Validation of Steady Average-Passage and Mixing Plane CFD Approaches for the Performance Prediction of a Modern Gas Turbine Multistage Axial Compressor

2008 ◽  
Author(s):  
Mahmoud L. Mansour ◽  
John Gunaraj ◽  
Shraman Goswami
Keyword(s):  
Flow Field ◽  
Turbulence Modeling ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Turbulence Models ◽  
Leading Edge ◽  
Sensitivity Study ◽  
Leakage Flow ◽  
Overall Performance

This paper summarizes the results of a validation and calibration study for two modern Computational Fluid Dynamics programs that are capable of modeling multistage axial compressors in a multi-blade row environment. The validation test case is a modern 4-stage high pressure ratio axial compressor designed and tested by Honeywell Aerospace in the late 90’s. The two CFD programs employ two different techniques for simulating the steady three-dimensional viscous flow field in a multistage/multiblade row turbo-machine. The first code, APNASA, was developed by NASA Glenn Research Center “GRC” and applies the approach by Adamczyk [1] for solving the average-passage equations which is a time and passage-averaged version of the Reynolds Averaged Navier Stokes (RANS) equations. The second CFD code is commercially marketed by ANSYS-CFX and applies a much simpler approach, known as the mixing-plane model, for combining the relative and the stationary frames of reference in a single steady 3D viscous simulation. Results from the two CFD programs are compared against the tested compressor’s overall performance data and against measured flow profiles at the leading edge of the fourth stator. The paper also presents a turbulence modeling sensitivity study aimed at documenting the sensitivity of the prediction of the flow field of such compressors to use of different turbulence closures such as the standard K-ε model, the Wilcox K-ω model and the Shear-Stress-Transport K-ω/SST turbulence model. The paper also presents results that demonstrate the CFD prediction sensitivity to modeling the compressor’s hub leakages from the inner-banded stator cavities. Comparison to the test data, using the K-ε turbulence closure, show that APNASA provides better accuracy in predicting the absolute levels of the performance characteristics. The presented results also show that better predictions by CFX can be obtained using the K-ω and the SST turbulence models. Modeling of the hub leakage flow was found to have significant and more than expected impact on the compressor predicted overall performance. The authors recommend further validation and evaluation for the modeling of the hub leakage flow to ensure realistic predictions for turbo-machinery performance.

scholarly journals Investigation of Seal Cavity Leakage Flow Effect on Multistage Axial Compressor Aerodynamic Performance with a Circumferentially Averaged Method

2021 ◽  
Vol 11 (9) ◽  
pp. 3937
Author(s):  
Dong Liang ◽  
Donghai Jin ◽  
Xingmin Gui
Keyword(s):  
Flow Field ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Work Capacity ◽  
Leakage Flow ◽  
Multistage Compressor ◽  
And Migration ◽  
Flow Blockage

The seal cavity leakage flow has a considerable impact on the performance of the aeroengine, especially on the multistage compressor. Thus, a quasi-three-dimensional simulation program named CAM is developed basing on circumferentially averaged throughflow method. The program enables a rapid diagnosis for the performance degradation of multistage compressor caused by labyrinth wear. The coupling flow field between the seal cavity leakage flow and the main flow field at the root of the shrouded stator of a high-loading three-stage compressor with inlet guide vanes (IGV) was simulated by CAM and the results indicate that seal cavity leakage flow has a significant impact on the overall performance of the compressor. That is, for a 1% increase in the seal-tooth clearance-to-span ratio, the decrease in total pressure ratio was 2.6%, and the reduction in efficiency was 0.6%. Stage performance shows that the seal cavity leakage flow reduces the pressurization capacity of the current stator and the work capacity of the downstream rotor, but has little effect on the upstream blade row. Spanwise distribution of blade element performance shows that the leakage flow leads to an increased flow blockage near the hub, resulting in spanwise migration. The incidence of the stator and rear rotor then change through the entire span. The leakage flow leads to the flow blockage and migration and hence changes the incidence angle, which results in the deterioration of compressor performance.

scholarly journals Influence of Seal Cavity Leakage Flow on Compressor Performance Investigated with a Circumferentially Averaged Method

2021 ◽  
Vol 11 (2) ◽  
pp. 780
Author(s):  
Dong Liang ◽  
Xingmin Gui ◽  
Donghai Jin
Keyword(s):  
Flow Field ◽  
Pressure Ratio ◽  
Interaction Mechanism ◽  
Main Flow ◽  
Leakage Flow ◽  
Destructive Effect ◽  
Through Flow ◽  
Compressor Performance ◽  
Overall Performance ◽  
Flow Blockage

