scholarly journals Update on Westinghouse’s Advanced Turbine Systems Program

1997 ◽  
Author(s):  
David J. Amos ◽  
Ihor S. Diakunchak ◽  
Gerard McQuiggan ◽  
Leslie R. Southall ◽  
Gregg P. Wagner
Keyword(s):  
Gas Turbines ◽  
Combined Cycle ◽  
Advanced Materials ◽  
Nox Emissions ◽  
Design Concepts ◽  
Engine Design ◽  
Program Objective ◽  
Low Nox Combustion ◽  
Steam Cooling ◽  
Power Generation Systems

This paper describes progress on Westinghouse’s Advanced Turbine Systems (ATS) Program. The ATS Program objective is to develop new utility gas turbines with greater than 60% net plant thermal efficiency, NOx emissions limited to less than 10 parts per million, reduced cost of electricity generation by 10% over current systems, and reliability-availability-maintainability equivalent to modern power generation systems. The Westinghouse ATS plant is a highly efficient combined cycle, based on an advanced gas turbine incorporating novel design concepts and enhancements of existing technologies. The 501 ATS engine is a fuel-flexible design operating on natural gas with provisions for future conversion to coal or biomass fuels. It is based on proven concepts employed in Westinghouse 501F and 501G engines. To achieve the required performance and reliability, the engine utilizes closed-loop steam cooling, advanced materials and coatings, and enhanced component performance. To minimize NOx emissions, an ultra-low NOx combustion system was incorporated. To ensure success, the necessary technologies were developed and integrated into the ATS engine design.

Technology Development Programs for the Advanced Turbine Systems Engine

1996 ◽  
Author(s):  
Ihor S. Diakunchak ◽  
Ronald L. Bannister ◽  
David J. Huber ◽  
D. Frank Roan
Keyword(s):  
Closed Loop ◽  
Technology Development ◽  
Combined Cycle ◽  
Advanced Materials ◽  
Development Programs ◽  
Turbine Engine ◽  
Design Concepts ◽  
Current State ◽  
Low Nox Combustion ◽  
Steam Cooling

This paper describes the technologies that are being developed or extended beyond the current state-of-the-art to achieve Advanced Turbine Systems (ATS) Program goals. The Westinghouse ATS plant is an advanced closed-loop enoled combined cycle, based on an advanced gas turbine engine incorporating novel design concepts and enhancements of existing technologies. The ATS engine is a fuel-flexible design operating nn natural gas with provisions fnr future conversion to coal or biomass fuels. It is based nn proven concepts employed in 501F and 501G engines. To achieve the required performance and reliability the engine will include closed-loop steam cooling, advanced materials and coatings, and enhanced component performance. To minimize NOx emissions, an ultra-low NOx combustion system will be incorporated. To ensure technical success, development programs are being conducted on the following: closed-loop steam cooling, advanced materials and coatings, component aerodynamic performance, flow visualization, optical diagnostics, combustion generated noise, and catalytic combustion.

Performance of Multiple-Injection Dry Low-NOx Combustor on Hydrogen-Rich Syngas Fuel in an IGCC Pilot Plant

2014 ◽  
Author(s):  
Tomohiro Asai ◽  
Satoschi Dodo ◽  
Mitsuhiro Karishuku ◽  
Nobuo Yagi ◽  
Yasuhiro Akiyama ◽  
...  
Keyword(s):  
Pilot Plant ◽  
Gas Turbines ◽  
Coal Gasification ◽  
Maximum Load ◽  
Combined Cycle ◽  
Nox Emissions ◽  
Multiple Injection ◽  
Test Results ◽  
Low Nox Combustion ◽  
Combustion Of Hydrogen

