Experimental Investigation on Silver-Graphene Hybrid Nanofluid Droplet Evaporation and Wetting Characteristics of its Nanostructured Droplet Residue

2019 ◽  
Author(s):  
Farooq R. Siddiqui ◽  
Edwin C. Y. Tso ◽  
Sau C. Fu ◽  
Christopher Y. H. Chao ◽  
Huihe Qiu
Keyword(s):  
Evaporation Rate ◽  
Volume Fraction ◽  
Spray Cooling ◽  
Droplet Evaporation ◽  
Copper Surface ◽  
Nanoporous Structure ◽  
Hybrid Nanofluid ◽  
Mixing Ratios ◽  
Static Contact ◽  
Wide Range

Abstract Droplet evaporation is a complex phase change process with a wide range of cooling applications, such as spray cooling and dropwise hotspot cooling in microelectronics, to name a few. The hybrid nanofluid droplet evaporation and its residue effects on evaporation of the subsequent hybrid nanofluid droplet is investigated in this research. Silver-graphene (Ag-GNP) hybrid nanofluid exhibiting synergistic thermal properties is investigated and prepared by dispersing silver nanoparticles along with graphene nanoplatelets in water at 0.1% volume fraction and with different mixing ratios, followed by ultrasonication. The evaporation rate and wetting characteristics of a 3 μl volume of Ag-GNP hybrid nanofluid droplet on a copper surface were studied using an optical tensiometer. Once dried, the nanoporous structure of the residue surface was examined using a scanning electron microscope, while the surface roughness was measured using an optical profiler. Experiments were continued to further investigate the evaporation rate and wetting effects of the subsequent Ag-GNP hybrid nanofluid droplet over the residue surface. The results showed improved wetting characteristics, with 88% reduction in initial static contact angle and 163–196% enhancement in evaporation rate of the subsequent Ag-GNP hybrid nanofluid droplets over the residue surfaces as compared to the copper surface.

Evaporation of Silver-Graphene Hybrid Nanofluid Droplet on its Nanostructured Residue and Plain Copper Surfaces at Elevated Temperatures

2020 ◽  
Author(s):  
Farooq Riaz Siddiqui ◽  
Chi Yan Tso ◽  
Sau Chung Fu ◽  
Huihe Qiu ◽  
Christopher Yu Hang Chao
Keyword(s):  
Substrate Temperature ◽  
Evaporation Rate ◽  
Elevated Temperatures ◽  
Droplet Evaporation ◽  
Copper Surface ◽  
Copper Plate ◽  
Hybrid Nanofluid ◽  
Copper Surfaces ◽  
Latent Energy ◽  
Droplet Sizes

Abstract Droplet evaporation is an efficient process as it removes a large amount of heat by using the latent energy, making it suitable for heat transfer applications. In this research, evaporation of the silver-graphene hybrid nanofluid (SGHF) droplet, because of its synergistic thermal conductivity, is investigated for substrate temperature in a range of 25–100 °C. The experiments for droplet evaporation were performed in an environmental facility for two droplet sizes, 3 μL and 30 μL volume, on a copper plate. A 100 W silicone heater mat was used to heat the copper plate from the underside, while two T-type thermocouples were used to monitor its surface temperature. As droplet evaporation ended, a porous residue was formed on the copper surface. Subsequently, a 3 μL volume of the SGHF droplet was dispensed on the porous residue surface. The results showed a tremendous rise in the evaporation rate (up to 160%) for the subsequent SGHF droplet sitting on the porous residue as compared to the non-wetted copper surface. Moreover, the evaporation rate of the SGHF droplet on the copper surface increased up to 56% as compared to the water droplet for a substrate temperature range of 25–100 °C.

