Investigation of Turbulence Modeling in a High Speed Centrifugal Pump With an Inducer

2007 ◽  
Author(s):  
Behrooz Jafarzadeh ◽  
Reza Mokhtarpoor ◽  
Mohammad Mehdi Alishahi ◽  
Mohammad Hadi Akbari
Keyword(s):  
Centrifugal Pump ◽  
High Speed ◽  
Turbulence Modeling ◽  
Flow Direction ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Governing Equations ◽  
Flow Rates ◽  
Pressure Fields ◽  
Three Dimensional Simulations

In this paper, investigation of turbulence modeling for a centrifugal pump is presented in the form of characteristic curves. A commercial CFD code was used to solve the governing equations of the flow field. Turbulent flow is simulated by employing standard k-ε, RNG and RSM models. Existence of an inducer in the flow direction to prevent cavitation makes two-dimensional simulations of the present configuration impossible. Three-dimensional simulations were therefore performed to predict velocity and pressure fields at different flow rates. Considering the only one available experimental data, the optimum turbulence model for the problem was found. Additionally, effect of number of blades on the efficiency of pump was studied. The number of blades was changed from 6 to 5 and 7, then all calculations were performed afresh. Investigations of this kind may help reduce the required experimental work for the development and design of such devices.

Comparison of Inlet Curved Disk Arrangements for Suppression of Recirculation in Centrifugal Pump Impellers

2016 ◽  
Author(s):  
Munther Y. Hermez ◽  
Badih A. Jawad ◽  
Liping Liu ◽  
Vernon Fernandez ◽  
Kingman Yee ◽  
...  
Keyword(s):  
Centrifugal Pump ◽  
High Speed ◽  
Operating Cost ◽  
Three Dimensional ◽  
Centrifugal Pumps ◽  
Unstable Flow ◽  
Pump Impeller ◽  
Flow Rates ◽  
Flow Recirculation ◽  
Flow Field Characteristics

The present work aims to numerically study the inlet flow recirculation and modified impeller interaction in a centrifugal pump. An optimization of modified shrouded impeller with curved disk arrangement to suppress the unsteady flow recirculation is pursued. This modification will enhance the impeller characteristics with a wider operation range at both low and high flow rates in a high speed centrifugal pump type. The unstable flow in the centrifugal pumps is a common problem that leads to damage in the pump’s internal parts, consequently increases the operating cost. At certain flow rates, generally below the Best Efficiency Point (BEP), all centrifugal pumps are subject to internal recirculation occurs at the suction and discharge areas of the impeller. For decades, experimental work has been done to investigate the complex three-dimensional flow within centrifugal pumps impellers, before computational work gains momentum due to advancement of computing power and improved numerical codes. In this study the impeller with a curved disk arrangement has been investigated by using a three-dimensional Navier-Stokes code with a standard k-ε turbulence model. The purpose is to evaluate and select the optimum impeller modification that would increase the pump suction flow rate range. Three-dimensional numerical Computational Fluid Dynamics (CFD) tools are used to simulate flow field characteristics inside the centrifugal pump and provide critical hydraulic design information. In the present work, ANSYS v.16.1 Fluent solver is used to analyze the pressure and velocity distributions inside impeller suction and discharge passages. The ultimate goal of this study is to manufacture and validate the most optimized and efficient centrifugal pump impeller with a curved disk. The best case curve identifies the highest increase of total pressure difference by 22.1%, and highest efficiency by 92.3% at low flowrates.

Bifurcation Characteristics of Flows in Rectangular Sudden Expansion Channels

2005 ◽  
Author(s):  
Francine Battaglia ◽  
George Papadopoulos
Keyword(s):  
Reynolds Number ◽  
Laminar Flow ◽  
Critical Reynolds Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Expansion Ratio ◽  
Sudden Expansion ◽  
Two Dimensional ◽  
Effective Expansion ◽  
Three Dimensional Simulations

The effect of three-dimensionality on low Reynolds number flows past a symmetric sudden expansion in a channel was investigated. The geometric expansion ratio of in the current study was 2:1 and the aspect ratio was 6:1. Both experimental velocity measurements and two- and three-dimensional simulations for the flow along the centerplane of the rectangular duct are presented for Reynolds numbers in the range of 150 to 600. Comparison of the two-dimensional simulations with the experiments revealed that the simulations fail to capture completely the total expansion effect on the flow, which couples both geometric and hydrodynamic effects. To properly do so requires the definition of an effective expansion ratio, which is the ratio of the downstream and upstream hydraulic diameters and is therefore a function of both the expansion and aspect ratios. When the two-dimensional geometry was consistent with the effective expansion ratio, the new results agreed well with the three-dimensional simulations and the experiments. Furthermore, in the range of Reynolds numbers investigated, the laminar flow through the expansion underwent a symmetry-breaking bifurcation. The critical Reynolds number evaluated from the experiments and the simulations was compared to other values reported in the literature. Overall, side-wall proximity was found to enhance flow stability, helping to sustain laminar flow symmetry to higher Reynolds numbers in comparison to nominally two-dimensional double-expansion geometries. Lastly, and most importantly, when the logarithm of the critical Reynolds number from all these studies was plotted against the reciprocal of the effective expansion ratio, a linear trend emerged that uniquely captured the bifurcation dynamics of all symmetric double-sided planar expansions.

