Simulation of Fuel/Air Premixing Under the Effects of Acoustic Forcing

2004 ◽  
Author(s):  
Paul R. Van Slooten ◽  
Ravi K. Madabhushi ◽  
John H. Stufflebeam ◽  
Jeffrey Lienau
Keyword(s):  
Time Delays ◽  
Flux Ratio ◽  
Navier Stokes ◽  
Air Distribution ◽  
Thermoacoustic Instabilities ◽  
Measured Time ◽  
Planar Phase ◽  
Computational Fluid Dynamics Cfd ◽  
Acoustic Forcing ◽  
Function Time

To achieve ultra-low NOx emissions in practical lean premixed combustors, a uniform spatial and temporal fuel/air distribution is required. In addition the response of the fuel/air premixer to acoustic perturbations plays a central role in the coupling of the combustion and acoustic processes that potentially lead to thermoacoustic instabilities. In this paper, results from the simulation of a fuel/air premixer with and without acoustic forcing are reported. An unsteady Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) code is used in the simulations and the computed results are compared with data obtained using a synchronous PLIF technique. Planar phase-locked images of the fuel/air distribution during the forcing cycle are measured from which the planar averaged (bulk) fuel/air ratio “signal” is obtained. The fuel/air ratio to velocity transfer function (time delay and magnitude) at a specific forcing frequency is computed corresponding to a given jet-to-air momentum flux ratio. The comparisons between the computed and measured time delays are quite good, while the magnitude comparisons are currently inconclusive.

Computational Fluid Dynamic Using Parallel Loop of Multi-Cores Processor

2014 ◽  
Vol 493 ◽  
pp. 80-85 ◽  
Author(s):  
C.L Siow ◽  
Jaswar ◽  
Efi Afrizal
Keyword(s):  
Fluid Flow ◽  
Early Stage ◽  
Fluid Dynamic ◽  
Visual Basic ◽  
Computer Hardware ◽  
Navier Stokes ◽  
Computer Memory ◽  
Large Size ◽  
Computational Fluid Dynamics Cfd ◽  
Reynolds Average

Computational Fluid Dynamics (CFD) software is often used to study fluid flow and structures motion in fluids. The CFD normally requires large size of arrays and computer memory and then caused long execution time. However, Innovation of computer hardware such as multi-cores processor provides an alternative solution to improve this programming performance. This paper discussed loop parallelize multi-cores processor for optimization of sequential looping CFD code. This loop parallelize CFD was achieved by applying multi-tasking or multi-threading code into the original CFD code which was developed by one of the authors. The CFD code was developed based on Reynolds Average Navier-Stokes (RANS) method. The new CFD code program was developed using Microsoft Visual Basic (VB) programming language. In the early stage, the whole CFD code was constructed in a sequential flow before it is modified to parallel flow by using VBs multi-threading library. In the comparison, fluid flow around the hull of round-shaped FPSO was selected to compare the performance of both the programming codes. Besides, executed results of this self-developed code such as pressure distribution around the hull were also presented in this paper.

Analysis of Hydrodynamic Characteristics in the Process of Autonomous Underwater Vehicle Docking

2015 ◽  
Author(s):  
Xiaoxu Du ◽  
Huan Wang
Keyword(s):  
Drag Coefficient ◽  
Autonomous Underwater Vehicle ◽  
Simple Algorithm ◽  
Underwater Vehicle ◽  
Navier Stokes ◽  
Hydrodynamic Characteristics ◽  
Successful Operation ◽  
Underwater Docking ◽  
Computational Fluid Dynamics Cfd ◽  
Volume Method

