A Comparative Study of Combustion Models for Spark Ignition Engines Based on Experimentation and CFD Simulation

2010 ◽  
Author(s):  
Raouf Mobasheri ◽  
M. Sadegh Shahrokhi-Dehkordi
Keyword(s):  
Comparative Study ◽  
Cfd Simulation ◽  
Combustion Process ◽  
Experimental Tests ◽  
Experimental Results ◽  
Nox Emission ◽  
Combustion Model ◽  
Spark Ignition Engines ◽  
Flamelet Model ◽  
Combustion Models

Computational fluid dynamics (CFD) is able to significantly reduce the number of experimental tests and measurements and lower the development time and costs. However some parameters which are needed for CFD calculation must be achieved experimentally. In this paper, a comparative study was carried out to clarify the effect of three different combustion models on the prediction capability of combustion process and NOx emission on a modified 4-cylinder MPFI SI engine. Validation of the combustion model has been performed through comparing simulation data with the experimental results and a satisfactory agreement between them has been achieved in terms of combustion parameters and NOx emission. The results show that, applying appropriate constants of each combustion model including Eddy break up model (Ebu), Probability density function (Pdf) and Coherent flamelet model (Cfm) causes the computational results to be in agreement with experimental results. Furthermore the results show that the nearest prediction in comparison with experimental results is by applying the Ebu model.

scholarly journals Numerical Study of Engine Performance and Emissions for Port Injection of Ammonia into a Gasoline\Ethanol Dual-Fuel Spark Ignition Engine

2021 ◽  
Vol 11 (4) ◽  
pp. 1441
Author(s):  
Farhad Salek ◽  
Meisam Babaie ◽  
Amin Shakeri ◽  
Seyed Vahid Hosseini ◽  
Timothy Bodisco ◽  
...  
Keyword(s):  
Numerical Study ◽  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Model ◽  
Dual Fuel ◽  
Spark Ignition Engines ◽  
Performance And Emissions ◽  
Hc Emissions

This study aims to investigate the effect of the port injection of ammonia on performance, knock and NOx emission across a range of engine speeds in a gasoline/ethanol dual-fuel engine. An experimentally validated numerical model of a naturally aspirated spark-ignition (SI) engine was developed in AVL BOOST for the purpose of this investigation. The vibe two zone combustion model, which is widely used for the mathematical modeling of spark-ignition engines is employed for the numerical analysis of the combustion process. A significant reduction of ~50% in NOx emissions was observed across the engine speed range. However, the port injection of ammonia imposed some negative impacts on engine equivalent BSFC, CO and HC emissions, increasing these parameters by 3%, 30% and 21%, respectively, at the 10% ammonia injection ratio. Additionally, the minimum octane number of primary fuel required to prevent knock was reduced by up to 3.6% by adding ammonia between 5 and 10%. All in all, the injection of ammonia inside a bio-fueled engine could make it robust and produce less NOx, while having some undesirable effects on BSFC, CO and HC emissions.

A Study of the NOx Emission in a Regenerative Industrial Furnace

2001 ◽  
Author(s):  
Qing Jiang ◽  
Chao Zhang
Keyword(s):  
Mixture Fraction ◽  
Combustion Process ◽  
Nox Emission ◽  
Moment Closure ◽  
Combustion Model ◽  
Industrial Furnace ◽  
Low Emission ◽  
Reduction Of Nox ◽  
Closure Method ◽  
Probability Density Function Pdf

Abstract A study of the nitrogen oxides (NOx) emission and combustion process in a gas-fired regenerative, high temperature, low emission industrial furnace has been carried out numerically. The effect of two additives, methanol (CH3OH) and hydrogen peroxide (H2O2), to fuel on the NOx emission has been studied. A moment closure method with the assumed β probability density function (PDF) for mixture fraction is used in the present work to model the turbulent non-premixed combustion process in the furnace. The combustion model is based on the assumption of instantaneous full chemical equilibrium. The results showed that CH3OH is effective in the reduction of NOx in a regenerative industrial furnace. However, H2O2 has no significant effect on the NOx emission.

