Thermodynamic Design Point Study of a Semi-Closed Recuperated Intercooled Gas Turbine Combined With a Rankine Bottoming Cycle

1996 ◽  
Author(s):  
Todd S. Nemec ◽  
William E. Lear
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Mechanical Design ◽  
Rankine Cycle ◽  
System Size ◽  
Combined Cycle ◽  
Specific Power ◽  
Design Point ◽  
Recirculation Flow ◽  
Design Variables

A design point study of a semi-closed recuperated intercooled gas turbine combined with a closed, unfired, Rankine cycle is presented to demonstrate the overall thermodynamic design and efficiency tradeoffs for this type of cycle. Through its semi-closed design, having control over combustor equivalence ratio and recirculation flow exit pressure, this cycle provides improvements in emissions, specific power (net system power output divided by gas turbine inlet airflow), part power thermal efficiency, and overall system size relative to a combined cycle with an open cycle gas turbine. The relationship of design variables to cycle and component selection is discussed. Interface heat exchanger configuration, along with bottoming cycle choices of regeneration, feedwater heating, and fluid (H2O or DOWTHERM®A) are evaluated to determine their effects on mechanical design and thermal efficiency.

System Study on Partial Gasification Combined Cycle With CO2 Recovery

2008 ◽  
Vol 130 (5) ◽  
Author(s):  
Yujie Xu ◽  
Hongguang Jin ◽  
Rumou Lin ◽  
Wei Han
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Rankine Cycle ◽  
Combined Cycle ◽  
Energy Utilization ◽  
Working Fluid ◽  
The Novel ◽  
Integrated Gasification Combined Cycle ◽  
Partial Gasification ◽  
Co2 Recovery

A partial gasification combined cycle with CO2 recovery is proposed in this paper. Partial gasification adopts cascade conversion of the composition of coal. Active composition of coal is simply gasified, while inactive composition, that is char, is burnt in a boiler. Oxy-fuel combustion of syngas produces only CO2 and H2O, so the CO2 can be separated through cooling the working fluid. This decreases the amount of energy consumption to separate CO2 compared with conventional methods. The novel system integrates the above two key technologies by injecting steam from a steam turbine into the combustion chamber of a gas turbine to combine the Rankine cycle with the Brayton cycle. The thermal efficiency of this system will be higher based on the cascade utilization of energy level. Compared with the conventional integrated gasification combined cycle (IGCC), the compressor of the gas turbine, heat recovery steam generator (HRSG) and gasifier are substituted for a pump, reheater, and partial gasifier, so the system is simplified obviously. Furthermore, the novel system is investigated by means of energy-utilization diagram methodology and provides a simple analysis of their economic and environmental performance. As a result, the thermal efficiency of this system may be expected to be 45%, with CO2 recovery of 41.2%, which is 1.5–3.5% higher than that of an IGCC system. At the same time, the total investment cost of the new system is about 16% lower than that of an IGCC. The comparison between the partial gasification technology and the IGCC technology is based on the two representative cases to identify the specific feature of the proposed system. The promising results obtained here with higher thermal efficiency, lower cost, and less environmental impact provide an attractive option for clean-coal utilization technology.

System Study on Partial Gasification Combined Cycle With CO2 Recovery

2006 ◽  
Author(s):  
Yujie Xu ◽  
Hongguang Jin ◽  
Rumou Lin ◽  
Wei Han
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Rankine Cycle ◽  
Combined Cycle ◽  
Energy Utilization ◽  
Working Fluid ◽  
The Novel ◽  
Attractive Option ◽  
Partial Gasification ◽  
Co2 Recovery

A partial gasification combined cycle with CO2 recovery is proposed in this paper. Partial gasification adopts cascade conversion of the composition of coal. Active composition of coal is simply gasified, while inactive composition, that is char, is burnt in a boiler. Oxy-fuel combustion of syngas produces only CO2 and H2O, so the CO2 can be separated through cooling the working fluid. This decreases the amount of energy consumed to separate CO2 compared with conventional methods. The novel system integrates the above two key technologies, by injecting steam from a steam turbine into the combustion chamber of a gas turbine, to combine the Rankine cycle with the Brayton cycle. The thermal efficiency of this system will be higher based on the cascade utilization of energy level. Compared to the conventional IGCC, the compressor of the gas turbine, HRSG and gasifier are substituted for a pump, reheater and partial gasifier, so the system is simplified obviously. Furthermore, the novel system is investigated by means of EUD (Energy-Utilization Diagram) methodology and provides a simple analysis of their economic and environmental performance. As a result, the thermal efficiency of this system may be expected to be 46%, with recovery of 50% of CO2, which is 3–5% higher than that of an IGCC system. At the same time, the total investment cost of the new system is about 21.5% lower than that of an IGCC. The promising results obtained here with higher thermal efficiency, lower cost and less environmental impact provide an attractive option for clean coal utilization technology.

