scholarly journals Rapid Calculation of Engine Performance

1985 ◽  
Author(s):  
Zhang Jin ◽  
Zhu Xinjian
Keyword(s):  
Working Conditions ◽  
Statistical Data ◽  
Engine Performance ◽  
Calculation Procedure ◽  
Turbofan Engine ◽  
Design Performance ◽  
Engine Design ◽  
Rapid Calculation ◽  
Performance Calculation ◽  
Preliminary Phase

A rapid calculation procedure for design and off-design performance of turbojet and turbofan engine is developed. It peculiarity is that the general characteristics of components are established based on statistical data and the engine working conditions are searched according to matching of these general characteristics. This method can be used to select cycle parameters in engine design, and has been employed in engine performance calculation program used in the preliminary phase of engine design or airframe/engine integration design.

Gas Turbine Off-Design Performance Adaptation Using a Genetic Algorithm

2006 ◽  
Author(s):  
E. Lo Gatto ◽  
Y. G. Li ◽  
P. Pilidis
Keyword(s):  
Genetic Algorithm ◽  
Gas Turbine ◽  
Performance Prediction ◽  
Engine Performance ◽  
Design Data ◽  
Adaptive Approach ◽  
Design Point ◽  
Design Performance ◽  
Engine Design ◽  
Performance Adaptation

Gas turbine gas path diagnostics is heavily dependent on performance simulation models accurate enough around a chosen diagnostic operating point, such as design operating point. With current technology, gas turbine engine performance can be predicted easily with thermodynamic models and computer codes together with basic engine design data and empirical component information. However the accuracy of the prediction is highly dependent on the quality of those engine design data and empirical component information such as component characteristic maps but such expensive information is normally exclusive property of engine manufacturers and only partially disclosed to engine users. Alternatively, estimated design data and assumed component information are used in the performance prediction. Yet, such assumed component information may not be the same as those of real engines and therefore poor off-design performance prediction may be produced. This paper presents an adaptive method to improve the accuracy of off-design performance prediction of engine models near engine design point or other points where detailed knowledge is available. A novel definition of off-design scaling factors for the modification of compressor maps is developed. A Genetic Algorithm is used to search the best set of scaling factors in order to adapt the predicted off-design engine performance to observed engine off-design performance. As the outcome of the procedure, new compressor maps are produced and more accurate prediction of off-design performance is provided. The proposed off-design performance adaptation procedure is applied to a model civil aero engine to test the effectiveness of the adaptive approach. The results show that the developed adaptive approach, if properly applied, has great potential to improve the accuracy of engine off-design performance prediction in the vicinity of engine design point although it does not guarantee the prediction accuracy in the whole range of off-design conditions. Therefore, such adaptive approach provides an alternative method in producing good engine performance models for gas turbine gas path diagnostic analysis.

Areo-Engine Cycle Parametric Analysis and Installed Performance Calculation Based on Aircraft Flight Mission

2013 ◽  
Vol 482 ◽  
pp. 277-281 ◽  
Author(s):  
Hong Zhou ◽  
Zhan Xue Wang ◽  
Xiao Bo Zhang
Keyword(s):  
Parametric Analysis ◽  
Engine Performance ◽  
Aircraft Engine ◽  
Operating Conditions ◽  
Aircraft Flight ◽  
Performance Requirements ◽  
Engine Design ◽  
Performance Specifications ◽  
Performance Calculation ◽  
Engine Cycle

The aircraft/engine integration design numerical simulation model was established. The engine design performance specifications were obtained by calculating aircraft lift-drag characteristics, mission analysis, constraint analysis. Combining engine cycle parametric analysis with installation loss computing, the engine performance parameters can be found, which meet the aircraft flight envelope performance requirements. Taking double bypass variable cycle engine as an example to check the model, the results show that the variable cycle engine can meet aircrafts thrust and fuel consumption demands under different operating conditions, and achieve cruise thrust adjustment at the same inlet mass flow to reduce installation losses.

Off-Design Performance of an Interstage Turbine Burner Turbofan Engine

2017 ◽  
Vol 139 (8) ◽  
Author(s):  
Feijia Yin ◽  
Arvind G. Rao
Keyword(s):  
Fuel Efficiency ◽  
Cycle Performance ◽  
Inlet Temperature ◽  
Engine Operation ◽  
Turbofan Engine ◽  
Design Performance ◽  
Low Pressure Turbine ◽  
Performance Requirements ◽  
Engine Design ◽  
Operating Points

This paper focuses on the off-design performance of a turbofan engine with an interstage turbine burner (ITB). The ITB is an additional combustion chamber located between the high-pressure turbine (HPT) and the low-pressure turbine (LPT). The incorporation of ITB in an engine can provide several advantages, especially due to the reduction in the HPT inlet temperature and the associated NOx emission reduction. The objective is to evaluate the effects of the ITB on the off-design performance of a turbofan engine. The baseline engine is a contemporary classical turbofan. The effects of the ITB are evaluated on two aspects: first, the influences of an ITB on the engine cycle performance; second, the influences of an ITB on the component characteristics. The dual combustors of an ITB engine provide an extra degree-of-freedom for the engine operation. The analysis shows that a conventional engine has to be oversized to satisfy off-design performance requirement, like the flat rating temperature. However, the application of an ITB eases the restrictions imposed by the off-design performance requirements on the engine design, implying that the off-design performance of an ITB engine can be satisfied without sacrificing the fuel efficiency. Eventually, the performance of the ITB engine exhibits superior characteristics over the baseline engine at the studied operating points over a flight mission.

