Numerical Investigation on Impact of a Flush-Mounted Airintake Exit Distortion to the Rear Fan Performance

2014 ◽  
Author(s):  
Lei Liu ◽  
Fu Chen ◽  
Huanlong Chen ◽  
Yanping Song
Keyword(s):  
Mass Flow ◽  
Total Pressure ◽  
Pressure Ratio ◽  
High Energy ◽  
Low Energy ◽  
Stable Operation ◽  
Inlet Distortion ◽  
Suction Control ◽  
Point Increase ◽  
Total Pressure Ratio

For the sake of investigating impact of inlet distortion on the fan stage performance, numerical simulation of the whole structure of a flush-mounted S-shaped inlet and the rear fan stage was conducted in this paper. The single fan stage with uniform air admission was researched at the same time for comparison. Considering substantial boundary layer ingesting, a scheme of suction control imposed at the first bend of the inlet was also carried out. The results show that the total pressure ratio as well as the efficiency of the fan stage decreases dramatically and the choked mass flow has a reduction about 1.20% as compare with the uniform air condition. With suction control, aerodynamic performance of the fan stage improves slightly, the choked mass flow and total pressure ratio at the maximum isentropic efficiency point increase about 0.28% and 0.25% respectively, and the stable operation range is extended. With effect of rotating rotor, the significant low energy region at bottom of the airintake exit decrease continually as it travels downstream to the rotor and covers nearly three flow passages at the front-edge rotor blade, moreover, the high-energy fluid mixes with the low-energy fluid.

Optimization of Highly Loaded Fan Rotor Based on Throughflow Model

2007 ◽  
Author(s):  
Hong Wu ◽  
Qiushi Li ◽  
Sheng Zhou
Keyword(s):  
Mass Flow ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Optimization Method ◽  
Design Variables ◽  
Adaptive Simulated Annealing ◽  
Throughflow Model ◽  
Important Design ◽  
Total Pressure Ratio ◽  
Highly Loaded

This paper presents an optimization method for fan/compressor which couples throughflow model solving axisymmetric Euler equations with adaptive simulated annealing (ASA) algorithm. One of the advantages of this optimization method is that it spends much less time than 3D optimization due to the rapid solving of throughflow model. In addition, the optimization space is quite extensive because more design variables can be adjusted in throughflow phase, such as swirl distribution, hub curve and sweep. To validate this optimization method, a highly loaded fan rotor with pressure ratio of 3.06 as a baseline is optimized. During the optimization process, the objective function is total pressure ratio, moreover, mass flow and efficiency are selected as the constraint conditions. Three important design variables including swirl distribution, hub curve and sweep are parameterized using Bezier curve, and then optimized in throughflow model independently, finally the optimum designs are validated using 3D viscous CFD solver. It is shown that pressure ratio and rotor loading can be improved further through optimizing swirl distribution, however, hub and sweep curves take more effects on mass flow and efficiency respectively. The optimization results demonstrate the advantage and feasibility of this optimization method.

Effect of inlet distortion on the performance of axial transonic contra-rotating compressor

2016 ◽  
Vol 232 (1) ◽  
pp. 42-54 ◽  
Author(s):  
Hanru Liu ◽  
Yangang Wang ◽  
Songchuan Xian ◽  
Wenbin Hu
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Tip Leakage Flow ◽  
Stall Margin ◽  
Tip Leakage ◽  
Inlet Distortion ◽  
Flow Mixing ◽  
Inflow Conditions ◽  
Total Pressure Ratio

The present paper numerically conducted full-annulus investigation on the effects of circumferential total pressure inlet distortion on the performance and flow field of the axial transonic counter-rotating compressor. Results reveal that the inlet distortion both deteriorates the performance of the upstream and downstream rotors resulting in reduction of total pressure ratio, efficiency and stall margin of the transonic contra-rotating compressor. Regarding the development of distortion inside compressor, the downstream rotor reinforces the air-flow mixing effects and, thus, attenuates the distortion intensity significantly. Under the distorted inflow conditions, the detached shockwave at the leading edge of downstream rotor interacts with the tip leakage flow and causes the blockage of the blades passage, which is one important reason for the transonic contra-rotating compressor stall.

