Modeling and Experimental Validation of a Reed Check Valve for Hydraulic Applications

2016 ◽  
Author(s):  
Anthony L. Knutson ◽  
James D. Van de Ven
Keyword(s):  
Internal Combustion Engines ◽  
Check Valve ◽  
Maximum Error ◽  
Fast Response ◽  
Single Element ◽  
Hydraulic Systems ◽  
Test Bed ◽  
Experimental Conditions ◽  
Wide Range ◽  
Reed Valve

Reed valves are a type of check valve commonly found in a wide range of applications including air compressors, internal combustion engines, and even the human heart. While reed valves have been studied extensively in these applications, published research on the modeling and application of reed valves in hydraulic systems is severely lacking. Because the spring and mass components of a reed valve are contained in a single element, it is light and compact compared to traditional disc, poppet, or ball style check valves. These advantages make reed valves promising for use in high frequency applications such as piston pumps, switch-mode hydraulics, and digital hydraulics. Furthermore, the small size and fast response of reed valves provide an opportunity to design pumps capable of operating at higher speeds and with lower dead volumes, thus increasing efficiency and power density. In this paper, a modeling technique for reed valves is presented and validated in a hydraulic piston pump test bed. Excellent agreement between modeled and experimentally measured reed valve opening is demonstrated. Across the range of experimental conditions, the model predicts the pump delivery with an error typically less than 1% with a maximum error of 2.2%.

Modeling and Experimental Validation of a Reed Check Valve for Hydraulic Applications

2020 ◽  
Vol 142 (11) ◽  
Author(s):  
Anthony L. Knutson ◽  
James D. Van de Ven
Keyword(s):  
Internal Combustion Engines ◽  
Check Valve ◽  
Maximum Error ◽  
Fast Response ◽  
Single Element ◽  
Hydraulic Systems ◽  
Test Bed ◽  
Experimental Conditions ◽  
Wide Range ◽  
Reed Valve

Abstract Reed valves are a type of check valve commonly found in a wide range of applications including air compressors, internal combustion engines, musical instruments, and even the human heart. While reed valves have been studied extensively in these applications, published research on the modeling and application of reed valves in hydraulic systems is sparse. Because the spring and mass components of a reed valve are contained in a single element, it is light and compact compared to traditional disk, poppet, or ball style check valves. These advantages make reed valves promising for use in high-frequency applications such as piston pumps, switch-mode hydraulics, and digital hydraulics. Furthermore, the small size and fast response of reed valves provide an opportunity to design pumps capable of operating at higher speeds and with lower dead volumes, thus increasing efficiency and power density. In this paper, a modeling technique for reed valves is presented and validated in a hydraulic piston pump test bed. Excellent agreement between modeled and experimentally measured reed valve opening is demonstrated. Across the range of experimental conditions, the model predicts the pump delivery with an error typically less than 1% with a maximum error of 2.2%.

Dynamic Model of a Novel Alternating Flow (AF) Hydraulic Pump

2017 ◽  
Author(s):  
Mengtang M. Li ◽  
Ryan Foss ◽  
Kim A. Stelson ◽  
James D. Van de Ven ◽  
Eric J. Barth
Keyword(s):  
Dynamic Model ◽  
High Efficiency ◽  
Check Valve ◽  
Viscous Friction ◽  
Operating Conditions ◽  
Hydraulic Systems ◽  
Displacement Control ◽  
Hydraulic Pump ◽  
Wide Range ◽  
Variable Displacement

High power density and good controllability are the most appealing characteristics that make hydraulic systems the best choice for many applications. Current state of the art hydraulic variable displacement pumps show high efficiency at high displacement while they have poor efficiencies at low displacement. This paper proposes a novel alternating flow (AF) variable displacement hydraulic pump to 1) eliminate metering losses by acting as a high-bandwidth pump for displacement control, 2) achieve high efficiency across a wide range of operating conditions and displacements, and 3) allow multiple units to be easily common-shaft mounted for a compact multi-actuator displacement control system from a single prime-mover. A dynamic model using first principles describes the cylinder pressure, flows between pairs of cylinders, and net inlet and outlet flows as a function of the pump’s phase shift angle. The model captures hydraulic check valve dynamics, the effective bulk modulus, leakage flows, and viscous friction. Piston kinematics and dynamics are discussed and energy loss models are presented and used to guide the design for a first prototype of the AF hydraulic pump. The paper presents simulation results from the model that offer an initial evaluation of this novel pump concept and potential applications.

