Prediction of Flow and Combustion Characteristics for a Gas Turbine Combustor Burning Low Heating Value Fuel

2010 ◽  
Author(s):  
M. R. Shaalan ◽  
H. A. El Salmawy ◽  
M. Anwar Ismail
Keyword(s):  
Gas Turbine ◽  
Performance Indicators ◽  
Substantial Reduction ◽  
Combustion Characteristics ◽  
Swirl Ratio ◽  
Operational Parameters ◽  
Gas Turbine Combustor ◽  
Heating Value ◽  
Secondary Air ◽  
The Impact

In this study, a numerical model has been developed to simulate the flow and combustion in a gas turbine combustor of type (Winnox-TUD-Combustor), which burns low heating value gas. The model relies on the computational code “FLUENT”. This code has been used to solve the governing equations. The characteristics of the model are; steady, turbulent, two dimensional, axisymmetric and swirling flow. The combustion process has been simulated as non-premixed combustion. The study includes the impact of several design and operational parameters on the characteristics of the flow and combustion inside the combustion chamber. These parameters include; ratio of secondary to primary air, ratio of tertiary to primary air, swirl ratio, number of inlets of the secondary air and their direction. Four performance indicators have been used to evaluate the impact of the aforementioned design and operating parameters. These indicators include; average temperature of the exhaust gases to the turbine, specific NOx emission, pattern factor and combustion efficiency of the combustor. In order to identify the optimum values of the aforementioned design and operational parameters, Artificial Neural Network (ANN) technique has been utilized to enrich the output results. This facilitates searching for the optimum values of the aforementioned parameters. Furthermore the effect of the variations in fuel composition on the combustion characteristics and accordingly on the performance indicators has been studied. It has been found that, all the studied parameters affect the performance of the combustor to a certain extent. However, fuel swirl ratio, primary to secondary air ratio and tertiary to primary air ratio as well as carbon monoxide to hydrogen ratio in the fuel are the controlling factors. Optimizing these parameters can lead to a substantial reduction in specific NOx emissions down to 4.0 gm/kg of fuel. Also an improvement in pattern factor to values below 0.3 has been achieved.

scholarly journals Comprehensive Thermodynamic Analysis of the Humphrey Cycle for Gas Turbines with Pressure Gain Combustion

Energies ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 3521 ◽  
Author(s):  
Panagiotis Stathopoulos
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Combustion Process ◽  
Ideal Gas ◽  
Point Of View ◽  
Pressure Gain Combustion ◽  
Combustion Technology ◽  
Secondary Air ◽  
And Performance ◽  
The Impact

Conventional gas turbines are approaching their efficiency limits and performance gains are becoming increasingly difficult to achieve. Pressure Gain Combustion (PGC) has emerged as a very promising technology in this respect, due to the higher thermal efficiency of the respective ideal gas turbine thermodynamic cycles. Up to date, only very simplified models of open cycle gas turbines with pressure gain combustion have been considered. However, the integration of a fundamentally different combustion technology will be inherently connected with additional losses. Entropy generation in the combustion process, combustor inlet pressure loss (a central issue for pressure gain combustors), and the impact of PGC on the secondary air system (especially blade cooling) are all very important parameters that have been neglected. The current work uses the Humphrey cycle in an attempt to address all these issues in order to provide gas turbine component designers with benchmark efficiency values for individual components of gas turbines with PGC. The analysis concludes with some recommendations for the best strategy to integrate turbine expanders with PGC combustors. This is done from a purely thermodynamic point of view, again with the goal to deliver design benchmark values for a more realistic interpretation of the cycle.

