Simulation of Optimizing the Partial Load Performance of a Gas Turbine Combined Cycle Using Exhaust Heat Recuperation and Inlet Bleed Heating

2020 ◽  
Author(s):  
Seong Won Moon ◽  
Tong Seop Kim
Keyword(s):  
Gas Turbine ◽  
Combined Cycle ◽  
Inlet Guide Vane ◽  
Inlet Temperature ◽  
Operating Range ◽  
Cycle Simulation ◽  
Partial Load ◽  
Exhaust Heat ◽  
Load Regime ◽  
Heat Recuperation

Abstract This paper proposes a novel method to extend the operating range and improve the partial load efficiency of the gas turbine combined cycle (GTCC). The combination of exhaust heat recuperation and inlet bleed heating (IBH) was evaluated through a cycle simulation. The degree of heat recuperation was modulated during partial load operation to enhance the cycle efficiency. The recuperation ratio was modulated before control of the variable inlet guide vane (VIGV) began. This means that the recuperation control covers the high partial load regime. The gas turbine power remained almost constant in this regime because the inlet flow rate and turbine inlet temperature were kept constant. In contrast, the power of the bottoming cycle decreased with increasing recuperation ratio due to the decrease in exhaust gas energy. After the recuperation ratio reached a limit, the load control was the same, as in conventional plants: VIGV control followed by fuel only control. The purpose of using IBH was to reduce CO emissions in the low load regime. Some of the compressor discharge air was recirculated to the compressor inlet, and the combustion temperature was maintained at a high level. Both IBH and recuperation were effective in extending the operating range. The turndown ratio was predicted to decrease by approximately 10%p. The efficiency remained higher than the full load efficiency over a wide partial load range. The efficiency of the recuperated GTCC was 4.1%p higher at 50% power than that of the conventional GTCC.

Simulation of Optimizing the Partial Load Performance of a Gas Turbine Combined Cycle Using Exhaust Heat Recuperation and Inlet Bleed Heating

2020 ◽  
Author(s):  
Seong Won Moon ◽  
Tong Seop Kim
Keyword(s):  
Gas Turbine ◽  
Combined Cycle ◽  
Inlet Guide Vane ◽  
Inlet Temperature ◽  
Operating Range ◽  
Cycle Simulation ◽  
Partial Load ◽  
Exhaust Heat ◽  
Load Regime ◽  
Heat Recuperation

Abstract Extending the operating range and improving the partial load efficiency of the gas turbine combined cycle (GTCC) is becoming increasingly important. This paper proposes a novel method to achieve the two goals simultaneously. To fulfill the research objective, the combination of exhaust heat recuperation and inlet bleed heating (IBH) was adopted and evaluated. A cycle simulation was conducted to confirm whether the research goal could be achieved. A recuperator was installed between the compressor and combustor of the gas turbine, and the degree of heat recuperation was modulated during partial load operation to enhance the cycle efficiency compared to the conventional GTCC plant. In contrast to the conventional GTCC plant, the recuperation ratio was modulated before control of the variable inlet guide vane (VIGV) began. This means that the recuperation control covers the high partial load regime. The gas turbine power remained almost constant in this regime because the inlet flow rate and turbine inlet temperature were kept constant. In contrast, the power of the bottoming cycle decreased with increasing recuperation ratio due to the decrease in exhaust gas energy. After the recuperation ratio reached a limit, the load control was the same, as in conventional plants: VIGV control followed by fuel only control. The purpose of using IBH was to reduce CO emissions in the low load regime. Some of the compressor discharge air was recirculated to the compressor inlet, and the combustion temperature was maintained at a high level. The simulation showed that both IBH and recuperation are effective in extending the operating range. The predicted reduction in the turndown ratio was approximately 10%p. The partial load efficiency improvement by the recuperation was sensible. The efficiency remained higher than the full load efficiency over a wide partial load range. The efficiency of the recuperated GTCC was 4.1%p higher at 50% power than that of the conventional GTCC.

