scholarly journals On the Application of Variable Camber Blading in Axial Flow Fans and Compressors

1996 ◽  
Author(s):  
U. K. Saha ◽  
B. Roy
Keyword(s):  
Performance Studies ◽  
Pressure Ratio ◽  
Pressure Coefficient ◽  
Axial Flow ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
High Pressure Ratio ◽  
Coefficient Distribution ◽  
Wide Range ◽  
Design Power

For land and marine based gas turbine engines, heavy duty industrial axial flow fans and compressors, variable camber tandem blading seems to be an attractive proposition in the pursuit of high pressure ratio machines under design and off-design power settings. In the present investigations, experiments have been carried out in a cascade wind tunnel to explore the variable camber capability of a tandem blade at two extreme camber settings. Aerodynamic performance studies have been made qualitatively on the basis of static pressure coefficient distribution, diffusion factor and mass averaged loss coefficient data. Experimental evidences demonstrate the possible operation of variable camber blading within a wide range of 20° camber variation.

The Effects of Ambient Conditions on Gas Turbine Emissions—Generalized Correction Factors

1978 ◽  
Vol 100 (4) ◽  
pp. 640-646 ◽  
Author(s):  
P. Donovan ◽  
T. Cackette
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Correction Factors ◽  
Oxides Of Nitrogen ◽  
Ambient Conditions ◽  
Nitrogen Emission ◽  
Wide Range

A set of factors which reduces the variability due to ambient conditions of the hydrocarbon, carbon monoxide, and oxides of nitrogen emission indices has been developed. These factors can be used to correct an emission index to reference day ambient conditions. The correction factors, which vary with engine rated pressure ratio for NOx and idle pressure ratio for HC and CO, can be applied to a wide range of current technology gas turbine engines. The factors are a function of only the combustor inlet temperature and ambient humidity.

Design Study of an Advanced Concept Simple Gas Turbine for Possible Use in Low Emission Automobiles

1972 ◽  
Author(s):  
H. C. Eatock ◽  
M. D. Stoten
Keyword(s):  
High Pressure ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Simple Cycle ◽  
Turbine Engines ◽  
Nox Emissions ◽  
Preliminary Design ◽  
Gas Turbine Engines ◽  
High Pressure Ratio

United Aircraft Corporation studied the potential costs of various possible gas turbine engines which might be used to reduce automobile exhaust emissions. As part of that study, United Aircraft of Canada undertook the preliminary design and performance analysis of high-pressure-ratio nonregenerated (simple cycle) gas turbine engines. For the first time, high levels of single-stage component efficiency are available extending from a pressure ratio less than 4 up to 10 or 12 to 1. As a result, the study showed that the simple-cycle engine may provide satisfactory running costs with significantly lower manufacturing costs and NOx emissions than a regenerated engine. In this paper some features of the preliminary design of both single-shaft and a free power turbine version of this engine are examined. The major component technology assumptions, in particular the high pressure ratio centrifugal compressor, employed for performance extrapolation are explained and compared with current technology. The potential low NOx emissions of the simple-cycle gas turbine compared to regenerative or recuperative gas turbines is discussed. Finally, some of the problems which might be encountered in using this totally different power plant for the conventional automobile are identified.

A Mean Line Prediction Method for Axial Flow Turbine Efficiency

1982 ◽  
Vol 104 (1) ◽  
pp. 111-119 ◽  
Author(s):  
S. C. Kacker ◽  
U. Okapuu
Keyword(s):  
Gas Turbine ◽  
Axial Flow ◽  
Prediction Method ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Loss System ◽  
Turbine Efficiency ◽  
Wide Range ◽  
Line Loss ◽  
Axial Turbines

A mean line loss system is described, capable of predicting the design point efficiencies of current axial turbines of gas turbine engines. This loss system is a development of the Ainley/Mathieson technique of 1951. The prediction method is tested against the “Smith’s chart” and against the known efficiencies of 33 turbines of recent design. It is shown to be able to predict the efficiencies of a wide range of axial turbines of conventional stage loadings to within ± 1 1/2 percent.