scholarly journals A Sprayed Graphene Pattern-Based Flexible Strain Sensor with High Sensitivity and Fast Response

Sensors ◽  
2019 ◽  
Vol 19 (5) ◽  
pp. 1077 ◽  
Author(s):  
Wei Xu ◽  
Tingting Yang ◽  
Feng Qin ◽  
Dongdong Gong ◽  
Yijia Du ◽  
...  
Keyword(s):  
Strain Sensor ◽  
High Sensitivity ◽  
Fast Response ◽  
Strain Sensors ◽  
Biomedical Science ◽  
Gauge Factor ◽  
Experimental Conditions ◽  
Simple Method ◽  
Wide Range ◽  
Flexible Strain Sensor

Flexible strain sensors have a wide range of applications in biomedical science, aerospace industry, portable devices, precise manufacturing, etc. However, the manufacturing processes of most flexible strain sensors previously reported have usually required high manufacturing costs and harsh experimental conditions. Besides, research interests are often focused on improving a single attribute parameter while ignoring others. This work aims to propose a simple method of manufacturing flexible graphene-based strain sensors with high sensitivity and fast response. Firstly, oxygen plasma treats the substrate to improve the interfacial interaction between graphene and the substrate, thereby improving device performance. The graphene solution is then sprayed using a soft PET mask to define a pattern for making the sensitive layer. This flexible strain sensor exhibits high sensitivity (gauge factor ~100 at 1% strain), fast response (response time: 400–700 μs), good stability (1000 cycles), and low overshoot (<5%) as well. Those processes used are compatible with a variety of complexly curved substrates and is expected to broaden the application of flexible strain sensors.

Design, Fabrication and Calibration of Heat Transfer Gauges for Transient Measurement

2010 ◽  
Author(s):  
Rakesh Kumar ◽  
Niranjan Sahoo ◽  
Vinayak Kulkarni
Keyword(s):  
Thin Film ◽  
Heat Transfer ◽  
High Speed ◽  
Internal Combustion Engines ◽  
Fast Response ◽  
Surface Heat ◽  
Heat Fluxes ◽  
Temperature History ◽  
Heating Rates ◽  
Experimental Conditions

Transient measurements of surface heating rates are very important in many applications in the field of internal combustion engines, gas turbine engines, fluidized beds and high-speed flow environments. In most surface heat transfer mapping, very fast response sensors are used for dynamic temperature measurements in the flow. The surface heat fluxes are then estimated from the temperature history, analytically/numerically by various heat transfers modeling. Thin film gauges and thermocouples are most cost effective temperature sensors for dynamic measurements because the response time of these sensors are in the range of microseconds. The production of heat transfer gauges in the laboratory has always been an art rather than a method of manufacture. The present work is aimed at design and fabrication of fast response thermocouples and thin film gauges (TFG) in the laboratory. Three types of thermocouples have been fabricated (E-type, T-type and K-type) whereas platinum film is deposited on the insulating substrate (Pyrex and Macor) for thin film heat transfer gauge. Both thermocouples and thin film gauges are calibrated under same experimental conditions.

scholarly journals Impact of low NOx strategies on holistic emission reduction from a CI engine over transient conditions

2020 ◽  
pp. 146808742097388
Author(s):  
Adriaan van Niekerk ◽  
Benjamin Drew ◽  
Neil Larsen ◽  
Peter Kay
Keyword(s):  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Pilot Injection ◽  
Test Bed ◽  
Compression Ignition Engine ◽  
Fuel Blend ◽  
Wide Range ◽  
Main Injection ◽  
The Uk ◽  
Gas Recirculation