In order to investigate the effect of seal cavity leakage flow on a compressor’s performance and the interaction mechanism between the leakage flow and the main flow, a one-stage compressor with a cavity under the shrouded stator was numerically simulated using an inhouse circumferentially averaged through flow program. The leakage flow from the shrouded stator cavity was calculated simultaneously with main flow in an integrated manner. The results indicate that the seal cavity leakage flow has a significant impact on the overall performance of the compressor. For a leakage of 0.2% of incoming flow, the decrease in the total pressure ratio was 2% and the reduction of efficiency was 1.9 points. Spanwise distribution of the flow field variables of the shrouded stator shows that the leakage flow leads to an increased flow blockage near the hub, resulting in drop of stator performance, as well as a certain destructive effect on the flow field of the main passage.

Experimental and Numerical Investigation of the Unsteady Leakage Flow Through the Rotor Tip Labyrinth of a 1.5-Stage Axial Turbine

2005 ◽  
Author(s):  
K. Wolter ◽  
A. Giboni ◽  
P. Peters ◽  
J. R. Menter ◽  
H. Pfost
Keyword(s):  
Flow Field ◽  
Flow Direction ◽  
Three Dimensional ◽  
Calculated Data ◽  
Leading Edge ◽  
Numerical Data ◽  
Potential Effect ◽  
Main Flow ◽  
Leakage Flow ◽  
Axial Turbine

This paper presents the results of unsteady probe measurements and numerical flow calculations in a 1.5-stage low speed axial turbine with a straight labyrinth seal on a rotor shroud. The unsteady development of the leakage flow in the three cavities is described and analysed in detail. For the investigation of the leakage flow detailed time-accurate measurements of the three-dimensional flow field were carried out in five measurement planes from casing to the rotor shroud over more than one pitch. These measurements were carried out with a miniature pneumatic five-hole probe and miniature triple hot-wire probes. Both probes have a spherical head for better adjustment in flow direction. The high resolution of 330 measurement points in each of the five measurement planes represents the flow field in great detail. The unsteady experimental data was compared with the results of the unsteady numerical simulation of the turbine flow, calculated by the 3D-Navier-Stokes Solver CFX-TASCflow. The calculated data correspond well with the experimental results and allow a detailed analysis of the flow in the cavities of the labyrinth. As demonstrated in this paper the investigations show that the leakage flow at the inlet ant outlet of the labyrinth is strongly influenced by the different positions of the rotor to the stator. The unsteady experimental and numerical data indicates intensive effects of the leakage flow caused and influenced by the trailing edge of the first stator and the potential effect of the rotor leading edge. An intensive vortex develops depending on the rotor position in the first cavity. This vortex is also influenced by a small corner vortex above the axial inlet gap of the labyrinth. After the fins this unsteady influence of the leakage flow decreases and below the jet a large vortex moves in circumferential direction. The intensity of this circulation vortex is reduced at the end of the last cavity due to the interaction with the main flow and the flow direction out of the labyrinth. Therefore the unsteady behaviour of the leakage flow grows up, which is also caused by its uneven entry into the main flow.

Unsteady Three-Dimensional Flow Phenomena Due to Breakdown of Tip Leakage Vortex in a Transonic Axial Compressor Rotor

2004 ◽  
Author(s):  
K. Yamada ◽  
M. Furukawa ◽  
T. Nakano ◽  
M. Inoue ◽  
K. Funazaki
Keyword(s):  
Shock Wave ◽  
Flow Field ◽  
Vortex Breakdown ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor

Unsteady three-dimensional flow fields in a transonic axial compressor rotor (NASA Rotor 37) have been investigated by unsteady Reynolds-averaged Navier-Stokes simulations. The simulations show that the breakdown of the tip leakage vortex occurs in the compressor rotor because of the interaction of the vortex with the shock wave. At near-peak efficiency condition small bubble-type breakdown of the tip leakage vortex happens periodically and causes the loading of the adjacent blade to fluctuate periodically near the leading edge. Since the blade loading near the leading edge is closely linked to the swirl intensity of the tip leakage vortex, the periodic fluctuation of the blade loading leads to the periodic breakdown of the tip leakage vortex, resulting in self-sustained flow oscillation in the tip leakage flow field. However, the tip leakage vortex breakdown is so weak and small that it is not observed in the time-averaged flow field at near-peak efficiency condition. On the other hand, spiral-type breakdown of the tip leakage vortex is caused by the interaction between the vortex and the shock wave at near-stall operating condition. The vortex breakdown is found continuously since the swirl intensity of tip leakage vortex keeps strong at near-stall condition. The spiral-type vortex breakdown has the nature of self-sustained flow oscillation and gives rise to the large fluctuation of the tip leakage flow field, in terms of shock wave location, blockage near the rotor tip and three-dimensional separation structure on the suction surface. It is found that the breakdown of the tip leakage vortex leads to the unsteady flow phenomena near the rotor tip, accompanying large blockage effect in the transonic compressor rotor at the near-stall condition.