Conceptual Recovery of Exhaust Heat From a Conventional Gas Turbine by an Inter-Cooled Inverted Brayton Cycle

1999 ◽  
Author(s):  
Y. Tsujikawa ◽  
K. Ohtani ◽  
K. Kaneko ◽  
T. Watanabe ◽  
S. Fujii
Keyword(s):  
Gas Turbine ◽  
Heat Recovery ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Brayton Cycle ◽  
Turbine Performance ◽  
Exhaust Heat ◽  
Manufacturing Techniques ◽  
Industrial Gas Turbine ◽  
Made In

Improvements in industrial gas turbine performance have been made in last decade. Advances in the gas turbine technologies such as higher turbine inlet temperature, materials, and manufacturing techniques justify the development of new combined or cogeneration cycle schemes, with more advance heat recovery capabilities. This paper describes the performance analysis of an Inverted Brayton Heat Recovery (IBHR) cycle, which is combined with conventional gas turbine and worked as a bottoming cycle. The optimum characteristics have been calculated and it is shown that this cycle is superior to the conventional combined cycle and cogeneration systems in terms of thermal efficiency and specific output. The main feature of this new concept is that the inverted Brayton cycle with inter-cooling is introduced. Further, a new estimating function, “the emission coefficient of carbon-dioxide” has been successfully introduced to assess the environmental compatibility.

Part-Load Operation of Gas Turbines Induced by Co-Gasification of Coal and Biomass in an Integrated Gasification Combined Cycle Power Plant

2021 ◽  
Author(s):  
Silvia Ravelli
Keyword(s):  
Power Plant ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Inlet Guide Vane ◽  
Inlet Temperature ◽  
Fuel Quality ◽  
Integrated Gasification Combined Cycle ◽  
Part Load ◽  
Wide Range ◽  
Integrated Gasification

Abstract This study takes inspiration from a previous work focused on the simulations of the Willem-Alexander Centrale (WAC) power plant located in Buggenum (the Netherlands), based on integrated gasification combined cycle (IGCC) technology, under both design and off-design conditions. These latter included co-gasification of coal and biomass, in proportions of 30:70, in three different fuel mixtures. Any drop in the energy content of the coal/biomass blend, with respect to 100% coal, translated into a reduction in gas turbine (GT) firing temperature and load, according to the guidelines of WAC testing. Since the model was found to be accurate in comparison with operational data, here attention is drawn to the GT behavior. Hence part load strategies, such as fuel-only turbine inlet temperature (TIT) control and inlet guide vane (IGV) control, were investigated with the aim of maximizing the net electric efficiency (ηel) of the whole plant. This was done for different GT models from leading manufactures on a comparable size, in the range between 190–200 MW. The influence of fuel quality on overall ηel was discussed for three binary blends, over a wide range of lower heating value (LHV), while ensuring a concentration of H2 in the syngas below the limit of 30 vol%. IGV control was found to deliver the highest IGCC ηel combined with the lowest CO2 emission intensity, when compared not only to TIT control but also to turbine exhaust temperature control, which matches the spec for the selected GT engine. Thermoflex® was used to compute mass and energy balances in a steady environment thus neglecting dynamic aspects.

Three Spool High Efficiency Small Scale Gas Turbine Concept

2017 ◽  
Author(s):  
Matti Malkamäki ◽  
Ahti Jaatinen-Värri ◽  
Antti Uusitalo ◽  
Aki Grönman ◽  
Juha Honkatukia ◽  
...  
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Efficiency ◽  
Small Scale ◽  
Inlet Temperature ◽  
Substantial Impact ◽  
Electrical Efficiency ◽  
Partial Load ◽  
Reciprocating Engines

Decentralized electricity and heat production is a rising trend in small-scale industry. There is a tendency towards more distributed power generation. The decentralized power generation is also pushed forward by the policymakers. Reciprocating engines and gas turbines have an essential role in the global decentralized energy markets and improvements in their electrical efficiency have a substantial impact from the environmental and economic viewpoints. This paper introduces an intercooled and recuperated three stage, three-shaft gas turbine concept in 850 kW electric output range. The gas turbine is optimized for a realistic combination of the turbomachinery efficiencies, the turbine inlet temperature, the compressor specific speeds, the recuperation rate and the pressure ratio. The new gas turbine design is a natural development of the earlier two-spool gas turbine construction and it competes with the efficiencies achieved both with similar size reciprocating engines and large industrial gas turbines used in heat and power generation all over the world and manufactured in large production series. This paper presents a small-scale gas turbine process, which has a simulated electrical efficiency of 48% as well as thermal efficiency of 51% and can compete with reciprocating engines in terms of electrical efficiency at nominal and partial load conditions.