Droplet Evaporation of Cu–Al2O3 Hybrid Nanofluid Over Its Residue and Copper Surfaces: Toward Developing a New Analytical Model

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Farooq Riaz Siddiqui ◽  
Chi Yan Tso ◽  
Sau Chung Fu ◽  
Huihe Qiu ◽  
Christopher Y. H. Chao
Keyword(s):  
Analytical Model ◽  
Evaporation Rate ◽  
Heat Dissipation ◽  
High Heat ◽  
Droplet Evaporation ◽  
Copper Surface ◽  
Hybrid Nanofluid ◽  
High Heat Flux ◽  
High Heat Transfer ◽  
Critical Residue

Abstract Droplet evaporation-based cooling techniques, such as the spray cooling, give high heat transfer rates by utilizing latent energy and are usually preferred in thermal applications. However, with the significant rise in heat dissipation levels for high heat flux devices, these devices cannot be thermally managed due to the limited cooling capacity of existing thermal fluids. In this paper, we report the evaporation of the Cu–Al2O3 hybrid nanofluid (HNF) droplet on a copper surface as well as its own residue surface, developed from the evaporation of the first Cu–Al2O3 HNF droplet. As the main novelty, we identify the critical residue size and investigate the residue size effect, above and below the critical residue size, on evaporation rate of the succeeding Cu–Al2O3 HNF droplet resting over a residue surface. We also develop a new analytical model to estimate the Cu–Al2O3 HNF droplet evaporation rate and compare our results with other existing models. The results show that the Cu–Al2O3 HNF droplet gives 17% higher evaporation rate than a water droplet on a copper surface. Also, the evaporation rate of the Cu–Al2O3 HNF droplet on a residue surface sharply increases by 106% with increasing residue size up to the critical residue size. However, further increasing the residue size above its critical value has a negligible effect on the droplet evaporation rate. Moreover, the evaporation rate of the Cu–Al2O3 HNF droplet on its residue surface is enhanced up to 104% when compared to a copper surface.

Modeling of Sessile Droplet Evaporation on Engineered Surfaces

2019 ◽  
Vol 11 (6) ◽  
Author(s):  
Jyoti Prakash ◽  
Basant Singh Sikarwar
Keyword(s):  
Experimental Study ◽  
Relative Humidity ◽  
Evaporation Rate ◽  
Sessile Drop ◽  
Droplet Evaporation ◽  
Contact Angles ◽  
Surface Wettability ◽  
Aluminum Surface ◽  
Complex Nature ◽  
Wide Range

The evaporation of sessile drop has a wide range of application that includes printing, washing, cooling, and coating. Due to the complex nature of drop evaporation process, this phenomenon is reliant on several parameters such as ambiance and physiochemical properties of liquid and surface. In the present study, a mathematical model of water droplet evaporation on an engineered aluminum surface is developed. Experimental study is carried out for the validation of code. The data obtained from the simulation is validated against the data obtained from an experimental study as well as the data available in the literature and good agreement was found among them. Post-validation, the effect of surface wettability and environment conditions on a droplet evaporation rate is estimated. It is inferred from the outcomes that the temperature at the apex of the drop varies linearly with the increasing relative humidity. Droplet volume has a significant impact on the evaporation rate and comparatively higher evaporative flux for a smaller volume of the drop with large contact angles. This unveils the possibility of achieving the required evaporation rate by controlling surface wettability and relative humidity conditions near the drop.

Nanofluid Pendant Droplet Evaporation

2013 ◽  
Author(s):  
William J. Gerken ◽  
Matthew A. Oehlschlaeger
Keyword(s):  
Evaporation Rate ◽  
Volume Fraction ◽  
Colloidal Suspensions ◽  
Droplet Evaporation ◽  
Droplet Surface ◽  
Liquid Volume ◽  
Liquid Volume Fraction ◽  
Pure Ethanol ◽  
Potential Applications

Nanofluids, stable colloidal suspensions of nanoparticles in a base fluid, have potential applications in the heat transfer, combustion and propulsion, manufacturing, and medical fields. Experiments were conducted to determine the evaporation rate of room temperature, millimeter-sized pendant droplets of ethanol laden with varying (0–3%) weight percentages of 40–60 nm aluminum nanoparticles (nAl). High-resolution droplet images were collected as a function of time for the determination of D-square law evaporation rates. Results show an asymptotic decrease in droplet evaporation rate with increasing nAl loading. The evaporation rate decreases by approximately 15% at around 1% to 3% nAl loading relative to the evaporation rate of pure ethanol, a reduction greater than can be explained by reduction in the vapor pressure of an ideal nanofluid mixture by Raoult’s law. It is hypothesized that the reduction in evaporation rate could be due to two phenomena: 1) the reduction in the ethanol volume fraction available for evaporation due to an interfacial layer on the immersed nanoparticle surface and 2) the aggregation of nanoparticles within the droplet and at the droplet surface, reducing the liquid diffusion rate to the surface and the liquid volume fraction at the surface available for evaporation.