scholarly journals ВПЛИВ ГУСТОТИ РЕШІТКИ НА АЕРОДИНАМІЧНУ НАВАНТАЖЕНІСТЬ РОБОЧОГО КОЛЕСА ОСЬОВОГО ВЕНТИЛЯТОРА

2020 ◽  
pp. 38-43
Author(s):  
Екатерина Викторовна Дорошенко ◽  
Михаил Владимирович Хижняк ◽  
Юрий Матвеевич Терещенко
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Turbine Engines ◽  
Average Radius ◽  
Gas Turbine Engines ◽  
Axial Fan ◽  
Aerodynamic Loading ◽  
Wide Range ◽  
Axial Fans ◽  
Bypass Ratio

The main requirements that apply to axial fans and axial compressors of aircraft gas turbine engines include minimum dimensions and weight; high aerodynamic load; high coefficient of performance; wide range of steady work; high reliability. For gas turbine engines, the requirements of minimum weight and dimensions are especially important, since the engines must provide flights at high velocities and altitudes. This study aims to assess the effect of the solidity of the impeller fan on the average radius on the aerodynamic loading of the impeller of an axial fan for an engine with a high bypass ratio. The object of the study is the impeller of the fan. The solidity of the impeller fan on the average radius varied in the range from 1.8 to 0.82, the number of blades of the impeller fan varied from 33 to 15, respectively. The studies in this work were carried out by the method of numerical experiment. The flow in the axial fans was simulated by solving the system of Navier-Stokes equations, which were closed by the SST turbulent viscosity model. Based on the analysis of the results of the study, an assessment is made of the influence of the solidity of the impeller fan at an average radius on the aerodynamic loading of the impeller of an axial fan for an engine with a high bypass ratio. The research results showed that with a decrease in the solidity of the impeller fan at an average radius of 1.8 to 0.82 in operating modes with an axial inlet velocity of 80 to 120 m / s, the impeller fan pressure ratio decreases by 0.11 ... 3.2 %. The maximum decrease in the fan pressure ratio increase for the fan impeller with the parameters studied is 3.2 %, with a decrease in the number of fan blades from 33 to 15, while the total weight of the blades decreases by 54.55 %. The decrease in the solidity on the average radius of the impeller of the studied fan leads to a decrease in the relative sizes of the low-velocity zones at the sleeve and on the periphery and to a decrease in the level of flow unevenness. A further reduction in the level of flow non-uniformity behind the fan is possible when using the boundary layer control in the fan - this is the task of subsequent studies.

scholarly journals МЕТОД РАСЧЕТА ТЕРМОГАЗОДИНАМИЧЕСКИХ ПАРАМЕТРОВ ТУРБОВАЛЬНОГО ГТД НА ОСНОВЕ ПОВЕНЦОВОГО ОПИСАНИЯ ЛОПАТОЧНЫХ МАШИН. ЧАСТЬ 1. ОСНОВНЫЕ УРАВНЕНИЯ

2018 ◽  
pp. 48-58
Author(s):  
Людмила Георгиевна Бойко ◽  
Олег Владимирович Кислов ◽  
Наталия Владимировна Пижанкова
Keyword(s):  
Gas Turbine ◽  
Flow Rate ◽  
Pressure Ratio ◽  
Turbine Engines ◽  
Geometrical Parameters ◽  
Gas Turbine Engines ◽  
Balance Equations ◽  
Wide Range ◽  
In Series ◽  
Multistage Compressor