Investigation of Effects of Radial Distortion on Transonic Fan Behavior

2010 ◽  
Author(s):  
Dmytro M. Voytovych ◽  
Guoping Xia ◽  
Chenzhou Lian ◽  
Charles L. Merkle
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Tip Vortex ◽  
Flow Rates ◽  
Mass Flow Rates ◽  
Transonic Fan ◽  
Total Pressure Ratio

The flow analysis around blades of a transonic fan is presented for both clean and radially distorted inlets. Computations are shown for four-blade passages that are accomplished with a second order accurate code using a k-ω turbulence model. The mass flow rate along a speed line is controlled by varying a choked nozzle downstream of the fan. The results show good agreement with data for three speed lines. In the near-stall region, the flow first becomes unsteady and then unstable with the unsteadiness increasing at lower speeds. The four-blade simulations remained stable to lower mass flow rates than the single-blade simulations. In the near-stall vicinity, tip vortex breakdown occurred creating a low momentum zone near the blade tip on the pressure side that grew as the mass flow was decreased until it eventually blocked the passage. The presence of distortion reduced the operational range and moved the stall line to higher mass flow rates. At high speeds distortion reduced both the mass flow rate and total pressure ratio while at lower speeds, the choking mass flow rate was reduced, but the total pressure ratio was slightly improved. The flow separation near the hub on the suction side was caused by the distortion. Its size was decreasing with rotational speed.

An Experimental Investigation About the Effect of the Partial Casing Treatment on a Transonic Axial-Flow Compressor Performance Under Inlet Distortion

2012 ◽  
Author(s):  
Maoyi Li ◽  
Wei Yuan ◽  
Xizhen Song ◽  
Yajun Lu ◽  
Zhiping Li ◽  
...  
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Peak Efficiency ◽  
Stall Margin ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Inlet Distortion ◽  
Flow Compressor ◽  
Total Pressure Ratio

The traditional annulus casing treatment often pays the price of lowered efficiency for improving the stall margin of a compressor under inlet distortion. In view of the unsymmetry of the inlet flow-field of compressors, partial casing treatment was used to control the flow in a transonic axial-flow compressor with arc-skewed-slots deployed at different circumferential positions under inlet distortion. The experimental results indicate that when the partial casing treatment is arranged on the undistorted and distorted sectors, the stall margin is enhanced by 8.02%, with the relative peak efficiency improved simultaneously by 2.143%, compared with the case of solid casing at 98% rotating speed. By contrast, the traditional casing treatment increases the stall-margin by 23.13%, but decreases the relative peak efficiency by 0.752%. By analyzing dynamic and static experimental data, the mechanism underlying the partial casing treatment was also studied in detail here. The disturbances of inlet flow were restrained by annulus casing treatment, nevertheless the total pressure ratio was decreased obviously in the distorted sector. As a result, the stall-margin is improved, but the relative peak efficiency is decreased too. When the partial casing treatment was arranged on the undistortded and distorted sectors, the stall disturbances was thereby restrained. So the stall margin was enhanced. In addition, the total pressure ratio was improved by the partial casing treatment in the distorted and transition sectors, and thus the relative peak efficiency was also increased markedly.

Effect of swirl on the performance and stability of transonic axial compressor

2017 ◽  
Vol 232 (6) ◽  
pp. 608-621
Author(s):  
Baofeng Tu ◽  
Luyao Zhang ◽  
Jun Hu
Keyword(s):  
Mass Flow ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Maximum Efficiency ◽  
Stable Boundary ◽  
Tip Leakage ◽  
Stable Operating ◽  
Swirl Intensity ◽  
Total Pressure Ratio

To investigate the effect of twin swirl and bulk swirl on the performance and stability of a transonic axial compressor, a blade swirl generator was designed and simulated with a transonic single rotor using steady and unsteady numerical calculation methods. The bulk swirl intensity was adjusted by replacing the blades with different camber angles. The twin swirl intensity was decreased by reducing the blade number. The counter-rotating bulk swirl generated a significant drop in both the efficiency and stall margin, and resulted in an increase in the choked mass flow, and total pressure ratio. The co-rotating bulk swirl generated a decrease in the mass flow, total pressure ratio and stable operating range. The counter-rotating bulk swirl resulted in suction surface boundary layer separation beyond 50% of the span-wise height as well as more serious tip leakage blockage. The twin swirl resulted in a decrease in the total pressure ratio, maximum efficiency and stable operating range. The steady and unsteady numerical calculation results were consistent, though some differences were observed in the values. For the steady calculation, the maximum efficiency and choked mass flow decreased by 0.88% and 1.74%, respectively, and the mass flow at the stable boundary increased by 3.92% as compared to the uniform inlet flow at twin swirl intensity of 24°. During the unsteady calculation, the mass flow exhibited an increase of only 2.2% at the stable boundary. Under twin swirl and co-rotating bulk swirl and uniform inlet flow, the leading edge spillage of the tip leakage flow resulted in compressor instability. The counter-rotating bulk swirl changed the mechanism of instability. The characterisation of the swirl distortion presented a difference between the steady and unsteady calculations near the stable boundary. The unsteady calculation exhibited a lower mass flow at the stable boundary point and a higher total pressure ratio.

