scholarly journals Investigation of Seal Cavity Leakage Flow Effect on Multistage Axial Compressor Aerodynamic Performance with a Circumferentially Averaged Method

2021 ◽  
Vol 11 (9) ◽  
pp. 3937
Author(s):  
Dong Liang ◽  
Donghai Jin ◽  
Xingmin Gui
Keyword(s):  
Flow Field ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Work Capacity ◽  
Leakage Flow ◽  
Multistage Compressor ◽  
And Migration ◽  
Flow Blockage

The seal cavity leakage flow has a considerable impact on the performance of the aeroengine, especially on the multistage compressor. Thus, a quasi-three-dimensional simulation program named CAM is developed basing on circumferentially averaged throughflow method. The program enables a rapid diagnosis for the performance degradation of multistage compressor caused by labyrinth wear. The coupling flow field between the seal cavity leakage flow and the main flow field at the root of the shrouded stator of a high-loading three-stage compressor with inlet guide vanes (IGV) was simulated by CAM and the results indicate that seal cavity leakage flow has a significant impact on the overall performance of the compressor. That is, for a 1% increase in the seal-tooth clearance-to-span ratio, the decrease in total pressure ratio was 2.6%, and the reduction in efficiency was 0.6%. Stage performance shows that the seal cavity leakage flow reduces the pressurization capacity of the current stator and the work capacity of the downstream rotor, but has little effect on the upstream blade row. Spanwise distribution of blade element performance shows that the leakage flow leads to an increased flow blockage near the hub, resulting in spanwise migration. The incidence of the stator and rear rotor then change through the entire span. The leakage flow leads to the flow blockage and migration and hence changes the incidence angle, which results in the deterioration of compressor performance.

Validation of Steady Average-Passage and Mixing Plane CFD Approaches for the Performance Prediction of a Modern Gas Turbine Multistage Axial Compressor

2008 ◽  
Author(s):  
Mahmoud L. Mansour ◽  
John Gunaraj ◽  
Shraman Goswami
Keyword(s):  
Flow Field ◽  
Turbulence Modeling ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Turbulence Models ◽  
Leading Edge ◽  
Sensitivity Study ◽  
Leakage Flow ◽  
Overall Performance

This paper summarizes the results of a validation and calibration study for two modern Computational Fluid Dynamics programs that are capable of modeling multistage axial compressors in a multi-blade row environment. The validation test case is a modern 4-stage high pressure ratio axial compressor designed and tested by Honeywell Aerospace in the late 90’s. The two CFD programs employ two different techniques for simulating the steady three-dimensional viscous flow field in a multistage/multiblade row turbo-machine. The first code, APNASA, was developed by NASA Glenn Research Center “GRC” and applies the approach by Adamczyk [1] for solving the average-passage equations which is a time and passage-averaged version of the Reynolds Averaged Navier Stokes (RANS) equations. The second CFD code is commercially marketed by ANSYS-CFX and applies a much simpler approach, known as the mixing-plane model, for combining the relative and the stationary frames of reference in a single steady 3D viscous simulation. Results from the two CFD programs are compared against the tested compressor’s overall performance data and against measured flow profiles at the leading edge of the fourth stator. The paper also presents a turbulence modeling sensitivity study aimed at documenting the sensitivity of the prediction of the flow field of such compressors to use of different turbulence closures such as the standard K-ε model, the Wilcox K-ω model and the Shear-Stress-Transport K-ω/SST turbulence model. The paper also presents results that demonstrate the CFD prediction sensitivity to modeling the compressor’s hub leakages from the inner-banded stator cavities. Comparison to the test data, using the K-ε turbulence closure, show that APNASA provides better accuracy in predicting the absolute levels of the performance characteristics. The presented results also show that better predictions by CFX can be obtained using the K-ω and the SST turbulence models. Modeling of the hub leakage flow was found to have significant and more than expected impact on the compressor predicted overall performance. The authors recommend further validation and evaluation for the modeling of the hub leakage flow to ensure realistic predictions for turbo-machinery performance.

scholarly journals Influence of Seal Cavity Leakage Flow on Compressor Performance Investigated with a Circumferentially Averaged Method