Gas Turbine Combined Cycle With CO2-Capture Using Auto-Thermal Reforming of Natural Gas

2000 ◽  
Author(s):  
Thormod Andersen ◽  
Hanne M. Kvamsdal ◽  
Olav Bolland
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Process Integration ◽  
Combined Cycle ◽  
Co2 Removal ◽  
Gas Turbine Combustor ◽  
Chemical Absorption ◽  
Fuel Gas ◽  
The Impact ◽  
Water Gas

A concept for capturing and sequestering CO2 from a natural gas fired combined cycle power plant is presented. The present approach is to decarbonise the fuel prior to combustion by reforming natural gas, producing a hydrogen-rich fuel. The reforming process consists of an air-blown pressurised auto-thermal reformer that produces a gas containing H2, CO and a small fraction of CH4 as combustible components. The gas is then led through a water gas shift reactor, where the equilibrium of CO and H2O is shifted towards CO2 and H2. The CO2 is then captured from the resulting gas by chemical absorption. The gas turbine of this system is then fed with a fuel gas containing approximately 50% H2. In order to achieve acceptable level of fuel-to-electricity conversion efficiency, this kind of process is attractive because of the possibility of process integration between the combined cycle and the reforming process. A comparison is made between a “standard” combined cycle and the current process with CO2-removal. This study also comprise an investigation of using a lower pressure level in the reforming section than in the gas turbine combustor and the impact of reduced steam/carbon ratio in the main reformer. The impact on gas turbine operation because of massive air bleed and the use of a hydrogen rich fuel is discussed.

Combustion Characteristics of Small Size Gas Turbine Combustor Fueled by Biomass Gas Employing Flameless Combustion

2007 ◽  
Author(s):  
Masato Hiramatsu ◽  
Yoshifumi Nakashima ◽  
Sadamasa Adachi ◽  
Yudai Yamasaki ◽  
Shigehiko Kaneko
Keyword(s):  
Gas Turbine ◽  
Combustion Efficiency ◽  
Combustion Characteristics ◽  
Operating Conditions ◽  
Nox Emissions ◽  
Gas Turbine Combustor ◽  
Flameless Combustion ◽  
Engine Exhaust ◽  
Micro Gas Turbine

One approach to achieving 99% combustion efficiency (C.E.) and 10 ppmV or lower NOx (at 15%O2) in a micro gas turbine (MGT) combustor fueled by biomass gas at a variety of operating conditions is with the use of flameless combustion (FLC). This paper compares experimentally obtained results and CHEMKIN analysis conducted for the developed combustor. As a result, increase the number of stage of FLC combustion enlarges the MGT operation range with low-NOx emissions and high-C.E. The composition of fuel has a small effect on the characteristics of ignition in FLC. In addition, NOx in the engine exhaust is reduced by higher levels of CO2 in the fuel.

Impact of Ethane, Propane, and Diluent Content in Natural Gas on the Performance of a Commercial Microturbine Generator

2008 ◽  
Vol 130 (1) ◽  
Author(s):  
Richard L. Hack ◽  
Vincent G. McDonell
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Gas Turbine ◽  
Fuel Composition ◽  
Nox Emissions ◽  
Heating Value ◽  
Designed Experiment ◽  
Methane Number ◽  
The Impact ◽  
Lean Conditions

The impact of fuel composition on the performance of power generation devices is gaining interest as the desire to diversify fuel supplies increases. In the present study, measurements of combustion performance were conducted on a commercial natural gas-fired 60kW gas turbine as a function of fuel composition. A statistically designed experiment was carried out and exhaust emissions were obtained for significant amounts of ethane and propane. In addition, a limited study of the effect of inerts was conducted. The results show that emissions of NOx, CO, and NOx∕NO are not well correlated with common descriptions of the fuel, such as higher heating value or methane number. The results and trends indicate that the presence of higher hydrocarbons in the fuel leads to appreciably higher NOx emissions for both test devices operating under similar lean conditions, while having less impact on CO emissions.

Experimental Investigation of the Performance of a Micro Gas Turbine Fueled With Mixtures of Natural Gas and Biogas

2013 ◽  
Author(s):  
Homam Nikpey ◽  
Mohsen Assadi ◽  
Peter Breuhaus
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Co2 Emissions ◽  
Fuel Mixture ◽  
Combined Heat And Power ◽  
Test Rig ◽  
Heating Value ◽  
Micro Gas Turbine ◽  
Fuel Mixtures ◽  
The Impact