The successful operation of an Autonomous Underwater Vehicle (AUV) requires the capability to return to a dock. A number of underwater docking technologies have been proposed and tested in the past. The docking allows the AUV to recharge its batteries, download data and upload new instructions, which is helpful to improve the working time and efficiency. During the underwater docking process, unsteady hydrodynamic interference occurs between the docking device and an AUV. To ensure a successful docking, it is very important that the underwater docking hydrodynamics of AUV is understood. In this paper, numerical simulations based on the computational fluid dynamics (CFD) solutions were carried out for a 1.85m long AUV with maximum 0.2 m in diameter during the docking process. The two-dimensional AUV model without fin and rudder was used in the simulation. The mathematical model based on the Reynolds-averaged Navier-Stokes (RANS) equations was established. The finite volume method (FVM) and the dynamic structured mesh technique were used. SIMPLE algorithm and the k-ε turbulence model in the Descartes coordinates were also adopted. The hydrodynamics characteristics of different docking states were analyzed, such as the different docking velocity, the docking device including baffle or not. The drag coefficients of AUV in the process of docking were computed for various docking conditions, i.e., the AUV moving into the docking in the speed of 1m/s, 2m/s, 5m/s. The results indicate that the drag coefficient increases slowly in the process of AUV getting close to the docking device. When the AUV moves into the docking device, the drag coefficient increases rapidly. Then the drag coefficient decreases rapidly. The drag coefficient decreases with the increase of velocity when AUV enters the docking device. It was also found that the drag coefficient can be effectively reduced by dislodging the baffle of docking device.

Modeling of Compressor Drum Cavities With Radial Inflow

2016 ◽  
Author(s):  
D. Amirante ◽  
Z. Sun ◽  
J. W. Chew ◽  
N. J. Hills ◽  
N. R. Atkins
Keyword(s):  
Thermal Stratification ◽  
Turbulence Modeling ◽  
Navier Stokes ◽  
Inflow Rate ◽  
Cfd Models ◽  
Flow And Heat Transfer ◽  
Rotating Discs ◽  
Computational Fluid Dynamics Cfd ◽  
Inlet Conditions ◽  
Cooling Air

Reynolds-Averaged Navier-Stokes (RANS) computations have been conducted to investigate the flow and heat transfer between two co-rotating discs with an axial throughflow of cooling air and a radial bleed introduced from the shroud. The computational fluid dynamics (CFD) models have been coupled with a thermal model of the test rig, and the predicted metal temperature compared with the thermocouple data. CFD solutions are shown to vary from a buoyancy driven regime to a forced convection regime, depending on the radial inflow rate prescribed at the shroud. At a high radial inflow rate, the computations show an excellent agreement with the measured temperatures through a transient rig condition. At a low radial inflow rate, the cavity flow is destabilized by the thermal stratification. Good qualitative agreement with the measurements is shown, although a significant over-prediction of disc temperatures is observed. This is associated with under prediction of the penetration of the axial throughflow into the cavity. The mismatch could be the result of strong sensitivity to the prescribed inlet conditions, in addition to possible shortcomings in the turbulence modeling.

Numerical Simulation of Indoor Thermal Environment of a Double-Skin Facade Office with Different Shutter Angles

2014 ◽  
Vol 694 ◽  
pp. 256-259
Author(s):  
Xin Zhan ◽  
Hua Yang ◽  
Feng Yun Jin
Keyword(s):  
Heat Transfer ◽  
Thermal Environment ◽  
Ventilation Rate ◽  
Air Distribution ◽  
Indoor Thermal Environment ◽  
Double Skin ◽  
Computational Fluid Dynamics Cfd ◽  
Heat Transfer Simulation ◽  
Shading Devices ◽  
Rng Turbulence Model

Airflow and heat transfer simulation was conducted for a double-skin façade (DSF) system equipped with shading devices in the cavity, using computational fluid dynamics (CFD) with RNG turbulence model and PISO algorithm, for five conditions of slat angles (θ=0°, 30°, 45°, 60°, 90°). The present study indicates that the presence of shading devices influences the temperatures, the ventilation rate and the air distribution in the DSF system. Besides, the different angles will make different influences.

Mechanism and Flow Control on the Mismatching of Impeller and Vaned Diffuser Caused by Inlet Prewhirl for Centrifugal Compressors

2016 ◽  
Author(s):  
Qiangqiang Huang ◽  
Xinqian Zheng ◽  
Aolin Wang
Keyword(s):  
Flow Control ◽  
Control Method ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Vaned Diffuser ◽  
Inlet Distortion ◽  
Computational Fluid Dynamics Cfd ◽  
Stagger Angle ◽  
Good Agreement ◽  
Matching Relation

