scholarly journals Investigation of a Multiple Impeller Design for a High Performance Air-Cooled Heat Sink

2010 ◽  
Author(s):  
Wayne L. Staats ◽  
Teresa B. Peters ◽  
Jon M. Allison ◽  
Matthew McCarthy ◽  
Evelyn N. Wang ◽  
...  
Keyword(s):  
Heat Sink ◽  
High Performance ◽  
Inflation Rate ◽  
Air Flow ◽  
Single Layer ◽  
Circuit Model ◽  
Flow Modeling ◽  
Hot Wire ◽  
Layer System ◽  
Flow Circuit

A high-performance air-cooled heat sink that incorporates a novel heat pipe with multiple parallel condenser layers and interdigitated blower impellers is presented. A flow circuit model was developed in order to predict the air flow performance of a 15-layer impeller system using experimental measurements from a single layer. A 15-layer impeller system was constructed to validate the flow circuit model. The performance of the multi-layer system was investigated by using a hot wire anemometer to compare flow between layers and by measuring the inflation rate of a bag enclosing the air outlets. This work addresses important issues that allow the extension of the air flow modeling and experimental results from a single impeller design to a multilayer stack of impellers operating in parallel and sharing a common inlet.

Dynamic Countermeasure Fabrics for Post-Spaceflight Orthostatic Intolerance

2020 ◽  
Vol 91 (6) ◽  
pp. 525-531 ◽  
Author(s):  
Rachael M. Granberry ◽  
Kevin P. Eschen ◽  
Amy J. Ross ◽  
Julianna M. Abel ◽  
Bradley T. Holschuh
Keyword(s):  
Double Layer ◽  
High Performance ◽  
Orthostatic Intolerance ◽  
Dynamic Compression ◽  
Single Layer ◽  
Design Parameters ◽  
Layer System ◽  
Compression Garments ◽  
Air Supply ◽  
Low Profile

INTRODUCTION: Aerospace orthostatic intolerance garments (OIG) have historically been pneumatic (e.g., NASA’s antigravity suit), an approach that inhibits mobility and requires connection to an air supply. Elastic compression garments, an alternative technology, are difficult to don/doff and cannot be worn in a noncompressive state, resulting in discomfort and usability challenges. This research evaluates a novel technology—contractile shape memory alloy (SMA) knitted actuators—that can enable low-profile, dynamic compression for an aerospace OIG.METHODS: To characterize the functional capabilities of SMA knitted actuators, displacement control testing was conducted on 10 actuator samples with a range of geometric design parameters. Inactive (FI) and actuated forces (FA) were observed by repeatedly thermally cycling each sample at 0%, 15%, 30%, and 45% structural strain. Compression capabilities were approximated using medical compression hosiery standards and anthropometric data from a representative aerospace population (ANSUR 2012).RESULTS: Dynamic compression predictions reached 52 mmHg (single layer fabric) and 105 mmHg (double layer fabric) at the ankle. Low, inactive pressures (p < 20 mmHg) demonstrate that compression is controllable and can be dynamically increased upon actuation up to 33 mmHg in a single layer system and up to 67 mmHg in a double layer system.DISCUSSION: The results highlight the potential of SMA knitted actuators to enable low-profile, dynamic compression garments that can reach medically therapeutic pressures on an aerospace population to counteract OI symptoms. In addition to astronautic applications, this technology demonstrates widespread terrestrial medical and high-performance aircraft applicability.Granberry RM, Eschen KP, Ross AJ, Abel JM, Holschuh BT. Dynamic countermeasure fabrics for post-spaceflight orthostatic intolerance. Aerosp Med Hum Perform. 2020; 91(6):525–531.

Discrete element method to model cracking for two layer systems

TAPPI Journal ◽  
2019 ◽  
Vol 18 (2) ◽  
pp. 101-108
Author(s):  
Daniel Varney ◽  
Douglas Bousfield
Keyword(s):  
Discrete Element Method ◽  
Flexural Modulus ◽  
Single Layer ◽  
Discrete Element ◽  
Flexural Stress ◽  
Layer System ◽  
Three Point Bending ◽  
Moving Force ◽  
Coating Layers ◽  
Element Method

Cracking at the fold is a serious issue for many grades of coated paper and coated board. Some recent work has suggested methods to minimize this problem by using two or more coating layers of different properties. A discrete element method (DEM) has been used to model deformation events for single layer coating systems such as in-plain and out-of-plain tension, three-point bending, and a novel moving force picking simulation, but nothing has been reported related to multiple coating layers. In this paper, a DEM model has been expanded to predict the three-point bending response of a two-layer system. The main factors evaluated include the use of different binder systems in each layer and the ratio of the bottom and top layer weights. As in the past, the properties of the binder and the binder concentration are input parameters. The model can predict crack formation that is a function of these two sets of factors. In addition, the model can predict the flexural modulus, the maximum flexural stress, and the strain-at-failure. The predictions are qualitatively compared with experimental results reported in the literature.

scholarly journals Bilayer ventilated labyrinthine metasurfaces with high sound absorption and tunable bandwidth

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Jiayuan Du ◽  
Yuezhou Luo ◽  
Xinyu Zhao ◽  
Xiaodong Sun ◽  
Yanan Song ◽  
...  
Keyword(s):  
Sound Absorption ◽  
Air Flow ◽  
Single Layer ◽  
Sound Waves ◽  
Acoustic Metamaterials ◽  
Sound Barrier ◽  
Free Air ◽  
Relative Bandwidth ◽  
Wide Range ◽  
High Sound