Successful development of oxygen-blown integrated coal gasification combined cycle (IGCC) technology requires gas turbines capable of achieving dry low-nitrogen oxides (NOx) combustion of hydrogen-rich syngas for low emissions and high plant efficiency. The authors have been developing a “multiple-injection burner” to achieve the dry low-NOx combustion of hydrogen-rich syngas. The purposes of this paper are to present test results of the multi-can combustor equipped with multiple-injection burners in an IGCC pilot plant and to evaluate the combustor performance focusing on effects of flame shapes. The syngas fuel produced in the plant contained approximately 50% carbon monoxide, 20% hydrogen, and 20% nitrogen by volume. In the tests, the combustor that produced slenderer flames achieved lower NOx emissions of 10.9 ppm (at 15% oxygen), reduced combustor liner and burner plate metal temperatures, and lowered the combustion efficiency at the maximum load. The test results showed that the slenderer flames were more effective in reducing NOx emissions and liner and burner metal temperatures. These findings demonstrated that the multiple-injection combustor achieved dry low-NOx combustion of the syngas fuel in the plant.

scholarly journals Development of a Low-NOx LBG Combustor for Coal Gasification Combined Cycle Power Generation Systems

1989 ◽  
Author(s):  
M. Sato ◽  
T. Abe ◽  
T. Ninomiya ◽  
T. Nakata ◽  
T. Yoshine ◽  
...  
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Coal Gasification ◽  
Combined Cycle ◽  
Generation System ◽  
Combustion Technology ◽  
Power Generation System ◽  
Combustion Tests ◽  
Power Generation Systems

From the view point of future coal utilization technology for the thermal power generation systems, the coal gasification combined cycle system has drawn special interest recently. In the coal gasification combined cycle power generation system, it is necessary to develop a high temperature gas turbine combustor using a low-BTU gas (LBG) which has high thermal efficiency and low emissions. In Japan a development program of the coal gasification combined cycle power generation system has started in 1985 by the national government and Japanese electric companies. In this program, 1300°C class gas turbines will be developed. If the fuel gas cleaning system is a hot type, the coal gaseous fuel to be supplied to gas turbines will contain ammonia. Ammonia will be converted to nitric oxides in the combustion process in gas turbines. Therefore, low fuel-NOx combustion technology will be one of the most important research subjects. This paper describes low fuel-NOx combustion technology for 1300°C class gas turbine combustors using coal gaseous low-BTU fuel as well as combustion characteristics and carbon monoxide emission characteristics. Combustion tests were conducted using a full-scale combustor used for the 150 MW gas turbine at the atmospheric pressure. Furthermore, high pressure combustion tests were conducted using a half-scale combustor used for the 1 50 MW gas turbine.

Combined Cycle Plants With Frame 9F Gas Turbines

1991 ◽  
Vol 113 (4) ◽  
pp. 475-481 ◽  
Author(s):  
P. Lugand ◽  
C. Parietti
Keyword(s):  
Power Generation ◽  
Flue Gas ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Catalytic Reduction ◽  
Pressure Level ◽  
Combined Cycle ◽  
Size Factor ◽  
Nox Emissions ◽  
Steam Generators

The new 200 MW class MS 9001F gas turbines allow combined cycle plants to reach even higher output levels and greater efficiency ratings. Size factor and higher firing temperatures, with a three-pressure level steam reheat cycle, offer plant efficiencies in excess of 53 percent. Heat recovery steam generators have been designed to accommodate catalytic reduction elements limiting flue gas NOx emissions to as low as 10 ppm VD (15 percent O2). A range of steam turbine models covers the different possible configurations. Various arrangements based on the 350 or 650 MW power generation modules can be optimally configured to the requirements of each site.

A Dry Low-NOx Gas-Turbine Combustor With Multiple-Injection Burners for Hydrogen-Rich Syngas Fuel: Testing and Evaluation of its Performance in an IGCC Pilot Plant

2013 ◽  
Author(s):  
Tomohiro Asai ◽  
Satoschi Dodo ◽  
Yasuhiro Akiyama ◽  
Akinori Hayashi ◽  
Mitsuhiro Karishuku ◽  
...  
Keyword(s):  
Pilot Plant ◽  
Gas Turbines ◽  
Coal Gasification ◽  
Maximum Load ◽  
Combined Cycle ◽  
Multiple Injection ◽  
Injection Burner ◽  
Partial Load ◽  
Low Nox Combustion ◽  
Surrogate Fuel