Gas turbine engines processes mathematic simulations are widely used in different steps of its living cycle. All engine simulations may be divided into different difficulty levels: higher simulation level allows doing a more pre­cise description of physical processes in main units of gas turbine engines and their elements. It gives the oppor­tunity for getting better arrangement of calculation results and experimental data, reduce the quality of factors, which are traditionally used in determine engine operational characteristics with 1-level models.The purpose of the article is to describe the thermogasdynamic parameters and maintenance perfomances cal­culation method, which based on second level mathematic simulation. Its main feature is blade-to-blade turbomachines description (multistage compressor and multistage cooling gas turbine), which allows to take into account blade and flow path geometrical parameters. Their changing during the gas turbine engine design and de­velopment processes influence its performances: thrust, fuel consumption, efficiency as functions of values of flow rate, rotational speed, engine entrance conditions and so on. All these dependences could be defined by using proposed calculation method.In distinction from methods which are noted, this method allows to concede compressor or turbine incidence angles, drag values, pressure ratio, surge margin in design and off-design  engine regimes. The opportunity to take into account by-passing and air bleeding from compressor blade channels and their engine parameters influence is very important also.The article includes calculation method main points, block-scheme, equations system, which gives the opportunity of alignment the engine units and their elements in wide range of state working regimes. Set of equations consists of flow rate balance equations through the stages of multistage compressor and turbine, combustion chamber and connected channels. Also system includes power balance equations, by-passing, air bleeding from compressor stages channels, its admission into the cooling turbine stages and ac­counts their thermodynamic parameters. Compressors and turbines maps parameters are calculated with main turbomachinery theory lows and semi-empirical dependences.This article is the first in series of articles, which considers this problem

scholarly journals Design Methodology for Splittered Axial Compressor Rotors

1990 ◽  
Author(s):  
K.-L. Tzuoo ◽  
S. S. Hingorani ◽  
A. K. Sehra
Keyword(s):  
High Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Meridional Flow ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Viscous Effects ◽  
High Pressure Ratio ◽  
Rotor Design ◽  
Work Distribution

Recent trend toward lightweight, compact compression systems for advanced aircraft gas turbine engines has created a need for very high pressure ratio fan and compressor stages. One way of achieving pressure ratio in excess of 3:1 in an axial blade row is to introduce splitters (partial vanes) between the principal blades, a concept pioneered by Wennerstrom during early 70s for application in a 3:1 pressure ratio single axial stage. This paper presents an advanced methodology for high pressure ratio splittered rotor design. The methodology centers around combining a meridional flow calculation, an arbitrary meanline blade generation procedure, and 3-D inviscid and viscous analyses. Methods for specifying work distribution, solidity, loss, and deviation distributions, as well as the airfoil generation and splitter vane placement are discussed in detail. Importance of 3-D viscous effects along with results from a 3-D viscous calculation for Wennerstrom’s splittered rotor are also presented.

Exergetic Analysis of a Cross-Flow Microchannel Heat Exchanger for Bleed Air Cooling in Aircraft Gas Turbine Engines

2014 ◽  
Author(s):  
Matthew B. Rivera ◽  
Randall D. Manteufel
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Heat Exchanger ◽  
Pressure Ratio ◽  
Cross Flow ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Exergy Destruction ◽  
High Pressure Ratio ◽  
Exergetic Analysis

A current issue with high-pressure-ratio compressors found in aircraft engines is the temperature of the air exiting the compressor. The exiting air is used as coolant for engine components found in later stages of the engine such as first-stage turbine blades, and afterburner walls. A viable option for reducing outlet temperature of high-pressure-ratio compressors is to “bleed-off” a fraction of the air which is cooled in a heat exchanger by rejecting heat into the liquid fuel stream and then use the air for cooling critical components downstream. Bleeding off air from the outlet of the compressor has two benefits: (1) air temperature is reduced, and (2) fuel temperature is elevated. Along with reduced air temperatures, the fuel will ultimately receive the heat lost from the air, making the fuel more ideal for combustion purposes. The higher temperature the fuel is received in the combustion process, the greater the work output will be according to the basics of thermodynamic combustion. The objective of this case study is to optimize the efficiency of the cross-flow micro channel heat exchanger, with respect to (1) volume (1.75–2.75 mm3) and heat transfer, and (2) weight (0.15–.25 N) and heat transfer. The optimization of the heat exchanger will be evaluated within the bounds of the 2nd law of thermodynamics (exergy). The only effective way to measure the 2nd law of thermodynamics is through exergy destruction or its equivalent form: entropy generation as a factor of dead state temperature. With relations and equations obtained to design an optimal heat exchanger, applications to high performance aircraft gas turbine engines is considered through exergy. The importance of developing an exergetic analysis for a thermal system is highly effective for identifying area’s within the system that have the path of highest resistance to work potential through various modes of heat transfer and pressure loss. Thus, optimization to reduce exergy destruction is sought after through this design method alongside verifying other heat exchanger methods through effectiveness.

