Experimental Investigations on Combustion, Performance and Emission Characteristics of Neat Jatropha Biodiesel and its Methanol Blend in a Diesel Engine

2012 ◽  
Author(s):  
J. Thangaraja ◽  
K. Anand ◽  
Pramod S. Mehta
Keyword(s):  
Methyl Ester ◽  
Engine Performance ◽  
Experimental Results ◽  
Experimental Investigations ◽  
Injection Timing ◽  
Nox Emissions ◽  
Engine Exhaust ◽  
Performance And Emission ◽  
Full Load Operation ◽  
Unburned Hydrocarbons

While engines fueled with neat or blended biodiesel have favorable combustion-emission profile in terms of carbon monoxide, particulate matter and unburned hydrocarbons emissions, they are reported to have higher NOx emissions as compared to petro-diesel. On the other hand, use of alcohols especially methanol, though limited in diesel engines, is found to decrease engine exhaust emissions including smoke and NOx emissions. The present experimental investigation evaluates the use of biodiesel-methanol blend in mitigating higher NOx emissions in biodiesel fuelled engines along with its effect on other engine performance conditions. The experimental results obtained for a blend of 90% Jatropha methyl ester and 10% methanol (J90M10) and neat Jatropha methyl ester (J100) by varying engine output load at maximum torque speed of 1400 rpm are analyzed and discussed in this paper. The experimental results at full load operation for J90M10 blend compared with neat J100 indicate a reduction in exhaust nitric oxide and smoke concentrations by 28% and 50% respectively along with a reduction of 2% in peak pressure and 0.5% in brake thermal efficiency. Also, a marginal retard in injection timing and a higher ignition delay period is observed with Jatropha methyl ester -methanol blend operation.

Experimental Investigations on a Jatropha Oil Methyl Ester Fuelled Diesel Engine

2005 ◽  
Author(s):  
J. G. Suryawanshi ◽  
N. V. Deshpande
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Engine Performance ◽  
Diesel Oil ◽  
Experimental Investigations ◽  
Jatropha Oil ◽  
Engine Exhaust ◽  
Performance And Emission ◽  
Unburned Hydrocarbon ◽  
Hydrocarbon Emission

Biodiesel is a non-toxic, biodegradable and renewable fuel with the potential to reduce engine exhaust emissions. The methyl ester of jatropha oil, known as biodiesel, is receiving increasing attention as an alternative fuel for diesel engines. The biodiesel is obtained through transesterification process. Various properties of the biodiesel thus developed are evaluated and compared in relation to that of conventional diesel oil. In the present investigation neat jatropha oil methyl ester (JME) as well as the blends of varying proportions of jatropha oil methyl ester (JME) and diesel were used to run a CI engine. A four stroke diesel engine having compression ratio of 17.5: 1 and developing 5.2 kW at 1500 rpm was used. Experiments were initially carried out on the engine at all loads using diesel to provide baseline data. Significant improvements in engine performance and emission characteristics were observed for JME fuel. The addition of jatropha methyl ester (JME) to diesel fuel has significantly reduced HC, CO, CO2 and smoke emissions but it increases the NOx emission slightly. The maximum reduction in smoke emission was observed by 35% in case of neat biodiesel operation as compared to diesel. The unburned hydrocarbon emission was drastically reduced by 53% for neat biodiesel operation.

Emissions and Performance on a Jatropha Oil Methyl Ester Fueled Diesel Engine With Retarded Injection Timing

2013 ◽  
Author(s):  
J. G. Suryawanshi
Keyword(s):  
Methyl Ester ◽  
Diesel Engines ◽  
Direct Injection ◽  
Engine Performance ◽  
Nox Emission ◽  
Injection Timing ◽  
Nox Emissions ◽  
Jatropha Oil ◽  
Gas Temperature ◽  
Performance And Emission