Success of oxygen-blown integrated coal gasification combined cycle (IGCC) technology requires gas turbines capable of achieving dry low nitrogen oxides (NOx) combustion of hydrogen-rich syngas for low emissions and high plant efficiency. The authors have been developing a “multiple-injection burner” to achieve dry low-NOx combustion of such hydrogen-rich fuels using surrogate fuel composed of hydrogen, nitrogen, and methane. The purpose of this paper is to report test results of a multi-can combustor equipped with multiple-injection burners for a practical syngas fuel in an IGCC pilot plant and to evaluate its performance. The syngas fuel consisted of hydrogen, nitrogen, and carbon monoxide up to approximately half of its volume. In the test, the combustor achieved stable and reliable operation from ignition through partial load to the maximum load, and achieved NOx emissions of 15.1 ppm (at 15% oxygen) at the maximum load. These findings demonstrated that the combustor achieves dry low-NOx combustion of the syngas fuel in the IGCC pilot plant.

scholarly journals Gas Turbine Topping Stage Based on Energy Exchangers: Process and Performance

1993 ◽  
Author(s):  
Erwin Zauner ◽  
Yau-Pin Chyou ◽  
Frederic Walraven ◽  
Rolf Althaus
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
High Efficiency ◽  
Operating Cost ◽  
Combined Cycle ◽  
Specific Power ◽  
Material Strength ◽  
Nox Emissions ◽  
Gas Temperature ◽  
And Performance

Power generation in gas turbines is facing three main challenges today: • Low pollution prescribed by legal requirements. • High efficiency to obtain low operating cost and low CO2 emissions. • High specific power output to obtain low product and installation cost. Unfortunately, some of these requirements are contradictory: high efficiency and specific power force the development towards higher temperatures and pressures which increase NOx emissions and intensify the cooling and material strength problems. A breakthrough can be achieved by applying an energy exchanger as a topping stage. Inherent advantages are the self-cooled cell-rotor which can be exposed to much higher gas temperature than a steady-flow turbine and a very short residence time at peak temperature which keeps NOx emissions under control. The basic idea has been proposed long time ago. Fundamental research has now led to a new energy exchanger concept. Key issues include symmetric pressure-wave processes, partial suppression of flow separation and fluid mixing, as well as quick afterburning in premixed mode. The concept has been proven in a laboratory-scale engine with very promising results. The application of an energy exchanger as a topping stage onto existing gas turbines would increase the efficiency by 17% (relative) and the power by 25%. Since the temperature level in the turbine remains unchanged, the performance improvement can also be fully utilized in combined cycle applications. This process indicates great potentials for developing advanced gas turbine systems as well as for retrofitting existing ones.

Gas Turbine Systems Designed for Coal Water Slurries

1984 ◽  
Author(s):  
A. J. Giramonti ◽  
F. L. Robson
Keyword(s):  
Power Generation ◽  
Corrosion Resistance ◽  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Ceramic Coatings ◽  
Combined Cycle ◽  
Coal Powder ◽  
Combined Cycle Plant ◽  
Power Generation Systems

Numerous attempts have been made during the past two decades to develop advanced power generation systems which could burn coal or coal-derived fuels both economically and in an environmentally acceptable manner. Although much valuable technology has been derived from these programs, commercially viable power generation alternatives have not yet appeared. One prospective way to expedite the commercialization of advanced coal-fired power systems is to meld the latest gas turbine technology with the emerging technology for producing slurries of water and ultra clean coal. This paper describes a DOE-sponsored program to identify the most attractive gas turbine power system that can operate on slurry fuels. The approach is to use slurries produced from finely ground (<10 microns) coal powder from which most of the ash and sulfur has been removed. The gas turbines will incorporate a rich-burn, quick-quench combustor to minimize conversion of fuel-bound nitrogen to NOx, advanced single crystal alloys with improved hot corrosion resistance and strength, advanced metallic and ceramic coatings with improved erosion and corrosion resistance, and more effective hot section cooling. Two different power plant configurations are covered: a large (nominally 400 MW) combined cycle plant designed for base load applications; and a small (nominally 12 MW) simple-cycle plant designed for peaking, industrial, and cogeneration applications.