AbstractThe recent advent of acoustic metamaterials offers unprecedented opportunities for sound controlling in various occasions, whereas it remains a challenge to attain broadband high sound absorption and free air flow simultaneously. Here, we demonstrated, both theoretically and experimentally, that this problem can be overcome by using a bilayer ventilated labyrinthine metasurface. By altering the spacing between two constituent single-layer metasurfaces and adopting asymmetric losses in them, near-perfect (98.6%) absorption is achieved at resonant frequency for sound waves incident from the front. The relative bandwidth of absorption peak can be tuned in a wide range (from 12% to 80%) by adjusting the open area ratio of the structure. For sound waves from the back, the bilayer metasurface still serves as a sound barrier with low transmission. Our results present a strategy to realize high sound absorption and free air flow simultaneously, and could find applications in building acoustics and noise remediation.

scholarly journals 2D MoS2 Encapsulated Silicon Nanopillar Array with High-Performance Light Trapping Obtained by Direct CVD Process

Crystals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 267
Author(s):  
Minyu Bai ◽  
Zhuoman Wang ◽  
Jijie Zhao ◽  
Shuai Wen ◽  
Peiru Zhang ◽  
...  
Keyword(s):  
Silicon Substrate ◽  
High Performance ◽  
Low Cost ◽  
Light Trapping ◽  
Incident Light ◽  
Single Layer ◽  
Chemical Vapor ◽  
Optoelectronic Device ◽  
Planar Silicon ◽  
Shortwave Infrared

Weak absorption remains a vital factor that limits the application of two-dimensional (2D) materials due to the atomic thickness of those materials. In this work, a direct chemical vapor deposition (CVD) process was applied to achieve 2D MoS2 encapsulation onto the silicon nanopillar array substrate (NPAS). Single-layer 2D MoS2 monocrystal sheets were obtained, and the percentage of the encapsulated surface of NPAS was up to 80%. The reflection and transmittance of incident light of our 2D MoS2-encapsulated silicon substrate within visible to shortwave infrared were significantly reduced compared with the counterpart planar silicon substrate, leading to effective light trapping in NPAS. The proposed method provides a method of conformal deposition upon NPAS that combines the advantages of both 2D MoS2 and its substrate. Furthermore, the method is feasible and low-cost, providing a promising process for high-performance optoelectronic device development.

Thermal Behaviors of Passively-Cooled Hybrid Fin Heat Sinks for Lightweight and High Performance Thermal Management

2015 ◽  
Author(s):  
Nico Setiawan Effendi ◽  
Kyoung Joon Kim
Keyword(s):  
Thermal Resistance ◽  
Heat Sink ◽  
High Performance ◽  
Heat Dissipation ◽  
Computational Study ◽  
Heat Sinks ◽  
Channel Diameter ◽  
Internal Channel ◽  
Study Results ◽  
Parametric Effects

A computational study is conducted to explore thermal performances of natural convection hybrid fin heat sinks (HF HSs). The proposed HF HSs are a hollow hybrid fin heat sink (HHF HS) and a solid hybrid fin heat sink (SHF HS). Parametric effects such as a fin spacing, an internal channel diameter, a heat dissipation on the performance of HF HSs are investigated by CFD analysis. Study results show that the thermal resistance of the HS increases while the mass-multiplied thermal resistance of the HS decreases associated with the increase of the channel diameter. The results also shows the thermal resistance of the SHF HS is 13% smaller, and the mass-multiplied thermal resistance of the HHF HS is 32% smaller compared with the pin fin heat sink (PF HS). These interesting results are mainly due to integrated effects of the mass-reduction, the surface area enhancement, and the heat pumping via the internal channel. Such better performances of HF HSs show the feasibility of alternatives to the conventional PF HS especially for passive cooling of LED lighting modules.

Well-Aligned Graphene Oxide Nanosheets Decorated with Zinc Oxide Nanocrystals for High Performance Photocatalytic Application

2015 ◽  
Vol 14 (03) ◽  
pp. 1550007 ◽  
Author(s):  
K. Kaviyarasu ◽  
C. Maria Magdalane ◽  
E. Manikandan ◽  
M. Jayachandran ◽  
R. Ladchumananandasivam ◽  
...  
Keyword(s):  
Zinc Oxide ◽  
Graphene Oxide ◽  
High Performance ◽  
Chemical Reduction ◽  
Visible Region ◽  
Single Layer ◽  
Single Layer Graphene ◽  
Graphene Oxides ◽  
X Ray ◽  
Nanoscale Structures

Graphene oxide (GO) nanosheets modified with zinc oxide nanocrystals were achieved by a green wet-chemical approach. As-obtained products were characterized by XRD, Raman spectra, XPS, HR-TEM, EDS, PL and Photocatalytic studies. XRD studies indicate that the GO nanosheet have the same crystal structure found in hexagonal form of ZnO . The enhanced Raman spectrum of 2D bands confirmed formation of single layer graphene oxides. The gradual photocatalytic reduction of the GO nanosheet in the GO : ZnO suspension of ethanol was studied by using X-ray photoelectron (XPS) spectroscopy. The nanoscale structures were observed and confirmed using high resolution transmission electron microscopy (HR-TEM). The evolution of the elemental composition, especially the various numbers of layers were determined from energy dispersive X-ray spectra (EDS). PL properties of GO : ZnO nanosheet were found to be dependent on the growth condition and the resultant morphology revealed that GO nanosheet were highly transparent in the visible region. The photocatalytic performance of GO : ZnO nanocomposites was performed under UV irradiation. Therefore, the ZnO nanocrystals in the GO : ZnO composite could be applied in gradual chemical reduction and consequently tuning the electrical conductivity of the graphene oxide nanosheet.

Sign in / Sign up

Export Citation Format

Share Document