Numerical Investigation of a Transonic Centrifugal Compressor

2006 ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Seiichi Ibaraki
Keyword(s):  
Shock Waves ◽  
Flow Field ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Tip Clearance ◽  
Complex Flow ◽  
Low Velocity ◽  
Flow Measurements

A three-dimensional Navier-Stokes solver is used to investigate the flow field of a high pressure ratio centrifugal compressor for turbocharger applications. Such a compressor consists of a double-splitter impeller followed by a vane diffuser. The inlet flow to the open shrouded impeller is transonic, thus giving rise to interactions between shock waves and boundary layers and between shock waves and tip leakage vortices. These interactions generate complex flow structures which are convected and distorted through the impeller blades. Detailed Laser Doppler Velocimetry (LDV) flow measurements are available at various cross sections inside the impeller blades highlighting the presence of low velocity flow regions near the shroud. Particular attention is focused on understanding the physical mechanisms which govern the flow phenomena in the near shroud region. To this end numerical investigations are performed using different tip clearance modelizations and various turbulence models, and their impact on the computed flow field is discussed.

Effect of Inflow Circumferential Distortion on a Transonic Axial Compressor

2017 ◽  
Author(s):  
Yuyun Li ◽  
Zhiheng Wang ◽  
Guang Xi
Keyword(s):  
Total Pressure ◽  
Rotor Blade ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Leading Edge ◽  
Inlet Distortion ◽  
Compressor Rotor ◽  
Structure Changes ◽  
Transonic Axial Compressor

The Inlet distortion, which may lead to the stability reduction or structure failure, is often non-ignorable in an axial compressor. In the paper, the three-dimensional unsteady numerical simulations on the flow in NASA rotor 67 are carried out to investigate the effect of inlet distortion on the performance and flow structure in a transonic axial compressor rotor. A sinusoidal circumferential total pressure distortion with eleven periods per revolution is adopted to study the interaction between the transonic rotor and inlet circumferential distortion. Concerning the computational expense, the flow in two rotor blade passages is calculated. Various intensities of the total pressure distortion are discussed, and the detailed flow structures under different rotating speeds near the peak efficiency condition are analyzed. It is found that the distortion has a positive effect on the flow near the hub. Even though there is no apparent decrease in the rotor efficiency or total pressure ratio, an obvious periodic loading exists over the whole blade. The blade loadings are concentrated in the region near the leading edge of the rotor blade or regions affected by the oscillating shocks near the pressure side. The time averaged location of shock structure changes little with the distortion, and the motion of shocks and the interactions between the shock and the boundary layer make a great contribution to the instability of the blade structure.

Three-Dimensional Flow Field in the Tip Region of a Compressor Rotor Passage—Part I: Mean Velocity Profiles and Annulus Wall Boundary Layer

1982 ◽  
Vol 104 (4) ◽  
pp. 760-771 ◽  
Author(s):  
B. Lakshminarayana ◽  
M. Pouagare ◽  
R. Davino
Keyword(s):  
Boundary Layer ◽  
Flow Field ◽  
Three Dimensional ◽  
Leading Edge ◽  
Leakage Flow ◽  
Suction Surface ◽  
Mean Velocity ◽  
Wall Boundary Layer ◽  
Compressor Rotor ◽  
Wall Boundary

The flow field in the annulus wall and tip region of a compressor rotor was measured using a triaxial, hot-wire probe rotating with the rotor. The flow was surveyed across the entire passage at five axial locations (leading edge, 1/4 chord, 1/2 chord, 3/4 chord, and trailing edge locations) and at six radial locations inside the passage. The data derived include all three components of mean velocity. Blade-to-blade variations of the velocity components, pitch and yaw angles, as well as the passage-averaged mean properties of the annulus wall boundary layer, are derived from this data. The measurements indicate that the leakage flow starts beyond a quarter-chord and tends to roll up farther away from the suction surface than that observed in cascades. Substantial velocity deficiencies and radial inward velocities are observed in this region. The annulus wall boundary layer is well behaved up to half a chord, beyond which interactions with the leakage flow produce complex profiles.

