Experimental Study on the Fluctuation Characteristics of Pressure Drop and Mass Flux of the Two-Phase Flow in Narrow Channel

2013 ◽  
Author(s):  
Deqi Chen ◽  
Qinghua Wang ◽  
Zhengang Duan ◽  
Liang-ming Pan
Keyword(s):  
Liquid Phase ◽  
Pressure Drop ◽  
Gas Phase ◽  
Flow Rate ◽  
Mass Flux ◽  
Gas Flow ◽  
Working Fluid ◽  
Phase Flow ◽  
Two Phase ◽  
Liquid Mass

In this paper the study focuses on a visual investigation on the gas-water two-phase flow in a vertical circular narrow channel with 2 mm inner diameter under atmospheric pressure. Experiments were carried out with different working conditions, including different gases as gas-phase working fluids such as nitrogen, air, carbon dioxide and argon, and the gas flow rate, Q, varied between 0 ml/s (single liquid phase flow) to 9.0 ml/s, and the liquid mass flux, G, varied between 581.3 kg/m2s to 3201.8 kg/m2s. The influence of liquid mass flux, gas flow rate as well as Eo number and Mo number (using these two non-dimensional parameters to specify the effect of gas-phase properties) on the fluctuation of pressure drop and mass flux were investigated in this study. It is found that the pressure drop increases along with increasing liquid-phase flow rate with identical other working conditions, and the corresponding flow patterns are slug flow even though the liquid-phase flow rates are different. However, the pressure drop decreases at first and then increases along with gas-phase flow rate, with constant liquid flow rate (liquid mass flux), and the corresponding flow patterns include slug flow, slug-annular flow and annular flow. Based on the experimental result, it is also found that the smaller Eo number and Mo number of the gas-phase working fluid, the smaller the fluctuations of the pressure drop and mass flux would be due to the gas-phase working fluid is different.

scholarly journals Numerical Simulation of Flow Behavior within a Venturi Scrubber

2014 ◽  
Vol 2014 ◽  
pp. 1-7
Author(s):  
M. M. Toledo-Melchor ◽  
C. del C. Gutiérrez-Torres ◽  
J. A. Jiménez-Bernal ◽  
J. G. Barbosa-Saldaña ◽  
S. A. Martínez-Delgadillo ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Pressure Drop ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Gas Flow ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Venturi Scrubber

The present work details the three-dimensional numerical simulation of single-phase and two-phase flow (air-water) in a venturi scrubber with an inlet and throat diameters of 250 and 122.5 mm, respectively. The dimensions and operating parameters correspond to industrial applications. The mass flow rate conditions were 0.483 kg/s, 0.736 kg/s, 0.861 kg/s, and 0.987 kg/s for the gas only simulation; the mass flow rate for the liquid was 0.013 kg/s and 0.038 kg/s. The gas flow was simulated in five geometries with different converging and diverging angles while the two-phase flow was only simulated for one geometry. The results obtained were validated with experimental data obtained by other researchers. The results show that the pressure drop depends significantly on the gas flow rate and that water flow rate does not have significant effects neither on the pressure drop nor on the fluid maximum velocity within the scrubber.

Research on Two-Phase Flow Instability in Evaporator of Refrigeration System

2010 ◽  
Author(s):  
Nan Liang ◽  
Changqing Tian ◽  
Shuangquan Shao
Keyword(s):  
Pressure Drop ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Two Phase Flow ◽  
Density Wave ◽  
Phase Flow ◽  
Constant Mass ◽  
Refrigeration System ◽  
Two Phase

As one kind of fluid machinery related to the two-phase flow, the refrigeration system encounters more problems of instability. It is essential to ensure the stability of the refrigeration systems for the operation and efficiency. This paper presents the experimental investigation on the static and dynamic instability in an evaporator of refrigeration system. The static instability experiments showed that the oscillatory period and swing of the mixture-vapor transition point by observation with a camera through the transparent quartz glass tube at the outlet of the evaporator. The pressure drop versus mass flow rate curves of refrigerant two phase flow in the evaporator were obtained with a negative slope region in addition to two positive slope regions, thus making the flow rate a multi-valued function of the pressure drop. For dynamic instabilities in the evaporation process, three types of oscillations (density wave type, pressure drop type and thermal type) were observed at different mass flow rates and heat fluxes, which can be represented in the pressure drop versus mass flow rate curves. For the dynamic instabilities, density wave oscillations happen when the heat flux is high with the constant mass flow rate. Thermal oscillations happen when the heat flux is correspondingly low with constant mass flow rate. Though the refrigeration system do not have special tank, the accumulator and receiver provide enough compressible volume to induce the pressure drop oscillations. The representation and characteristic of each oscillation type were also analyzed in the paper.

