On the Limit of Surface Integrity of Alumina by Ductile-Mode Grinding

1999 ◽  
Vol 122 (1) ◽  
pp. 129-134 ◽  
Author(s):  
I. Zarudi ◽  
L. C. Zhang
Keyword(s):  
Surface Integrity ◽  
Bulk Material ◽  
Material Surface ◽  
Grinding Wheel ◽  
Mirror Surface ◽  
Abrasive Grains ◽  
Pit Formation ◽  
Ductile Mode ◽  
Grinding Conditions ◽  
Radial Cracks

This paper investigates both experimentally and theoretically the subsurface damage in alumina by ductile-mode griding. It found that the distribution of the fractured area on a ground mirror surface, with the Rms roughness in the range from 30 nm to 90 nm, depends on not only the grinding conditions but also the pores in the bulk material. Surface pit formation is the result of interaction of abrasive grains of the grinding wheel with pores. Thus the surface quality achievable by ductile-mode grinding is limited by the initial microstructure of a material. The investigation shows that median and radial cracks do not appear and hence are not the cause of fracture as usually thought. [S0094-4289(00)02001-6]

High Efficient Mechanism of Material Removal in Two-Dimensional Ultrasonic Grinding from the Locus Perspective

2009 ◽  
Vol 416 ◽  
pp. 609-613
Author(s):  
Ming Li Zhao ◽  
Bo Zhao ◽  
Yu Qing Wang ◽  
Guo Fu Gao
Keyword(s):  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Material Surface ◽  
Grinding Wheel ◽  
Two Dimensional ◽  
Abrasive Grains ◽  
Ultrasonic Grinding ◽  
High Efficient

Relative motion of single abrasive is analyzed for the different applied directions of longitudinal ultrasonic vibration, and its locus is simulated in the present paper. The research results show that the locus in two-dimensional ultrasonic vibration is only similar to that in y-direction, and both are close to sinusoid curves. The width of grooves scratched by abrasive grains y-direction (axial direction of grinding wheel) is two times of the vibration amplitude, and the material removal rate increases remarkably. In case of x-direction (tangential direction of grinding wheel) ultrasonic vibration, abrasive grains with periodic force impact material surface with high frequency vibration, which make material fracture removal easy. Therefore, the high efficiency essence of material removal in two-dimensional ultrasonic grinding is revealed in view of locus. In addition, according to the results of grinding experiments, under same conditions good surface quality can be obtained in two-dimensional ultrasonic grinding and material removal rate in common grinding is the lowest. Consequently it is further proved that the method of two-dimensional ultrasonic vibration grinding is an effective one for ceramic materials.

Study on Edge Contact Area and Surface Integrity of Workpiece in Point Grinding Process

2009 ◽  
Vol 407-408 ◽  
pp. 577-581
Author(s):  
Shi Chao Xiu ◽  
Zhi Jie Geng ◽  
Guang Qi Cai
Keyword(s):  
Surface Integrity ◽  
Contact Area ◽  
High Speed ◽  
Ground Surface ◽  
Depth Of Cut ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Edge Contact ◽  
Cylindrical Grinding ◽  
Theoretic Foundations

During cylindrical grinding process, the geometric configuration and size of the edge contact area between the grinding wheel and workpiece have the heavy effects on the workpiece surface integrity. In consideration of the differences between the point grinding and the conventional high speed cylindrical grinding, the geometric and mathematic models of the edge contact area in point grinding were established. Based on the models, the numerical simulation for the edge contact area was performed. By means of the point grinding experiment, the effect mechanism of the edge contact area on the ground surface integrity was investigated. These will offer the applied theoretic foundations for optimizing the point grinding angles, depth of cut, wheel and workpiece speed, geometrical configuration and size of CBN wheel and some other grinding parameters in point grinding process.