Air often flows into compressors with inlet prewhirl, because it will obtain a circumferential component of velocity via inlet distortion or swirl generators such as inlet guide vanes. A lot of research has shown that inlet prewhirl does influence the characteristics of components, but the change of the matching relation between the components caused by inlet prewhirl is still unclear. This paper investigates the influence of inlet prewhirl on the matching of the impeller and the diffuser and proposes a flow control method to cure mismatching. The approach combines steady three-dimensional Reynolds-averaged Navier-Stokes (RANS) simulations with theoretical analysis and modeling. The result shows that a compressor whose impeller and diffuser match well at zero prewhirl will go to mismatching at non-zero prewhirl. The diffuser throat gets too large to match the impeller at positive prewhirl and gets too small for matching at negative prewhirl. The choking mass flow of the impeller is more sensitive to inlet prewhirl than that of the diffuser, which is the main reason for the mismatching. To cure the mismatching via adjusting the diffuser vanes stagger angle, a one-dimensional method based on incidence matching has been proposed to yield a control schedule for adjusting the diffuser. The optimal stagger angle predicted by analytical method has good agreement with that predicted by computational fluid dynamics (CFD). The compressor is able to operate efficiently in a much broader flow range with the control schedule. The flow range, where the efficiency is above 80%, of the datum compressor and the compressor only employing inlet prewhirl and no control are just 25.3% and 31.8%, respectively. For the compressor following the control schedule, the flow range is improved up to 46.5%. This paper also provides the perspective of components matching to think about inlet distortion.

The Effect of Turbulence and Real Gas Models on the Two Phase Spontaneously Condensing Flows in Nozzle

2013 ◽  
Author(s):  
Yogini Patel ◽  
Giteshkumar Patel ◽  
Teemu Turunen-Saaresti
Keyword(s):  
Fluid Dynamics ◽  
Experimental Data ◽  
Nucleation Theory ◽  
Classical Nucleation Theory ◽  
Navier Stokes ◽  
Two Phase ◽  
Real Gas ◽  
Spontaneous Condensation ◽  
Condensing Flows ◽  
Computational Fluid Dynamics Cfd

The aim of the paper is to analyse the effect of turbulence and real gas models on the process of spontaneous condensation in converging diverging (CD) nozzle by using commercial Computational Fluid Dynamics (CFD) code. The calculations were based on the 2-D compressible Navier-Stokes (NS) equations coupled with two-equation turbulence model, and the non-equilibrium spontaneous condensing steam flow was solved on the basis of the classical nucleation theory. The results were validated to the available experimental data.

scholarly journals Three-Dimensional Navier–Stokes Analysis and Redesign of an Imbedded Bellmouth Nozzle in a Turbine Cascade Inlet Section

1996 ◽  
Vol 118 (3) ◽  
pp. 529-535 ◽  
Author(s):  
P. W. Giel ◽  
J. R. Sirbaugh ◽  
I. Lopez ◽  
G. J. Van Fossen
Keyword(s):  
Three Dimensional ◽  
Navier Stokes ◽  
Experimental Measurements ◽  
Inlet Section ◽  
Turbine Cascade ◽  
Blade Cascade ◽  
Inlet Geometry ◽  
Computational Fluid Dynamics Cfd ◽  
Transonic Turbine ◽  
Flow Nonuniformity

Experimental measurements in the inlet of a transonic turbine blade cascade showed unacceptable pitchwise flow nonuniformity. A three-dimensional, Navier–Stokes computational fluid dynamics (CFD) analysis of the imbedded bellmouth inlet in the facility was performed to identify and eliminate the source of the flow nonuniformity. The blockage and acceleration effects of the blades were accounted for by specifying a periodic static pressure exit condition interpolated from a separate three-dimensional Navier–Stokes CFD solution of flow around a single blade in an infinite cascade. Calculations of the original inlet geometry showed total pressure loss regions consistent in strength and location to experimental measurements. The results indicate that the distortions were caused by a pair of streamwise vortices that originated as a result of the interaction of the flow with the imbedded bellmouth. Computations were performed for an inlet geometry that eliminated the imbedded bellmouth by bridging the region between it and the upstream wall. This analysis indicated that eliminating the imbedded bellmouth nozzle also eliminates the pair of vortices, resulting in a flow with much greater pitchwise uniformity. Measurements taken with an installed redesigned inlet verify that the flow nonuniformity has indeed been eliminated.