Experimental, Numerical, and Statistical Investigation of Two Phase Flow in a Cylindrical Perforation Tunnel

2021 ◽  
Author(s):  
Ekhwaiter Abobaker ◽  
Abadelhalim Elsanoose ◽  
Mohammad Azizur Rahman ◽  
Faisal Khan ◽  
Amer Aborig ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Steady State ◽  
Statistical Analysis ◽  
Flow Rate ◽  
Gas Flow ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Gas Flow Rate ◽  
Two Phase ◽  
Flow Through

Abstract Perforation is the final stage in well completion that helps to connect reservoir formations to wellbores during hydrocarbon production. The drilling perforation technique maximizes the reservoir productivity index by minimizing damage. This can be best accomplished by attaining a better understanding of fluid flows that occur in the near-wellbore region during oil and gas operations. The present work aims to enhance oil recovery by modelling a two-phase flow through the near-wellbore region, thereby expanding industry knowledge about well performance. An experimental procedure was conducted to investigate the behavior of two-phase flow through a cylindrical perforation tunnel. Statistical analysis was coupled with numerical simulation to expand the investigation of fluid flow in the near-wellbore region that cannot be obtained experimentally. The statistical analysis investigated the effect of several parameters, including the liquid and gas flow rate, liquid viscosity, permeability, and porosity, on the injection build-up pressure and the time needed to reach a steady-state flow condition. Design-Expert® Design of Experiments (DoE) software was used to determine the numerical simulation runs using the ANOVA analysis with a Box-Behnken Design (BBD) model and ANSYS-FLUENT was used to analyses the numerical simulation of the porous media tunnel by applying the volume of fluid method (VOF). The experimental data were validated to the numerical results, and the comparison of results was in good agreement. The numerical and statistical analysis demonstrated each investigated parameter’s effect. The permeability, flow rate, and viscosity of the liquid significantly affect the injection pressure build-up profile, and porosity and gas flow rate substantially affect the time required to attain steady-state conditions. In addition, two correlations obtained from the statistical analysis can be used to predict the injection build-up pressure and the required time to reach steady state for different scenarios. This work will contribute to the clarification and understanding of the behavior of multiphase flow in the near-wellbore region.

Wet Gas Flow Metering Based on Differential Pressure and BSS Techniques

2011 ◽  
Vol 383-390 ◽  
pp. 4922-4927
Author(s):  
Peng Xia Xu ◽  
Yan Feng Geng
Keyword(s):  
Flow Rate ◽  
Liquid Flow ◽  
Gas Flow ◽  
Two Phase Flow ◽  
Liquid Flow Rate ◽  
Differential Pressure ◽  
Phase Flow ◽  
Two Phase ◽  
Flow Metering ◽  
Wet Gas

Wet gas flow is a typical two-phase flow with low liquid fractions. As differential pressure signal contains rich information of flow parameters in two-phase flow metering, a new method is proposed for wet gas flow metering based on differential pressure (DP) and blind source separation (BSS) techniques. DP signals are from a couple of slotted orifices and the BSS method is based on time-frequency analysis. A good relationship between the liquid flow rate and the characteristic quantity of the separated signal is established, and a differential pressure correlation for slotted orifice is applied to calculate the gas flow rate. The calculation results are good with 90% relative errors less than ±10%. The results also show that BSS is an effective method to extract liquid flow rate from DP signals of wet gas flow, and to analysis different interactions among the total DP readings.

Flow Structures and Frictional Characteristics on Two-Phase Flow in Microchannels in PEM Fuel Cells

2005 ◽  
Author(s):  
Eon Soo Lee ◽  
Carlos H. Hidrovo ◽  
Julie E. Steinbrenner ◽  
Fu-Min Wang ◽  
Sebastien Vigneron ◽  
...  
Keyword(s):  
Pressure Drop ◽  
Gas Phase ◽  
Single Phase ◽  
Film Flow ◽  
Two Phase Flow ◽  
Water Injection ◽  
Injection Rate ◽  
Flow Structures ◽  
Phase Flow ◽  
Two Phase