Surface integrity of quenched steel 1045 machined by CBN grinding wheel and SiC grinding wheel

2017 ◽  
Vol 8 (2) ◽  
pp. 179-187 ◽  
Author(s):  
Kankan Ji ◽  
Xingquan Zhang ◽  
Shubao Yang ◽  
Liping Shi ◽  
Shiyi Wang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Morphology ◽  
Compressive Stress ◽  
Surface Integrity ◽  
Grinding Wheel ◽  
Micro Hardness ◽  
Content Type ◽  
Quenched Steel ◽  
Cut Depth ◽  
Cbn Grinding Wheel

Purpose The purpose of this paper is to evaluate surface integrity of quenched steel 1045 ground drily by the brazed cubic boron nitride (CBN) grinding wheel and the black SiC wheel, respectively. Surface integrity, including surface roughness, sub-surface hardness, residual stresses and surface morphology, was investigated in detail, and the surface quality of samples ground by two grinding wheels was compared. Design/methodology/approach In the present work, surface integrity of quenched steel 1045 machined by the CBN grinding wheel and the SiC wheel was investigated systematically. All the specimens were machined with a single pass in the down-cutting mode of dry condition. Surface morphology of the ground specimen was observed by using OLYMPUS BX51M optical microscopy. Surface roughness of seven points was measured by using a surface roughness tester at a cut-off length of 1.8 mm and the measurement traces were perpendicular to the grinding direction. Sub-surface micro-hardness was measured by using HVS-1000 digital micro-hardness tester after the cross-section surface was polished. The residual stress was tested by using X-350A X-ray stress analyzer. Findings When the cut depth is increased from 0.01 to 0.07 mm, the steel surface machined by the CBN wheel remains clear grinding mark, lower roughness, higher micro-hardness and higher magnitude of compressive stress and fine microstructure, while the surface machined by the SiC grinding wheel becomes worse with increasing of cut depth. The value of micro-hardness decreases, and the surface roughness increases, and the surface compressive stress turns into tensile stress. Some micro-cracks and voids occur when the sample is processed by the SiC grinding wheel with cut depth 0.07 mm. Originality/value In this paper, the specimens of quenched steel 1045 were machined by the CBN grinding wheel and the SiC wheel with various cutting depths. The processing quality resulted from the CBN grinding wheel is better than that resulted from the SiC grinding wheel.

Methodology for Evaluation of Treated Steels and Alloys in Abrasive Processing

2021 ◽  
Vol 410 ◽  
pp. 262-268
Author(s):  
Vyacheslav M. Shumyacher ◽  
Sergey A. Kryukov ◽  
Natal'ya V. Baidakova
Keyword(s):  
Physical And Mechanical Properties ◽  
Metals And Alloys ◽  
Grinding Wheel ◽  
Measuring Instruments ◽  
Abrasive Machining ◽  
Machining Performance ◽  
Abrasive Grains ◽  
Abrasive Tools ◽  
Composition Structure ◽  
Grinding Operations

One of the critical physical and mechanical properties of metals and alloys is the suitability for abrasive machining. Machining by abrasive tools is the final operation that sets the desired macro-geometry parameters of processed blanks and microgeometry parameters of processed surfaces such as roughness and length of a bearing surface. Abrasive machining determines the most important physical and mechanical parameters of a blank surface layer, i.e. stresses, phase composition, structure. Machinability by abrasive tools depends on the machining performance affected both by the blank material properties and various processing factors. In our previous studies, we proved that during abrasive machining the metal microvolume affected by abrasive grains accumulates energy. This energy is used for metal dispersion and is converted into heat. According to the theoretical studies described herein, one may note the absence of a reliable and scientifically valid method as well as measuring instruments to determine the machinability of metals and alloys by abrasive tools. For this reason, we suggested a method simulating the effect the multiple abrasive grains produce in a grinding wheel, and enabling us to identify machinability of metals and alloys, select the most efficient abrasive materials for machining of the same, and form the basis for development of effective grinding operations.

Einfluss der Abrichtgrößen beim Schleifen*/Influence of dressing parameters on the grinding process - Systematic research of dressing parameters on workpiece roughness and surface integrity

2016 ◽  
Vol 106 (01-02) ◽  
pp. 44-50
Author(s):  
T. Lierse ◽  
B. Karpuschewski ◽  
T. R. Kaul
Keyword(s):  
Aluminum Oxide ◽  
Surface Integrity ◽  
Cvd Diamond ◽  
Grinding Wheel ◽  
Systematic Research ◽  
Grinding Process ◽  
Wheel Topography ◽  
Grinding Wheel Topography