scholarly journals CAD Tools and Computing in Architectural and Urban Acoustics

Buildings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 235
Author(s):  
Joanna Jablonska ◽  
Roman Czajka
Keyword(s):  
Computer Aided Design ◽  
Three Dimensional ◽  
Computing Methods ◽  
Building Industry ◽  
Two Dimensional ◽  
Cad Tools ◽  
Architectural Acoustics ◽  
Urban Level ◽  
Aided Design ◽  
Three Dimensional Simulations

Contemporary architectural and urban planning aims at optimal development of the environment, including in terms of acoustics. As such, support with computer-aided design (CAD) tools is, nowadays, obligatory. The authors present investigation outcomes of three different CAD and computing methods extracted for the study. The scope covers different scales of considerations from architectural acoustics to the urban level, which relates to the standard architect’s commissions field. The described approaches are applicable for both academics and professionals in the broadly understood building industry There were analysed and synthesized experiences from the use of two-dimensional and three-dimensional simulations, computing based on standardized formulas, and an acoustic meter (here: the SVAN 979 for RT60, LAeq measurement). The article concludes with an assessment, which shows possible uses of methods and confirmations of their usability.

Review of Three Dimensional Dynamic Analyses of Circular Cylinders and Cylindrical Shells

1994 ◽  
Vol 47 (10) ◽  
pp. 501-516 ◽  
Author(s):  
Kostas P. Soldatos
Keyword(s):  
Cylindrical Shells ◽  
Three Dimensional ◽  
Circular Cylinders ◽  
Accurate Information ◽  
Two Dimensional ◽  
Governing Equations ◽  
Complicated Form ◽  
Dynamic Analyses ◽  
Cylindrical Panels ◽  
Elastic Cylinders

There is an increasing usefulness of exact three-dimensional analyses of elastic cylinders and cylindrical shells in composite materials applications. Such analyses are considered as benchmarks for the range of applicability of corresponding studies based on two-dimensional and/or finite element modeling. Moreover, they provide valuable, accurate information in cases that corresponding predictions based on that later kind of approximate modeling is not satisfactory. Due to the complicated form of the governing equations of elasticity, such three-dimensional analyses are comparatively rare in the literature. There is therefore a need for further developments in that area. A survey of the literature dealing with three-dimensional dynamic analyses of cylinders and open cylindrical panels will serve towards such developments. This paper presents such a survey within the framework of linear elasticity.

scholarly journals An experimental and theoretical investigation of particle–wall impacts in a T-junction

2013 ◽  
Vol 727 ◽  
pp. 236-255 ◽  
Author(s):  
D. Vigolo ◽  
I. M. Griffiths ◽  
S. Radl ◽  
H. A. Stone
Keyword(s):  
Flow Direction ◽  
Three Dimensional ◽  
Stokes Number ◽  
Two Dimensional ◽  
Dimensional Model ◽  
Viscous Boundary Layer ◽  
Particle Tracing ◽  
Two Dimensional Model ◽  
Viscous Boundary ◽  
The Impact

AbstractUnderstanding the behaviour of particles entrained in a fluid flow upon changes in flow direction is crucial in problems where particle inertia is important, such as the erosion process in pipe bends. We present results on the impact of particles in a T-shaped channel in the laminar–turbulent transitional regime. The impacting event for a given system is described in terms of the Reynolds number and the particle Stokes number. Experimental results for the impact are compared with the trajectories predicted by theoretical particle-tracing models for a range of configurations to determine the role of the viscous boundary layer in retarding the particles and reducing the rate of collision with the substrate. In particular, a two-dimensional model based on a stagnation-point flow is used together with three-dimensional numerical simulations. We show how the simple two-dimensional model provides a tractable way of understanding the general collision behaviour, while more advanced three-dimensional simulations can be helpful in understanding the details of the flow.

scholarly journals Quasi-two-dimensional approximation for numerical simulation of flows in engine ducts

2019 ◽  
Author(s):  
V. Vlasenko ◽  
A. Shiryaeva
Keyword(s):  
High Speed ◽  
Fuel Injection ◽  
Three Dimensional ◽  
Preliminary Design ◽  
Two Dimensional ◽  
Combustion Chambers ◽  
New Approach ◽  
One Dimensional ◽  
Dimensional Approximation ◽  
3D Flows

New quasi-two-dimensional (2.5D) approach to description of three-dimensional (3D) flows in ducts is proposed. It generalizes quasi-one-dimensional (quasi-1D, 1.5D) theories. Calculations are performed in the (x; y) plane, but variable width of duct in the z direction is taken into account. Derivation of 2.5D approximation equations is given. Tests for verification of 2.5D calculations are proposed. Parametrical 2.5D calculations of flow with hydrogen combustion in an elliptical combustor of a high-speed aircraft, investigated within HEXAFLY-INT international project, are described. Optimal scheme of fuel injection is found and explained. For one regime, 2.5D and 3D calculations are compared. The new approach is recommended for use during preliminary design of combustion chambers.