Injection timing variations have a strong effect on NOx emissions for direct injection diesel engines. Retarded injection is commonly used to control NOx emissions. Biodiesel is a non-toxic, biodegradable and renewable fuel with the potential to reduce engine exhaust emissions. The methyl ester of jatropha oil, known as biodiesel, is receiving increasing attention as an alternative fuel for diesel engines. In the present investigation neat jatropha oil methyl ester (JME) as well as the blends of varying proportions of jatropha oil methyl ester (JME) and diesel were used to run a CI engine with standard injection timing and retarded injection timing. Significant improvements in engine performance and emission characteristics were observed for JME fuel. The addition of JME to diesel fuel has significantly reduced HC, CO, and smoke emissions but it increases the NOx emission slightly with standard injection timing. The NOX emission was decreased with retarded injection timing with negligible effect on fuel consumption rate. Similar trend in brake thermal efficiency and exhaust gas temperature was observed with retarded injection timing while maximum cylinder gas pressure and ignition delay was decreased.

Predicting the Engine Performance and Exhaust Emissions of a Diesel Engine Fueled With Hazelnut Oil Methyl Ester: The Performance Comparison of Response Surface Methodology and LSSVM

2016 ◽  
Vol 138 (5) ◽  
Author(s):  
Nadir Yilmaz ◽  
Erol Ileri ◽  
Alpaslan Atmanlı ◽  
A. Deniz Karaoglan ◽  
Umut Okkan ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Diesel Engine ◽  
Methyl Ester ◽  
Response Surface ◽  
Fuel Injection ◽  
Engine Performance ◽  
Experimental Results ◽  
Hazelnut Oil ◽  
Injection Timing ◽  
Fuel Injection Timing

An experimental investigation was conducted to evaluate the suitability of hazelnut oil methyl ester (HOME) for engine performance and exhaust emissions responses of a turbocharged direct injection (TDI) diesel engine. HOME was tested at full load with various engine speeds by changing fuel injection timing (12, 15, and 18 deg CA) in a TDI diesel engine. Response surface methodology (RSM) and least-squares support vector machine (LSSVM) were used for modeling the relations between the engine performance and exhaust emission parameters, which are the measured responses and factors such as fuel injection timing (t) and engine speed (n) parameters as the controllable input variables. For this purpose, RSM and LSSVM models from experimental results were constructed for each response, namely, brake power, brake-specific fuel consumption (BSFC), brake thermal efficiency (BTE), exhaust gas temperature (EGT), oxides of nitrogen (NOx), carbon dioxide (CO2), carbon monoxide (CO), and smoke opacity (N), which are affected by the factors t and n. The results of RSM and LSSVM were compared with the observed experimental results. These results showed that RSM and LSSVM were effective modeling methods with high accuracy for these types of cases. Also, the prediction performance of LSSVM was slightly better than that of RSM.

scholarly journals Experimental investigation on performance and emission characteristics of diesel - Jatropha methyl ester blends fueled diesel engine at optimum engine operating parameters

2010 ◽  
Vol 7 (2) ◽  
pp. 399-406 ◽  
Author(s):  
M. Venkatraman ◽  
G. Devaradjane
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Compression Ratio ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Injection Timing ◽  
Performance And Emission ◽  
Performance And Emissions ◽  
Blended Fuel

In the present investigation, tests were carried out to determine engine performance, combustion and emissions of a naturally aspirated direct injection diesel engine fueled with diesel and Jatropha Methyl ester and their blends (JME10, JME20 and JME30). Comparison of performance and emission was done for different values of compression ratio, injection pressure and injection timing to find best possible combination for operating engine with JME. It is found that the combined compression ratio of 19:1, injection pressure of 240 bar and injection timing of 27?bTDC increases the BTHE and reduces BSFC while having lower emissions.From the investigation, it is concluded that the both performance and emissions can considerably improved for Methyl ester of jatropha oil blended fuel JME20 compared to diesel.

scholarly journals Influence of Advanced Injection Timing and Fuel Additive on Combustion, Performance, and Emission Characteristics of a DI Diesel Engine Running on Plastic Pyrolysis Oil

