Deformation and Fracture Behaviors of Polyethylene Coatings on the Natural Gas Transmission Line With Ultraviolet Exposure

1998 ◽  
Author(s):  
Seong-Min Lee ◽  
Sung-Sik Shin ◽  
Hong-Seok Song ◽  
Young-Tai Kho
Keyword(s):  
Mechanical Properties ◽  
Carbon Black ◽  
Fracture Mode ◽  
Uv Exposure ◽  
Uv Resistance ◽  
Deformation And Fracture ◽  
Red Color ◽  
Fracture Behaviors ◽  
Natural Gas Transmission ◽  
Color Pigment

The effect of carbon black, ultraviolet (UV) stabilizer and color pigment on the mechanical property of polyethylene (PE) has been investigated. The transition of fracture mode from ductile to brittle upon UV exposure is identified through microscopic examination of fracture surface. This transition is responsible for the degradation of mechanical properties. The carbon black doped PE shows excellent UV resistance regardless of the presence of UV stabilizer. The mechanical properties of the PE remained unchanged even after 50-days UV exposure. The ductile fracture mode is also maintained in this case. The addition of red color pigment exhibited a very poor UV resistance.

scholarly journals Tensile Deformation and Fracture Behaviors of a Nickel-Based Superalloy via In Situ Digital Image Correlation and Synchrotron Radiation X-ray Tomography

Materials ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2461 ◽  
Author(s):  
Qiang Zhu ◽  
Gang Chen ◽  
Chuanjie Wang ◽  
Heyong Qin ◽  
Peng Zhang
Keyword(s):  
Mechanical Properties ◽  
Synchrotron Radiation ◽  
Digital Image Correlation ◽  
Tensile Deformation ◽  
Image Correlation ◽  
X Ray ◽  
Nickel Based Superalloy ◽  
Deformation And Fracture ◽  
Fracture Behaviors

Nickel-based superalloys have become key materials for turbine disks and other aerospace components due to their excellent mechanical properties at high temperatures. Mechanical properties of nickel-based superalloys are closely related to their microstructures. Various heat treatment processes were conducted to obtain the desired microstructures of a nickel-based superalloy in this study. The effect of the initial microstructures on the tensile deformation and fracture behaviors was investigated via in situ digital image correlation (DIC) and synchrotron radiation X-ray tomography (SRXT). The results showed that the size and volume fraction of γ″ and γ′ phases increased with the aging time. The yield strength and the ultimate tensile strength increased due to the precipitation strengthening at the expense of ductility. The surface strain analysis showed severely inhomogeneous deformation. The local strains at the edge of specimens were corresponded to higher void densities. The fracture of carbides occurred owing to the stress concentration, which was caused by the dislocation accumulation. The fracture mode was dimple coalescence ductile fracture.

Deformation and fracture behavior of an Al-Li-Cu-Mg-Zr alloy 8090

1990 ◽  
Vol 48 (4) ◽  
pp. 974-975
Author(s):  
D.M. Jiang ◽  
B.D. Hong
Keyword(s):  
High Strength ◽  
Deformation And Fracture ◽  
Fracture Behaviors ◽  
Aluminum Lithium ◽  
Carbon Fiber Reinforced Composites ◽  
Peak Aged ◽  
Aluminum Lithium Alloys ◽  
High Strength Aluminum Alloys ◽  
Lithium Alloys ◽  
Zr Alloy

Aluminum-lithium alloys have been recently got strong interests especially in the aircraft industry. Compared to conventional high strength aluminum alloys of the 2000 or 7000 series it is anticipated that these alloys offer a 10% increase in the stiffness and a 10% decrease in density, thus making them rather competitive to new up-coming non-metallic materials like carbon fiber reinforced composites.The object of the present paper is to evaluate the inluence of various microstructural features on the monotonic and cyclic deformation and fracture behaviors of Al-Li based alloy. The material used was 8090 alloy. After solution treated and waster quenched, the alloy was underaged (190°Clh), peak-aged (190°C24h) and overaged (150°C4h+230°C16h). The alloy in different aging condition was tensile and fatigue tested, the resultant fractures were observed in SEM. The deformation behavior was studied in TEM.