Electrical Power Generation: Fossil Fuels

2017 ◽  
Author(s):  
Peter Rez
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Power Plants ◽  
Fossil Fuels ◽  
Turbine Blades ◽  
Electrical Power ◽  
Rankine Cycle ◽  
Combined Cycle ◽  
Brayton Cycle ◽  
Steam Temperature

Nearly all electrical power is generated by rotating a coil in a magnetic field. In most cases, the coil is turned by a steam turbine operating according to the Rankine cycle. Water is boiled and heated to make high-pressure steam, which drives the turbine. The thermal efficiency is about 30–35%, and is limited by the highest steam temperature tolerated by the turbine blades. Alternatively, a gas turbine operating according to the Brayton cycle can be used. Much higher turbine inlet temperatures are possible, and the thermal efficiency is higher, typically 40%. Combined cycle generation, in which the hot exhaust from a gas turbine drives a Rankine cycle, can achieve thermal efficiencies of almost 60%. Substitution of coal-fired by combined cycle natural gas power plants can result in significant reductions in CO2 emissions.

Evaluation of the Effect of Firing Temperature, Cycle, Engine Configuration, Components, and Bottoming Cycle on the Overall Thermal Efficiency of an Indirectly Coal-Fired Gas Turbine Based Power Plant

2006 ◽  
Author(s):  
Richard P. Johnston
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Power Plants ◽  
Rankine Cycle ◽  
Combined Cycle ◽  
Working Fluid ◽  
Turbine Engine ◽  
Combined Cycle Plant ◽  
Plant Power

Potential LHV performance of an indirect coal-fired gas turbine-based combined cycle plant is explored and compared to the typical LHV 35–38 % thermal efficiencies achievable with current coal-fired Rankine Cycle power plants. Plant performance with a baseline synchronous speed, single spool 25:1 pressure ratio gas turbine with a Rankine bottoming cycle was developed. A coal-fired High Temperature Advanced Furnace (HITAF) supplying 2000° F. (1093° C.) hot pressurized air for the gas turbine was modeled for the heat source. The HITAF concept along with coal gas for supplemental heating, are two important parts of the clean coal technology program for power plants. [1,2] From this baseline power plant arrangement, different gas turbine engine configurations with two pressure ratios are evaluated. These variations include a dual spool concentric shaft gas turbine, dual spool non-concentric shaft arrangement, intercooler, liquid metal loop re-heater, free power turbine (FPT) and post HITAF duct burner (DB). A dual pressure Heat Recovery Steam Generator (HRSG) with varying steam pressures to fit conditions is used for each engine. A novel steam generating method employing flash tank technology is applied when a water-cooled intercooler is incorporated. A halogenated hydrocarbon working fluid is also evaluated for lower temperature sub-bottoming Rankine cycle equipment. Current technology industrial gas turbine component performance levels are applied to these various engines to produce a range of LHV gross gas turbine thermal efficiency estimates. These estimates range from the lower thirties to over forty percent. Overall LHV combined cycle plant gross thermal efficiencies range from nearly forty to over fifty percent. All arrangements studied would produce significant improvements in thermal efficiency compared to current coal-fired Rankine cycle power plants. Regenerative inter-cooling, free power turbines, and dual-spool non-concentric shaft gas turbine arrangements coupled with post-HITAF duct burners produced the highest gas turbine engine and plant efficiency results. These advanced engine configurations should also produce operational benefits such as easier starting and much improved part power efficiency over the baseline engine arrangement. An inter-turbine liquid metal re-heat loop reduced engine thermal efficiency but did increase plant power output and efficiency for the example studied. Use of halogenated hydrocarbons as a working fluid would add to plant power output, but at the cost of significant additional plant equipment.