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Ioannis Kalargaris ◽  
Guohong Tian ◽  
Sai Gu
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Timing ◽  
Fuel Additive ◽  
Pyrolysis Oil ◽  
Performance And Emission ◽  
Di Diesel Engine ◽  
Unburned Hydrocarbons ◽  
Promising Solution

This paper presents the investigation of engine optimisation when plastic pyrolysis oil (PPO) is used as the primary fuel of a direct injection diesel engine. Our previous investigation revealed that PPO is a promising fuel; however the results suggested that control parameters should be optimised in order to obtain a better engine performance. In the present work, the injection timing was advanced, and fuel additives were utilised to overcome the issues experienced in the previous work. In addition, spray characteristics of PPO were investigated in comparison with diesel to provide in-depth understanding of the engine behaviour. The experimental results on advanced injection timing (AIT) showed reduced brake thermal efficiency and increased carbon monoxide, unburned hydrocarbons, and nitrogen oxides emissions in comparison to standard injection timing. On the other hand, the addition of fuel additive resulted in higher engine efficiency and lower exhaust emissions. Finally, the spray tests revealed that the spray tip penetration for PPO is faster than diesel. The results suggested that AIT is not a preferable option while fuel additive is a promising solution for long-term use of PPO in diesel engines.

scholarly journals An Experimental Investigation on the Effect of Ferrous Ferric Oxide Nano-Additive and Chicken Fat Methyl Ester on Performance and Emission Characteristics of Compression Ignition Engine

Symmetry ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 265
Author(s):  
Ameer Suhel ◽  
Norwazan Abdul Rahim ◽  
Mohd Rosdzimin Abdul Rahman ◽  
Khairol Amali Bin Ahmad ◽  
Yew Heng Teoh ◽  
...  
Keyword(s):  
Methyl Ester ◽  
Ferric Oxide ◽  
Fossil Fuels ◽  
Specific Energy Consumption ◽  
Experimental Results ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Performance And Emission ◽  
Chicken Fat

In recent years, industries have been investing to develop a potential alternative fuel to substitute the depleting fossil fuels which emit noxious emissions. Present work investigated the effect of ferrous ferric oxide nano-additive on performance and emission parameters of compression ignition engine fuelled with chicken fat methyl ester blends. The nano-additive was included with various methyl ester blends at different ppm of 50, 100, and 150 through the ultrasonication process. Probe sonicator was utilized for nano-fuel preparation to inhibit the formation of agglomeration of nanoparticles in base fuel. Experimental results revealed that the addition of 100 ppm dosage of ferrous ferric oxide nanoparticles in blends significantly improves the combustion performance and substantially decrease the pernicious emissions of the engine. It is also found from an experimental results analysis that brake thermal efficiency (BTE) improved by 4.84%, a reduction in brake specific fuel consumption (BSFC) by 10.44%, brake specific energy consumption (BSEC) by 9.44%, exhaust gas temperature (EGT) by 19.47%, carbon monoxides (CO) by 53.22%, unburned hydrocarbon (UHC) by 21.73%, nitrogen oxides (NOx) by 15.39%, and smoke by 14.73% for the nano-fuel B20FFO100 blend. By seeing of analysis, it is concluded that the doping of ferrous ferric oxide nano-additive in chicken fat methyl ester blends shows an overall development in engine characteristics.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

scholarly journals Performance evaluation of common rail direct injection (CRDI) engine fuelled with Uppage Oil Methyl Ester (UOME)

2015 ◽  
Vol 4 (1) ◽  
pp. 1-10 ◽  
Author(s):  
D.N. Basavarajappa ◽  
N. R. Banapurmath ◽  
S.V. Khandal ◽  
G. Manavendra
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Engines ◽  
High Speed ◽  
Alternative Fuels ◽  
High Pressures ◽  
Fuel Injection ◽  
Injection Timing ◽  
Engine Operation ◽  
Performance And Emission