scholarly journals Axial Compressor Mean-Line Analysis: Choking Modelling and Fully-Coupled Integration in Engine Performance Simulations

2021 ◽  
Vol 6 (1) ◽  
pp. 4
Author(s):  
Ioannis Kolias ◽  
Alexios Alexiou ◽  
Nikolaos Aretakis ◽  
Konstantinos Mathioudakis
Keyword(s):  
Axial Compressor ◽  
Engine Performance ◽  
Engine Model ◽  
Multi Stage ◽  
Transient Simulations ◽  
Full Knowledge ◽  
Compressor Performance ◽  
First Time ◽  
Performance Calculation ◽  
Fully Coupled

A mean-line compressor performance calculation method is presented that covers the entire operating range, including the choked region of the map. It can be directly integrated into overall engine performance models, as it is developed in the same simulation environment. The code materializing the model can inherit the same interfaces, fluid models, and solvers, as the engine cycle model, allowing consistent, transparent, and robust simulations. In order to deal with convergence problems when the compressor operates close to or within the choked operation region, an approach to model choking conditions at blade row and overall compressor level is proposed. The choked portion of the compressor characteristics map is thus numerically established, allowing full knowledge and handling of inter-stage flow conditions. Such choking modelling capabilities are illustrated, for the first time in the open literature, for the case of multi-stage compressors. Integration capabilities of the 1D code within an overall engine model are demonstrated through steady state and transient simulations of a contemporary turbofan layout. Advantages offered by this approach are discussed, while comparison of using alternative approaches for representing compressor performance in overall engine models is discussed.

Probabilistic Analysis of a Turbofan Secondary Flow System

2004 ◽  
Author(s):  
David Cloud ◽  
Ethan Stearns
Keyword(s):  
Secondary Flow ◽  
Probabilistic Analysis ◽  
Flow System ◽  
Engine Performance ◽  
Root Cause ◽  
Engine Design ◽  
Bearing Loads ◽  
Input Variables ◽  
Time Required ◽  
Individual Input

This paper documents a probabilistic analysis of the secondary flow system in a modern commercial turbofan engine. The purpose of this analysis is to investigate the variability in the high and low rotor bearing loads and total secondary flow due to the inherent uncertainty in manufacturing processes and engine performance. In addition to quantifying the variability in bearing load and secondary flow, the sensitivity of the parameters to individual input variables is determined. The system was found to behave linearly, resulting in negligible mean shifts due to input variation. The importance of correlation among the performance parameters will be addressed, as well as the effects of different correlations. Methods used to reduce the time required for the analysis will also be discussed. This type of analysis has many applications in cost reduction, engine design, optimization, and root cause analysis that will be covered in this paper.

Exploring GasTurb 12 for Supplementary Use on an Introductory Propulsion Design Project

2017 ◽  
Author(s):  
Aaron R. Byerley ◽  
Kurt P. Rouser ◽  
Devin O. O’Dowd
Keyword(s):  
System Analysis ◽  
Pressure Ratio ◽  
Supplementary Information ◽  
Design System ◽  
Inlet Temperature ◽  
Turbofan Engine ◽  
Design Project ◽  
Engine Design ◽  
Aeronautical Engineering ◽  
Engine Cycle

The purpose of this paper is to explore GasTurb 12, a commercial gas turbine engine performance simulation program, for supplementary use on an introductory propulsion design project in an undergraduate course. This paper will describe several possible opportunities for supplementing AEDsys (Aircraft Engine Design System Analysis) version 4.012, the engine design software tool currently in use. The project is assigned to juniors taking their first propulsion course in the aeronautical engineering major at the USAF Academy. This course, Aeronautical Engineering 361, which focuses on cycle analysis and selection, is required of all aero majors and is used to satisfy the ABET Program Criterion requiring knowledge of propulsion fundamentals. This paper describes the most recent design project that required the students to re-engine the USAF T-38 with the aim of competing for the Advanced Pilot Training Program (T-X) program. The goal of the T-X program is to replace the T-38 aircraft that entered service in 1961 with an aircraft capable of sustained high-G operations that is also more fuel efficient. The design project required the students to select an engine-cycle for a single, non-afterburning, mixed stream, low bypass turbofan engine to replace the two J85 turbojets currently in the T-38. It was anticipated that the high specific thrust requirements might possibly be met through the use of modern component measures of merit to include a much higher turbine inlet temperature. Additionally, it was anticipated that the required 10% reduction in thrust specific fuel consumption might possibly be achieved by using a turbofan engine cycle with a higher overall pressure ratio. This paper will describe the use of GasTurb 12 to perform the same design analysis that was described above using AEDsys as well as additional features such as numerical optimization, temperature-entropy diagrams, and the generation of scaled, two-dimensional engine geometry drawings. The paper will illustrate how GasTurb 12 offers important supplementary information that will deepen student understanding of engine cycle design and analysis.