Previously published studies have addressed modifications to the engines when operating with biogas, i.e. a low heating value (LHV) fuel. This study focuses on mapping out the possible biogas share in a fuel mixture of biogas and natural gas in micro combined heat and power (CHP) installations without any engine modifications. This contributes to a reduction in CO2 emissions from existing CHP installations and makes it possible to avoid a costly upgrade of biogas to the natural gas quality as well as engine modifications. Moreover, this approach allows the use of natural gas as a “fallback” solution in the case of eventual variations of the biogas composition and or shortage of biogas, providing improved availability. In this study, the performance of a commercial 100kW micro gas turbine (MGT) is experimentally evaluated when fed by varying mixtures of natural gas and biogas. The MGT is equipped with additional instrumentation, and a gas mixing station is used to supply the demanded fuel mixtures from zero biogas to maximum possible level by diluting natural gas with CO2. A typical biogas composition with 0.6 CH4 and 0.4 CO2 (in mole fraction) was used as reference, and corresponding biogas content in the supplied mixtures was computed. The performance changes due to increased biogas share were studied and compared with the purely natural gas fired engine. This paper presents the test rig setup used for the experimental activities and reports results, demonstrating the impact of burning a mixture of biogas and natural gas on the performance of the MGT. Comparing with when only natural gas was fired in the engine, the electrical efficiency was almost unchanged and no significant changes in operating parameters were observed. It was also shown that burning a mixture of natural gas and biogas contributes to a significant reduction in CO2 emissions from the plant.

Three-Dimensional CFD Analysis of a Gas Turbine Combustor for Medium/Low Heating Value Syngas Fuel

2008 ◽  
Author(s):  
Yan Xiong ◽  
Lucheng Ji ◽  
Zhedian Zhang ◽  
Yue Wang ◽  
Yunhan Xiao
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Coal Gasification ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Combined Cycle ◽  
Gas Turbine Combustor ◽  
Integrated Gasification Combined Cycle ◽  
Heating Value ◽  
Flamelet Model

Gas turbine is one of the key components for integrated gasification combined cycle (IGCC) system. Combustor of the gas turbine needs to burn medium/low heating value syngas produced by coal gasification. In order to save time and cost during the design and development of a gas turbine combustor for medium/low heating value syngas, computational fluid dynamics (CFD) offers a good mean. In this paper, 3D numerical simulations were carried out on a full scale multi-nozzle gas turbine combustor using commercial CFD software FLUENT. A 72 degrees sector was modeled to minimize the number of cells of the grid. For the fluid flow part, viscous Navier-Stokes equations were solved. The realizable k-ε turbulence model was adopted. Steady laminar flamelet model was used for the reacting system. The interaction between fluid turbulence and combustion chemistry was taken into account by the PDF (probability density function) model. The simulation was performed with two design schemes which are head cooling using film-cooling and impingement cooling. The details of the flow field and temperature distribution inside the two gas turbine combustors obtained could be cited as references for design and retrofit. Similarities were found between the predicted and experimental data of the transition duct exit temperature profile. There is much work yet to be done on modeling validation in the future.

Axial Compressor Degradation Effects on Heavy Duty Gas Turbines Overall Performances

2013 ◽  
Author(s):  
Pio Astrua ◽  
Stefano Cecchi ◽  
Stefano Piola ◽  
Andrea Silingardi ◽  
Federico Bonzani
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Axial Compressor ◽  
Performance Parameters ◽  
Heavy Duty ◽  
Compressor Blades ◽  
Modular Model ◽  
Secondary Air ◽  
The Impact ◽  
Insight Into

The operation of a gas turbine is the result of the aero-thermodynamic matching of several components which necessarily experience aging and degradation over time. An approach to treat degradation phenomena of the axial compressor is provided, with an insight into the impact they have on compressor operation and on overall GT performances. The analysis is focused on the surface fouling of compressor blades and on rotor tip clearances variation. A modular model is used to simulate the gas turbine operation in design and off-design conditions and the aerodynamic impact of fouling and rotor tip clearances increase is assessed by means of dedicated loss and deviation correlations implemented in the 1D mid-streamline code of the compressor modules. The two different degradation sources are individually considered and besides the overall GT performance parameters, the analysis includes an evaluation of the compressor degradation impact on the secondary air system.

Sign in / Sign up

Export Citation Format

Share Document