This experimental paper presents a study of gas-liquid two phase flow in rectangular channels of 500μm × 45μm and 23.7mm long with different wall conditions of hydrophilic and hydrophobic surface, in order to investigate the flow structures and the corresponding friction factors of simulated microchannels of PEMFC. The main flow in the channel is air and liquid water is injected at a single or several discrete locations in one side wall of the channel. The flow structure of liquid water in hydrophilic wall conditioned channel starts from wavy flow, develops to stable stratified film flow, and then transits to unstable fluctuating film flow, as the pressure drop and the flow velocity of air increase from around 10 kPa to over 100 kPa. The flow structure in hydrophobic channel develops from the slug flow to slug-and-film flow with increasing pressure drop and flow velocity. The pressure drop for single phase flow is measured for a base line study, and the fRe product is in close agreement with the theoretical value (fRe = 85) of the conventional laminar flow of aspect ratio 1:11. At the low range of water injection rate, the gas phase fRe product of the two phase flow based on the whole channel area was not substantially affected by the water introduction. However, as the water injection rate increases up to 100 μL/min, the gas phase fRe product based on the whole channel area deviates highly from the single phase theoretical value. The gas phase fRe product with the actual gas phase area corrected by the liquid phase film thickness agrees with the single phase theoretical value.

Pressure Drop in a Capillary Tube in Boiling Two-Phase Flow

2003 ◽  
Author(s):  
Fumito Kaminaga ◽  
Baduge Sumith ◽  
Kunihito Matsumura
Keyword(s):  
Pressure Drop ◽  
Vapor Phase ◽  
Mass Flux ◽  
Two Phase Flow ◽  
Capillary Tube ◽  
Flow Boiling ◽  
Phase Flow ◽  
Two Phase ◽  
System Pressure ◽  
Phase Pressure

Two-phase pressure drop is experimentally examined in a flow boiling condition in a tube of diameter 1.45 mm using water in ranges of pressure from 10 to 100 kPa, mass flux from 18 to 152 kg/m2s, heat flux from 13 to 646 kW/m2, and exit quality from 0.02 to 0.77. Also, pressure drop in an adiabatic air-water two-phase flow is measured at atmospheric pressure using the same test section and mass flux ranges of liquid and gas as those in the flow boiling. Decreasing system pressure the pressure drop significantly increases at a given mass flux. Influence of vapor phase on the pressure drop is found to be large both in the adiabatic and the diabatic conditions. The frictional pressure drop correlation for the adiabatic two-phase flow is developed and applied to predict pressure drop in the flow boiling. But it cannot give satisfactory predictions. The Chisholm correlation calculating a two-phase pressure drop multiplier is modified to account the influence of vapor phase in a capillary tube and the modified correlation can predict the pressure drop in the flow boiling within an error of 20%.

Visualization Study on Two-Phase Flow Behaviors in the Gas-Liquid-Solid Microreactor for Hydrogenation of Nitrobenzene

2016 ◽  
Author(s):  
Hao Feng ◽  
Xun Zhu ◽  
Rong Chen ◽  
Qiang Liao
Keyword(s):  
Flow Rate ◽  
Liquid Flow ◽  
Gas Flow ◽  
Two Phase Flow ◽  
Flow Direction ◽  
Flow Characteristics ◽  
Phase Flow ◽  
Microchannel Reactor ◽  
Two Phase ◽  
Modified Surface

In this study, visualization study on the gas-liquid two phase flow characteristics in a gas-liquid-solid microchannel reactor was carried out. Palladium nanocatalyst was coated onto the polydopamine functionalized surface of the microchannel through eletroless deposition. The materials characterization results indicated that palladium nanocatalyst were well dispersed on the modified surface. The effects of both the gas and liquid flow rates as well as inlet nitrobenzene concentration on the two-phase flow characteristics were studied. The experimental results revealed that owing to the chemical reaction inside the microreactor, the gas slug length gradually decreased along the flow direction. For a given inlet nitrobenzene concentration, increasing the liquid flow rate or decreasing the gas flow rate would make the variation of the gas slug length more obvious. High inlet nitrobenzene concentration would intensify both the nitrobenzene transfer efficiency and gas reactants consumption, and thereby the flow pattern in the microchannel was transferred from Taylor flow into bubble flow. Besides, the effect of both flow rate and original nitrobenzene concentration on the variation of nitrobenzene conversion and the desired product aniline yield were also discussed.

scholarly journals Numerical Simulation of Gas-Particle Two-Phase Flow in a Nozzle with DG Method