Experimental Study of the Flow Field Within a Transonic Axial Compressor Rotor by Laser Velocimetry and Comparison With Through-Flow Calculations

1978 ◽  
Vol 100 (2) ◽  
pp. 279-286 ◽  
Author(s):  
R. J. Dunker ◽  
P. E. Strinning ◽  
H. B. Weyer
Keyword(s):  
Flow Field ◽  
Pressure Ratio ◽  
Analytical Data ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Compressor Rotor ◽  
Through Flow ◽  
Equivalent Mass ◽  
Transonic Axial Compressor ◽  
Design Speed

The flow field ahead, within, and behind the rotor of a transonic axial compressor designed for a total pressure ratio of 1.51 at a relative tip Mach number of 1.4 has been studied in detail using an advanced laser velocimeter. The tests were carried out at 70 and 100 percent design speed (20,260 rpm) and equivalent mass flows corresponding to the point of maximum isentropic efficiency. The tests yielded quite complete data on the span- and gap-wise velocity profiles, on the three-dimensional shock waves in and outside of the rotor blade channels, and on the blade wakes. Some of the experimental results will be submitted, discussed, and compared to corresponding analytical data of a through-flow calculation. The comparison reveals considerable discrepancies inside the blade row between the two-dimensional calculation and the experiments primarily due to the loss and deviation correlations used, as well as to the distribution of losses and flow angles inside the blade channels.

The Impact of Manufacturing Variations on Performance of a Transonic Axial Compressor Rotor

2020 ◽  
Vol 142 (8) ◽  
Author(s):  
Marcus Lejon ◽  
Niklas Andersson ◽  
Lars Ellbrant ◽  
Hans Mårtensson
Keyword(s):  
Flow Field ◽  
Geometric Mean ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Leading Edge ◽  
Mean Deviation ◽  
Design Intent ◽  
Compressor Rotor ◽  
The Mean ◽  
The Impact

Abstract In this paper, the impact of manufacturing variations on performance of an axial compressor rotor is evaluated at design rotational speed. The geometric variations from the design intent obtained from measurements were used to evaluate the impact of manufacturing variations on performance and the flow field in the rotor. The complete blisk is simulated using 3D computational fluid dynamics calculations, allowing for a detailed analysis of the impact of geometric variations on the flow. It is shown that the mean shift of the geometry from the design intent is responsible for the majority of the change in performance in terms of mass flow and total pressure ratio for this specific blisk. In terms of polytropic efficiency, the measured geometric scatter is shown to have a higher influence than the geometric mean deviation. The geometric scatter around the mean is shown to impact the pressure along the leading edge and the shock position. Furthermore, a blisk is analyzed with one blade deviating substantially from the design intent. It is shown that the impact of this blade on the flow is largely limited to the blade passages that it is directly a part of. It is also shown that the impact of this blade on the flow field can be represented by a simulation including three blade passages. In terms of loss, using five blade passages is shown to give a close estimate for the relative change in loss for the blade deviating substantially from the design intent and for the neighboring blades.

Analysis of the Interrow Flow Field Within a Transonic Axial Compressor: Part 2—Unsteady Flow Analysis

2000 ◽  
Vol 123 (1) ◽  
pp. 57-63 ◽  
Author(s):  
Xavier Ottavy ◽  
Isabelle Tre´binjac ◽  
Andre´ Vouillarmet
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Leading Edge ◽  
Rotor Blades ◽  
Time Averaging ◽  
Order Of Magnitude ◽  
Transonic Axial Compressor

An analysis of the experimental data, obtained by laser two-focus anemometry in the IGV-rotor interrow region of a transonic axial compressor, is presented with the aim of improving the understanding of the unsteady flow phenomena. A study of the IGV wakes and of the shock waves emanating from the leading edge of the rotor blades is proposed. Their interaction reveals the increase in magnitude of the wake passing through the moving shock. This result is highlighted by the streamwise evolution of the wake vorticity. Moreover, the results are analyzed in terms of a time-averaging procedure and the purely time-dependent velocity fluctuations that occur are quantified. It may be concluded that they are of the same order of magnitude as the spatial terms for the inlet rotor flow field. That shows that the temporal fluctuations should be considered for the three-dimensional rotor time-averaged simulations.

Sign in / Sign up

Export Citation Format

Share Document