Advanced and Transformational Hydrogen Turbines for Integrated Gasification Combined Cycles

2016 ◽  
Author(s):  
Walter W. Shelton ◽  
Robin W. Ames ◽  
Richard A. Dennis ◽  
Charles W. White ◽  
John E. Plunkett ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Carbon Capture ◽  
Combined Cycle ◽  
Plant Performance ◽  
System Level ◽  
Inlet Temperature ◽  
Air Cooling ◽  
Reference Case ◽  
Advanced Technologies ◽  
Integrated Gasification

The U.S. Department of Energy’s (DOE) provides a worldwide leadership role in the development of advanced fossil fuel-based energy conversion technologies, with a focus on electric power generation with carbon capture and storage (CCS). As part of DOE’s Office of Fossil Energy, the National Energy Technology Laboratory (NETL) implements research, development, and demonstration (RD&D) programs that address the challenges of reducing greenhouse gas emissions. To meet these challenges, NETL evaluates advanced power cycles that will maximize system efficiency and performance, while minimizing CO2 emissions and the costs of CCS. NETL’s Hydrogen Turbine Program has sponsored numerous R&D projects in support of Advanced Hydrogen Turbines (AHT). Turbine systems and components targeted for development include combustor technology, materials research, enhanced cooling technology, coatings development, and more. The R&D builds on existing gas turbine technologies and is intended to develop and test the component technologies and subsystems needed to validate the ability to meet the Turbine Program goals. These technologies are key components of AHTs, which enable overall plant efficiency and cost of electricity (COE) improvements relative to an F-frame turbine-based Integrated Gasification Combined Cycle (IGCC) reference plant equipped with carbon capture (today’s state-of-the-art). This work has also provided the basis for estimating future IGCC plant performance based on a Transformational Hydrogen Turbine (THT) with a higher turbine inlet temperature, enhanced material capabilities, reduced air cooling and leakage, and higher pressure ratios than the AHT. IGCC cases from using system-level AHT and THT gas turbine models were developed for comparisons with an F-frame turbine-based IGCC reference case and for an IGCC pathway study. The IGCC pathway is presented in which the reference case (i.e. includes F-frame turbine) is sequentially-modified through the incorporation of advanced technologies. Advanced technologies are considered to be either 2nd Generation or Transformational, if they are anticipated to be ready for demonstration by 2025 and 2030, respectively. The current results included the THT, additional potential transformational technologies related to IGCC plant sections (e.g. air separation, gasification, gas cleanup, carbon capture, NOx reduction) are being considered by NETL and are topics for inclusion in future reports.

scholarly journals High-Temperature Turbine Technology Readiness

1982 ◽  
Author(s):  
M. W. Horner ◽  
A. Caruvana
Keyword(s):  
High Temperature ◽  
Gas Turbine ◽  
Phase Ii ◽  
Combined Cycle ◽  
Technology Readiness ◽  
Inlet Temperature ◽  
Test Results ◽  
Turbine Inlet ◽  
Combined Cycle Plant ◽  
Gas Fuel

Final component and technology verification tests have been completed for application to a 2600°F rotor inlet temperature gas turbine. These tests have proven the capability of combustor, turbine hot section, and IGCC fuel systems and controls to operate in a combined cycle plant burning a coal-derived gas fuel at elevated gas turbine inlet temperatures (2600–3000°F). This paper presents recent test results and summarizes the overall progress made during the DOE-HTTT Phase II program.

Analysis of Intermediate Temperature Combined Cycles With a Carbon Dioxide Topping Cycle

2008 ◽  
Author(s):  
R. Chacartegui ◽  
D. Sa´nchez ◽  
F. Jime´nez-Espadafor ◽  
A. Mun˜oz ◽  
T. Sa´nchez
Keyword(s):  
Carbon Dioxide ◽  
Power Plant ◽  
Gas Turbine ◽  
High Efficiency ◽  
Solar Power ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Pressure Drops ◽  
Combined Cycles ◽  
Topping Cycle