scholarly journals Thermodynamic analysis of high temperature nuclear reactor coupled with advanced gas turbine combined cycle

2019 ◽  
Vol 23 (Suppl. 4) ◽  
pp. 1187-1197 ◽  
Author(s):  
Marek Jaszczur ◽  
Michal Dudek ◽  
Zygmunt Kolenda
Keyword(s):  
High Temperature ◽  
Power Plant ◽  
Gas Turbine ◽  
Thermodynamic Analysis ◽  
Thermal Efficiency ◽  
Nuclear Power ◽  
Coal Gasification ◽  
Nuclear Reactor ◽  
Combined Cycle ◽  
Oil Processing

One of the most advanced and most effective technology for electricity generation nowadays based on a gas turbine combined cycle. This technology uses natural gas, synthesis gas from the coal gasification or crude oil processing products as the energy carriers but at the same time, gas turbine combined cycle emits SO2, NOx, and CO2 to the environment. In this paper, a thermodynamic analysis of environmentally friendly, high temperature gas nuclear reactor system coupled with gas turbine combined cycle technology has been investigated. The analysed system is one of the most advanced concepts and allows us to produce electricity with the higher thermal efficiency than could be offered by any currently existing nuclear power plant technology. The results show that it is possible to achieve thermal efficiency higher than 50% what is not only more than could be produced by any modern nuclear plant but it is also more than could be offered by traditional (coal or lignite) power plant.

Redesigning a commercial combined cycle in an undergraduate thermodynamics course: Connecting theory to practical cycle design

2020 ◽  
pp. 030641902090464
Author(s):  
Tohru Suwa ◽  
Tetuko Kurniawan
Keyword(s):  
High Pressure ◽  
High Temperatures ◽  
Undergraduate Students ◽  
Thermal Efficiency ◽  
Mechanical Engineering ◽  
Rankine Cycle ◽  
Combined Cycle ◽  
Thermal Cycles ◽  
Electric Company ◽  
Engineering Personnel

Due to various reasons, the concepts of thermodynamics are not easy to grasp for undergraduate students. One of the major reasons is that the students are mostly unfamiliar with the thermodynamics devices discussed in the courses. Offering courses with experiments is an effective approach to solve this issue. However, it is not practical or possible for universities to own devices that operate at high temperatures and with high pressure fluids. With the cooperation of a nearby electric company, undergraduate students of a thermodynamics course from the Department of Mechanical Engineering measured thermal performances of a commercial combined cycle and its sub-systems at the President University. After learning about the theory of thermal cycles, the students analyzed the thermal performances of actual thermodynamics cycles. Subsequently, they analyzed the thermal efficiency improvements when reheating or regeneration is applied to the simple Rankine cycle in the combined cycle. At the end of the course, the students gave presentations before the electric company’s management and engineering personnel, akin to professional engineers. This course is structured to familiarize undergraduate students with thermodynamics cycles and devices.

scholarly journals A Useful Equation for Gas Turbine Design

2018 ◽  
Vol 140 (03) ◽  
pp. S52-S53
Author(s):  
Lee S. Langston
Keyword(s):  
Heat Transfer ◽  
Heat Conduction ◽  
Gas Turbine ◽  
Rankine Cycle ◽  
Combined Cycle ◽  
Brayton Cycle ◽  
Nonlinear Superposition ◽  
Transient Conditions ◽  
One Dimensional ◽  
Turbine Design

This article presents three different gas turbine phenomena and design cases. The sketch in the article shows a schematic of a combined cycle powerplant consisting of a Brayton cycle (gas turbine) whose exhaust provides energy to a Rankine cycle (steam turbine). Frequently, one can use simple but exact one-dimensional (1D) heat conduction solutions to estimate the heat loss or gain of gas turbine components under transient conditions. These easy-to-use solutions are found in most undergraduate heat transfer texts. The article suggests that those three widely different gas turbine phenomena and design cases all have the simple, nonlinear superposition form.