The use of biofuels to replace fossil fuels as well as more stringent emission regulations for internal combustion engines cause a challenge for the engine manufacturers to build engines that can cope with a wide range of fuels, but still offer low exhaust emissions with no detriment to performance. In this work a test bed with a compression ignition engine has been used to measure emissions when using a ternary fuel blend between diesel, biodiesel and ethanol together with exhuast gas recirculation (EGR) and different fuel delivery techniques. EGR with biofuels have the potential to significantly reduce NOx over conventional diesel combustion. The fuel used, B2E9 achieves a 10% renewable content as set out in the UK government’s Renewable Energy Directive. Most studies reported in the literature evaluates emissions reduction technologies by only changing one factor-at-a-time at steady state conditions. This paper addresses these issues and presents a methodology utilising a Central Composite Design (CCD) analysis to optimise four engine parameters which include EGR percentage, main injection SOI, pilot injection SOI and pilot injection open duration over a transient drive cycle (WLTP) which makes the results more applicable to real world driving conditions. The optimisation of the CCD showed that NOx emissions decreases by 25% when the maximum exhaust gas recirculation is set to 45%, the main injection is retarded by 2 CADs, the pilot injection dwell time is set to 21 CADs and 24% of the fuel is delivered through the pilot injection. CO emissions increase by approximately 47% as a result of the decrease in NOx emissions.

An Improved Generalized Model for Predicting Frost Growth on a Cold Flat Plate

2010 ◽  
Author(s):  
Q. C. Guo ◽  
W. Wang ◽  
J. Xiao ◽  
W. P. Lu
Keyword(s):  
Experimental Data ◽  
Flat Plate ◽  
Current Model ◽  
Theoretical Models ◽  
Maximum Error ◽  
Open Loop ◽  
Experimental Conditions ◽  
Wide Range ◽  
Semi Empirical ◽  
Frost Growth

A generalized quasi-steady and one-dimensional model for predicting the frost growth on flat plate was proposed based on the previous theoretical models. To improve the predicting ability of the current model, a modified semi-empirical correlation for calculating initial condition of frost density was presented experimentally. The experiments were conducted in a suction-type open-loop wind tunnel under a series of experimental conditions: air temperature −8°C to 19°C, humidity 42% to 80%, velocity 5m/s and the temperature of cold plate −16°C to −8°C. The numerical results of frost thickness, frost density, frost surface temperature and heat flux rate were compared to the experimental data. The simulation results were found agree with the experimental results in a maximum error of 10%. The presented model was further validated by comparing with the previous published experimental data in a wide range of frosting conditions. It was found that the presented model was a simple but universal one to predict the frost growth on cold flat plate.

LIQUIDUS THERMO-BAROMETER FOR THE MODELING OF MAGNETITE — MELT EQUILIBRIUM

2018 ◽  
pp. 71-80
Author(s):  
N. S. Aryaeva ◽  
E. V. Koptev-Dvornikov ◽  
D. A. Bychkov
Keyword(s):  
Experimental Data ◽  
Liquidus Temperature ◽  
Vertical Structure ◽  
Maximum Error ◽  
Silicate Melt ◽  
System Of Equations ◽  
Wide Range ◽  
Basaltic Melts ◽  
Multidimensional Statistics

A system of equations of thermobarometer for magnetite-silicate melt equilibrium was obtained by method of multidimensional statistics of 93 experimental data of a magnetite solubility in basaltic melts. Equations reproduce experimental data in a wide range of basalt compositions, temperatures and pressures with small errors. Verification of thermobarometers showed the maximum error in liquidus temperature reproducing does not exceed ±7 °C. The level of cumulative magnetite appearance in the vertical structure of Tsypringa, Kivakka, Burakovsky intrusions predicted with errors from ±10 to ±50 m.

Strongly Coupled Redox-Linked Conformational Switching at the Active Site of the Non-Heme Iron-Dependent Dioxygenase, TauD

2019 ◽  
Author(s):  
Christopher John ◽  
Greg M. Swain ◽  
Robert P. Hausinger ◽  
Denis A. Proshlyakov
Keyword(s):  
Active Site ◽  
Structural Model ◽  
Heme Iron ◽  
Chemical Transformations ◽  
Experimental Conditions ◽  
Strongly Coupled ◽  
Non Heme Iron ◽  
Reversible Redox ◽  
Wide Range ◽  
Complex Structural