A Control-Oriented Reaction-Based SI Engine Combustion Model

2018 ◽  
Author(s):  
Ruixue C. Li ◽  
Guoming G. Zhu
Keyword(s):  
Chemical Reaction ◽  
Mass Fraction ◽  
Combustion Process ◽  
Combustion Model ◽  
Spark Ignition Engines ◽  
Si Engine ◽  
Chemical Reaction Mechanism ◽  
Engine Combustion ◽  
Rate Of Heat Release ◽  
Mass And Heat Transfer

This paper proposes a control-oriented chemical reaction-based two-zone combustion model designed to accurately describe the combustion process and thermal performance for spark-ignition engines. The combustion chamber is assumed to be divided into two zones: reaction and unburned zones, where the chemical reaction takes place in the reaction zone and the unburned zone contains all the unburned mixture. In contrast to the empirical pre-determined Wiebe-function-based combustion model, an ideal two-step chemical reaction mechanism is used to reliably model the detailed combustion process such as mass-fraction-burned (MFB) and rate of heat release. The interaction between two zones includes mass and heat transfer at the zone interface to have a smooth combustion process. This control-oriented model is extensively calibrated based on the experimental data to demonstrate its capability of predicting the combustion process and thermodynamic states of the in-cylinder mixture.

COMPUTATIONAL STUDY ON COMBUSTION AND EMISSION CHARACTERISTIC OF PILOTED FLAMES BY VARYING COMPOSITION CO2 OF SIMULATED BIOGAS

2017 ◽  
Vol 79 (7-3) ◽  
Author(s):  
Khor Chin Keat ◽  
M. F. Mohd Yasin ◽  
M. A. Wahid ◽  
A. Saat ◽  
A. S. Md Yudin
Keyword(s):  
Computational Study ◽  
Flame Temperature ◽  
Dilution Effect ◽  
Co2 Concentration ◽  
Nox Emission ◽  
Combustion Model ◽  
Emission Characteristic ◽  
Measured Temperature ◽  
Flamelet Model ◽  
Detailed Chemistry

This study investigates the performance of flamelet model technique in predicting the behavior of piloted flame.A non-premixed methane flame of a piloted burner is simulated in OpenFOAM. A detailed chemistry of methane oxidation is integrated with the flamelet combustion model using probability density function (pdf) approach. The turbulence modelling adopts Reynolds Average Navier Stokes (RANS) framework with standard k-ε model. A comparison with experimental data demonstrates good agreement between the predicted and the measured temperature profiles in axial and radial directions. Recently, one of major concern with combustion system is the emission of pollution specially NOx emission. Reduction of the pollutions can be achieved by varying the composition of CO2 in biogas. In addition, the effect of the composition of biogas on NOx emission of piloted burner is still not understood. Therefore, understanding the behavior composition of CO2 in biogas is important that could affect the emission of pollution. In the present study, the use of biogas with composition of 10 to 30 percent of CO2 is simulated to study the effects of biogas composition on NOx emission. The comparison between biogas and pure methane are done based on the distribution of NOx, CO2, CH4, and temperature at different height above the burner. At varying composition of CO2 in biogas, the NOx emission for biogas with 30 percent CO2 is greatly reduced compared to that of 10 percent CO2. This is due to the reduction of the post flame temperature that is produced by the dilution effect at high CO2 concentration.  

Application of Various Combustion Models to a Generic Combustor

2003 ◽  
Author(s):  
Lei-Yong Jiang ◽  
Ian Campbell
Keyword(s):  
Experimental Tests ◽  
Combustion Model ◽  
Discrete Ordinates ◽  
Experimental Measurements ◽  
Finite Rate ◽  
Zone Length ◽  
Combustion Models ◽  
The Mean ◽  
Heat Transfers ◽  
Good Agreement

The flow-field of a generic gas combustor with interior and exterior conjugate heat transfers was numerically studied. Results obtained from three combustion models, combined with the re-normalization group (RNG) k-ε turbulence model, discrete ordinates radiation model, and partial equilibrium NOx model are presented and discussed. The numerical results are compared with a comprehensive database obtained from a series of experimental tests. The flow patterns and the recirculation zone length are excellently predicted, and the mean axial velocities are in fairly good agreement with the experimental measurements, particularly at downstream sections for all three combustion models. The mean temperature profiles are also fairly well captured by the probability density function (PDF) and eddy dissipation (EDS) combustion models. The EDS-finite-rate combustion model fails to provide acceptable temperature field. In general, the PDF shows some superiority over the EDS and EDS-finite-rate models. NOx levels predicted by the EDS model are in reasonable agreement with the experimental measurements.