Two- and Three-Dimensional Simulations of the Flow Around a Cylinder Fitted With Strakes

2012 ◽  
Author(s):  
Bruno S. Carmo ◽  
Rafael S. Gioria ◽  
Ivan Korkischko ◽  
Cesar M. Freire ◽  
Julio R. Meneghini
Keyword(s):  
Reynolds Number ◽  
Vortex Shedding ◽  
Free Stream ◽  
Three Dimensional ◽  
The Body ◽  
Vortex Wake ◽  
Two Dimensional ◽  
Flow Around A Cylinder ◽  
Three Dimensional Simulations ◽  
Angle Of Rotation

Two- and three-dimensional simulations of the flow around straked cylinders are presented. For the two-dimensional simulations we used the Spectral/hp Element Method, and carried out simulations for five different angles of rotation of the cylinder with respect to the free stream. Fixed and elastically-mounted cylinders were tested, and the Reynolds number was kept constant and equal to 150. The results were compared to those obtained from the simulation of the flow around a bare cylinder under the same conditions. We observed that the two-dimensional strakes are not effective in suppressing the vibration of the cylinders, but also noticed that the responses were completely different even with a slight change in the angle of rotation of the body. The three-dimensional results showed that there are two mechanisms of suppression: the main one is the decrease in the vortex shedding correlation along the span, whilst a secondary one is the vortex wake formation farther downstream.

Experimental Study on Gravity Driven Discharging of Quasi-Two-Dimensional Pebble Bed Based on Mathematical Morphology

2020 ◽  
Author(s):  
Yujia Liu ◽  
Sifan Peng ◽  
Nan Gui ◽  
Xingtuan Yang ◽  
Jiyuan Tu ◽  
...  
Keyword(s):  
Experimental Study ◽  
Mathematical Morphology ◽  
High Speed ◽  
Three Dimensional ◽  
Reactor Core ◽  
Engineering Application ◽  
Discharge Process ◽  
Two Dimensional ◽  
Pebble Bed ◽  
Gravity Driven

Abstract The pebbles flow is a fundamental issue for both academic investigation and engineering application in reactor core design and safety analysis. In general, experimental methods including spiral X-ray tomography and refractive index matched scanning technique (RIMS) are applied to obtain the identification of particles’ positions within a three-dimensional pebble bed. However, none of the above methods can perform global bed particles’ position identification in a dynamically discharging pebble bed, and the corresponding experimental equipment is difficult to access due to the complication and high expense. In this research, the experimental study is conducted to observe the gravity driven discharging process in the quasi two-dimensional silos by making use of the high-speed camera and the uniform backlight. A mathematical morphology-based method is applied to the pre-processing of the captured results. After being increased the gray value gradient by the threshold segmentation, the edges of the particles are identified and smoothed by the Sobel algorithm and the morphological opening operation. The particle centroid coordinates are identified according to the Hough circle transformation of the edges. For the whole pebble bed, the self-programmed process has a particle recognition accuracy of more than 99% and a particle centroid position deviation of less than 3%, which can accurately obtain the physical positions of all particles in the entire dynamically discharge process. By analyzing the position evolution of individual particles in consecutive images, velocity field and motion events of particles are observed. The discharging profiles of 5 conditions with different exit are analyzed in this experiment. The results make a contribution to improving the understanding of the mechanism of pebbles flow in nuclear engineering.

scholarly journals Computational Study of Zigzag Spacer Design with Elliptical Cross-Section Filaments

2020 ◽  
Vol 307 ◽  
pp. 01047
Author(s):  
Gohar Shoukat ◽  
Farhan Ellahi ◽  
Muhammad Sajid ◽  
Emad Uddin
Keyword(s):  
Mass Transfer ◽  
Cross Section ◽  
Cross Sections ◽  
Computational Study ◽  
Flow Direction ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Two Dimensional ◽  
Permeate Flux ◽  
Elliptical Cross

The large energy consumption of membrane desalination process has encouraged researchers to explore different spacer designs using Computational Fluid Dynamics (CFD) for maximizing permeate per unit of energy consumed. In previous studies of zigzag spacer designs, the filaments are modeled as circular cross sections in a two-dimensional geometry under the assumption that the flow is oriented normal to the filaments. In this work, we consider the 45° orientation of the flow towards the three-dimensional zigzag spacer unit, which projects the circular cross section of the filament as elliptical in a simplified two-dimensional domain. OpenFOAM was used to simulate the mass transfer enhancement in a reverse-osmosis desalination unit employing spiral wound membranes lined with zigzag spacer filaments. Properties that impact the concentration polarization and hence permeate flux were analyzed in the domain with elliptical filaments as well as a domain with circular filaments to draw suitable comparisons. The range of variation in characteristic parameters across the domain between the two different configurations is determined. It was concluded that ignoring the elliptical projection of circular filaments to the flow direction, can introduce significant margin of error in the estimation of mass transfer coefficient.

Sign in / Sign up

Export Citation Format

Share Document