Effect of Design Parameters on Lubrication Behavior of Spur Gear Pairs

2017 ◽  
Author(s):  
Yanfang Liu ◽  
Qiang Liu ◽  
Peng Dong
Keyword(s):  
Power Loss ◽  
Elastohydrodynamic Lubrication ◽  
Spur Gear ◽  
Design Parameters ◽  
Curvature Radius ◽  
Gear Pair ◽  
Sliding Velocity ◽  
Rolling Velocity ◽  
Lubrication Performance ◽  
Meshing Process

An involute spur gear pair meshing model is firstly provided in this study to achieve relevant data such as rolling velocity, sliding velocity, curvature radius etc. These data are needed in a transient, Newtonian elastohydrodynamic lubrication (EHL) model which is provided later. Based on these two models, the behavior of an engaged spur gear pair during the meshing process is investigated under dynamic conditions, film thickness, pressure, friction coefficient etc. could be achieved through the models. Then, power loss under certain operating condition is calculated. Relationship between power loss and lubrication performance is also analyzed.

Oil Churning Power Losses of a Gear Pair: Experiments and Model Validation

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
S. Seetharaman ◽  
A. Kahraman ◽  
M. D. Moorhead ◽  
T. T. Petry-Johnson
Keyword(s):  
Power Loss ◽  
Spur Gear ◽  
Companion Paper ◽  
Design Parameters ◽  
Measured Parameter ◽  
Gear Pair ◽  
Power Losses ◽  
Gear Design ◽  
Face Width ◽  
Wide Range

This paper presents the results of an experimental study on load-independent (spin) power losses of spur gear pairs operating under dip-lubricated conditions. The experiments were performed over a wide range of operating speed, temperature, oil levels, and key gear design parameters to quantify their influence on spin power losses. The measurements indicate that the static oil level, rotational speed, and face width of gears have a significant impact on spin power losses compared with other parameters such as oil temperature, gear module, and the direction of gear rotation. A physics-based gear pair spin power loss formulation that was proposed in a companion paper (Seetharaman and Kahraman, 2009, “Load-Independent Spin Power Losses of a Spur Gear Pair: Model Formulation,” ASME J. Tribol., 131, p. 022201) was used to simulate these experiments. Direct comparisons between the model predictions and measurements are provided at the end to demonstrate that the model is capable of predicting the measured spin power loss values as well as the measured parameter sensitivities reasonably well.

A Computational Study on the Mechanical Power Loss of a Spur Gear Pair Under the Thermal Tribo-Dynamic Condition

2015 ◽  
Author(s):  
Sheng Li
Keyword(s):  
Power Loss ◽  
Computational Study ◽  
Dynamic Condition ◽  
Elastohydrodynamic Lubrication ◽  
Static Condition ◽  
Spur Gear ◽  
Mechanical Power ◽  
Gear Pair ◽  
Gear Mesh ◽  
Six Degree Of Freedom

This study proposes a formulation for the description of the gear mesh mechanical power loss under the thermal tribodynamic condition. A six degree-of-freedom motion equation set that models the vibratory motions of a general spur gear pair is coupled with the governing equations for the description of the gear thermal mixed elastohydrodynamic lubrication to include the interactions between the gear dynamics and gear tribology disciplines in the modeling of the gear mesh mechanical power loss. The important role of the gear thermal tribo-dynamics in power loss is demonstrated by comparing the predictions of the proposed model to those under the thermal quasi-static condition, and the iso-thermal tribo-dynamic condition, respectively.

A Theoretical Tribological Comparison Between Soft and Hard Coatings of Spur Gear Pairs

2017 ◽  
Vol 139 (3) ◽  
Author(s):  
Huaiju Liu ◽  
Caichao Zhu ◽  
Zhanjiang Wang ◽  
Ye Zhou ◽  
Yuanyuan Zhang
Keyword(s):  
Surface Deformation ◽  
Tribological Behavior ◽  
Elastohydrodynamic Lubrication ◽  
Spur Gear ◽  
Hard Coatings ◽  
Radius Of Curvature ◽  
Maximum Pressure ◽  
Gear Pair ◽  
The Coefficient Of Friction ◽  
Squeeze Effect

A thermal elastohydrodynamic lubrication (TEHL) model is developed for a coated spur gear pair to investigate the effect of soft coatings and hard coatings on the tribological behavior of such a gear pair during meshing. The coating properties, i.e., the ratio of the Young's modulus between the coating and the substrate, and the coating thickness, are represented in the calculation of the elastic deformation. Discrete convolution, fast Fourier transform (DC-FFT) is utilized for the fast calculation of the surface deformation. The variation of the radius of curvature, the rolling speed, the slide-to-roll ratio, and the tooth load along the line of action (LOA) during meshing is taken into account and the transient squeeze effect is considered in the Reynolds equation. Energy equations of the solids and the oil film are derived. The temperature field and the pressure field are solved iteratively. The tribological behavior is evaluated in terms of the minimum film thickness, the maximum pressure, the temperature rise, the coefficient of friction, and the frictional power loss of the tooth contact during meshing. The results show discrepancies between the soft coating results and hard coating results.