Development and Validation of an Ignition Model for SI Engines

2006 ◽  
Author(s):  
Stefania Falfari ◽  
Gian Marco Bianchi
Keyword(s):  
Cfd Simulation ◽  
Combustion Process ◽  
Three Dimensional ◽  
Electrical Energy ◽  
Combustion Model ◽  
Test Case ◽  
Ignition Process ◽  
Mean Flow ◽  
Flame Kernel ◽  
Si Engines

In SI engines the ignition process strongly affects the combustion process. Its accurate modelling becomes a key issue for a design-oriented CFD simulation of the combustion process. Different approaches to simulate ignition have been proposed. The common base is decoupling the physics related to the very first ignition phase when a plasma is formed from that of the development of the flame kernel. The critical point of ignition models is related to the capability of representing the effect of ignition system characteristics, the criterion used for flame deposit and the initialisation of the combustion model. This paper aims to present and validates extensively an ignition model suited for CFD calculation of premixed combustion. The ignition model implemented in a customized version of the Kiva 3 code is coupled with ECFM Flamelet combustion model. The ignition model simulates the plasma/kernel expansion based on a lump evaluation of main ignition processes (i.e., breakdown, arc-phase and glow phase). A double switch criterion based on physical and numerical consideration is used to switch to the main combustion model. The Herweg and Maly experimental test case has been used to check the model capability. In particular, two different ignition systems having different amount of electrical energy released during spark discharge are considered. Comparisons with experimental results allowed testing the model with respect to its capability to reproduce the effects of mixture equivalence ratio, mean flow, turbulence and spark energy on flame kernel development as never done before in three-dimensional RANS CFD combustion modelling of premixed flames.

Combustion Development Investigation in a Common Rail Multi-Jet Diesel Engine With Up to 4 Injections per Engine Cycle

2005 ◽  
Author(s):  
Fabrizio Ponti ◽  
Gabriele Serra ◽  
Carlo Siviero
Keyword(s):  
Degrees Of Freedom ◽  
Combustion Process ◽  
Experimental Tests ◽  
Point Of View ◽  
Injection System ◽  
Combustion Model ◽  
Jet Engines ◽  
Injection Parameters ◽  
Start Of Injection ◽  
Engine Cycle

Newly developed technologies for modern diesel engines allow designing injection patterns with many degrees of freedom. Multi-jet engines, for example, can perform up to 5 injections within the same engine cycle: Position and duration of each injection, together with rail pressure and EGR rate can be chosen in order to properly design the desired in-cylinder combustion process. This means that during the injection system setup process all the free parameters have to be set to the desired value. If all the injection parameters variations have to be investigated in order to properly set their values, a huge amount of experimental tests should be needed. From this point of view, in order to reduce the need for test bench experimental work, the development of a combustion model can be very useful, to help determining the best injection configuration, and therefore the desired combustion into the cylinder. Single zone combustion models seem to be suitable for this task, thanks to the quick response they can give, and the possibility of using them for control purposes. In the paper a model developed for injection patterns with up to 4 injections is used in order to describe the combustion behavior as a function of the injection parameters. A properly designed set of tests has been performed in order to identify the combustion model. The obtained results give information on the way the combustion parameters, for example the combustion delays (i.e. the time delays between each Start Of Injection SOI, and the corresponding Start Of Combustion SOC), or the amount of fuel burnt for each injection are modified as the combustion process proceeds into the cylinder or as the injection parameters change. The information obtained can be in the following used in order to design the desired injection pattern, using the identified model as a virtual experimental tests generator.

A Study on Biodiesel NOx Emission Control With the Reduced Chemical Kinetics Model

2014 ◽  
Vol 136 (10) ◽  
Author(s):  
Juncheng Li ◽  
Zhiyu Han ◽  
Cai Shen ◽  
Chia-fon Lee
Keyword(s):  
Chemical Kinetics ◽  
Combustion Process ◽  
Operating Conditions ◽  
Nox Emission ◽  
Kinetics Model ◽  
Combustion Model ◽  
Nox Emissions ◽  
Soot Emission ◽  
Start Of Injection ◽  
Combustion Processes

In this paper, the effects of the start of injection (SOI) timing and exhaust gas recirculation (EGR) rate on the nitrogen oxides (NOx) emissions of a biodiesel-powered diesel engine are studied with computational fluid dynamics (CFD) coupling with a chemical kinetics model. The KIVA code coupling with a CHEMKIN-II chemistry solver is applied to the simulation of the in-cylinder combustion process. A surrogate biodiesel mechanism consisting of two fuel components is employed as the combustion model of soybean biodiesel. The in-cylinder combustion processes of the cases with four injection timings and three EGR rates are simulated. The simulation results show that the calculated NOx emissions of the cases with default EGR rate are reduced by 20.3% and 32.9% when the injection timings are delayed by 2- and 4-deg crank angle, respectively. The calculated NOx emissions of the cases with 24.0% and 28.0% EGR are reduced by 38.4% and 62.8%, respectively, compared to that of the case with default SOI and 19.2% EGR. But higher EGR rate deteriorates the soot emission. When EGR rate is 28.0% and SOI is advanced by 2 deg, the NOx emission is reduced by 55.1% and soot emission is controlled as that of the case with 24% EGR and default SOI. The NOx emissions of biodiesel combustion can be effectively improved by SOI retardation or increasing EGR rate. Under the studied engine operating conditions, introducing more 4.8% EGR into the intake air with unchanged SOI is more effective for NOx emission controlling than that of 4-deg SOI retardation with default EGR rate.