2021 ◽  
Vol 11 (2) ◽  
pp. 780
Author(s):  
Dong Liang ◽  
Xingmin Gui ◽  
Donghai Jin
Keyword(s):  
Flow Field ◽  
Pressure Ratio ◽  
Interaction Mechanism ◽  
Main Flow ◽  
Leakage Flow ◽  
Destructive Effect ◽  
Through Flow ◽  
Compressor Performance ◽  
Overall Performance ◽  
Flow Blockage

In order to investigate the effect of seal cavity leakage flow on a compressor’s performance and the interaction mechanism between the leakage flow and the main flow, a one-stage compressor with a cavity under the shrouded stator was numerically simulated using an inhouse circumferentially averaged through flow program. The leakage flow from the shrouded stator cavity was calculated simultaneously with main flow in an integrated manner. The results indicate that the seal cavity leakage flow has a significant impact on the overall performance of the compressor. For a leakage of 0.2% of incoming flow, the decrease in the total pressure ratio was 2% and the reduction of efficiency was 1.9 points. Spanwise distribution of the flow field variables of the shrouded stator shows that the leakage flow leads to an increased flow blockage near the hub, resulting in drop of stator performance, as well as a certain destructive effect on the flow field of the main passage.

Experimental Study of the Flow Field Within a Transonic Axial Compressor Rotor by Laser Velocimetry and Comparison With Through-Flow Calculations

1978 ◽  
Vol 100 (2) ◽  
pp. 279-286 ◽  
Author(s):  
R. J. Dunker ◽  
P. E. Strinning ◽  
H. B. Weyer
Keyword(s):  
Flow Field ◽  
Pressure Ratio ◽  
Analytical Data ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Compressor Rotor ◽  
Through Flow ◽  
Equivalent Mass ◽  
Transonic Axial Compressor ◽  
Design Speed

The flow field ahead, within, and behind the rotor of a transonic axial compressor designed for a total pressure ratio of 1.51 at a relative tip Mach number of 1.4 has been studied in detail using an advanced laser velocimeter. The tests were carried out at 70 and 100 percent design speed (20,260 rpm) and equivalent mass flows corresponding to the point of maximum isentropic efficiency. The tests yielded quite complete data on the span- and gap-wise velocity profiles, on the three-dimensional shock waves in and outside of the rotor blade channels, and on the blade wakes. Some of the experimental results will be submitted, discussed, and compared to corresponding analytical data of a through-flow calculation. The comparison reveals considerable discrepancies inside the blade row between the two-dimensional calculation and the experiments primarily due to the loss and deviation correlations used, as well as to the distribution of losses and flow angles inside the blade channels.

scholarly journals Laser Two-Focus Anemometry Investigation of the Flow Field Within a Supersonic Axial Compressor Rotor

1990 ◽  
Author(s):  
Isabelle Trebinjac ◽  
André Vouillarmet
Keyword(s):  
Flow Field ◽  
Comprehensive Evaluation ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Navier Stokes ◽  
Viscous Effects ◽  
Compressor Rotor ◽  
High Pressure Compressor ◽  
Good Agreement

Laser anemometer measurements have been performed within and downstream of a supersonic single-stage high-pressure compressor. At design point and with standard upstream conditions the maximum relative Mach number varies from 1.3 at the tip to 1.1 at the hub. The stage total pressure ratio is 1.84 and the specific mass flow 180 kg/s/m2. The laser two-focus anemometer has been completely designed in the Laboratory; its originality being the use of a counting technique instead of the classical multichannel analyzer one. The data acquisition and reduction procedures are presented here. A comprehensive evaluation of the global flow-field is in the scope of this paper. For that, the intra-blade flow field is described and the shock pattern is discussed. Furthermore, the experimental results are compared with both inviscid and viscous three-dimensional numerical simulations. The viscous computation is based on the Navier-Stokes solution using a mixing length turbulence model. The good agreement observed in this last case shows off the necessity of taking into account the viscous effects in a supersonic compressor flow calculation.