A Verification and Validation Study of CFD Simulation of Wind-Induced Ventilation on Building with Single-Sided Opening

2014 ◽  
Vol 554 ◽  
pp. 696-700 ◽  
Author(s):  
Nur Farhana Mohamad Kasim ◽  
Sheikh Ahmad Zaki ◽  
Mohamed Sukri Mat Ali ◽  
Ahmad Faiz Mohammad ◽  
Azli Abd Razak
Keyword(s):  
Open Source Software ◽  
Natural Ventilation ◽  
Cfd Simulation ◽  
Previous Experiment ◽  
Experimental Methods ◽  
Verification And Validation ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Computational Fluid Dynamics Cfd ◽  
Model Approach

Wind-induced ventilation is widely acknowledged as one of the best approaches for inducing natural ventilation. Computational fluid dynamics (CFD) technique is gaining popularity among researchers as an alternative for experimental methods to investigate the behavior of wind-driven ventilation in building. In this present paper, Reynolds averaged Navier-Stokes equation (RANS) k-ε model approach is considered to simulate the airflow on a simplified cubic building with an opening on a single façade. Preliminary simulation using models from previous experiment indicates the reliability of OpenFOAM, the open source software that will be used in this study. The results obtained in this study will better define options for our future study which aims to explore how different buildings arrays modify the airflow inside and around a naturally ventilated building.

Effects of Downstream Vane Bowing and Asymmetry on Unsteadiness in a Transonic Turbine

2018 ◽  
Author(s):  
John P. Clark ◽  
Richard J. Anthony ◽  
Michael K. Ooten ◽  
John M. Finnegan ◽  
P. Dean Johnson ◽  
...  
Keyword(s):  
Turbine Blades ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Time Resolved ◽  
Turbine Engine ◽  
Shock Interactions ◽  
Design Changes ◽  
Post Test ◽  
Measured Time ◽  
Transonic Turbine

Accurate predictions of unsteady forcing on turbine blades are essential for the avoidance of high-cycle-fatigue issues during turbine engine development. Further, if one can demonstrate that predictions of unsteady interaction in a turbine are accurate, then it becomes possible to anticipate resonant-stress problems and mitigate them through aerodynamic design changes during the development cycle. A successful reduction in unsteady forcing for a transonic turbine with significant shock interactions due to downstream components is presented here. A pair of methods to reduce the unsteadiness was considered and rigorously analyzed using a three-dimensional, time resolved Reynolds-Averaged Navier Stokes (RANS) solver. The first method relied on the physics of shock reflections itself and involved altering the stacking of downstream components to achieve a bowed airfoil. The second method considered was circumferentially-asymmetric vane spacing which is well known to spread the unsteadiness due to vane-blade interaction over a range of frequencies. Both methods of forcing reduction were analyzed separately and predicted to reduce unsteady pressures on the blade as intended. Then, both design changes were implemented together in a transonic turbine experiment and successfully shown to manipulate the blade unsteadiness in keeping with the design-level predictions. This demonstration was accomplished through comparisons of measured time-resolved pressures on the turbine blade to others obtained in a baseline experiment that included neither asymmetric spacing nor bowing of the downstream vane. The measured data were further compared to rigorous post-test simulations of the complete turbine annulus including a bowed downstream vane of non-uniform pitch.

scholarly journals Experimental Validation Data for Computational Fluid Dynamics of Forced Convection on a Vertical Flat Plate

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Jeff R. Harris ◽  
Blake W. Lance ◽  
Barton L. Smith
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Forced Convection ◽  
Vertical Plate ◽  
Navier Stokes ◽  
Validation Dataset ◽  
System Response ◽  
Cfd Validation ◽  
Validation Data ◽  
Computational Fluid Dynamics Cfd

A computational fluid dynamics (CFD) validation dataset for turbulent forced convection on a vertical plate is presented. The design of the apparatus is based on recent validation literature and provides a means to simultaneously measure boundary conditions (BCs) and system response quantities (SRQs). All important inflow quantities for Reynolds-Averaged Navier-Stokes (RANS). CFD are also measured. Data are acquired at two heating conditions and cover the range 40,000 < Rex < 300,000, 357 <  Reδ2 < 813, and 0.02 < Gr/Re2 < 0.232.

Sign in / Sign up

Export Citation Format

Share Document