Leidenfrost Evaporation of Liquid Nitrogen Droplets

1994 ◽  
Vol 116 (4) ◽  
pp. 999-1006 ◽  
Author(s):  
S. Chandra ◽  
S. D. Aziz
Keyword(s):  
Surface Temperature ◽  
Liquid Nitrogen ◽  
Glass Surface ◽  
Evaporation Rate ◽  
Ambient Pressure ◽  
Droplet Diameter ◽  
Droplet Evaporation ◽  
Copper Surface ◽  
Droplet Impact ◽  
Bubble Nucleation

The evaporation of a single droplet of liquid nitrogen, levitated during film boiling above a solid, impervious surface, was studied experimentally. The droplet initial diameter (1.9 mm), surface temperature (~20°C), ambient temperature (~20°C), and ambient pressure (~0.1 MPa) were held constant. The principal parameters varied were the surface material (copper or glass), and roughness (0.35 to 50 μm). Measurements were made of the droplet diameter evolution and the surface temperature variation during droplet impact. Predictions from existing models of droplets in Leidenfrost evaporation agree well with measurements of the droplet evaporation rate. The droplet lifetime was found to be slightly longer on the glass surface than it was on the copper surface, corresponding to the greater cooling of the glass surface during droplet impact. The droplet evaporation rate was unchanged by small increases in surface roughness. However, ridges on the surface with a height of the same magnitude as the thickness of the vapor film under the drop caused vapor bubble nucleation in the droplet, and significantly reduced the droplet evaporation time.

WATER DROPLET EVAPORATION IN A CHAMBER ISOLATED FROM THE EXTERNAL ENVIRONMENT

2020 ◽  
Vol 6 (3) ◽  
pp. 8-22
Author(s):  
KSENIA A. Batishcheva ◽  
ATLANT E. Nurpeiis
Keyword(s):  
Water Vapor ◽  
Evaporation Rate ◽  
External Environment ◽  
Heat Removal ◽  
Droplet Evaporation ◽  
Droplet Volume ◽  
Evaporation Time ◽  
Aluminum Alloy Amg6 ◽  
Evaporation Of Droplets ◽  
Contact Diameter

With an increase in the productivity of power equipment and the miniaturization of its components, the use of traditional thermal management systems becomes insufficient. There is a need to develop drip heat removal systems, based on phase transition effects. Cooling with small volumes of liquids is a promising technology for microfluidic devices or evaporation chambers, which are self-regulating systems isolated from the external environment. However, the heat removal during evaporation of droplets into a limited volume is a difficult task due to the temperature difference in the cooling device and the concentration of water vapor that is unsteady in time depending on the mass of the evaporated liquid. This paper presents the results of an experimental study of the distilled water microdrops’ (5-25 μl) evaporation on an aluminum alloy AMg6 with the temperatures of 298-353 K in an isolated chamber (70 × 70 × 30 mm3) in the presence of heat supply to its lower part. Based on the analysis of shadow images, the changes in the geometric dimensions of evaporating drops were established. They included the increase in the contact diameter, engagement of the contact line due to nano roughening and chemical composition inhomogeneous on the surface (90-95% of the total evaporation time) of the alloy and a decrease in the contact diameter. The surface temperature and droplet volume did not affect the sequence of changes in the geometric dimensions of the droplets. It was found that the droplet volume has a significant effect on the evaporation time at relatively low substrate temperatures. The results of the analysis of droplet evaporation rates and hygrometer readings have shown that reservoirs with salt solutions can be used in isolated chambers to control the concentration of water vapor. The water droplets evaporation time was determined. The analysis of the time dependences of the evaporation rate has revealed that upon the evaporation of droplets in an isolated chamber under the conditions of the present experiment, the air was not saturated with water vapor. The latter did not affect the evaporation rate.

scholarly journals Factors Affecting Acoustic Properties of Natural-Fiber-Based Materials and Composites: A Review