Development of a Common Rail Diesel Engine Combustion Model for ROHR Real-Time Estimation

2011 ◽  
Author(s):  
Fabrizio Ponti ◽  
Vittorio Ravaglioli ◽  
Matteo De Cesare
Keyword(s):  
Diesel Engine ◽  
Real Time ◽  
Combustion Process ◽  
Time Estimation ◽  
Experimental Tests ◽  
Common Rail ◽  
Combustion Model ◽  
Combustion Control ◽  
Injection Parameters ◽  
Real Time Estimation

Combustion control is a crucial aspect in modern Diesel engines control strategies, mainly due to the requests to increase efficiency and maintain pollutant emissions within the values bounded by standard regulations. In order to perform an accurate combustion control, modern “closed loop” control algorithms require the evaluation of a large number of quantities that provide information about combustion process effectiveness. This work presents a methodology that allows real-time estimation of energy released, during the combustion process, in a Common Rail Multi-Jet Diesel engine. This procedure can be divided in two main steps. The first step consists in the development of a zero-dimensional combustion model based on the linear combination of a proper number of Wiebe functions. In this case, a zero-dimensional approach has been chosen, because it is accurate enough for this analysis and requires low computational efforts. Once the combustion model has been developed, it can be used to determine Rate of Heat Release (RoHR) and the angular position in which 50% of fuel burned within an engine cycle is reached (MFB50). The second section of this work describes the relationships existing between injection parameters (such as Start of Injection, injected fuel quantities, rail pressure...) and the Wiebe parameters identified in the first step of the procedure. The above mentioned relationships have been used to set up correlations that allow estimating Wiebe parameters, therefore ROHR and MFB50, starting from injection parameters. The results obtained in MFB50 estimation are particularly emphasized, because real-time knowledge of this quantity is necessary to feedback a control algorithm for optimal combustion positioning. This work is based on several experimental tests performed on a 2.2 liters Common Rail Multi-Jet Diesel engine. First, experimental tests have been carried out to identify the combustion model and the correlations existing between Wiebe parameters and injection parameters. Then, in order to determine the accuracy of the approach, the complete estimation methodology has been applied to the engine under study. This work describes a methodology for real-time estimation of several quantities that provide important information about combustion process effectiveness (useful, for example, in modern low temperature combustion control systems). No extra cost is needed, because the methodology requires no additional sensor.

Impact of Flame Stretch and Heat Loss on Heat Release Distributions in Gas Turbine Combustors: Model Comparison and Validation

2016 ◽  
Author(s):  
Noah Klarmann ◽  
Thomas Sattelmayer ◽  
Weiqun Geng ◽  
Benjamin Timo Zoller ◽  
Fulvio Magni
Keyword(s):  
Experimental Data ◽  
Heat Loss ◽  
Model Comparison ◽  
Turbulent Flame ◽  
Combustion Process ◽  
Combustion Model ◽  
Qualitative Comparison ◽  
Combustion Models ◽  
Flamelet Generated Manifold ◽  
Flame Stretch

The work presented in this paper comprises the application of an extension for the Flamelet Generated Manifold model which allows to consider elevated flame stretch rates and heat loss. This approach does not require further table dimensions. Hence, the numerical overhead is negligible, preserving the industrial applicability. A validation is performed in which stretch and heat loss dependent distributions are obtained from the combustion model to compare them to experimental data from an atmospheric single burner test rig operating at lean conditions. The reaction mechanism is extended by OH*-kinetics which allows the comparison of numerical OH*-concentrations with experimentally obtained OH*-chemiluminescence. Improvement compared to the Flamelet Generated Manifold model without extension regarding the shape and position of the turbulent flame brush can be shown and are substantiated by the validation of species distributions which better fit the experimental in situ measurements when the extension is used. These improvements are mandatory to enable subsequent modeling of emissions or thermoacoustics where high accuracy is required. In addition to the validation, a qualitative comparison of further combustion models is performed in which the experimental data serve as a benchmark to evaluate the accuracy. Most combustion models typically simplify the combustion process as flame stretch or non-adiabatic effects are not captured. It turns out that the tested combustion models show improvement when stretch or heat loss is considered by model corrections. However, satisfactory results could only be achieved by considering both effects employing the extension for the Flamelet Generated Manifold model.

Sign in / Sign up

Export Citation Format

Share Document