Dieser Beitrag zeigt, dass die durch die Abrichtparameter erzeugte Schleifscheibentopographie nicht nur die Oberflächengüte des Werkstücks, sondern auch dessen Eigenspannungszustand in der Werkstückrandzone in weiten Grenzen verändert. Die Untersuchungen zum Abrichten von Korundschleifscheiben mit einer CVD-Diamantformrolle stellen den Zusammenhang zwischen dem Abrichten unterschiedlicher Schleifscheiben zur Bauteilqualität in Form der Oberflächenrautiefe und randzonennahen Eigenspannungen her.   The quality of the workpiece rim is changed by every grinding process. The grinding wheel topography created by the dressing process has not only influence on the workpiece roughness but also on the surface integrity. The pointed research using aluminum oxide abrasive wheels dressed by CVD diamond dressing discs shows a correlation between the dressing parameters, the workpiece roughness and the surface integrity.

Ultra-High Speed Grinding Using a CBN Wheel for a Mirror-Like Surface Finish

2005 ◽  
Vol 291-292 ◽  
pp. 67-72 ◽  
Author(s):  
M. Ota ◽  
T. Nakayama ◽  
K. Takashima ◽  
H. Watanabe
Keyword(s):  
Surface Finish ◽  
High Speed ◽  
High Efficiency ◽  
Ground Surface ◽  
Machining Process ◽  
Grinding Wheel ◽  
Cbn Wheel ◽  
Ultra High Speed ◽  
High Speed Grinding ◽  
Grinding Conditions

There are strong demands for a machining process capable of reducing the surface roughness of sliding parts, such as auto parts and other components, with high efficiency. In this work, we attempted to grind hardened steel to a mirror-like surface finish with high efficiency using an ultra-high speed grinding process. In the present study, we examined the effects of the work speed and the grinding wheel grain size in an effort to optimize the grinding conditions for accomplishing mirror-like surface grinding with high efficiency. The results showed that increasing the work speed, while keeping grinding efficiency constant, was effective in reducing the work affected layer and that the grinding force of a #200 CBN wheel was lower than that of a #80 CBN wheel. Based on these results, a high-efficiency grinding step with optimized grinding conditions was selected that achieved excellent ground surface quality with a mirror-like finish.

scholarly journals The enhancement of cutting capacity of a grinding wheel when processing ductile steel blank parts by ultrasonic activation

2021 ◽  
pp. 55-62
Author(s):  
A. V. Khazov ◽  
◽  
A. N. Unyanin ◽  
Keyword(s):  
Numerical Simulation ◽  
Grinding Wheel ◽  
Ultrasonic Vibrations ◽  
Ultrasonic Activation ◽  
Workpiece Material ◽  
Steel Blank ◽  
Micro Cutting ◽  
Abrasive Grains ◽  
Junction Points ◽  
Cutting Capacity

The study aimed to identify the relations between the sticking intensity and ultrasonic vibrations (UV) used for processing and evaluate the wheels’ performance when grinding ductile materials blank parts. The authors carried out the numerical simulation of local temperatures and the 3H3M3F steel workpiece temperature when grinding by ultrasonic activation. The study determined that the application of ultrasonic vibrations with the amplitude of 3 µm causes the decrease in local temperatures by 13…40 %, and in blank part temperature – up to 20 %. The calculation identified that the activation of ultrasonic vibrations with the amplitude of 3 µm causes the decrease in the glazing coefficient by 33 % for cutting grain and by 7 % for deforming grain. When increasing the longitudinal feed rate or the grinding depth, the glazing coefficient increases to a lesser degree when using the ultrasonic vibration than in the case without ultrasonic activation. The authors carried out the numerical simulation of local temperatures when scratching the 3H3M3F steel specimens by single abrasive grains with ultrasonic activation. The sticking deformation and the stresses resulted from this deformation and affecting the junction points of sticking with grains with and without ultrasonic vibrations application are calculated. The experimental research included the micro-cutting of specimens with single abrasive grains. The experiments identified that the abrasive grains wear out and glaze to a lesser degree when micro-cutting a workpiece with ultrasonic vibrations activation. The lowering of the intensity of sticking of the workpiece material particles to the abrasive grains due to the adhesion causes the decrease in the glazing coefficient when using ultrasonic activation. The study considered the possibility to enhance the efficiency of flat grinding through the use of the energy of ultrasonic vibrations applied to a blank part in the direction with the grinding wheel axis. A workpiece fixed in the device between the vibration transducer and the support is one of the components of a vibration system. The authors performed the experiment when grinding 3H3M3F and 12H18N10T steel workpieces with the wheel face. When grinding with ultrasonic vibrations, the grinding coefficient increases up to 70 %, and the redress life increases twice or thrice.