Dynamics of Nanoparticle Chain Aggregates of Carbon Under Tension

2003 ◽  
Vol 778 ◽  
Author(s):  
Rajdip Bandyopadhyaya ◽  
Weizhi Rong ◽  
Yong J. Suh ◽  
Sheldon K. Friedlander
Keyword(s):  
Mechanical Properties ◽  
Carbon Black ◽  
Polymer Film ◽  
Elastic Behavior ◽  
Small Strains ◽  
Transmission Electron ◽  
Chain Aggregates ◽  
Nanoparticle Chains ◽  
Reinforcing Filler

AbstractCarbon black in the form of nanoparticle chains is used as a reinforcing filler in elastomers. However, the dynamics of the filler particles under tension and their role in the improvement of the mechanical properties of rubber are not well understood. We have studied experimentally the dynamics of isolated nanoparticle chain aggregates (NCAs) of carbon made by laser ablation, and also that of carbon black embedded in a polymer film. In situ studies of stretching and contraction of such chains in the transmission electron microscope (TEM) were conducted under different maximum values of strain. Stretching causes initially folded NCA to reorganize into a straight, taut configuration. Further stretching leads to either plastic deformation and breakage (at 37.4% strain) or to a partial elastic behavior of the chain at small strains (e.g. 2.3% strain). For all cases the chains were very flexible under tension. Similar reorientation and stretching was observed for carbon black chains embedded in a polymer film. Such flexible and elastic nature of NCAs point towards a possible mechanism of reinforcement of rubber by carbon black fillers.

scholarly journals Enhancement of Chloroprene/Natural/Butadiene Rubber Nanocomposite Properties Using Organoclays and Their Combination with Carbon Black as Fillers

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1085
Author(s):  
Patricia Castaño-Rivera ◽  
Isabel Calle-Holguín ◽  
Johanna Castaño ◽  
Gustavo Cabrera-Barjas ◽  
Karen Galvez-Garrido ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Black ◽  
High Performance ◽  
Rubber Matrix ◽  
Butadiene Rubber ◽  
X Ray Diffraction ◽  
X Ray ◽  
Rubber Blends ◽  
Ft Ir ◽  
Chloroprene Rubber

Organoclay nanoparticles (Cloisite® C10A, Cloisite® C15) and their combination with carbon black (N330) were studied as fillers in chloroprene/natural/butadiene rubber blends to prepare nanocomposites. The effect of filler type and load on the physical mechanical properties of nanocomposites was determined and correlated with its structure, compatibility and cure properties using Fourier Transformed Infrared (FT-IR), X-ray Diffraction (XRD), Thermogravimetric Analysis (TGA) and rheometric analysis. Physical mechanical properties were improved by organoclays at 5–7 phr. Nanocomposites with organoclays exhibited a remarkable increase up to 46% in abrasion resistance. The improvement in properties was attributed to good organoclay dispersion in the rubber matrix and to the compatibility between them and the chloroprene rubber. Carbon black at a 40 phr load was not the optimal concentration to interact with organoclays. The present study confirmed that organoclays can be a reinforcing filler for high performance applications in rubber nanocomposites.