Impact of Inlet Fogging on the Performance of Steam Injected Cooled Gas Turbine Based Combined Cycle Power Plant

2017 ◽  
Author(s):  
Anoop Kumar Shukla ◽  
Onkar Singh
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Steam Injection ◽  
Combined Cycle ◽  
Specific Power ◽  
Temperature Cycle ◽  
Inlet Temperature ◽  
Combined Cycle Power Plant

Gas/steam combined cycle power plants are extensively used for power generation across the world. Today’s power plant operators are persistently requesting enhancement in performance. As a result, the rigour of thermodynamic design and optimization has grown tremendously. To enhance the gas turbine thermal efficiency and specific power output, the research and development work has centered on improving firing temperature, cycle pressure ratio, adopting improved component design, cooling and combustion technologies, and advanced materials and employing integrated system (e.g. combined cycles, intercooling, recuperation, reheat, chemical recuperation). In this paper a study is conducted for combining three systems namely inlet fogging, steam injection in combustor, and film cooling of gas turbine blade for performance enhancement of gas/steam combined cycle power plant. The evaluation of the integrated effect of inlet fogging, steam injection and film cooling on the gas turbine cycle performance is undertaken here. Study involves thermodynamic modeling of gas/steam combined cycle system based on the first law of thermodynamics. The results obtained based on modeling have been presented and analyzed through graphical depiction of variations in efficiency, specific work output, cycle pressure ratio, inlet air temperature & density variation, turbine inlet temperature, specific fuel consumption etc.

Proposal of Innovative Gas Turbine Combined Cycle Power Generation System

2004 ◽  
Author(s):  
Hideto Moritsuka
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Generation System ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Power Generation System

In order to estimate the possibility to improve thermal efficiency of power generation use gas turbine combined cycle power generation system, benefits of employing the advanced gas turbine technologies proposed here have been made clear based on the recently developed 1500C-class steam cooling gas turbine and 1300C-class reheat cycle gas turbine combined cycle power generation systems. In addition, methane reforming cooling method and NO reducing catalytic reheater are proposed. Based on these findings, the Maximized efficiency Optimized Reheat cycle Innovative Gas Turbine Combined cycle (MORITC) Power Generation System with the most effective combination of advanced technologies and the new devices have been proposed. In case of the proposed reheat cycle gas turbine with pressure ratio being 55, the high pressure turbine inlet temperature being 1700C, the low pressure turbine inlet temperature being 800C, combined with the ultra super critical pressure, double reheat type heat recovery Rankine cycle, the thermal efficiency of combined cycle are expected approximately 66.7% (LHV, generator end).

Advanced Gas Turbine and High Performance Gas-Steam Combined Cycle Plant With Blade Cooling Air Controlling

2006 ◽  
Author(s):  
Tadashi Tsuji
Keyword(s):  
Power Generation ◽  
Heat Exchanger ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Hot Water ◽  
Blade Cooling ◽  
Combined Cycle Plant ◽  
Cooling Air

Air cooling blades are usually applied to gas turbines as a basic specification. This blade cooling air is almost 20% of compressor suction air and it means that a great deal of compression load is not converted effectively to turbine power generation. This paper proposes the CCM (Cascade Cooling Module) system of turbine blade air line and the consequent improvement of power generation, which is achieved by the reduction of cooling air consumption with effective use of recovered heat. With this technology, current gas turbines (TIT: turbine inlet temperature: 1350°C) can be up-rated to have a relative high efficiency increase. The increase ratio has a potential to be equivalent to that of 1500°C Class GT/CC against 1350°C Class. The CCM system is designed to enable the reduction of blade cooling air consumption by the low air temperature of 15°C instead of the usual 200–400°C. It causes the turbine operating air to increase at the constant suction air condition, which results in the enhancement of power and thermal efficiency. The CCM is installed in the cooling air line and is composed of three stage coolers: steam generator/fuel preheater stage, heat exchanger stage for hot water supplying and cooler stage with chilled water. The coolant (chilled water) for downstream cooler is produced by an absorption refrigerator operated by the hot water of the upstream heat exchanger. The proposed CCM system requires the modification of cooling air flow network in the gas turbine but produces the direct effect on performance enhancement. When the CCM system is applied to a 700MW Class CC (Combined Cycle) plant (GT TIT: 135°C Class), it is expected that there will be a 40–80MW increase in power and +2–5% relative increase in thermal efficiency.

Sign in / Sign up

Export Citation Format

Share Document