COMPARISON OF EXPERIMENTALLY MEASURED AND SIMULATED WORKPIECE AND GRINDING WHEEL TOPOGRAPHY USING A NEW DRESSING MODEL

2016 ◽  
Vol 40 (1) ◽  
pp. 1-17 ◽  
Author(s):  
Abdalslam Darafon ◽  
Andrew Warkentin ◽  
Robert Bauer
Keyword(s):  
Surface Finish ◽  
Metal Removal ◽  
Ground Surface ◽  
Cutting Edge ◽  
Edge Density ◽  
Grinding Wheel ◽  
Workpiece Surface ◽  
Wheel Topography ◽  
Grinding Wheel Topography ◽  
Grinding Conditions

This paper presents a new empirical model of the dressing process in grinding which is then incorporated into a 3D metal removal computer simulator to numerically predict the ground surface of a workpiece as well as the dressed surface of the grinding wheel. The proposed model superimposes a ductile cutting dressing model with a grain fracture model to numerically generate the resulting grinding wheel topography and workpiece surface. Grinding experiments were carried out using “fine”, “medium” and “coarse” dressing conditions to validate both the predicted wheel topography as well as the workpiece surface finish. For the grinding conditions used in this research, it was observed that the proposed dressing model is able to accurately predict the resulting workpiece surface finish for all dressing conditions tested. Furthermore, similar trends were observed between the predicted and experimentally-measured grinding wheel topographies when plotting the cutting edge density, average cutting edge width and average cutting edge spacing as a function of depth for all dressing conditions tested.

Forming Mechanism of Composite Abrasive Grains in Oxide Film on ELID Wheel and its Microstructure

2016 ◽  
Vol 709 ◽  
pp. 77-81 ◽  
Author(s):  
Ji Cai Kuai ◽  
Cheng Ran Jiang ◽  
Jiang Wei Wang
Keyword(s):  
Oxide Film ◽  
Grinding Wheel ◽  
Compound Structure ◽  
Wheel Surface ◽  
Forming Mechanism ◽  
Elid Grinding ◽  
Abrasive Grains ◽  
Shaped Crack

In this paper we analyze the forming mechanism of composite abrasive grains in oxide film on ELID grinding wheel surface, By using composition information and by taking advantage of microscale structure, we have investigated that abrasive grains surface is covered by a layer of oxide film and the fresh oxide film is loose and porous like turtle shaped crack when crushed and dried. The elements of oxide film consist of α-Fe2O3 with sphere grain of 5-50nm. This phenomena is demonstrated that the composite abrasive grains in oxide film is a compound structure which is centered by abrasive grains, with α-Fe2O3,Fe (OH)3 surrounded.

Surface Integrity of Biodegradable Magnesium-Calcium (Mg-Ca) Alloy by Low Plasticity Burnishing

2010 ◽  
Author(s):  
M. Salahshoor ◽  
Y. B. Guo
Keyword(s):  
Surface Roughness ◽  
Residual Stresses ◽  
Surface Integrity ◽  
Bulk Material ◽  
Large Diameter ◽  
Biological Response ◽  
The Body ◽  
Low Plasticity Burnishing ◽  
Sever Plastic Deformation ◽  
Biodegradable Magnesium

When a device is implanted into the body, into either hard or soft tissue, the body will respond. While the bulk material of the device is often important for integrity and mechanical success, the device surface is at the interface with biology. Major effort has been spent modifying a biomaterial surface in order to elicit or inhibit a biological response. Metallic biodegradable Magnesium-Calcium (Mg-Ca) alloys have attracted an increased attention for orthopedic fixation applications. This research focuses on low plasticity burnishing (LPB) as a novel surface modification technique that is added to the surface to control biodegradation as a biological response. The effects of burnishing pressure as an important process parameter on surface integrity characteristics such as surface roughness, surface topography, and residual stresses are investigated. Burnished surface roughness is smaller than the machined ones. However, some amount of waviness is observed which might be due to large diameter of the burnishing ball and sever plastic deformation. High compressive residual stresses are measured on the burnished surface.

Sign in / Sign up

Export Citation Format

Share Document