The development of high efficiency solar power plants based on gas turbine technology presents two problems, both of them directly associated with the solar power plant receiver design and the power plant size: lower turbine intake temperature and higher pressure drops in heat exchangers than in a conventional gas turbine. To partially solve these problems, different configurations of combined cycles composed of a closed cycle carbon dioxide gas turbine as topping cycle have been analyzed. The main advantage of the Brayton carbon dioxide cycle is its high net shaft work to expansion work ratio, in the range of 0.7–0.85 at supercritical compressor intake pressures, which is very close to that of the Rankine cycle. This feature will reduce the negative effects of pressure drops and will be also very interesting for cycles with moderate turbine inlet temperature (800–1000 K). Intercooling and reheat options are also considered. Furthermore, different working fluids have been analyzed for the bottoming cycle, seeking the best performance of the combined cycle in the ranges of temperatures considered.

Effect of Coolant Injection Angle on Nozzle Endwall Film Cooling: Experimental and Numerical Analysis in Linear Cascade

2018 ◽  
Author(s):  
Lamyaa El-Gabry ◽  
Hongzhou Xu ◽  
Kevin Liu ◽  
James Chang ◽  
Michael Fox
Keyword(s):  
Flow Field ◽  
Gas Turbine ◽  
Surface Film ◽  
Combined Cycle ◽  
Gas Temperature ◽  
Injection Angle ◽  
Linear Cascade ◽  
Cfd Models ◽  
Coolant Injection ◽  
Exhaust Heat

Gas turbine components can withstand gas temperatures exceeding the melting point of the alloys they’re made of due to increasingly effective cooling methods. Increasing the operating temperature of a gas turbine is key to improving its power density and exhaust heat for steam or combined-cycle efficiency. In the turbine, the component that experiences the highest gas temperature is the vane directly downstream of the combustor; the most complex flow field in a vane occurs near the endwall. In this study, an experimental investigation is carried out to determine the effect of coolant injection angle and mass flow ratio on film effectiveness on the endwall using the pressure sensitive paint technique for various configurations of jump cooling hole configurations. Two rows of angled holes are upstream of an uncooled vane in a three-vane linear cascade. Injection angle including compound angle is varied from 20 to 60 and coolant to mainstream massflux ratio is varied from 0.5% to 3%. Contours of endwall surface film effectiveness are presented along with span-averaged film effectiveness. CFD models of the cascade are developed using a commercial solver to predict film effectiveness for some of the test conditions and comparisons are made between the experimental and numerical results. The CFD models provide further insight into the flow field and explain trends observed in the experiment by understanding the interaction of jump coolant flow with the 3D endwall mainstream flows.

Application of Ultra-Low NOx Combustor to the MHPS Existing Gas Turbine

2021 ◽  
Author(s):  
Takashi Nishiumi ◽  
Hirofumi Ohara ◽  
Kotaro Miyauchi ◽  
Sosuke Nakamura ◽  
Toshishige Ai ◽  
...  
Keyword(s):  
High Pressure ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Operational Experience ◽  
Emission Rates ◽  
Gas Temperature ◽  
Design Development ◽  
And Control

Abstract In recent years, MHPS achieved a NET M501J gas turbine combined cycle (GTCC) efficiency in excess of 62% operating at 1,600°C, while maintaining NOx under 25ppm. Taking advantage of our gas turbine combustion design, development and operational experience, retrofits of earlier generation gas turbines have been successfully applied and will be described in this paper. One example of the latest J-Series technologies, a conventional pilot nozzle was changed to a premix type pilot nozzle for low emission. The technology was retrofitted to the existing F-Series gas turbines, which resulted in emission rates of lower than 9ppm NOx(15%O2) while maintaining the same Turbine Inlet Temperature (TIT: Average Gas Temperature at the exit of the transition piece). After performing retrofitting design, high pressure rig tests, the field test prior to commercial operation was conducted on January 2019. This paper describes the Ultra-Low NOx combustor design features, retrofit design, high pressure rig test and verification test results of the upgraded M501F gas turbine. In addition, it describes another upgrade of turbine to improve efficiency and of combustion control system to achieve low emissions. Furthermore it describes the trouble-free upgrade of seven (7) units, which was completed by utilizing MHPS integration capabilities, including handling all the design, construction and service work of the main equipment, plant and control systems.

Sign in / Sign up

Export Citation Format

Share Document