Textiles ◽  
2021 ◽  
Vol 1 (1) ◽  
pp. 55-85
Author(s):  
Tufail Hassan ◽  
Hafsa Jamshaid ◽  
Rajesh Mishra ◽  
Muhammad Qamar Khan ◽  
Michal Petru ◽  
...  
Keyword(s):  
Sound Absorption ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Fiber Type ◽  
Alkali Treatment ◽  
Acoustic Properties ◽  
Synthetic Fiber ◽  
Sound Insulation ◽  
Factors Affecting ◽  
Wide Range

Recently, very rapid growth has been observed in the innovations and use of natural-fiber-based materials and composites for acoustic applications due to their environmentally friendly nature, low cost, and good acoustic absorption capability. However, there are still challenges for researchers to improve the mechanical and acoustic properties of natural fiber composites. In contrast, synthetic fiber-based composites have good mechanical properties and can be used in a wide range of structural and automotive applications. This review aims to provide a short overview of the different factors that affect the acoustic properties of natural-fiber-based materials and composites. The various factors that influence acoustic performance are fiber type, fineness, length, orientation, density, volume fraction in the composite, thickness, level of compression, and design. The details of various factors affecting the acoustic behavior of the fiber-based composites are described. Natural-fiber-based composites exhibit relatively good sound absorption capability due to their porous structure. Surface modification by alkali treatment can enhance the sound absorption performance. These materials can be used in buildings and interiors for efficient sound insulation.

scholarly journals Conduction and convection heat transfer characteristics of water-based au nanofluids in a square cavity with differentially heated side walls subjected to constant temperatures

2014 ◽  
Vol 18 (suppl.1) ◽  
pp. 189-200 ◽  
Author(s):  
Primoz Ternik ◽  
Rebeka Rudolf
Keyword(s):  
Heat Transfer ◽  
Rayleigh Number ◽  
Base Fluid ◽  
Volume Fraction ◽  
Heat Transfer Characteristics ◽  
Square Cavity ◽  
Onset Of Convection ◽  
Transfer Characteristics ◽  
Wide Range ◽  
Water Based

The present work deals with the natural convection in a square cavity filled with the water-based Au nanofluid. The cavity is heated on the vertical and cooled from the adjacent wall, while the other two horizontal walls are adiabatic. The governing differential equations have been solved by the standard finite volume method and the hydrodynamic and thermal fields were coupled together using the Boussinesq approximation. The main objective of this study is to investigate the influence of the nanoparticles? volume fraction on the heat transfer characteristics of Au nanofluids at the given base fluid?s (i.e. water) Rayleigh number. Accurate results are presented over a wide range of the base fluid Rayleigh number and the volume fraction of Au nanoparticles. It is shown that adding nanoparticles in a base fluid delays the onset of convection. Contrary to what is argued by many authors, we show by numerical simulations that the use of nanofluids can reduce the heat transfer rate instead of increasing it.

scholarly journals Microstructure and magnetic properties of Nd-Fe-B-(Re, Ti) alloys

Nukleonika ◽  
2015 ◽  
Vol 60 (1) ◽  
pp. 29-33
Author(s):  
Mariusz Hasiak
Keyword(s):  
Magnetic Properties ◽  
Phase Composition ◽  
Volume Fraction ◽  
Magnetic Characteristics ◽  
Ti Alloys ◽  
Wide Range ◽  
Magnetically Hard ◽  
Ti Addition ◽  
Microstructure And Magnetic Properties

Abstract The microstructure and magnetic properties of nanocomposite hard magnetic Nd-Fe-B-(Re, Ti) materials with different Nd and Fe contents are studied. The role of Re and Ti addition in phase composition and volume fraction of the Nd-Fe-B phase is determined. All samples are annealed at the same temperature of 993 K for 10 min. Mössbauer spectroscopy shows that the addition of 4 at.% of Re to the Nd8Fe78B14 alloy leads to creation of an ineligible amount of the magnetically hard Nd2Fe14B phase. Moreover, the microstructure and magnetic characteristics recorded in a wide range of temperatures for the Nd8Fe79−xB13Mx (x = 4; M = Re or Ti) alloys are also analyzed.

Sign in / Sign up

Export Citation Format

Share Document