Optimisation Method for Multistage Compressors

2021 ◽  
pp. 38-59
Author(s):  
E.S. Goryachkin ◽  
V.N. Matveev ◽  
G.M. Popov ◽  
O.V. Baturin ◽  
Yu.D. Novikova
Keyword(s):  
Gas Turbine ◽  
Cfd Simulation ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Stability Margin ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Data Vector ◽  
Minimum Number ◽  
Multistage Compressors

The paper presents an algorithm for seeking an optimal blade configuration for multistage axial-flow compressors. The primary tool behind the algorithm is 3D CFD simulation, augmented by commercial optimisation software. The core of the algorithm involves feeding an initial data vector to the parametric simulation module so as to form a "new" blade geometry, which is then transferred to 3D computational software. The results obtained are further processed in a program that implements the algorithm for seeking the optimum and forms a new input data vector to achieve the set goal. We present a method of parametrically simulation the blade shape, implemented in a software package, making it possible to describe the shape of the compressor blade profiles using a minimum number of variables and to automatically change the shape in the optimisation cycle. The algorithm developed allows the main parameters of compressor operation (efficiency, pressure ratio, air flow rate, etc.) to be improved by correcting the profile shape and relative position of the blades. The algorithm takes into account various possible constraints. We used the method developed to solve practical problems of optimising multistage axial compressors of gas turbine engines for various purposes, with the number of compressor stages ranging from 3 to 15. As a result, the efficiency, pressure ratio and stability margin of gas turbine engines were increased

scholarly journals Effect of Outer Casing Treatment and Tip Clearance on Stall Margin of a Supersonic Rotating Cascade

1975 ◽  
Author(s):  
Jean Fabri ◽  
Jean Reboux
Keyword(s):  
Aspect Ratio ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Tip Clearance ◽  
Stall Margin ◽  
Casing Treatment ◽  
High Pressure Ratio ◽  
Wide Range ◽  
Supersonic Regime ◽  
The One

Use of grooved outer casing to improve stall margin of high aspect ratio, high pressure ratio axial flow compressors has already been reported in the literature. Tests were made on a low aspect ratio supersonic compressor simulating a rotor of one of the last stages of an advanced multistage compressor to show the gain in performance due to deep grooves in the outer casing. The gain in stall margin is similar to the one that can be obtained by reducing the tip clearance of the rotor; however, with grooves there is a gain in pressure ratio whereas a decrease in pressure ratio was detected when testing the smaller tip clearance. The gain in performance due to outer casing grooves was observed for a wide range of tip Mach numbers, even in the high supersonic regime.

Design, Development and Application of Vehicle Gas Turbine Engines

1966 ◽  
Vol 181 (1) ◽  
pp. 149-172
Author(s):  
P. A. Phillips ◽  
Peter Spear
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Low Cost ◽  
Engine Performance ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Design Development ◽  
Turbine Engine ◽  
Wide Range ◽  
Cycle Temperature

After briefly summarizing worldwide automotive gas turbine activity, the paper analyses the power plant requirements of a wide range of vehicle applications in order to formulate the design criteria for acceptable vehicle gas turbines. Ample data are available on the thermodynamic merits of various gas turbine cycles; however, the low cost of its piston engine competitor tends to eliminate all but the simplest cycles from vehicle gas turbine considerations. In order to improve the part load fuel economy, some complexity is inevitable, but this is limited to the addition of a glass ceramic regenerator in the 150 b.h.p. engine which is described in some detail. The alternative further complications necessary to achieve satisfactory vehicle response at various power/weight ratios are examined. Further improvement in engine performance will come by increasing the maximum cycle temperature. This can be achieved at lower cost by the extension of the use of ceramics. The paper is intended to stimulate the design application of the gas turbine engine.

Sign in / Sign up

Export Citation Format

Share Document