Numerical investigation of the axial compressor performance with inlet distortions

2017 ◽  
Vol 232 (8) ◽  
pp. 1434-1441
Author(s):  
ZX Liu ◽  
HZ Diao ◽  
XC Zhu ◽  
ZH Du
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Body Force ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Force Model ◽  
Transonic Compressor ◽  
High Pressure Ratio ◽  
Compressor Performance

In this paper, a three-dimensional body force model for predicting compressor performance and stability is implemented in the Ansys CFX. The influence of the blade rows on the flow field is represented by the source terms of CFX-solver equation. At first, a high-speed and high-pressure-ratio transonic compressor with the clean inlet is investigated. The overall performance and the flow fields are in agreement well with those of the experimental date, so the model is reliable and correct. Then, the effects of the circumferential distortions in the inlet total pressure and the total temperature on the compressor performance and flow field are also illustrated, respectively. In summary, the proposed body force model is suitable to investigate the flow field of the compressor with the inlet distortions.

Study of the Standard k-ε Model for Tip Leakage Flow in an Axial Compressor Rotor

2016 ◽  
Vol 33 (4) ◽  
Author(s):  
Yanfei Gao ◽  
Yangwei Liu ◽  
Luyang Zhong ◽  
Jiexuan Hou ◽  
Lipeng Lu
Keyword(s):  
Flow Field ◽  
Large Scale ◽  
Turbulent Viscosity ◽  
Axial Compressor ◽  
Leakage Flow ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Compressor Rotor

AbstractThe standard k-ε model (SKE) and the Reynolds stress model (RSM) are employed to predict the tip leakage flow (TLF) in a low-speed large-scale axial compressor rotor. Then, a new research method is adopted to “freeze” the turbulent kinetic energy and dissipation rate of the flow field derived from the RSM, and obtain the turbulent viscosity using the Boussinesq hypothesis. The Reynolds stresses and mean flow field computed on the basis of the frozen viscosity are compared with the results of the SKE and the RSM. The flow field in the tip region based on the frozen viscosity is more similar to the results of the RSM than those of the SKE, although certain differences can be observed. This finding indicates that the non-equilibrium turbulence transport nature plays an important role in predicting the TLF, as well as the turbulence anisotropy.

scholarly journals Incidence Angle and Pitch-Chord Effects on Secondary Flows Downstream of a Turbine Cascade

1992 ◽  
Author(s):  
A. Perdichizzi ◽  
V. Dossena
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Incidence Angle ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Turbine Cascade ◽  
Oil Flow ◽  
Secondary Velocity ◽  
Secondary Flow Field

This paper describes the results of an experimental investigation of the three-dimensional flow downstream of a linear turbine cascade at off-design conditions. The tests have been carried out for five incidence angles from −60 to +35 degrees, and for three pitch-chord ratios: s/c = 0.58,0.73,0.87. Data include blade pressure distributions, oil flow visualizations, and pressure probe measurements. The secondary flow field has been obtained by traversing a miniature five hole probe in a plane located at 50% of an axial chord downstream of the trailing edge. The distributions of local energy loss coefficients, together with vorticity and secondary velocity plots show in detail how much the secondary flow field is modified both by incidence and cascade solidity variations. The level of secondary vorticity and the intensity of the crossflow at the endwall have been found to be strictly related to the blade loading occurring in the blade entrance region. Heavy changes occur in the spanwise distributions of the pitch averaged loss and of the deviation angle, when incidence or pitch-chord ratio is varied.

Numerical Investigation of a Cantilevered Compressor Stator at Varying Clearance Sizes

2015 ◽  
Author(s):  
Chengwu Yang ◽  
Xingen Lu ◽  
Yanfeng Zhang ◽  
Shengfeng Zhao ◽  
Junqiang Zhu
Keyword(s):  
Flow Field ◽  
Axial Compressor ◽  
High Flow ◽  
Leakage Flow ◽  
Streamwise Direction ◽  
Stall Margin ◽  
Axial Compressors ◽  
Pressure Surface ◽  
The Impact ◽  
Highly Loaded