For economic and social development of any country energy is one of the most essential requirements. Continuously increasing price of crude petroleum fuels in the present days coupled with alarming emissions and stringent emission regulations has led to growing attention towards use of alternative fuels like vegetable oils, alcoholic and gaseous fuels for diesel engine applications. Use of such fuels can ease the burden on the economy by curtailing the fuel imports. Diesel engines are highly efficient and the main problems associated with them is their high smoke and NOx emissions.  Hence there is an urgent need to promote the use of alternative fuels in place of high speed diesel (HSD) as substitute. India has a large agriculture base that can be used as a feed stock to obtain newer fuel which is renewable and sustainable. Accordingly Uppage oil methyl ester (UOME) biodiesel was selected as an alternative fuel. Use of biodiesels in diesel engines fitted with mechanical fuel injection systems has limitation on the injector opening pressure (300 bar). CRDI system can overcome this drawback by injecting fuel at very high pressures (1500-2500 bar) and is most suitable for biodiesel fuels which are high viscous. This paper presents the performance and emission characteristics of a CRDI diesel engine fuelled with UOME biodiesel at different injection timings and injection pressures. From the experimental evidence it was revealed that UOME biodiesel yielded overall better performance with reduced emissions at retarded injection timing of -10° BTDC in CRDI mode of engine operation.

scholarly journals Comparison of performance of biodiesels of mahua oil and gingili oil in dual fuel engine

2008 ◽  
Vol 12 (1) ◽  
pp. 151-156 ◽  
Author(s):  
Kapilan Nadar ◽  
Pratap Reddy ◽  
Rao Anjuri
Keyword(s):  
Carbon Monoxide ◽  
Methyl Ester ◽  
Dual Fuel ◽  
Injection Timing ◽  
Nox Emissions ◽  
Test Results ◽  
Liquefied Petroleum Gas ◽  
Mahua Oil ◽  
Hydro Carbon ◽  
Pilot Fuel

In this work, an experimental work was carried out to compare the performance of biodiesels made from non edible mahua oil and edible gingili oil in dual fuel engine. A single cylinder diesel engine was modified to work in dual fuel mode and liquefied petroleum gas was used as primary fuel. Biodiesel was prepared by transesterification process and mahua oil methyl ester (MOME) and gingili oil methyl ester (GOME) were used as pilot fuels. The viscosity of MOME is slightly higher than GOME. The dual fuel engine runs smoothly with MOME and GOME. The test results show that the performance of the MOME is close to GOME, at the pilot fuel quantity of 0.45 kg/h and at the advanced injection timing of 30 deg bTDC. Also it is observed that the smoke, carbon monoxide and unburnt hydro carbon emissions of GOME lower than the MOME. But the GOME results in slightly higher NOx emissions. From the experimental results it is concluded that the biodiesel made from mahua oil can be used as a substitute for diesel in dual fuel engine.

Experimental Investigations of Performance and Emission Characteristics of Moringa Oil Methyl Ester and Its Diesel Blends in a Single Cylinder Direct Injection Diesel Engine

2009 ◽  
Author(s):  
Shyamsundar Rajaraman ◽  
G. K. Yashwanth ◽  
T. Rajan ◽  
R. Siva Kumaran ◽  
P. Raghu
Keyword(s):  
Diesel Engine ◽  
Alternative Fuels ◽  
Methyl Esters ◽  
Direct Injection ◽  
Engine Performance ◽  
Experimental Investigations ◽  
Emission Analysis ◽  
Performance And Emission ◽  
Direct Injection Diesel Engine ◽  
Moringa Oil

World at present is confronted with the twin crisis of fossil fuel depletion and environmental pollution. Rapid escalation in prices and hydrocarbon resources depletion has led us to look for alternative fuels, which can satisfy ever increasing demands of energy as well as protect the environment from noxious pollutants. In this direction an attempt has been made to study a biodiesel, namely Moringa Oil Methyl Esters [MOME]. All the experiments were carried out on a 4.4 kW naturally aspirated stationary direct injection diesel engine coupled with a dynamometer to determine the engine performance and emission analysis for MOME. It was observed that there was a reduction in HC, CO and PM emissions along with a substantial increase in NOx. MOME and its blends had slightly lower thermal efficiency than diesel oil.

Sign in / Sign up

Export Citation Format

Share Document