2-Oxoglutarate (2OG)-dependent dioxygenases catalyze C-H activation while performing a wide range of chemical transformations. In contrast to their heme analogues, non-heme iron centers afford greater structural flexibility with important implications for their diverse catalytic mechanisms. We characterize an <i>in situ</i> structural model of the putative transient ferric intermediate of 2OG:taurine dioxygenase (TauD) by using a combination of spectroelectrochemical and semi-empirical computational methods, demonstrating that the Fe (III/II) transition involves a substantial, fully reversible, redox-linked conformational change at the active site. This rearrangement alters the apparent redox potential of the active site between -127 mV for reduction of the ferric state and 171 mV for oxidation of the ferrous state of the 2OG-Fe-TauD complex. Structural perturbations exhibit limited sensitivity to mediator concentrations and potential pulse duration. Similar changes were observed in the Fe-TauD and taurine-2OG-Fe-TauD complexes, thus attributing the reorganization to the protein moiety rather than the cosubstrates. Redox difference infrared spectra indicate a reorganization of the protein backbone in addition to the involvement of carboxylate and histidine ligands. Quantitative modeling of the transient redox response using two alternative reaction schemes across a variety of experimental conditions strongly supports the proposal for intrinsic protein reorganization as the origin of the experimental observations.

scholarly journals Low-Energy Electron Damage to Condensed-Phase DNA and Its Constituents

2021 ◽  
Vol 22 (15) ◽  
pp. 7879
Author(s):  
Yingxia Gao ◽  
Yi Zheng ◽  
Léon Sanche
Keyword(s):  
Condensed Phase ◽  
Genetic Material ◽  
High Energy ◽  
Dna Lesions ◽  
Low Energy ◽  
Experimental Investigations ◽  
Experimental Conditions ◽  
Strand Breaks ◽  
Sequence Of Events ◽  
Wide Range

The complex physical and chemical reactions between the large number of low-energy (0–30 eV) electrons (LEEs) released by high energy radiation interacting with genetic material can lead to the formation of various DNA lesions such as crosslinks, single strand breaks, base modifications, and cleavage, as well as double strand breaks and other cluster damages. When crosslinks and cluster damages cannot be repaired by the cell, they can cause genetic loss of information, mutations, apoptosis, and promote genomic instability. Through the efforts of many research groups in the past two decades, the study of the interaction between LEEs and DNA under different experimental conditions has unveiled some of the main mechanisms responsible for these damages. In the present review, we focus on experimental investigations in the condensed phase that range from fundamental DNA constituents to oligonucleotides, synthetic duplex DNA, and bacterial (i.e., plasmid) DNA. These targets were irradiated either with LEEs from a monoenergetic-electron or photoelectron source, as sub-monolayer, monolayer, or multilayer films and within clusters or water solutions. Each type of experiment is briefly described, and the observed DNA damages are reported, along with the proposed mechanisms. Defining the role of LEEs within the sequence of events leading to radiobiological lesions contributes to our understanding of the action of radiation on living organisms, over a wide range of initial radiation energies. Applications of the interaction of LEEs with DNA to radiotherapy are briefly summarized.

scholarly journals Review of the Upright Balance Assessment Based on the Force Plate

2021 ◽  
Vol 18 (5) ◽  
pp. 2696
Author(s):  
Baoliang Chen ◽  
Peng Liu ◽  
Feiyun Xiao ◽  
Zhengshi Liu ◽  
Yong Wang
Keyword(s):  
Postural Balance ◽  
Force Plate ◽  
Assessment Method ◽  
Balance Assessment ◽  
Experimental Conditions ◽  
Methodological Research ◽  
Assessment Tests ◽  
Wide Range ◽  
Foot Posture ◽  
Plate System

Quantitative assessment is crucial for the evaluation of human postural balance. The force plate system is the key quantitative balance assessment method. The purpose of this study is to review the important concepts in balance assessment and analyze the experimental conditions, parameter variables, and application scope based on force plate technology. As there is a wide range of balance assessment tests and a variety of commercial force plate systems to choose from, there is room for further improvement of the test details and evaluation variables of the balance assessment. The recommendations presented in this article are the foundation and key part of the postural balance assessment; these recommendations focus on the type of force plate, the subject’s foot posture, and the choice of assessment variables, which further enriches the content of posturography. In order to promote a more reasonable balance assessment method based on force plates, further methodological research and a stronger consensus are still needed.

Sign in / Sign up

Export Citation Format

Share Document