Conductivity and mechanical properties of carbon black-reinforced poly(lactic acid) (PLA/CB) composites

2021 ◽  
Author(s):  
Jipeng Guo ◽  
Chi-Hui Tsou ◽  
Yongqi Yu ◽  
Chin-San Wu ◽  
Xuemei Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Carbon Black ◽  
Poly Lactic Acid

scholarly journals Electromagnetic Interference Shielding and Physical-Mechanical Characteristics of Rubber Composites Filled with Manganese-Zinc Ferrite and Carbon Black

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 616
Author(s):  
Ján Kruželák ◽  
Andrea Kvasničáková ◽  
Klaudia Hložeková ◽  
Rastislav Dosoudil ◽  
Marek Gořalík ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Black ◽  
Zinc Ferrite ◽  
Mechanical Characteristics ◽  
Hybrid Composites ◽  
Rubber Matrix ◽  
Butadiene Rubber ◽  
Frequency Range ◽  
Manganese Zinc ◽  
Manganese Zinc Ferrite

In the present work, composite materials were prepared by incorporation of manganese-zinc ferrite, carbon black and combination of ferrite and carbon black into acrylonitrile-butadiene rubber (NBR). For cross-linking of composites, standard sulfur-based curing system was applied. The main goal was to investigate the influence of the fillers on the physical-mechanical properties of composites. Then, the electromagnetic absorption shielding ability was investigated in the frequency range 1 MHz–3 GHz. The results revealed that composites filled with ferrite provide sufficient absorption shielding performance in the tested frequency range. On the other hand, ferrite behaves as an inactive filler and deteriorates the physical-mechanical characteristics of composites. Carbon black reinforces the rubber matrix and contributes to the improvement of physical-mechanical properties. However, composites filled with carbon black are not able to absorb electromagnetic radiation in the given frequency range. Finally, the combination of carbon black and ferrite resulted in the modification of both physical-mechanical characteristics and absorption shielding ability of hybrid composites.

scholarly journals Mechanical Properties and Biocompatibility of Urethane Acrylate-Based 3D-Printed Denture Base Resin

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 822
Author(s):  
Jy-Jiunn Tzeng ◽  
Tzu-Sen Yang ◽  
Wei-Fang Lee ◽  
Hsuan Chen ◽  
Hung-Ming Chang
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Flexural Modulus ◽  
Measurement Data ◽  
Uv Exposure ◽  
Control Group ◽  
Urethane Acrylate ◽  
Shore Hardness ◽  
Digital Light Processing ◽  
Denture Base

In this study, five urethane acrylates (UAs), namely aliphatic urethane hexa-acrylate (87A), aromatic urethane hexa-acrylate (88A), aliphatic UA (588), aliphatic urethane triacrylate diluted in 15% HDD (594), and high-functional aliphatic UA (5812), were selected to formulate five UA-based photopolymer resins for digital light processing (DLP)-based 3D printing. Each UA (40 wt%) was added and blended homogenously with ethoxylated pentaerythritol tetraacrylate (40 wt%), isobornyl acrylate (12 wt%), diphenyl (2,4,6-trimethylbenzoyl) phosphine oxide (3 wt%), and a pink acrylic (5 wt%). Each UA-based resin specimen was designed using CAD software and fabricated using a DLP 3D printer to specific dimensions. Characteristics, mechanical properties, and cytotoxicity levels of these designed UA-based resins were investigated and compared with a commercial 3D printing denture base acrylic resin (BB base) control group at different UV exposure times. Shore hardness-measurement data and MTT assays were analyzed using a one-way analysis of variance with Bonferroni’s post hoc test, whereas viscosity, maximum strength, and modulus were analyzed using the Kruskal–Wallis test (α = 0.05). UA-based photopolymer resins with tunable mechanical properties were successfully prepared by replacing the UA materials and the UV exposure times. After 15 min of UV exposure, the 5812 and 594 groups exhibited higher viscosities, whereas the 88A and 87A groups exhibited lower viscosities compared with the BB base group. Maximum flexural strength, flexural modulus, and Shore hardness values also revealed significant differences among materials (p < 0.001). Based on MTT assay results, the UA-based photopolymer resins were nontoxic. In the present study, mechanical properties of the designed photopolymer resins could be adjusted by changing the UA or UV exposure time, suggesting that aliphatic urethane acrylate has good potential for use in the design of printable resins for DLP-type 3D printing in dental applications.

Sign in / Sign up

Export Citation Format

Share Document