolate specific dimensions which are optimized for the FDM process. The results revealed optimized zones where the outer wall, inner wall/s, and/or infill are produced as continuous extrusions significantly faster to print than thicknesses falling outside of optimized zones. As a result, a quick reference graph and several equations are presented based on fundamental FDM principles, allowing design engineers to implement optimized wall dimensions in computer-aided design (CAD) rather than leaving print optimization to technicians and manufacturers in the final process parameters.

Fabrication of Biomimetic Scaffolds With Well-Defined Pore Geometry by Fused Deposition Modeling

2007 ◽  
Author(s):  
Esmaiel Jabbari ◽  
David N. Rocheleau ◽  
Weijie Xu ◽  
Xuezhong He
Keyword(s):  
Computer Aided Design ◽  
Fused Deposition Modeling ◽  
Pore Geometry ◽  
Micro Computed Tomography ◽  
Fused Deposition ◽  
Biomimetic Scaffolds ◽  
Orthogonal Geometry ◽  
Deposition Modeling ◽  
Functional Peptides ◽  
Homogeneous Formation

It is well established that the pore size and distribution affect the rate of cell migration and the extent of extracellular matrix formation. The objective of this work was to develop a process for fabrication of biodegradable and shape-specific polymeric scaffolds with well-defined pore geometry, functionalized with covalently attached bioactive peptides, for applications in tissue regeneration. We have used the Fused Deposition Modeling (FDM) RP technology to fabricate degradable and functional scaffolds with well-defined pore geometry. Computer aided design (CAD) using SolidWorks was used to create models of the cubic orthogonal geometry. The models were used to create the machine codes necessary to build the scaffolds with FDM with wax as the build material. A novel biodegradable in-situ crosslinkable macromer, poly(lactide-co-glycolide fumarate) or PLGF, mixed with reactive functional peptides was infused in the scaffold and allowed to crosslink. The scaffold was then immersed in a hydrocarbon solvent to remove the wax, leaving just the PLGF behind as the support material dissolved. The pore morphology of the PLGF scaffold was imaged with micro-computed tomography and scanning electron microscopy. Cellular function in the PLFG scaffolds with well-defined pore geometry was studied with bone marrow stromal cells isolated from rats. Results demonstrate that the scaffolds support homogeneous formation of mineralized tissue.

Sign in / Sign up

Export Citation Format

Share Document