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Duan Maochang ◽  
Yu Xijun ◽  
Chen Dawei ◽  
Qing Fang ◽  
Zou Shijun
Keyword(s):  
Flow Field ◽  
Gas Phase ◽  
Mass Fraction ◽  
Gas Flow ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Governing Equations ◽  
Two Phase ◽  
Dg Method ◽  
The Impact

In this paper, the discontinuous Galerkin (DG) method is applied to solve the governing equations of the dispersed two-phase flow with the two-fluid Euler/Euler approach. The resulting governing equations are simple in form and the solution process is very natural. The characteristics of the gas-particle two-phase flow in an engine nozzle are mainly analyzed, and the impacts of the particle mass fraction and particle size on the flow field and engine performance are evaluated. Because of the addition of particles, the gas flow field undergoes significant modifications. Increase in the mass fraction leads to a significant thrust loss in the gas phase, and the impact of the particles on the gas phase could be substantial. Therefore, a quantitative study of thrust loss in the nozzle due to the particle impact is made. It is found that the gas thrust in the two-phase flow is reduced, but the total thrust of the two-phase flow increases to a certain extent.

Experimental Research on Pulsating Two-Phase Flow Pressure Drop Characteristics in Horizontal Rectangular Channel

2014 ◽  
Author(s):  
Siqi Zhang ◽  
Puzhen Gao
Keyword(s):  
Pressure Drop ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Two Phase Flow ◽  
Rectangular Channel ◽  
Phase Flow ◽  
Two Phase ◽  
Mean Values ◽  
Water Mass Flow Rate

In spite of most previous studies since 1970, the theory of pulsating pipe flows supported by experimental investigations has not yet completed in comparison with the well-defined theory of steady pipe flows. Therefore, it seems that there is much to be done about experimental research in this field. In order to determine the resistance characteristics of two-phase flow under pulsatile conditions, an experimental investigation on two-phase flow with periodically fluctuating flow rates in a narrow rectangular channel is carried out. A frequency inverter is used to obtain experimental conditions with different fluctuating frequencies, amplitudes and mean values of water mass flow rate. After obtaining experimental results, comparisons between experimental frictional pressure drop values and theoretical calculations have been done. Two-phase flow on pulsating conditions is far more complicated than that on steady conditions because pulsating flow is composed of two parts: a steady component and a superimposed periodical time varying component called oscillation. In this paper, the influence of different fluctuating frequencies, amplitudes and mean values of liquid and gas mass flow rate on two-phase flow pressure drop characteristics is also discussed. The results show that the total pressure drop and water mass flow rate change with the same fluctuating period except for a phase difference. The phase lag also changes with the fluctuating frequencies and amplitude. The accelerating pressure drop changes dramatically in a fluctuating period, especially at the end of acceleration. Also, the time when the acceleration pressure drop has its maximum value lags the time when the acceleration reaches its peak, mainly because of the inertial of the fluid.

Machine Learning Approach to Predict the Flow Rate for an Immiscible Two-Phase Flow at Pore Scale for Enhanced Oil Recovery Application

2018 ◽  
Author(s):  
Arturo Rodriguez ◽  
V. M. Krushnarao Kotteda ◽  
Luis F. Rodriguez ◽  
Vinod Kumar ◽  
Arturo Schiaffino ◽  
...  
Keyword(s):  
Machine Learning ◽  
Surface Tension ◽  
Pressure Drop ◽  
Flow Rate ◽  
Oil Recovery ◽  
Two Phase Flow ◽  
Machine Learning Algorithms ◽  
Phase Flow ◽  
Pore Scale ◽  
Two Phase

Due to global demand for energy, there is a need to maximize oil extraction from wet reservoir sedimentary formations, which implies the efficient extraction of oil at the pore scale. The approach involves pressurizing water into the wetting oil pore of the rock for displacing and extracting the oil. The two-phase flow is complicated because of the behavior of the fluid flow at the pore scale, and capillary quantities such as surface tension, viscosities, pressure drop, radius of the medium, and contact angle become important. In the present work, we use machine learning algorithms in TensorFlow to predict the volumetric flow rate for a given pressure drop, surface tension, viscosity and geometry of the pores. The TensorFlow software library was developed by the Google Brain team and is one of the most powerful tools for developing machine learning workflows. Machine learning models can be trained on data and then these models are used to make predictions. In this paper, the predicted values for a two-phase flow of various pore sizes and liquids are validated against the numerical and experimental results in the literature.

Sign in / Sign up

Export Citation Format

Share Document