An Experimental Methodology to Determine Components of Power Losses of a Gearbox

2021 ◽  
Vol 143 (11) ◽  
Author(s):  
A. Dindar ◽  
K. Chaudhury ◽  
I. Hong ◽  
A. Kahraman ◽  
C. Wink
Keyword(s):  
Power Loss ◽  
Spur Gear ◽  
Rolling Element Bearing ◽  
Experimental Methodology ◽  
Total Power ◽  
Gear Pair ◽  
Rolling Element Bearings ◽  
Power Losses ◽  
Rolling Element ◽  
The One

Abstract In this study, an experimental methodology is presented to separate various components of the power loss of a gearbox. The methodology relies on two separate measurements. One is designed to measure total power loss of a gearbox housing a single spur gear pair under both loaded and unloaded conditions such that load-independent (spin) and load-dependent (mechanical) components can be separated. With the assumption that gear pair and rolling element bearings constitute the bulk of the gearbox power loss, a second measurement system designed to quantify rolling element bearing losses is proposed. With this setup, spin and mechanical power losses of rolling element bearings used in the gearbox experiments are measured. Combining the sets of gearbox and bearing data, power loss components attributable to the gear pair and rolling element bearings are quantified as a function of speed and torque. The results indicate that all gear and bearing related components are significant and a methodology such as the one proposed in this study is warranted.

On Rolling Resistance in Gear Transmission

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
S. S. Ghosh ◽  
G. Chakraborty
Keyword(s):  
Experimental Data ◽  
Friction Force ◽  
Contact Force ◽  
Power Loss ◽  
Degrees Of Freedom ◽  
Rolling Resistance ◽  
Spur Gear ◽  
Gear Transmission ◽  
Gear Pair ◽  
Six Degrees Of Freedom

The effect of rolling resistance on the power loss during gear transmission has been studied. The resistance has been modeled by a lateral shift of the line of action of the contact force. The effect of this shift on the equivalent friction force has been predicted with the help of a six degrees of freedom (DOF) model of a spur gear pair. The predicted results agree closely with the experimental data available in literature.

Investigation on the effect of coating properties on lubrication of a coated spur gear pair

2017 ◽  
Vol 232 (3) ◽  
pp. 277-290 ◽  
Author(s):  
Huaiju Liu ◽  
Caichao Zhu ◽  
Zhanjiang Wang ◽  
Xiangyang Xu ◽  
Jinyuan Tang
Keyword(s):  
Surface Displacement ◽  
Elastohydrodynamic Lubrication ◽  
Spur Gear ◽  
Tooth Surface ◽  
Gear Pair ◽  
Transform Method ◽  
Influence Coefficients ◽  
Stress Components ◽  
Squeeze Effect ◽  
Energy Equations

A thermal elastohydrodynamic lubrication model is proposed for a coated gear pair in which the influence coefficients for the elastic deformation and the subsurface stress components are obtained through the frequency response functions. The generalized Reynolds equation is utilized to represent the non-Newtonian effect. Energy equations of the contacting solids and the oil film are derived and solved based upon the marching method. The discrete convolute, fast Fourier transform method is used for fast calculation of the tooth surface displacement and the stress components underneath the surface. Variations of the slide-to-roll ratio, rolling speed, and the tooth load during gear meshing are considered and the film squeeze effect is taken into account. Effects of the coating thickness on the tribological performance, i.e. the film thickness, the pressure, the frictional behavior as well as the stress components are investigated under both the smooth and rough surface assumptions. Effects of the root mean square value of the tooth surface roughness on the pressure and stresses are discussed.

scholarly journals Demand Analysis of Lubricating Oil in Spur Gear Pairs

2020 ◽  
Vol 10 (16) ◽  
pp. 5417
Author(s):  
Fuchun Jia ◽  
Yulong Lei ◽  
Yao Fu ◽  
Binyu Wang ◽  
Jianlong Hu
Keyword(s):  
Elastohydrodynamic Lubrication ◽  
Spur Gear ◽  
Lubricating Oil ◽  
Transmission Ratio ◽  
Spur Gears ◽  
Control Variate ◽  
Tooth Number ◽  
Oil Demand ◽  
Meshing Process ◽  
Input Torque