Analysis of Effect of Advanced Technique Configurations on Overall Performance of High Bypass Turbofan Engine

2014 ◽  
Author(s):  
Liu Jian Jun
Keyword(s):  
Air Flow ◽  
Engine Performance ◽  
Performance Model ◽  
Direct Drive ◽  
Nozzle Throat ◽  
Advanced Technique ◽  
Turbofan Engine ◽  
Overall Performance ◽  
Cooling Air Flow ◽  
Cooling Air

An analytical study was undertaken using the performance model of a two spool direct drive high BPR 300kN thrust turbofan engine, to investigate the effects of advanced configurations on overall engine performance. These include variable bypass nozzle, variable cooling air flow and more electric technique. For variable bypass nozzle, analysis on performance of outer fan at different conditions indicates that different operating points cannot meet optimal performance at the same time if the bypass nozzle area kept a constant. By changing bypass nozzle throat area at different states, outer fan operating point moves to the location where airflow and efficiency are more appropriate, and have enough margin away from surge line. As a result, the range of variable area of bypass nozzle throat is determined which ensures engine having a low SFC and adequate stability. For variable cooling airflow, configuration of turbine cooling air flow extraction and methodology for obtaining change of cooling airflow are investigated. Then, base on temperature analysis of turbine vane and blade and resistance of cooling airflow, reduction of cooling airflow is determined. Finally, using performance model which considering effect of cooling air flow on work and efficiency of turbine, variable cooling airflow effect on overall performance is analyzed. For more electric technique, the main characteristic is to use power off-take instead of overboard air extraction. Power off-take and air extraction effect on overall performance of high bypass turbofan engine is compared. Investigation demonstrates that power offtake will have less SFC.

Model Based Design and Optimization for Large Bore Engines: Some Industrial Case Studies

2017 ◽  
Author(s):  
Prashant Srinivasan ◽  
Sanketh Bhat ◽  
Manthram Sivasubramaniam ◽  
Ravi Methekar ◽  
Maruthi Devarakonda ◽  
...  
Keyword(s):  
System Design ◽  
Case Studies ◽  
Control Strategy ◽  
Internal Combustion Engines ◽  
Cost Optimization ◽  
Engine Performance ◽  
Design And Optimization ◽  
Model Based ◽  
Performance Requirements ◽  
Engine Design

Large bore reciprocating internal combustion engines are used in a wide variety of applications such as power generation, transportation, gas compression, mechanical drives, and mining. Each application has its own unique requirements that influence the engine design & control strategy. The system architecture & control strategy play a key role in meeting the requirements. Traditionally, control design has come in at a later stage of the development process, when the system design is almost frozen. Furthermore, transient performance requirements have not always been considered adequately at early design stages for large engines, thus limiting achievable controller performance. With rapid advances in engine modeling capability, it has now become possible to accurately simulate engine behavior in steady-states and transients. In this paper, we propose an integrated model-based approach to system design & control of reciprocating engines and outline ideas, processes and real-world case studies for the same. Key benefits of this approach include optimized engine performance in terms of efficiency, transient response, emissions, system and cost optimization, tools to evaluate various concepts before engine build thus leading to significant reduction in development time & cost.

Paper 4: The Effect of Combustion Chamber Shape and Other Engine Design Factors on Exhaust Emissions

1968 ◽  
Vol 183 (5) ◽  
pp. 133-144 ◽  
Author(s):  
P. L. Dartnell ◽  
C. L. Goodacre ◽  
P. V. Lamarque
Keyword(s):  
Combustion Chamber ◽  
Engine Performance ◽  
Exhaust System ◽  
Exhaust Emissions ◽  
Intake Manifold ◽  
Valve Timing ◽  
Mixture Formation ◽  
Engine Design ◽  
Basic Engine ◽  
Design Factors

A Heron combustion chamber engine of 2 litre capacity has been utilized to investigate the effect of combustion chamber shape, increased mixture movement, valve timing, mixture formation, and reaction in the exhaust system on engine performance and level of exhaust emissions using the seven-mode U.S. Federal cycle. Such factors as carburettor weakening and limitation of intake manifold vacuum during overrun have been included in this investigation, and it has been shown that it is possible to reduce exhaust emissions and also satisfy the current U.S. requirements with an engine giving acceptable performance, improved economy, and unaffected reliability. Much of the information reported may be negative in terms of improvement to exhaust emissions by detailed engine design. Nevertheless, some positive conclusions have been reached as a result of this work, and it is hoped that this will draw forth more informed discussion than the authors have been able to assemble from the work attempted with one basic engine.

Sign in / Sign up

Export Citation Format

Share Document