Thermodynamic Analysis of Closed Loop Cooled Cycles

1997 ◽  
Author(s):  
Darren T. Watson ◽  
Ian Ritchey
Keyword(s):  
Gas Turbines ◽  
Closed Loop ◽  
Cooling System ◽  
Open Loop ◽  
Combined Cycle ◽  
Relative Advantage ◽  
Specific Power ◽  
Efficiency Gain ◽  
Steam Cooling ◽  
Practical Constraints

Closed loop steam cooling schemes have been proposed by a number of manufacturers for advanced Combined Cycle Gas Turbine (CCGT) power plant (see for example Corman (1996) and Briesch et al. (1994)) asserting that thermal efficiencies in excess of 60% (LHV) are achievable combined with significant improvements of ∼15% in specific power (see Corman (1995)). In understanding the efficiency advantage however, the relative performance of each cooling system (subject to the same practical constraints and technology levels) is a better indicator then the absolute value. Assessment of the performance of such novel schemes generally involves a detailed numerical analysis of an integrated cycle which may often prevent validation of the results or obscure an understanding of the physical basis for the claimed improvements. Here, to overcome this, a group of simplified expressions are defined for the variation of each cycles efficiency due to cooling which show where the differences come from. These expressions are based simply on a calculation of the marginal increase in heat rejected, to the environment from the cycle, due to an increase in the level of cooling. After these relationships are validated using detailed heat balance calculations they are used to compare the main cooling options, namely open loop air, closed loop air and closed loop steam when subject to the same practical constraints and assumptions. Based on these results it is proposed that the relative advantage of closed loop cooling may not be as significant as previously thought. Furthermore, it is shown that the closed loop cooling efficiency gain is heavily dependent on the performance and reliability of substantial Thermal Barrier Coatings (TBCs). Finally, although the majority of recent interest in closed loop cooling schemes has focused upon CCGT plant, there are other systems where the benefits of closed loop steam cooling appear to be greater, in particular cycles involving steam injected gas turbines. Such a cycle is analysed here with a number of advanced cooling options.

Performance of Multiple-Injection Dry Low-NOx Combustors on Hydrogen-Rich Syngas Fuel in an IGCC Pilot Plant

2015 ◽  
Vol 137 (9) ◽  
Author(s):  
Tomohiro Asai ◽  
Satoschi Dodo ◽  
Mitsuhiro Karishuku ◽  
Nobuo Yagi ◽  
Yasuhiro Akiyama ◽  
...  
Keyword(s):  
Power Systems ◽  
Pilot Plant ◽  
Gas Turbines ◽  
Combustion Efficiency ◽  
Combined Cycle ◽  
Nox Emissions ◽  
Multiple Injection ◽  
Test Results ◽  
Integrated Gasification Combined Cycle ◽  
Combustion Of Hydrogen

The successful development of coal-based integrated gasification combined cycle (IGCC) technology requires gas turbines capable of achieving the dry low nitrogen oxides (NOx) combustion of hydrogen-rich syngas fuels for low emissions and high plant efficiency. Mitsubishi Hitachi Power Systems, Ltd. (MHPS) has been developing a “multiple-injection burner” to achieve the dry low-NOx (DLN) combustion of hydrogen-rich syngas fuels. The purposes of this paper are to present the test results of a multican combustor equipped with multiple-injection burners in an IGCC pilot plant, and evaluate combustor performance by focusing on the effects of flame shapes. The syngas fuel produced in the plant contained approximately 50% carbon monoxide, 20% hydrogen, and 20% nitrogen by volume. In the tests, the combustor with slenderer flames achieved lower NOx emissions of 10.9 ppm (at 15% oxygen), reduced combustor liner and burner plate metal temperatures, and lowered combustion efficiency at the maximum gas turbine load. The test results showed that the slenderer flames were more effective in reducing NOx emissions and liner/burner plate metal temperatures. A comparison with the diffusion-flame combustor demonstrated that the multiple-injection combustors achieved the dry low-NOx combustion of the syngas fuel in the plant.

Sign in / Sign up

Export Citation Format

Share Document