Theoretical calculation and numerical simulation are used to investigate the lubricating oil demand of spur gears. In accordance with the function of lubricating oil during the meshing process, oil demand is regarded as the superposition of oil for lubrication and cooling. Oil for lubrication is calculated in accordance with meshing and elastohydrodynamic lubrication (EHL) theories. Oil for cooling is obtained from friction heat. The influence of different meshing positions on lubricating oil demand is analysed, and the effects of modulus, tooth number, transmission ratio, input speed and input torque on lubricating oil demand is investigated using a control variate method. Simulation results indicated that oil for lubrication and oil for cooling have two maxima each during a meshing circle. The influences of different gear parameters and working conditions on lubricating oil demand are compared. The results showed that the oil volume for lubrication increases and oil volume for cooling decreases as the modulus, tooth number and transmission ratio of the gear increase, the oil volume for lubrication and oil volume for cooling increases as the input speed and input torque increase.

Temperature Analysis of Involute Gear Based on Mixed Elastohydrodynamic Lubrication Theory Considering Tribo-Dynamic Behaviors

2014 ◽  
Vol 136 (2) ◽  
Author(s):  
Hui L. Dong ◽  
Ji B. Hu ◽  
Xue Y. Li
Keyword(s):  
Contact Area ◽  
Temperature Rise ◽  
Gear Tooth ◽  
Elastohydrodynamic Lubrication ◽  
Gear Pair ◽  
Rolling Velocity ◽  
Involute Gear ◽  
Tooth Width ◽  
Asperity Contacts ◽  
Tooth Flank

An integrated model is proposed for involute gear pair combining the mixed elastodhydrodynamic lubrication (EHL) theory for finite line contact with surface temperature rise equations considering tribo-dynamic loading behaviors. The film stiffness and viscous damping as well as the friction force are taken into account. The surface topography of tooth flank measured by 3D surface profiler is also included to solve the local temperature and pressure distribution in the contact area. The results show that the temperature distributions in different meshing positions along the line of action exhibit dissimilar characteristics due to the varying of dynamic load and the changing slip-to-roll ratio, which denotes the relationship between sliding velocity and rolling velocity on the tooth flank. Besides, the maximum of temperature is likely to appear at different sides of the gear tooth width as the gear pair meshes along the line of action. Moreover, with the increasing surface roughness, the ratio of asperity contacts becomes larger, so more heat generates from the contact area and leads to higher temperature rise.

Thermal insulation effect on EHL of coated cam/tappet contact during start up

2018 ◽  
Vol 70 (6) ◽  
pp. 917-926 ◽  
Author(s):  
Xianghui Meng ◽  
Changya Yu ◽  
Youbai Xie ◽  
Benfu Mei
Keyword(s):  
Thermal Insulation ◽  
Power Loss ◽  
Elastohydrodynamic Lubrication ◽  
Cold Start ◽  
Content Type ◽  
Friction Power ◽  
Warm Start ◽  
Start Up ◽  
Lubrication Performance ◽  
Insulation Effect

Purpose This paper aims to investigate the lubrication performance of cam/tappet contact during start up. Especially, the thermal insulation effects of coating on the lubrication performance during cold start up process and warm start up process are studied. Design/methodology/approach A numerical model for the analysis of thermal elastohydrodynamic lubrication of coated cam/tappet contact is presented. In this model, the Reynolds equation and the energy equations are discretized by the finite difference method and solved jointly. Findings During start up, the contact force at cam nose-to-tappet contact decreases with increasing time, while the absolute entrainment velocity has the upward trend. The minimum film thickness, maximum average temperature and friction power loss increase with increasing time, while the coefficient of friction decreases during start up. Because of the thermal insulation effect, the coating can significantly increase the degree of temperature rise. Compared with the uncoated case, the coated cam/tappet results in a lower friction power loss. Generally, the friction power loss in the cold start up process is much higher than that in the warm start up process. Originality/value By this study, the lubrication performance and the kinematics and the dynamics of the cam/tappet during start up process are investigated. Meanwhile, the thermal insulation effect of coating is also illustrated. The difference of lubrication performance between cold start up process and warm start up process is analyzed. The results and thermal elastohydrodynamic lubrication method presented in this study can be a guidance in the design of the coated cam/tappet.

Sign in / Sign up

Export Citation Format

Share Document