Time Resolved Simulation and Experimental Validation of the Flow in Axial Slot Casing Treatments for Transonic Axial Compressors

2008 ◽  
Author(s):  
Giovanni A. Brignole ◽  
Florian C. T. Danner ◽  
Hans-Peter Kau
Keyword(s):  
Mass Flow ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Compressor Stage ◽  
Time Resolved ◽  
Transonic Compressor ◽  
Design Speed ◽  
Casing Treatments ◽  
Total Pressure Ratio

Building on the experience of previous investigations, a casing treatment was developed and applied to an axial transonic compressor stage, in literature referred to as Darmstadt Rotor 1. The aerodynamics of the experimental compressor stage was improved by applying axially orientated semicircular slots to the original plain casing, which both enhanced the operating range and design point efficiency. A gain in total pressure ratio along the entire design speed line was also observed. Within the scope of this study four different axial casing treatments were designed. Their effect on the flow in a transonic axial compressor stage was investigated parametrically using time-resolved 3D-FANS simulations with a mesh of approximately 4.8 · 106 grid points. This research aims to identify correlations between the geometrical cavity design and the changed channel flow. The findings help to formulate parameters for evaluating the performance of casing treatments. These criteria can further be used as target functions in the design optimisation process. The predicted behaviour of the transonic compressor was validated against experiments as well as an alternative numerical model, the non-linear harmonic method. Both confirmed the effect of the slots in raising efficiency as well as moving the design speed line towards higher pressure ratios. In the experiments, the addition of the slots increased the total pressure ratio at stall conditions by more than 5% and reduced mass flow from 87.5% of the design mass flow to less than 77.5% compared to the original geometry.

Investigation Into the Effects of Hub Rotation on the Hub Leakage Flow of Cantilever Stator in a Transonic Axial Compressor

2020 ◽  
Author(s):  
Botao Zhang ◽  
Bo Liu ◽  
Xin Sun ◽  
Hang Zhao
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Blade Root ◽  
Flow Loss ◽  
Total Pressure Ratio

Abstract In order to explore the similarities and differences between the flow fields of cantilever stator and idealized compressor cascade with tip clearance, and to extend the cascade leakage model to compressors, the influence of stator hub rotation to represent cascade and cantilever stator on hub leakage flow was numerically studied. On this basis, the control strategy and mechanism of blade root suction were discussed. The results show that there is no obvious influence on stall margin of the compressor whether the stator hub is rotating or stationary. For rotating stator hub, the overall efficiency is decreased while the total pressure ratio is increased. At peak efficiency point and near stall point, the efficiency is reduced by about 0.43% and 0.34% individually, while the total pressure ratio is enlarged by about 0.23% and 0.27%, respectively. The gap leakage flow is promoted due to stator hub rotation, and the structure of the leakage vortex is weakened obviously. In addition, the hub leakage flow originating from the blade leading edge of rotating hub may contribute to double leakage near the trailing edge of the adjacent blade. However, the leakage flow directly out of the blade passage with stationary stator hub. The stator root loading and strength of the leakage flow increase with the rotation of the hub, and the leakage vortex is further away from the suction surface of the blade and is stretched to an ellipse closer to the endwall under the shear action. The rotating hub makes the flow loss near the stator gap increase, while the flow loss in the upper part of the blade root is decreased. Meanwhile, the total pressure ratio in the end area is increased. Blade root suction of cantilever stator can effectively control the hub leakage flow, inhibit the development of hub leakage vortex, and improve the flow capacity of the passage, thereby reducing the flow loss and modifying the flow field in the end zone.

Research on Optimization of the Design(Inverse) Issue of S2 Surface of Axial Compressor Based on Genetic Algorithm

2020 ◽  
Author(s):  
Zijing Chen ◽  
Bo Liu ◽  
Xiaoxiong Wu
Keyword(s):  
Genetic Algorithm ◽  
Total Pressure ◽  
Fitness Function ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Local Data ◽  
Real Coded Genetic Algorithm ◽  
Overall Efficiency ◽  
Total Pressure Ratio ◽  
Peak Value

Abstract In order to further improve the effectiveness of design(inverse) issue of S2 surface of axial compressor, a design method of optimization model based on real-coded genetic algorithm is instructed, with a detailed description of some important points such as the population setting, the fitness function design and the implementation of genetic operator. The method mainly takes the pressure ratio, the circulation as the optimization variables, the total pressure ratio and the overall efficiency of the compressor as the constraint condition and the decreasing of the diffusion factor of the compressor as the optimization target. In addition, for the propose of controlling the peak value of some local data after the optimization, a local optimization strategy is proposed to make the method achieve better results. In the optimization, the streamline curvature method is used to perform the iterative calculation of the aerodynamic parameters of the S2 flow surface, and the polynomial fitting method is used to optimize the dimensionality of the variables. The optimization result of a type of ten-stage axial compressor shows that the pressure ratio and circulation parameters have significant effect on the diffusion factor’s distribution, especially for the rotor pressure ratio. Through the optimization, the smoothness of the mass-average pressure ratio distribution curve of the rotors at all stages of the compressor is improved. The maximum diffusion factors in spanwise of rotor rows at the first, fifth and tenth stage of the compressor are reduced by 1.46%, 12.53% and 8.67%, respectively. Excluding the two calculation points at the root and tip of the blade because of the peak value, the average diffusion factors in spanwise are reduced by 1.28%, 3.46%, and 1.50%, respectively. For the two main constraints, the changes of the total pressure ratio and overall efficiency are less than 0.03% and 0.032%, respectively. In the end, a 3-d CFD numerical result is given to testify the effects of the optimization, which shows that the loss in the compressor is decreased by the optimization algorithm.