The clearance size of cantilevered stators affects the performance and stability of axial compressors significantly. Numerical calculations were carried out using the commercial software FINE/Turbo for a 2.5-stage highly loaded transonic axial compressor, which is of cantilevered stator for the first stage, at varying hub clearance sizes. The aim of this work is to improve understanding of the impact mechanism of hub clearance on the performance and the flow field in high flow turning conditions. The performance of the front stage and the compressor with different hub clearance sizes of the first stator has been analyzed firstly. Results show that the efficiency decreases as clearance size varies from 0 to 3% of hub chordlength, but the operating range has been extended. For the first stage, the efficiency decreases about 0.5% and the stall margin is extended. The following analysis of detailed flow field in the first stator shows that the clearance leakage flow and elimination of hub corner separation is responsible for the increasing loss and stall margin extending respectively. The effects of hub clearance on the downstream rotor have been discussed lastly. It indicates that the loss of the rotor increases and the flow deteriorates due to increasing of clearance size and hence the leakage mass flow rate, which mainly results from the interaction of upstream leakage flow with the passage flow near pressure surface. The affected region of rotor passage flow field expands in spanwise and streamwise direction as clearance size grows. The hub clearance leakage flow moves upward in span as it flows toward downstream.

Characteristics of Stable Rotating Stall Cells in an Axial Compressor

2017 ◽  
Author(s):  
Adam R. Hickman ◽  
Scott C. Morris
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Pressure Ratio ◽  
Pressure Sensors ◽  
Axial Compressor ◽  
Field Measurements ◽  
Rotating Stall ◽  
Flow Coefficient ◽  
Stable Operation ◽  
Double Phase

Flow field measurements of a high-speed axial compressor are presented during pre-stall and post-stall conditions. The paper provides an analysis of measurements from a circumferential array of unsteady shroud static pressure sensors during stall cell development. At low-speed, the stall cell approached a stable size in approximately two rotor revolutions. At higher speeds, the stall cell developed within a short amount of time after stall inception, but then fluctuated in circumferential extent as the compressor transiently approached a stable post-stall operating point. The size of the stall cell was found to be related to the annulus average flow coefficient. A discussion of Phase-Locked Average (PLA) statistics on flow field measurements during stable operation is also included. In conditions where rotating stall is present, flow field measurements can be Double Phase-Locked Averaged (DPLA) using a once-per-revolution (1/Rev) pulse and the period of the stall cell. The DPLA method provides greater detail and understanding into the structure of the stall cell. DPLA data indicated that a stalled compressor annulus can be considered to contained three main regions: over-pressurized passages, stalled passages, and recovering passages. Within the over-pressured region, rotor passages exhibited increased blade loading and pressure ratio compared to pre-stall values.

The Impact of Manufacturing Variations on Performance of a Transonic Axial Compressor Rotor

2018 ◽  
Author(s):  
Marcus Lejon ◽  
Niklas Andersson ◽  
Lars Ellbrant ◽  
Hans Mårtensson
Keyword(s):  
Flow Field ◽  
Geometric Mean ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Mean Deviation ◽  
Design Intent ◽  
Compressor Rotor ◽  
Measuring Machine ◽  
The Mean ◽  
The Impact

In this paper, the impact of manufacturing variations on performance of an axial compressor rotor are evaluated at design rotational speed. The geometric variations from the design intent were obtained from an optical coordinate measuring machine and used to evaluate the impact of manufacturing variations on performance and the flow field in the rotor. The complete blisk is simulated using 3D CFD calculations, allowing for a detailed analysis of the impact of geometric variations on the flow. It is shown that the mean shift of the geometry from the design intent is responsible for the majority of the change in performance in terms of mass flow and total pressure ratio for this specific blisk. In terms of polytropic efficiency, the measured geometric scatter is shown to have a higher influence than the geometric mean deviation. The geometric scatter around the mean is shown to impact the pressure distribution along the leading edge and the shock position. Furthermore, a blisk is analyzed with one blade deviating substantially from the design intent, denoted as blade 0. It is shown that the impact of blade 0 on the flow is largely limited to the blade passages that it is directly a part of. The results presented in this paper also show that the impact of this blade on the flow field can be represented by a simulation including 3 blade passages. In terms of loss, using 5 blade passages is shown to give a close estimate for the relative change in loss for blade 0 and neighboring blades.

Sign in / Sign up

Export Citation Format

Share Document