Numerical Investigation on the Effects of Circumferential Coverage of Injection in a Transonic Compressor With Discrete Tip Injection

2014 ◽  
Author(s):  
Wei Wang ◽  
Wuli Chu ◽  
Haoguang Zhang ◽  
Yanhui Wu
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Time Lag ◽  
Three Dimensional ◽  
Stability Margin ◽  
Transonic Compressor ◽  
Blade Tip ◽  
Tip Injection ◽  
The Stability ◽  
Total Pressure Ratio

Discrete tip injection upstream of the rotor tip is an effective technique to extend stability margin for a compressor system in an aeroengine. The current study investigates the effects of injectors’ circumferential coverage on compressor performance and stability using time-accurate three-dimensional numerical simulations for multi passages in a transonic compressor. The percentage of circumferential coverage for all the six injectors ranges from 6% to 87% for the five investigated configurations. Results indicate that circumferential coverage of tip injection can greatly affect compressor stability and total pressure ratio, but has little influence on adiabatic efficiency. The improvement of compressor total pressure ratio is linearly related with the increasing circumferential coverage. The unsteady flow fields show that there exists a non-ignorable time lag of the injection effects between the passage inlet and outlet, and blade tip loading will not decline until the injected flow reaches the passage outlet. Stability improves sharply with the increasing circumferential coverage when the coverage is less than 27%, but increases flatly for the rest. It is proven that the injection efficiency which is a measurement of averaged blockage decrement in the injected region is an effective guideline to predict the stability improvement.

Experimental Investigation of Aspiration in a Multi-Stage High-Speed Axial-Compressor

2016 ◽  
Author(s):  
Jan Siemann ◽  
Ingolf Krenz ◽  
Joerg R. Seume
Keyword(s):  
Flow Field ◽  
Total Pressure ◽  
High Speed ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Reference Configuration ◽  
Corner Separation ◽  
Part Load ◽  
Total Pressure Ratio ◽  
Isentropic Efficiency

Reducing the fuel consumption is a main objective in the development of modern aircraft engines. Focusing on aircraft for mid-range flight distances, a significant potential to increase the engines overall efficiency at off-design conditions exists in reducing secondary flow losses of the compressor. For this purpose, Active Flow Control (AFC) by aspiration or injection of fluid at near wall regions is a promising approach. To experimentally investigate the aerodynamic benefits of AFC by aspiration, a 4½-stage high-speed axial-compressor at the Leibniz Universitaet Hannover was equipped with one AFC stator row. The numerical design of the AFC-stator showed significant hub corner separations in the first and second stator for the reference configuration at the 80% part-load speed-line near stall. Through the application of aspiration at the first stator, the numerical simulations predict the complete suppression of the corner separation not only in the first, but also in the second stator. This leads to a relative increase in overall isentropic efficiency of 1.47% and in overall total pressure ratio of 4.16% compared to the reference configuration. To put aspiration into practice, the high-speed axial-compressor was then equipped with a secondary air system and the AFC stator row in the first stage. All experiments with AFC were performed for a relative aspiration mass flow of less than 0.5% of the main flow. Besides the part-load speed-lines of 55% and 80%, the flow field downstream of each blade row was measured at the AFC design point. Experimental results are in good agreement with the numerical predictions. The use of AFC leads to an increase in operating range at the 55% part-load speed-line of at least 19%, whereas at the 80% part-load speed-line no extension of operating range occurs. Both speed-lines, however, do show a gain in total pressure ratio and isentropic efficiency for the AFC configuration compared to the reference configuration. Compared to the AFC design point, the isentropic efficiency ηis rises by 1.45%, whereas the total pressure ratio Πtot increases by 1.47%. The analysis of local flow field data shows that the hub corner separation in the first stator is reduced by aspiration, whereas in the second stator the hub corner separation slightly increases. The application of AFC in the first stage further changes the stage loading in all downstream stages. While the first and third stage become unloaded by application of AFC, the loading in terms of the De-Haller number increases in the second and especially in the fourth stage. Furthermore, in the reference as well as in the AFC configuration, the fourth stator performs significantly better than predicted by numerical results.

Sign in / Sign up

Export Citation Format

Share Document